Dell Energy Smart Rack Enclosure クイックスタートガイド

Dell Energy Smart Rack

Enclosure

Installation Guide

Guide d'installation

Installationsanleitung

設置ガイド

Guía de instalación

Dell Energy Smart Rack

Enclosure

Installation Guide

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

2011-04 P/N GY60R Rev. A00

Contents 3

Contents

Safety Instructions. . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems

. . . . . . . . . 5

Rack Installation Instructions

. . . . . . . . . . . . . . . 6

Rack Specifications

. . . . . . . . . . . . . . . . . 6

Before You Begin

. . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies

. . . . . . . . . . 8

Installing Rack Cabinets

. . . . . . . . . . . . . . . 8

Opening and Closing the Front Rack Door

. . . . . . 9

Removing and Replacing the Rack Doors

. . . . . . 9

Removing and Replacing the Side Panels

. . . . . 13

Installing the Brushes

. . . . . . . . . . . . . . . 16

Removing and Replacing the Extension

Service Cover

. . . . . . . . . . . . . . . . . . . . 18

Removing and Replacing the Extension

. . . . . . 20

Reversing the Front Door (Optional)

. . . . . . . . 21

Securing the Rack Leveling Feet

. . . . . . . . . . 29

Installing the Rack Stabilizer Feet

. . . . . . . . . 31

Adjusting the Rear Rack Posts (Optional)

. . . . . 34

Routing Cables

. . . . . . . . . . . . . . . . . . . 36

Coupling Two Racks

. . . . . . . . . . . . . . . . . . . 41

4 Contents

Installation Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to

protect your equipment and working environment from potential damage.

For complete safety and regulatory information, see the safety instructions

that shipped with your equipment. Warranty information may be included in

this document or as a separate document.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also see the

rack installation documentation accompanying the system and the rack for

specific caution statements and procedures.

Systems are considered to be components in a rack. Component refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Instructions for Rack-Mounted Systems:

• Your rack kit has been approved only for the rack cabinet provided.

It is your responsibility to ensure that installation of the equipment

into any other rack complies with all applicable standards. Dell disclaims

all liability and warranties with respect to combinations of equipment

with any other rack.

• The rack enclosure is cooled by air through the vented tiles of a raised

floor. The rack enclosure should be positioned over the vented tiles before

installing components in the enclosure.

• Before installing your equipment in a rack, ensure that the rack is properly

secured as directed in "Installing the Rack Stabilizer Feet" on page 31.

• Always load from the bottom up and load the heaviest items first.

• Do not overload the AC power supply branch circuit that provides

power to the rack.

• Do not stand or step on any components in the rack.

6 Installation Guide

• The air channel located at the bottom of the rack is used to direct cool air

from the floor to the front of the rack enclosure. The air channel must

always

remain at the bottom of the rack (in 1U and 2U) and must not be

moved to a different location in the rack.

• Do not use the air channel as a step or as a shelf to support components.

WARNING: All brushes supplied must be installed and the brush bristles must be

in contact with the floor to form a seal around the bottom perimeter of the rack

enclosure. Removing the brushes may reduce the cooling efficiency within the

enclosure.

WARNING: The extension service cover must only be removed when installing or

removing components from the upper rack unit spaces and must be reinstalled

immediately. Components in the rack may overheat if the extension service cover

is not installed in the rack enclosure.

Rack Installation Instructions

This installation guide provides instructions for trained service technicians

installing a rack enclosure. Information includes assembling the rack,

coupling two racks, and routing cables through the rack. The rack can be

installed using the recommended tools.

Before attempting this installation, read through this entire procedure carefully.

Rack Specifications

NOTE: The rack meets the specifications of American National Standards Institute

(ANSI), Electronics Components Association (ECA) Standard EIA/ECA-310-E,

International Electrotechnical Commission (IEC) 60297-3-100, and Deutsche Industrie

Norm (DIN) 41494.

Installation Guide 7

Before You Begin

WARNING: Before you begin installing your rack, carefully read "Important

Safety Information" on page 7 and the safety instructions that came with the rack.

WARNING: When installing multiple systems in a rack, complete all the

procedures for the current system before attempting to install the next system.

WARNING: Rack cabinets can be extremely heavy and can move easily on the

casters. The cabinet has no brakes. Use extreme caution while moving the rack

cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid long or

steep inclines, rough surfaces, or ramps where loss of cabinet control may occur.

Extend the leveling feet for support and to prevent the cabinet from rolling.

WARNING: Avoid rolling the rack cabinet over rough surfaces. Hard impacts to

the casters could cause them to break and the rack can become unstable and may

tip over.

