ENGLISH
Congratulations on your purchase
and welcome to Philips! To fully
benet from the support that Philips
oers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving unit
3 Ag+ antibacterial feature (S110 only)
4 On/o slide
5 Socket for small plug
6 Cleaning brush
7 Supply unit (adapter, type A00390)
8 Small plug
Important safety
information
Read this important information
carefully before you use the appliance
and save it for future reference.
Danger
- Keep the supply unit
dry (Fig. 2).
Warning
- To charge the
battery, only use the
detachable supply
unit (type A00390)
provided with the
appliance.
- The supply
unit contains a
transformer. Do not
cut o the supply
unit to replace it with
another plug, as this
causes a hazardous
situation.
- This appliance can
be used by children
aged from 8 years
and above and
persons with reduced
physical, sensory or
mental capabilities
or lack of experience
and knowledge if
they have been
given supervision or
instruction concerning
use of the appliance
in a safe way and
understand the
hazards involved.
Children shall not play
with the appliance.
Cleaning and user
maintenance shall not
be made by children
without supervision.
- Always unplug the
shaver before you
clean it under the tap.
- Always check the
appliance before you
use it. Do not use
the appliance if it is
damaged, as this may
cause injury. Always
replace a damaged
part with one of the
original type.
- Do not open the
appliance to replace
the rechargeable
battery.
Caution
- Never immerse the
cleaning system or the
charging stand in water
and do not rinse it
under the tap (Fig. 2).
- Never immerse the
shaver in water. Do
not use the shaver
in the bath or in the
shower.
- Never use water
hotter than 80°C to
rinse the shaver.
- Only use this
appliance for its
intended purpose
as shown in the user
manual.
- For hygienic reasons,
the appliance should
only be used by one
person.
- Never use
compressed air,
scouring pads,
abrasive cleaning
agents or aggressive
liquids such as petrol
or acetone to clean
the appliance.
- If your shaver comes
with a cleaning
system, always
use the original
Philips cleaning uid
(cartridge or bottle,
depending on the
4222.002.5959.1
1
2
4
3
5
6
7
8
S100 series
S110, S106, S100
>75% recycled paper
>75%
2
5
8
3
6
9
4
7
10
11 12 13
14
1
2
15 16
17 18 19
20 21
2
1
22
23
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may
even become slightly irritated. This is
normal. Your skin and beard need time
to adapt to any new shaving system.
To allow your skin to adapt to this new
appliance, we advise you to shave
regularly (at least 3 times a week) and
exclusively with this appliance for a
period of 3 weeks.
1 Switch on the appliance.
2 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 7).
Note: Shave on a dry face only.
Do not use the shaver in
combination with shaving gel,
shaving foam or water.
3 Clean the appliance after use.
Cleaning and maintenance
Cleaning the shaver under the tap
Clean the shaver after every shave for
optimal performance.
Caution: Be careful with hot water.
Always check if the water is not too
hot, to prevent burning your hands.
Caution: Never dry the shaving unit
with a towel or tissue, as this may
damage the shaving heads.
1 Switch o the appliance and
disconnect it from the power outlet.
2 Rinse the shaving unit under a
warm tap (Fig. 8).
- For additional cleaning you can
also start by using the cleaning
brush to remove hairs (Fig. 9).
3 Pull the shaving unit o the shaver
in a straight upward movement
(Fig. 10).
4 Rinse the shaving unit and hair
chamber under a warm tap
(Fig. 11, Fig. 12).
- For additional cleaning you can
also start by using the cleaning
brush to remove hairs.
5 Carefully shake o excess water
and let the shaving unit and hair
chamber dry (Fig. 13).
6 Put the shaving unit back onto the
shaver (Fig. 14).
Every two months: shaving
heads
Note: Do not use cleaning agents or
alcohol to clean the shaving heads.
Only use Philips Cleaning Spray (HQ110).
type of cleaning
system).
- Always place the
cleaning system on
a stable, level and
horizontal surface to
prevent leakage.
- If your cleaning
system uses a
cleaning cartridge,
always make
sure the cartridge
compartment is
closed before you use
the cleaning system
to clean or charge the
shaver.
