Bitspower BP-ETW インストールガイド

タイプ
インストールガイド
安裝方式/Installation/安装方式
G1/4" Silver Shining Water-Exhaust Fitting
V2/第二版
注意,跑水前,請先確認所有零件已安裝在正確的位置上,在不開主機,單開水泵的情况下,進行24小時的跑水測試, 確保無漏水情况後再開主機,避免發生漏水而導致電腦零件的損壞。
注意,跑水前,请先确认所有零件已安装在正确的位置上,在不开主机,单开水泵的情况下,进行24小时的跑水测试, 确保无漏水情况后再开主机,避免发生漏水而导致电脑零件的损坏。
Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test
with only the pump connected to the power supply .
本公司保留對產品的設計更改以及解釋的權力,如有更動恕不另行通知,產品顏色與配件以實物為準。
本公司保留对产品的设计更改以及解释的权力,如有更动恕不另行通知,产品颜色与配件以实物为准。
Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.
BP-ETW
建議將洩水接頭安裝於水冷系統的最低點。
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
建议将泄水接头安装于水冷系统的最低点。
Step 2
換上洩水配件,旋入配件過程中即會逐漸洩
水,建議外接管線以利洩水。
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
换上泄水配件,旋入配件过程中即会逐渐泄
水,建议外接管线以利泄水。
Step 1
將洩水接頭上蓋旋起。
Unscrew the top of the water-exhaust fitting.
将泄水接头上盖旋起。
注意:Bitspower建議消費者使用蒸餾水、純凈水,加入Bitspower的染劑作為水冷液使用;如客戶自行選購的水冷液導致電鍍層剝落、
水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致漏水等及其它不可抗力之問題時,消費者自行承擔相關產品責任。
未注水前,請勿啟動水泵電源。
注意:Bitspower 建议消费者使用蒸馏水、纯净水,加入Bitspower的染剂作为水冷液使用;如客户自行选购的水冷液导致电镀层剥落、
水道堵塞、水泵转动不正常、水箱管破裂或密封圈变型以致漏水等及其它不可抗力之问题时,消费者自行承担相关产品责任。
未注水前,请勿启动水泵电源。
Notice:
Bitspower recommends that consumers add the Bitspower dye to distilled water or purified water for their water-cooling
liquid. If the consumer chooses different water-cooling liquids, the resulting impurities may cause peeling of the coating
on some of the hardware, water channels blockage by built-up residue, improper operation of the water pump, water
tank tube breakage, and o-rings deformation leading to leakage. Any issues related to the use of inappropriate
water-cooling liquid will be the responsibility of the consumer.
Do not turn on the pump if the reservoir is empty.
  • Page 1 1

Bitspower BP-ETW インストールガイド

タイプ
インストールガイド

他の言語で