Sony DSC-H55 取扱説明書

GB

CT

CS

4-172-685-12(1)

DSC-H55

GB Digital Still Camera/Instruction Manual

CT

CS

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call upon your Sony dealer

regarding this product.

Model No. DSC-H55

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

IMPORTANT SAFETY INSTRUCTIONS

-SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

• Do not handle damaged or leaking lithium ion batteries.

English

WARNING

CAUTION

GB

3

GB

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ Battery charger

Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC

power source (mains) as long as it is connected to the wall outlet (wall socket). If some

trouble occurs while using the battery charger, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

For Customers in the U.S.A. and Canada

GB

4

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669)

The number below is for the FCC related matters only.

[ Regulatory Information

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

For Customers in the U.S.A.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-H55

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

GB

5

GB

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

For Customers in Europe

GB

6

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

GB

7

GB

Table of contents

Getting started

Refer to “Cyber-shot Handbook” (PDF) on supplied

CD-ROM ..............................................................................8

Checking the accessories supplied ....................................8

Notes on using the camera..................................................8

Identifying parts .................................................................11

Charging the battery pack.................................................12

Inserting the battery pack/a memory card (sold

separately) .........................................................................14

Setting the clock ................................................................17

Shooting/viewing images

Shooting still images..........................................................18

Shooting movies ................................................................19

Viewing images..................................................................20

“Cyber-shot Handbook” (PDF)

Learning more about the camera (“Cyber-shot

Handbook”)........................................................................21

Others

List of icons displayed on the screen ................................22

Number of still images and recordable time of movies .....24

Precautions ........................................................................25

Specifications ....................................................................27

GB

8

Checking the accessories supplied

• Battery charger BC-CSGD/BC-CSGE (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Rechargeable battery pack NP-BG1 (1)/Battery case (1)

• USB, A/V cable for multi-use terminal (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot Handbook”

• Instruction Manual (this manual) (1)

Notes on using the camera

Changing the language setting

The screen language setting, press the MENU button, then select

(Settings) t (Main Settings) t [Language Setting].

Internal memory and memory card back up

Do not turn off the camera, remove the battery pack, or remove the memory

card while the access lamp is lit. Otherwise, the internal memory data or the

memory card may be damaged. Be sure to make a backup copy to protect your

data.

On database files

When you insert a memory card without a database file into the camera and

turn on the power, part of the memory card capacity is used to automatically

create a database file. It may take some time until you can perform the next

operation.

Refer to “Cyber-shot Handbook” (PDF)

on supplied CD-ROM

For details on advanced operations, please read “Cyber-

shot Handbook” (PDF) on the CD-ROM (supplied) using

a computer.

Refer to “Cyber-shot Handbook” for in-depth instructions

on shooting or viewing images and connecting the camera to your

computer, printer or TV (page 21).

GB

9

GB

Notes on recording/playback

• When you use a memory card with this camera for the first time, it is

recommended to format the card using the camera for stable performance of

the memory card before shooting. Note that formatting permanently erases

all data on the memory card, and is unrecoverable. Save precious data on a

computer, etc.

• Before you start recording, make a trial recording to make sure that the

camera is working correctly.

• The camera is neither dust-proof, nor splash-proof, nor water-proof. Read

“Precautions” (page 25) before operating the camera.

• Avoid exposing the camera to water. If water enters inside the camera, a

malfunction may occur. In some cases, the camera cannot be repaired.

• Do not aim the camera at the sun or other bright light. It may cause the

malfunction of the camera.

• Do not use the camera near a location that generates strong radio waves or

emits radiation. Otherwise, the camera may not properly record or play back

images.

• Using the camera in sandy or dusty locations may cause malfunctions.

• If moisture condensation occurs, remove it before using the camera.

• Do not shake or strike the camera. It may cause a malfunction and you may

not be able to record images. Furthermore, the recording media may become

unusable or image data may be damaged.

• Clean the flash surface before use. The heat of flash emission may cause dirt

on the flash surface to become discolored or to stick to the flash surface,

resulting in insufficient light emission.

Notes on the LCD screen and lens

• The LCD screen is manufactured using extremely high-precision technology

so over 99.99% of the pixels are operational for effective use. However,

some tiny black and/or bright dots (white, red, blue or green) may appear on

the LCD screen. These dots are a normal result of the manufacturing process,

and do not affect the recording.

• When the battery level becomes low, the lens might stop moving. Insert a

charged battery pack and turn on the camera again.