- When the cleaning
system is ready for
use, do not move it
to prevent leakage of
cleaning uid.
- Water may drip from
the socket at the
bottom of the shaver
when you rinse it.
This is normal and not
dangerous because
all electronics are
enclosed in a sealed
power unit inside the
shaver.
- Do not use the
supply unit in or near
wall sockets that
contain an electric air
freshener to prevent
irreparable damage to
1 Switch o the shaver, remove
the adapter from the wall socket
and pull the small plug out of the
shaver.
2 Pull the shaving unit o the shaver
in a straight upward movement
(Fig. 10).
3 Turn the orange wheel
anticlockwise and remove the
retaining frame (Fig. 15).
4 Remove and clean one shaving
head at a time. Each shaving head
consists of a cutter and a guard
(Fig. 16).
Note: Do not clean more than
one cutter and guard at a time,
since they are all matching sets.
If you accidentally put a cutter in
the wrong shaving guard, it may
take several weeks before optimal
shaving performance is restored.
5 Remove the guard from the cutter
(Fig. 17).
6 Clean the cutter and guard under
the tap (Fig. 18, Fig. 19).
- For additional cleaning you can
also start by using the cleaning
brush to remove hairs.
7 Put the cutter back into the guard
after cleaning (Fig. 20).
8 Put the shaving heads back into the
shaving unit (Fig. 21).
9 Put the retaining frame back into
the shaving unit and turn the
orange wheel clockwise (Fig. 22).
10 Put the shaving unit back onto the
shaver (Fig. 14).
Storage
We advise you to let the shaver dry
before you put the protection cap on it.
1 Switch o the shaver.
2 Put the protection cap on the
shaver after use to prevent damage
and to avoid dirt accumulation in
the shaving heads (Fig. 23).
Replacement
For maximum shaving performance,
we advise you to replace the shaving
heads every two years. Replace
damaged shaving heads immediately.
Always replace the shaving heads
with original Philips shaving heads
as specied in the chapter ‚Ordering
accessories‘.
For instructions on how to remove the
shaving heads, see chapter ‚Cleaning
and maintenance‘, section ‚Every two
months: shaving heads‘.
the supply unit.
Electromagnetic elds (EMF)
- This Philips appliance complies
with all applicable standards and
regulations regarding exposure to
electromagnetic elds.
General
- This shaver can be safely cleaned
under the tap (Fig. 3).
- The appliance is suitable for
mains voltages ranging from
100 to 240 volts.
- The supply unit transforms
100-240 volts to a safe low
voltage of less than 24 volts.
Charging
Charging takes approx. 10 hours. A fully
charged shaver has a shaving time of
up to 20 minutes.
- Charge the appliance when the
motor stops or starts running
slower. For optimal performance,
only charge the shaver when the
battery is low.
- Make sure the shaver is switched
o when you start to charge it.
- When you charge the shaver for the
rst time or after a long period of
non-use, let it charge continuously
for 12 hours. Charging normally
takes 10 hours.
Caution: Do not leave the appliance
connected to the power outlet for
more than 24 hours.
Note: You cannot use the appliance
while it is charging.
1 Make sure the appliance is
switched o.
2 Put the supply unit in the wall
socket and put the small plug in the
appliance (Fig. 4).
3 After charging, remove the supply
unit from the wall socket and pull
the small plug out of the appliance.
Using the appliance
Note: This appliance can only be used
without cord (Fig. 5).
Switching the appliance on and
o
- To switch on the appliance, push
the on/o slide upwards (Fig. 6).
- To switch o the appliance, push
the on/o slide downwards (Fig. 6).
Ordering accessories
To buy accessories or spare parts,
visit www.shop.philips.com/service
or go to your Philips dealer. You can
also contact the Philips Consumer
Care Centre in your country (see
the worldwide guarantee leaet for
contact details).
The following accessories and spare
parts are available:
- A00390 adapter
- SH30 Philips shaving heads
HQ110 Philips shaving head
cleaning spray
Recycling
Do not throw away the product with
the normal household waste at the
end of its life, but hand it in at an
ocial collection point for recycling.
By doing this, you help to preserve the
environment.
