ExpertResults
7000
1
2
11
4
3
5
6
7
8
9
10
empty page before TOC
English
6English
Introduction
Congratulations on your new Philips Sonicare power
toothbrush! Superior plaque removal, whiter teeth and
healthier gums are at your fingertips. Using Sonicare’s
combination of gentle sonic technology and clinically
developed and proven features, you can be confident
that you’re getting the very best clean, every time.
Further support and product registration are available to
you at: www.philips.com/welcome.
Welcome to the Philips Sonicare family!
Intended use
ExpertResults series power toothbrushes are intended to
remove adherent plaque and food debris from the teeth
to reduce tooth decay and improve and maintain oral
health. ExpertResults series power toothbrushes are
intended for consumer home use. Use by children should
be with adult supervision.
Important safety information
Read this important information carefully before you use
the appliance and save it for future reference.
Note: The accessories and features of different models
vary. For example, some models come with a sanitizer or
are equipped with Bluetooth.
Danger
- Keep the charger and/or sanitizer away from water.
Do not place or store the appliance where it can fall or
be pulled into a tub or sink.
- Do not immerse the charger and/or sanitizer in water
or any other liquid.
- After cleaning, make sure the charger and/or sanitizer
is completely dry before you connect it to the wall
socket.
7
English
Warning
- This appliance can be used by children and persons
with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning use
of the appliance in a safe way and understand the
hazards involved. Cleaning and user maintenance
shall not be made by children without supervision.
- Children shall not play with the appliance.
- Keep the sanitizer out of the reach of children at all
times.
- Stop using the sanitizer if the UV light bulb remains
on when the door is open. UV light can be harmful to
the human eye and skin.
- If the appliance is damaged in any way (brush head,
toothbrush handle, charger and/or sanitizer), stop
using it.
- The mains cord cannot be replaced. If the mains cord
is damaged, discard the charger and/or sanitizer.
- Always replace the charger and/or sanitizer with one
of the original type in order to avoid a hazard.
- This appliance contains no user-serviceable parts. If
the appliance is damaged, contact the Consumer Care
Center in your country (see 'Warranty and support').
- Keep the cord away from heated surfaces.
- Do not use the charger and/or sanitizer outdoors or
near heated surfaces.
Caution
- Do not clean the brush head, handle, charger, charger
cover or sanitizer in the dishwasher.
- If you have had oral or gum surgery in the previous 2
months, consult your dentist before you use this
appliance.
- Consult your dentist if excessive bleeding occurs after
using this appliance or if bleeding continues to occur
after 1 week of use. Also consult your dentist if you
experience discomfort or pain when you use this
appliance.
8English
- This Philips appliance complies with the safety
standards for electromagnetic devices. If you have a
pacemaker or other implanted device, contact your
doctor or the appliance manufacturer of the
implanted appliance prior to use.
- If you have medical concerns, consult your doctor
before you use this appliance.
- This appliance has only been designed for cleaning
teeth, gums and tongue. Do not use it for any other
purpose. Stop using the appliance and contact your
doctor if you experience any discomfort or pain.
- This appliance is a personal care device and is not
intended for use on multiple patients in a dental
practice or institution.
- Do not use other brush heads than the ones
recommended by Philips Sonicare.
- Stop using a brush head with crushed or bent bristles.
Replace the brush head every 3 months or sooner if
signs of wear appear.
- If your toothpaste contains peroxide, baking soda or
bicarbonate (common in whitening toothpastes),
thoroughly clean the brush head with soap and water
after each use. This prevents possible cracking of the
plastic.
- Avoid direct contact with products that contain
essential oils or coconut oil. Contact may result in
bristles dislodging.
- The UV light bulb of the sanitizer is hot during and
immediately after the sanitizing cycle. Do not touch
the UV light bulb when it is hot.
- Do not operate the sanitizer without the protective
screen in place to avoid contact with a hot UV light
bulb.