WARNING: Do not attempt to move your rack with components installed. If you

move a fully loaded rack on a slightly uneven surface, the rack can become

unstable and may tip over.

Important Safety Information

Observe the safety precautions in the following subsections when installing

your system in the rack.

WARNING: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy and proper preparation and planning are important to prevent injury

to yourself and to others. This becomes increasingly important when systems

are installed high up in the rack. Also verify that the vented tiles and floor sub-

structure are rated to support the weight of the rack enclosure with all the

components installed.

WARNING: Before installing systems in a rack, install front and side stabilizers

on stand-alone racks or the front stabilizers on racks joined to other racks.

Failure to install stabilizers accordingly before installing systems in a rack

could cause the rack to tip over, potentially resulting in bodily injury under certain

circumstances.

WARNING: After installing systems in a rack, never pull more than one system

out of the rack on its slide assemblies at one time. The weight of more than one

extended system could cause the rack to tip over and cause injury.

8 Installation Guide

Recommended Tools and Supplies

You may need the following tools and supplies to install the rack:

• #2 Phillips cross-tip screwdriver

• Flat head screwdriver

• 12 mm wrench

• 10 mm wrench (for reversing the front door)

• T20 Torx screwdriver (for reversing the front door)

• T30 Torx screwdriver (for reversing the front door)

• Keys to the rack doors and side panels

• 6 mm Allen wrench

• Adjustable wrench (for removing the rack from the pallet)

Installing Rack Cabinets

Installing a rack cabinet may involve:

1

Opening and closing the front rack door

2

Removing and replacing the rack doors

3

Removing and replacing the side panels

4

Installing the brushes

5

Removing and replacing the extension service cover

6

Removing and replacing the extension

7

Reversing the front door

8

Securing the rack leveling feet

9

Installing the rack stabilizer feet

10

Adjusting the rear rack posts

11

Routing cables

12

Coupling two racks

Installation Guide 9

Opening and Closing the Front Rack Door

To open the front rack door:

1

Press in on the handle lock cylinder where the key is inserted. See Figure 1.

2

After the handle is released, pull it upwards to release the door from the

catches. See Figure 1.

3

Open the front door all the way. See Figure 1.

To close the door:

1

Push the door frame evenly against the extension frame and ensure that

the door is in contact with the extension frame.

2

Push the handle down to latch the door.

Removing and Replacing the Rack Doors

WARNING: Never attempt to remove or install the rack cabinet doors by yourself.

Due to the size and weight of the rack cabinet doors, this procedure requires at

least two people.

Removing the Front Door

1

Open the rack door. See "Opening and Closing the Front Rack Door" on

page 9.

2

While holding the door, remove the hinge pins starting from the bottom of the

rack. Ensure that the top hinge pin is the last pin to be removed from the door.

To remove the hinge pin:

a

Pull the hinge pin so that it clears the hinge-pin housing on the door.

For the hinge pins located at the bottom of the door, pull the two

hinge pins downward. For the hinge pins located at the top of the

door, pull the two hinge pins upward. See Figure 1.

The hinge pin's retention clip prevents the hinge from being

completely pulled out of the hinge body.

b

Pull the door slightly away from the rack so that the door clears the

hinge body.

WARNING: When storing the doors, lay the doors flat so they do not fall over

and accidentally injure someone.

WARNING: Due to the size and weight of the door, it is recommended that you lay

the removed door flat with its outer surface facing upward.

3

Lay the door in a safe location with the door's outer surface facing upward

to prevent damage to the door's badge and cosmetic coating.

10 Installation Guide

Figure 1. Removing the Front Door

Replacing the Front Door

To replace the front door, follow the steps for removing the front door in the

reverse order.

1 handle 2 hinge pins (4)

3 hinge body 4 hinge-pin housings (4)

5 lock cylinder

1

3

5

4

2

Installation Guide 11

Removing the Back Doors

WARNING: Never attempt to remove or install the rack cabinet doors by yourself.

Due to the size and weight of the rack cabinet doors, this procedure requires

two people.

1

Rotate the door handle one-quarter turn clockwise to open the back doors.

See Figure 2.

Figure 2. Opening the Back Doors

1 door handle 2 back doors (2)

2

1

12 Installation Guide

2

Remove the right back door.

a

While supporting the door, pull the pin for the top hinge out of the

door’s hinge-pin housing. See Figure 3.

You hear a click sound as you pull the pin out of the door’s hinge-pin

housing. The hinge pins are designed to prevent them from being pulled

out of the hinge body.

b

Repeat step a for the bottom hinge.

c

Pull the door away from the rack.

Figure 3. Removing the Back Doors

WARNING: Due to the size and weight of the door, it is recommended that you lay

the removed door flat with its outer surface facing upward.