This product contains a built-in
rechargeable battery which shall not
be disposed of with normal household
waste. We strongly advise you to take
your product to an ocial collection
point or a Philips service centre to
have a professional remove the
rechargeable battery.
Follow your country’s rules for the
separate collection of electrical and
electronic products and rechargeable
batteries. Correct disposal helps
prevent negative consequences for the
environment and human health.
Removing the rechargeable
battery
Only remove the rechargeable
battery when you discard the
shaver. Before you remove the
battery, make sure that the shaver
is disconnected from the wall
socket and that the battery is
completely empty
Take any necessary safety
precautions when you handle tools
to open the shaver and when you
dispose of the rechargeable battery.
1 Check if there are screws in the
back of the shaver or in the hair
chamber. If so, remove them.
2 Remove the outer panels of the
shaver with a screwdriver or other
tool. If necessary, also remove
additional screws and/or parts until
you see the printed circuit board
with the rechargeable battery.
3 Remove the rechargeable battery.
The
appli ance
makes a
strange
noise.
Too
much
dirt has
collected
in the
shaving
heads.
Clean the
shaving
heads (see
'Cleaning and
maintenan-
ce'). After
cleaning,
lubricate
the central
point on the
inside of the
guards with
Philips Cle-
aning Spray
(HQ110).
The
shaving
heads are
damaged
or worn.
Replace
the shaving
heads (see
'Replace-
ment').
I con nect-
ed the
appli ance
to the
mains, but
I was not
able to
(nish my)
shave.
The
recharge-
able
battery is
empty.
The shaver
does not
run from the
mains. When
the battery
is empty,
you have to
recharge the
battery and
then unplug
the shaver
before you
can use the
shaver again.
Warranty and support
If you need information or support,
please visit www.philips.com/support
or read the international warranty leaet.
Warranty restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they
are subject to wear.
Troubleshooting
This chapter summarizes the most
common problems you could
encounter with the appliance.
If you are unable to solve the problem
with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact
the Consumer Care Center in your
country.
Prob lem Possible
cause
Solution
The shav-
er does
not shave
as well as
it used to.
The
shaving
heads are
dirty. You
have not
cleaned
the
shaver
well
enough
or you
have not
cleaned it
for a long
time.
Clean the
shaving
heads
thoroughly
before you
continue
shaving (see
'Cleaning
and mainte-
nance').
Long
hairs
obstruct
the
shaving
heads.
Clean the
cutters and
guards (see
'Every two
months:
shaving
heads').
繁體中文
感謝您購買本產品。歡迎
來到飛利浦的世界！ 為充
分享受飛利浦為您提供的
好處，請至下列位址註冊
產品：www.philips.com/
welcome。
一般說明 (圖 1)
1 保護蓋
2 除毛刀頭組
3 銀離子抗菌功能
(僅限S110)
4 On/Off滑動開關
5 小插頭插座
6 清潔刷
7 電源供應裝置(電源轉換
器，型號A00390)
8 小插頭
重要安全資訊
使用本產品前，請先仔細閱
讀此重要資訊，並保留說明
以供日後參考。
危險
- 電源供應裝置請保持乾燥
(圖 2)。
警示
- 如需為電池充電，僅可使用
裝置隨附的可拆式電源供應
裝置 (型號：A00390)。
- 電源供應裝置內含一個變
壓器。 請勿切斷電源供
應裝置而以其他的插頭取
代，否則會造成危險。
- 本產品可供 8 歲以上兒
童、身體官能或心智能力
退化者，或是經驗與使用
知識缺乏者使用，但需有
人從旁監督或指示如何安
全使用本產品，且使用者
需了解使用本產品的潛在
Prob lem Possible
cause
Solution
You
mixed up
the cut-
ters and
guards
when
you
placed
them
back
into the
retaining
frame
after
cleaning.
Put each
cutter in the
other guard.
If you do
not switch
the cutters,
it may take
2 to 3 weeks
until optimal
shaving
performance
is restored.
The
shaving
heads are
damaged
or worn.
Replace
the shaving
heads.
The
shaver
does
not work
when
I push
the on/
o slide
upward s.
The
recharge-
able
battery is
empty.
Recharge the
battery (see
'Charging').
My skin is
irritated
after
shaving.