- If you have used the sanitizer for 3 UV clean cycles in a
row, switch it off for at least 30 minutes before you
start another UV clean cycle.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
9
English
Radio Equipment Directive
Hereby, Philips declares that electric toothbrushes with
radio frequency interface (Bluetooth) are in compliance
with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
www.philips.com/support
The radio frequency interface in this product operates at
13.56MHz.
The maximum RF power transmitted by the appliance is
30.16dBm.
Your Philips Sonicare (Fig. 1)
1 Hygienic travel cap
2 Smart brush head(s)*
3 Handle
4 Power on/off button
5 Intensity light
6 Mode/intensity button
7 Modes
8 Brush head replacement reminder light
9 Battery indication
10 Charger
11 Travel case
*Note: The content of the box may vary based on the
model purchased.
Using your Philips Sonicare
Brushing instructions
1Push the brush head firmly onto the handle.
Note: It is normal to see a slight gap between the
brush head and the handle.
2Wet the bristles and apply toothpaste.
3Place the toothbrush bristles against the teeth at a
slight angle (45 degrees), pressing firmly to make the
bristles reach the gumline or slightly beneath the
gumline.
10 English
45°
Note: Keep the center of the brush in contact with the
teeth at all times.
4Press the power on/off button to turn on the Philips
Sonicare.
5Apply light pressure to maximize Philips Sonicare’s
effectiveness and let the Philips Sonicare toothbrush
do the brushing for you. Gently move the brush head
slowly across the teeth in a small back and forth
motion so the longer bristles reach between your
teeth. Continue this motion throughout the brushing
cycle.
Note: To learn how to brush with specific modes, see
‘Modes’.
Note: The bristles should slightly flare. Do not scrub.
Note: A change in vibration from the handle alerts
you when you apply too much pressure while
brushing.
Note: Your handle will briefly pause its vibration when
its time to brush the next section, see 'QuadPacer'.
6To clean the inside surfaces of the front teeth, tilt the
brush handle semi-upright and make several vertical
overlapping brushing strokes on each tooth.
Your Philips Sonicare toothbrush is safe to use on:
- Braces (brush heads wear out sooner when used on
braces)
- Dental restorations (fillings, crowns, veneers)
Brush heads
Your brush heads
To see what type of brush head you have, check the
brush head label at the bottom.
11
English
W
C
3
Brush head name DiamondClean Premium Plaque Control
Brush head label W C3
Benefit Stain removal Plaque removal
To explore our full range of brush heads, go to
www.philips.com/toothbrush-heads for more
information.
BrushSync Technology
BrushSync technology enables your brush heads to
communicate with your handle using a microchip. The
symbol at the bottom of the brush head indicates that it
is equipped with the BrushSync technology.
This enables the following features:
- Brush head mode pairing
- Brush head replacement reminder
Brushing modes
Your power toothbrush is equipped with 3 different
modes: Clean, White, and Gum Care. Based on the smart
brush head you use, the mode will be selected
automatically. To manually change the mode, press the
mode/intensity button while the toothbrush is off.
12 English
Clean White Gum Care
Benefit Plaque removal Plaque and
surface stains
removal
Plaque removal
and gum
massage
Re-
commended
brush head
Premium Plaque
Control (C3)
Diamond Clean
(W)
Optimal Gum
Care (G2)
Re-
commended
intensity level
3 3 3
Total brushing
time
2 minutes 2 minutes and 30
seconds
3 minutes
How to brush Brush each
quadrant for 30
seconds
2
4
3
1
Brush each
quadrant for 30
seconds,
2
4
3
1
then brush the
front top and
bottom teeth for
an additional 30
seconds.
1
2
Brush each
quadrant for 30
seconds,
2
4
3
1
then brush along
the gumline for
an additional
minute.