1 hinge pin 2 hinge body

3 hinge-pin housing

1

2

3

Installation Guide 13

d

Lay the door in a safe location with the door’s outer surface

facing upward.

NOTE: Lay the door flat with the outer surface facing upward to prevent

damage to its cosmetic coating.

3

Repeat step a through step d for the left back door.

Replacing the Back Doors

To replace the back doors, follow the steps for removing the back doors in the

reverse order.

Removing and Replacing the Side Panels

NOTE: Remove the lower side panels in order to install the side brushes and the

side stabilizer feet.

NOTE: Although removing the side panels is not mandatory for installing

systems in a rack, having the sides open makes it easier to install slide assemblies

and support rails and to reverse the direction that the front door opens.

Removing the Upper Side Panels

1

Push both latches up and swing the bottom end of the panel away

from the rack. See Figure 4.

2

Grasp firmly on each side of the panel.

3

Lift the panel upward until the panel lip clears the top of the rack.

4

Lay the panel in a safe location with the panel’s outer surface facing

upward to prevent damage to its cosmetic coating.

5

Repeat step 1 through step 4 for the other upper side panel.

Replacing the Upper Side Panels

1

Lift the upper side panel up onto the rack, hooking the panel lip over the

top of the rack. See Figure 4.

2

Swing the bottom of the panel downward onto the rack.

3

Press the panel into the rack until both latches lock into place.

14 Installation Guide

Figure 4. Replacing the Upper Side Panels

Removing the Lower Side Panels

1

Pull both latches down and allow the side panel to swing outward

slightly at the top.

2

Firmly grasp both sides of the panel.

3

Lift the panel upward until the panel hooks clear the holes in the

bottom of the rack frame.

4

Place the panel in a safe location with the panel’s outer surface facing

upward to prevent damage to its cosmetic coating.

5

Repeat step 1 through step 4 for the other lower side panel.

1 panel lip 2 upper side panel

3 latches (2)

2

3

1

Installation Guide 15

Replacing the Lower Side Panels

1

Lower the panel into the rack, inserting the panel hook into the back hole

in the bottom of the rack frame and the front hook into the corresponding

hole in the front of the rack frame. See Figure 5.

2

Swing the top end of the panel toward the rack.

3

Press the panel into the rack until both latches lock into place.

Figure 5. Replacing the Lower Side Panels

1 panel hooks (2) 2 latches (2)

3 lower side panel

1

2

3

16 Installation Guide

Installing the Brushes

WARNING: All brushes supplied must be installed and the brush bristles must be

in contact with the floor to form a seal around the bottom perimeter of the rack

enclosure. Removing the brushes may reduce the cooling efficiency within the

enclosure.

To install the brushes on the side of the rack:

1

Remove the lower side panel. See "Removing the Lower Side Panels" on

page 14.

2

Align the brush bracket with the rack frame and insert the brush bracket

into the rack frame. See Figure 6.

3

Secure the brush bracket using the four bolts and washers. See Figure 6.

4

Replace the lower side panel. See "Replacing the Lower Side Panels" on

page 15.

5

Repeat step 1 through step 4 for the other side of the rack.

To install the brush at the back of the rack:

1

Rotate the door handle one-quarter turn clockwise to open the back doors.

See Figure 2.

2

Align the brush bracket with the rack frame and insert the brush bracket

into the rack frame. See Figure 6.

3

Secure the brush bracket using the two bolts and washers. See Figure 6.

4

Close the back door.

Installation Guide 17

Figure 6. Installing and Removing the Brushes

1 side brush brackets (2) 2 rack frame

3 back brush bracket 4 bolts and washers

4

1

2

3

18 Installation Guide

Removing and Replacing the Extension Service Cover

WARNING: The extension service cover must only be removed when installing or

removing components from the upper rack unit spaces and must be reinstalled

immediately. Components in the rack may overheat if the extension service cover

is not installed in the rack enclosure.

NOTE: Do not use the extension service cover as an outlet to route cables out of

the rack.

NOTE: Removing the extension service cover allows you to install and service the

equipment in the upper rack unit spaces more easily.

Removing the Extension Service Cover

1

Loosen and remove the four wing nuts located on the top surface inside of

the extension. See Figure 7.

2

Lift the extension service cover until the studs clear the holes in the extension.

3

Remove the extension service cover.

ページを読み込んでいます...

Dell Energy Smart Rack Enclosure, PowerEdge 4220, PowerEdge PDU Managed LED, PowerEdge PDU Metered LCD, PowerEdge Rack Enclosure 4020S, PowerEdge Rack Enclosure 4620S クイックスタートガイド

関連論文