Your skin
needs
time to
get used
to the
Philips
shaving
system.
Skin irritation
during the
rst 2-3 weeks
of use is
possible.
After this
period, the
skin irritation
usually
disappears.
The
rotation
speed of
the shav-
ing heads
is slower
than
usual.
Too
much
dirt has
collected
in the
shaving
heads.
Clean the
shaving
heads (see
'Cleaning and
mainte-
nance').
The
recharge-
able
battery is
low.
Recharge the
battery (see
'Charging').
危險。 請勿讓小孩把玩本
產品。 若無人監督，請勿
讓兒童進行清潔和使用者
維護。
- 在水龍頭下沖洗電鬍刀之
前，請先拔掉電鬍刀的插
頭。
- 使用前請務必檢查本產
品。 若產品受損請勿使
用，以免受傷。 零件如有
受損，請務必以原型號更
換之。
- 請勿拆開本產品更換充電
式電池。
警告
- 切勿將清潔系統或充電座
浸入水中，或直接在水龍
頭下沖洗 (圖 2)。
- 請勿將電鬍刀浸泡在水
中。 請勿在泡澡或淋浴時
使用電鬍刀。
- 切勿使用超過 80°C 的熱
水沖洗電鬍刀。
- 本產品儘限用於本使用手
冊所述之相關用途。
- 為保衛生起見，請勿多人
共用本產品。
- 絕對不可使用壓縮空氣、
鋼絲絨、磨蝕性的清潔劑
或侵蝕性的液體 (例如汽
油或丙酮) 清潔本產品。
- 如果您的電鬍刀配備清潔
系統，請務必使用飛利浦
原廠清潔液 (補充匣或補
充瓶，依清潔系統的類型
而定)。
- 請務必將清潔系統放置在
穩固、平整的水平面上，
以防滲漏。
- 如果您的清潔系統使用的
是補充匣，在使用清潔系
統清潔電鬍刀或為電鬍刀
充電之前，請務必確定補
充匣室已關閉。
清潔與維護
將電鬍刀放在水龍頭下沖洗
為達到最佳性能，請於每回
刮鬍之後清潔電鬍刀。
警告： 使用熱水時請小心。
隨時檢查熱水是否太燙，
以避免手部燙傷。
警告： 切勿使用毛巾或紙巾
擦乾電鬍刀組，否則可能會
造成電鬍刀刀頭損壞。
1 關閉產品電源，並將產品
插頭從插座拔下。
2 將電鬍刀組以溫水(圖8)
沖洗。
- 如要進行額外的清潔，您
可先從使用清潔刷清除鬍
渣(圖9)開始。
3 以垂直向上拉起的方式
(圖10)，將電鬍刀組自電
鬍刀上取下。
4 在 水龍頭(圖11圖12)下
以溫水沖洗電鬍刀組與鬍
渣室。
- 如要進行額外的清潔，
您可先從使用清潔刷清除
鬍渣開始。
5 仔細甩乾多餘的水份之
後，讓電鬍刀組與鬍渣室
乾燥(圖13)。
6 將電鬍刀組裝回電鬍刀
(圖14)上。
每兩個月： 電鬍刀刀頭
注意： 請勿使用清潔劑或
酒精清潔電鬍刀刀頭， 務
必使用飛利浦噴霧清潔劑
(HQ110)。
1 關閉電鬍刀電源，將轉換
器從電源插座拔下，並將
小插頭自電鬍刀上拔下。
2 以垂直向上拉起的方式
(圖10)，將電鬍刀組自電
鬍刀上取下。
- 當清潔系統準備就緒可供
使用時，應避免移動它，
以防清潔液漏出。
- 在您沖洗時，電鬍刀底部
的插孔可能會滴水。 此為
正常現象，並不會造成危
險，因為所有的電子零件
都密封於電鬍刀內的電力
裝置中。
- 請勿在插入電子空氣清淨