Note: After you have completed the brushing cycle, you
can spend additional time brushing the chewing surfaces
of your teeth and areas where staining occurs. You can
13
English
also brush your tongue, with the toothbrush turned on or
off, as you prefer.
Note: All brush heads work with each mode.
Note: When the Philips Sonicare is used in clinical studies,
it must be used in the Clean mode (for plaque and gum
claims) or in White mode (for whitening claims), at high
intensity, with the EasyStart feature turned off.
Intensity settings
Your power toothbrush comes with 3 different intensity
levels: low, medium and high. When attached to the
handle, the smart brush head will automatically select the
recommended intensity. To manually change the
intensity, turn on the handle and press the
mode/intensity button.
Features
- EasyStart
- Brush head replacement reminder
- Pressure sensor
- Brush head mode pairing
- QuadPacer
EasyStart
The EasyStart feature gently increases the power of the
handle over the first 14 brushings to help you get used to
the brushing power of the Philips Sonicare.
The EasyStart feature works with all modes.
Note: The EasyStart feature comes deactivated with your
product. To activate EasyStart, see 'Activating or
deactivating features'.
Brush head replacement reminder
The handle will track the wear of your brush head. It
measures:
- The pressure you apply when you brush
- The time you have brushed with the brush head
14 English
Once your brush head is no longer effective, the brush
head replacement reminder will blink amber. This
indicates that it is recommended to change your brush
head.
Note: The brush head replacement reminder comes
activated with your product. To deactivate this feature,
see 'Activating or deactivating features'.
Pressure sensor
Your Philips Sonicare measures the pressure you apply
while brushing to protect your gums and teeth from
damage.
If you apply too much pressure, the handle will change its
vibration until you reduce the pressure.
Note: The pressure sensor comes activated with your
product. To deactivate this feature, see 'Activating or
deactivating features'.
Brush head mode pairing
Brush heads with BrushSync technology are equipped
with an RFID chip. The chip communicates to the handle
and automatically pairs it with the recommended mode
and intensity.
Note: If you change modes/intensity, the handle will
remember the last used setting. If you wish to brush with
the recommended setting, you can find the
recommended modes/intensity in ‘Brushing Modes’.
QuadPacer
The QuadPacer feature indicates via a brief change in
vibration when you are supposed to move onto the next
brushing section.
The toothbrush will automatically turn off at the end of
the brushing session.
Charging and battery status
Charging
1Plug the charger into an electrical outlet.
2Place the handle on the charger.
3The charging indicator will flash green until your
toothbrush is fully charged.
15
English
Battery status (handle on plugged-in charger)
LED color Battery charging status
Flashing green Charging
Solid green Fully charged
Off Fully charged and in sleep mode
When placing the handle on the charger:
- The handle will emit 2 short beeps to confirm the
handle is placed properly and the handle starts
charging.
- The battery light will flash green to indicate it is
charging.
- The handle will show solid green when it is fully
charged. In order to preserve the charge, the green
light will switch off 30 seconds after the charging
process is complete.
Battery status (when handle is not placed on
charger)
When removing the handle from the charger, the battery
light at the bottom of the handle will indicate the status
of the battery.
LED color Number of beeps Status
Solid green n/a Full
Flashing green n/a Medium
Flashing amber 3 Low
Flashing amber 5 Battery empty
Note: Your toothbrush comes pre-charged for first use.
After first use, charge for at least 24 hours.
Note: It is OK to leave the handle on the plugged in
charger in between brushings. This will not impact the
battery life negatively.
16 English
Activating or deactivating features
You can activate or deactivate the following features of
your toothbrush:
- EasyStart
- Brush head replacement reminder
- Pressure sensor
1Place the handle on the charger.
2Press and hold the power button for:
Feature Press the power button for
EasyStart 3 seconds
Brush head replacement reminder Up to 5 seconds
Pressure sensor Up to 7 seconds
3Let go of the power button when you hear:
Feature You will hear
EasyStart 1 beep
Brush head replacement reminder 1 beep then 2 beeps
Pressure sensor 1 beep, 2 beeps then 3 beeps
If you see the brush head replacement reminder and the
battery indicator lights flashing green and hear low to
high triple tones, then the feature had been activated.