On camera’s temperature

Your camera and battery may get warm due to continuous use, but it is not a

malfunction.

GB

10

On the overheat protection

Depending on the camera and battery temperature, you may be unable to

record movies or the power may turn off automatically to protect the camera.

A message will be displayed on the LCD screen before the power turns off or

you can no longer record movies.

On image data compatibility

• The camera conforms with DCF (Design rule for Camera File system)

universal standard established by JEITA (Japan Electronics and Information

Technology Industries Association).

• Sony does not guarantee that the camera will play back images recorded or

edited with other equipment, or that other equipment will play back images

recorded with the camera.

Warning on copyright

Television programs, films, videotapes, and other materials may be

copyrighted. Unauthorized recording of such materials may be contrary to the

provisions of the copyright laws.

No compensation for damaged content or recording failure

Sony cannot compensate for failure to record or loss or damage of recorded

content due to a malfunction of the camera or recording media, etc.

GB

11

GB

Identifying parts

A Shutter button

B Mode dial

C For shooting: W/T (Zoom) lever

For viewing: (Playback

zoom) lever/ (Index) lever

D Flash

E ON/OFF (Power) button

F Microphone

G Self-timer lamp/Smile Shutter

lamp/AF illuminator

H Lens

I LCD screen

J Hook for wrist strap

K (Playback) button

L Control button

Menu on: v/V/b/B/z

Menu off: DISP/ / /

M (Delete) button

N MENU button

O Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

P Speaker

Q Multi connector

R Battery/memory card cover

S Access lamp

T Battery insertion slot

U Battery eject lever

V Memory card slot

GB

12

Charging the battery pack

1

Insert the battery pack into the

battery charger.

• You can charge the battery even when it is

partially charged.

2

Connect the battery

charger to the wall

outlet (wall socket).

If you continue charging the

battery pack for about one

more hour after the

CHARGE lamp turns off,

the charge will last slightly

longer (full charge).

CHARGE lamp

Lit: Charging

Off: Charging finished

(normal charge)

3

When charging is finished, disconnect the battery

charger.

Battery

pack

Plug

For customers in the USA and Canada

CHARGE lamp

Power cord

(Mains lead)

For customers in countries/regions

other than the USA and Canada

GB

13

GB

x

Charging time

• The table above shows the time required to charge a fully depleted battery pack at

a temperature of 25 °C (77 °F). Charging may take longer depending on

conditions of use and circumstances.

• Connect the battery charger to the nearest wall outlet (wall socket).

• When charging is finished, disconnect the power cord (mains lead) from the wall

outlet (wall socket), and remove the battery pack from the battery charger.

• Be sure to use the battery pack or the battery charger of the genuine Sony brand.

x

Battery life and number of still images you can

record/view

• The number of still images that can be recorded is based on the CIPA standard,

and is for shooting under the following conditions.

(CIPA: Camera & Imaging Products Association)

– DISP (Screen Display Settings) is set to [Normal].

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

– A fully charged battery pack (supplied) is used at an ambient temperature of

25 °C (77 °F).

– Using Sony “Memory Stick PRO Duo” media (sold separately).

Full charge time Normal charge time

Approx. 330 min. Approx. 270 min.

Notes

Battery life (min.) No. of Images

Recording Approx. 155 Approx. 310

Viewing Approx. 370 Approx. 7400

Note

z Using the camera abroad

You can use the camera and the battery charger (supplied) in any country or

region where the power supply is within 100 V to 240 V AC, 50/60 Hz.

Do not use an electronic transformer (travel converter). This may cause a

malfunction.

GB

14

Inserting the battery pack/a memory card

(sold separately)

1

Open the cover.

2

Insert the memory card

(sold separately).

With the notched corner facing as

illustrated, insert the memory card

until it clicks into place.

3

Insert the battery pack.

Check the direction of the battery,

insert the battery pack while

pressing the battery eject lever in

the direction of the arrow. Insert the

battery until the battery eject lever

is locked.

4

Close the cover.

Closing the cover with the battery

inserted incorrectly may damage

the camera.

Ensure the notched

corner faces correctly.

GB

15

GB

x

Memory cards that you can use

• The following memory cards are compatible with this camera: “Memory

Stick PRO Duo” media, “Memory Stick PRO-HG Duo” media, “Memory

Stick Duo” media, SD memory cards, SDHC memory cards and SDXC

memory cards. Operation with all memory cards is not assured.

MultiMediaCard is not compatible.