機的牆壁插座內或附近使
用電源供應裝置，以免電
源供應裝置發生無法修復
的損壞。
電磁波 (EMF)
- 本Philips產品符合所有電
磁場暴露的相關適用標準
和法規。
一般
- 此電鬍刀可在水龍頭下
(圖3)安全地清洗。
- 本產品適用於100到
240伏特的插座電壓。
- 電源供應裝置可以將
100-240伏特的電壓轉換
為低於24伏特的安全低
電壓。
充電
充電時間約需 10 個小時。
完全充電的電鬍刀可持續刮
鬍約 20 分鐘。
- 請在馬達停止轉動時或者
運轉速度開始變慢時，為
產品充電。為達到最佳性
能，只有在電力不足時，
才需要替電鬍刀充電。
- 開始充電之前，務必將電
鬍刀的電源關閉。
- 第一次為電鬍刀充電時，
或長期未用後，請連續充
電12小時。正常的充電
約需10小時。
3 以逆時針方向轉動橘色轉
盤，將固定架(圖15)拆
下。
4 一次取下並清洗一個刀
頭。每個電鬍刀刀頭都是由
刀具和刀網(圖16)組成。
注意：刀具及刀網是成對
組合，請勿一次清潔超過一
組。如果您不小心將刀片
放進錯誤的電鬍刀刀網中，
可能要花幾週的時間才能恢
復最理想的刮鬍效果。
5
取 下 刀具(圖17)的刀網。
6 將刀片及刀網放在水龍頭
(圖18圖19)下清洗。
- 如要進行額外的清潔，
您可先從使用清潔刷清除
鬍渣開始。
7 清潔(圖20)後，將刀具
放回刀網中。
8 將電鬍刀刀頭裝回電鬍刀
組(圖21)。
9 將固定架裝回電鬍刀組，
並以順時針方向(圖22)
轉動橘色轉盤。
10 將電鬍刀組裝回電鬍刀
(圖14)上。
存放
我們建議您先將電鬍刀晾
乾，再蓋上保護蓋。
1請關閉電鬍刀電源。
2使用後請為電鬍刀蓋上
保護蓋以防損壞，並避
免污垢累積在電鬍刀刀
頭(圖23)中。
更換
為達到最佳刮鬍性能，我們
建議您每兩年更換一次電鬍
刀刀頭。 刀頭若受損，請
立即更換。 更換電鬍刀刀
頭時，請一律使用「訂購配
件」單元中所指明的原廠飛
警告： 請勿讓產品連續連接
電源插座超過 24 小時。
注意：您無法在充電時使用
本產品。
1 確定關閉本產品的電源。
2 將電源供應裝置插入牆壁
的插座，並將小插頭插入
產品(圖4)中。
3 充電完畢請將電源供應裝
置拔離電源插座，並將小
插頭從產品上拔除。
使用本產品
注意：本產品只能以無線
(圖5)方式使用。
開啟及關閉本產品
- 若要開啟本產品電源，
請將on/off開關往上
(圖6)推。
- 若要關閉本產品電源，
請將on/off開關往下
(圖6)推。
皮膚適應期
您第一次刮鬍的結果可能不
如您所預期，皮膚甚至可能
稍微刺痛。 這是正常現象。
您的皮膚與鬍鬚需要時間適
應新的刮鬍系統。 建議您用
這把電鬍刀定期刮鬍 (每週至
少 3 次) 為期 3 週，讓您的
肌膚適應新的電鬍刀。
1 開啟產品電源。
2 讓電鬍刀刀頭在皮膚上移
動。請同時用直線及畫圓
的方式來移動(圖7)。
注意：僅可乾刮。使用電
鬍刀時，請勿搭配刮鬍凝
露、刮鬍泡或水。
3 使用後需清潔本產品。
利浦電鬍刀刀頭。
有關如何取下電鬍刀刀頭的
說明，請參閱「清潔與維
護」單元之「每兩個月：
電鬍刀刀頭」一節。
訂購配件
若要購買配件或備用零件，
請造訪 www.shop.philips.com/
service，或洽詢您的飛利浦
經銷商。 您也可以聯絡您所
在國家/地區的飛利浦客戶服
務中心 (詳細聯絡資料請參閱
全球保證書)。
備有下列配件及備用零件可
供另外選購：
- A00390變壓器
- SH30飛利浦電鬍刀頭
- HQ110飛利浦電鬍刀刀頭