OR
If you see the brush head replacement reminder and the
battery indicator lights flashing amber and hear high to
low triple tones, then the feature had been
deactivated.
17
English
Cleaning
Caution: Unplug the charger before you clean it.
Caution: Do not use essential oils to clean the brush
heads as this can cause damage.
Caution: Do not use isopropyl rubbing alcohol,
vinegar or bleach to clean the handle as this may
cause discoloration.
Caution: Do not push on the rubber seal at the top of
the handle.
Locating the model number
Look on the bottom of the Philips Sonicare toothbrush
handle for the model number (HX751x).
18 English
Frequently asked questions
Question Answer
Is my Philips Sonicare toothbrush
water resistant?
Yes. However, do not fully submerge
the handle in liquid for an extended
period of time.
How often should I clean the
connection between the brush head
and the handle?
It is recommended to clean this after
each brushing, or at least once a
week.
Can I leave my Philips Sonicare
toothbrush on the charger between
brushings?
Yes, you can always keep your Philips
Sonicare toothbrush on a plugged-in
charger. This will not affect the
battery lifetime.
How often can I use my Philips
Sonicare toothbrush per charge?
Your Philips Sonicare toothbrush
should last 2-3 weeks with standard
brushings (2x/day) with a full battery.
You do not have to charge your
Philips Sonicare toothbrush on a daily
basis.
Recycling
- Do not throw away the product with the normal
household waste at the end of its life, but hand it in at
an official collection point for recycling. By doing this,
you help to preserve the environment.
- This product contains a built-in rechargeable battery
which shall not be disposed of with normal household
waste. Please take your product to an official
collection point or a Philips service center to have a
professional remove the rechargeable battery.
- The UV light bulb of the sanitizer contains mercury.
Do not throw the UV light bulb away with the normal
household waste at the end of its life. Hand it in at an
official collection point for recycling.
19
English
- Follow your country’s rules for the separate collection
of electrical and electronic products and rechargeable
batteries. Correct disposal helps prevent negative
consequences for the environment and human
health.
Removing the rechargeable battery at the end of
lifetime
Warning: Only remove the rechargeable battery
when you discard the appliance. Make sure the
battery is completely empty when you remove it.
Any attempt to remove the battery will void the
warranty.
To remove the rechargeable battery, you need a towel or
cloth, a hammer and a flat-head (standard) screwdriver.
Observe basic safety precautions when you follow the
procedure outlined below. Be sure to protect your eyes,
hands, fingers, and the surface on which you work.
1Remove and discard the brush head.
2Deplete the battery until the handle no longer turns
on.
3Cover the entire handle with a towel or cloth.
1
2
4Hold the top of the handle with one hand.
5With your other hand, use your hammer to strike the
handle 0.5 inches above the bottom end on all sides
to eject the end cap.
Note: You may have to strike it several times to break
the internal cap connections.
20 English
6Remove the end cap. If the end cap does not release
easily, repeat step 3 until the end cap is released.
7Holding the handle upside down with a cloth or
towel, push the handle down on a hard surface. If the
internal components do not easily release from the
housing, repeat step 3 until the internal components
are released.
8Remove the rubber battery cover with a screwdriver.
9Wedge the screwdriver between the battery and the
internal black frame towards the bottom to separate
them.
10 Insert the screwdriver between the bottom of the
battery and the black frame to break the metal tab
connecting the battery to the green printed circuit
board. This will release the bottom end of the battery
from the frame.
11 Grab the battery and pull it away from the internal
components to break the second metal battery tab.
Caution: Be aware of the sharp edges of the
battery tabs so as to avoid injury to your fingers.
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/