Images recorded on SDXC memory cards cannot be played back or captured

on non-exFAT-compatible computers, AV components, etc., connected to

this camera by USB cable. Check that the connected devices are compatible

with exFAT beforehand. If you connect a device that is not compatible with

exFAT, the screen for initialization may appear. Never execute initialization

otherwise all recorded contents will be lost.

(exFAT is the file system used in SDXC memory cards.)

• In this manual, “Memory Stick PRO Duo” media, “Memory Stick PRO-HG

Duo” media and “Memory Stick Duo” media are called “Memory Stick

Duo” media and SD memory cards, SDHC memory cards and SDXC

memory cards are called SD memory cards.

• When recording movies, it is recommended that you use the following

memory cards:

– (Mark2) (“Memory Stick PRO Duo” (Mark2)

media)

– (“Memory Stick PRO-HG Duo” media)

– SD memory card, SDHC memory card or SDXC memory card (Class 4 or

faster)

For details on the number of images/time that can be recorded, see page 24.

x

To remove the memory card

• Never remove the memory card/battery pack when the access lamp is lit. This may

cause damage to data in the memory card/internal memory.

Make sure that the access lamp is not lit,

then push the memory card in once.

Note

Access lamp

GB

16

x

When there is no memory card inserted

Images are stored in the camera’s internal memory (approximately 45 MB).

To copy images from the internal memory to a memory card, insert the

memory card in the camera, then select MENU t (Settings) t

(Memory Card Tool) t [Copy].

x

To remove the battery pack

x

Checking the remaining battery charge

A remaining charge indicator appears on the LCD screen.

• It takes about one minute until the correct remaining charge indicator appears.

• The remaining charge indicator may not be correct under certain circumstances.

• When [Power Save] is set to [Stamina] or [Standard], if you do not operate the

camera running on a battery pack for a certain amount of time, the brightness level

on the LCD screen becomes dark, and then the camera automatically turns off to

prevent wearing down the battery pack (Auto Power off).

• To prevent terminal contamination, or short-circuiting with metallic objects, etc.,

always carry or store the battery in the supplied case.

Slide the battery eject lever. Be sure not

to drop the battery pack.

Notes

Battery eject lever

High

Low

GB

17

GB

Setting the clock

x

Setting the date and time again

Press the MENU button, then select (Settings) t (Clock Settings).

1

Press the ON/OFF (Power)

button.

The camera is turned on.

• It may take time for the power to

turn on and allow operation.

2

Select a setting item with

v/V on the control button,

then press z.

Date & Time Format: Selects the

date and time display format.

Daylight Savings: Selects

Daylight Savings On/Off.

Date & Time: Sets the date and

time.

3

Set the numeric value and desired settings with v/V/

b/B, then press z.

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

4

Follow the instructions on the screen. Select your

desired area with b/B on the control button, then

press z.

5

Select [OK], then press z.

ON/OFF (Power) button

Control button

GB

18

Shooting still images

1

Set the mode dial to

(Intelligent Auto

Adjustment), then press

the ON/OFF (Power)

button.

2

Hold the camera steady as

illustrated.

• Turn the W/T (zoom) lever to (T) to zoom

in, and to (W) to zoom out.

3

Press the shutter button

halfway down to focus.

When the image is in focus, a beep

sounds and the z indicator lights.

4

Press the shutter button fully

down.

Mode dial

ON/OFF (Power) button

Shutter

button

AE/AF

lock

GB

19

GB

Shooting movies

• The operating sound of the lens is recorded when the zoom function operates

while shooting a movie.

1

Set the mode dial to

(Movie Mode), then

press the ON/OFF

(Power) button.

2

Press the shutter button fully

down to start recording.

3

Press the shutter button fully down again to stop

recording.

Note

Mode dial

ON/OFF (Power) button

GB

20

Viewing images

x

Returning to shooting images

Press the shutter button halfway down.

x

Turning off the camera

Press the ON/OFF (Power) button.

1

Press the (Playback)

button.

• When images on a memory card

recorded with other cameras are

played back on this camera, the

registration screen for the data file

appears.

x

Selecting next/previous

image

Select an image with B (next)/b

(previous) on the control button.

• Press z in the center of the control

button to view movies.

x

Deleting an image

1 Press (Delete) button.

2 Select [This Image] with v on the

control button, then press z.

(Playback) button

(Delete)

button

Control button

ページが読み込まれています...

Sony DSC-H55 取扱説明書

Sony DSC-H55 取扱説明書

他の言語で

関連論文