噴霧清潔劑
回收
- 本產品使用壽命結束時請
勿與一般家庭廢棄物一併
丟棄。請將該產品放置於
政府指定的回收站，此舉
能為環保盡一份心力。
- 本產品包含內建充電式電
池，不得與一般家用廢棄
物一併丟棄。強烈建議您
將產品攜至政府指定的回
收站或Philips服務中心，
由專業人員取出充電式電
池。
- 請按照您所在國家/地區的
規定，分類與回收電子電
器產品及充電式電池。正
確處理廢棄產品有助於避
免對環境和人類健康帶來
負面影響。
把每一
片刀具
放入另
一個刀
網。如
果您沒
有調換
刀具，
可能要
花2到
3週的
時間才
能恢復
最理想
的刮鬍
效果。
電鬍刀
刀頭毀
壞或磨
損。
更換刀
頭。
將On/
Off滑
動開關
往上
推，但
電鬍刀
無法運
作。
充電式
電池沒
電。
將電池
(見'充電')
重新充
電。
刮鬍之
後，皮
膚感到
刺痛。
您的皮
膚需要
一些時
間才能
適應飛
利浦電
鬍刀系
統。
開始使用
的第2到
3週，皮
膚可能會
有過敏現
象。過
了這段時
間，皮膚
過敏的症
狀通常會
消失。
刀頭的
旋轉速
度比平
常緩
慢。
過多污
垢累積
在電鬍
刀刀頭
中。
清潔刀頭
(見'清潔
與維護')
。
取出充電式電池
請僅在棄置電鬍刀前取出充
電式電池。 取出電池前，請
確認電鬍刀已從牆上插座拔
出，且電池電力已完全耗盡
使用工具打開電鬍刀或棄置
充電式電池時，請採取任何
必要的安全預防措施。
1 檢查電鬍刀背面或鬍渣室
是否有螺絲。如有的話請
拆下。
2 使用螺絲起子或其他工具
拆除電鬍刀外部面板。
必要時，也可拆下其他螺
絲和/或零件，直到清楚看
見印刷電路板與充電式電
池為止。
3 取出充電式電池。
保固與支援
如需資訊或支援，請造訪：
www.philips.com/support，
或另行參閱全球保證書。
保固限制
電鬍刀刀頭 (刀具和刀網)
由於其耗損性，因此不在全
球保固範圍內。
疑難排解
本章概述了使用本產品最常
遇到的問題。 如果無法利用
以下資訊解決遇到的問題，
請造訪 www.philips.com/
support 瀏覽常見問題清單，
或聯絡您所在國家/地區的飛
利浦客戶服務中心。
充電式
電池
電力不
足。
將電池
(見'充電')
重新充
電。
產品發
出奇怪
的噪
音。
過多污
垢累積
在電鬍
刀刀頭
中。
清潔刀頭
(見'清潔
與維護')
。清潔
後，請使
用飛利
浦噴霧
清潔劑
(HQ110)
潤滑刀網
內側的中
心點。
電鬍刀
刀頭毀
壞或磨
損。
更換刀頭
(見'更換')
。
我已將
本產品
連接電
源，但
無法
(完成)
刮鬍。
充電式
電池沒
電。
電鬍刀無
法插電運
轉。電池
電力耗盡
時，您必
須先讓電
池充電，
然後拔掉
電鬍刀的
插頭，才
能再度使
用電鬍
刀。
問題 可能原
因
解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀
刀頭
髒污。
電鬍刀
清潔不
夠徹底
或是太
久沒有
清潔。
在您繼續
刮鬍
(見'清潔
與維護')
之前，
請徹底清
潔刀頭。
問題 長鬍鬚
卡住電
鬍刀刀
頭。
清潔刀片
及刀網
(見'每兩
個月：電
鬍刀刀
頭')。
長鬍鬚
卡住電
鬍刀刀
頭。
清潔刀
具及刀
網後，
將其放
回固定
架時，
把刀具
及刀網
混在一
起。
把每一片
刀具放入
另一個刀
網。如果
您沒有調
換刀具，
可能要花
2到3週
的時間才
能恢復最
理想的刮
鬍效果。
-
1
-
2
-
3
-
4
-
5
