Philips AT798/16 ユーザーマニュアル

AT798

User manual / 用户手册

Question?

有疑问?

Contact Philips

请联系飞利浦

User manual / 用户手册

1

AT798

ENGLISH 6

简体中文 21

6

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at www.philips.com/

welcome.

Please read this user manual, as it contains

information about the wonderful features of this

shaver as well as some tips to make shaving easier

and more enjoyable.

General description (Fig. 1)

1 Protection cap

2 Shaving unit

3 Shaving unit release button

4 Shaver on/off button

5 Shaving head symbol

6 Charging light

7 Charging stand

8 Adapter

9 Cleaning brush

10 Trimmer release slide

11 Trimmer

Important

Read this user manual carefully before you use the

shaver and the charging stand.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug,

as this causes a hazardous situation.

ENGLISH

- This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

these appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not

be made by children unless they are older than

8 and supervised.

- Always unplug the shaver before you clean it

under the tap.

Caution

- Never immerse the charging stand in water nor

rinse it under the tap.

- Never use water hotter than 80°C to rinse the shaver.

- Do not use the shaver, adapter, charging stand or

any other part if it is damaged, as this may cause

injury. Always replace a damaged adapter, charging

stand or part with one of the original type.

- Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol

or acetone to clean the appliance.

- Water may leak from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Compliance with standards

- This shaver is waterproof and complies with the

internationally approved safety regulations. It is

suitable for use in the bath or shower and for

cleaning under the tap. For safety reasons, the

shaver can therefore only be used cordlessly.

- The shaver complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

ENGLISH 7

General

- The adapter is equipped with an automatic

voltage selector and is suitable for mains voltages

ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

Charging

Note: The shaver cannot be used directly from the mains.

When you charge the shaver for the rst time or

after a long period of disuse, let it charge until the

charging light lights up continuously.

See the table below for the charging time of your shaver.

It takes approximately 8 hours to fully charge the shaver.

A fully charged shaver provides up to 40 minutes of

cordless shaving. The shaving time may be less than

40 minutes as a result of your shaving behaviour,

your cleanings habits or your beard type.

Charge indications

Battery low

- When the battery is almost empty (when there

are only 5 or fewer shaving minutes left), the

charging light starts to ash orange. When you

switch off the shaver, the charging light continues

to ash orange for a few seconds.

ENGLISH8

Charging

- When the shaver is charging, the charging light

ashes green.

Battery fully charged

- When the battery is fully charged, the charging

light lights up green continuously.

Note: After approx. 30 minutes, the charging light goes

out to save energy.

Charging

1 Put the small plug in the shaver.

2 Put the adapter in the wall socket.

, The charging light shows the charging status

of the shaver (see section ‘Charge indications’

in this chapter).

Charging in the charging stand

1 Put the small plug in the charging stand.

2 Put the adapter in the wall socket.

3 Place the shaver in the charging stand.

, The charging light shows the charging status

of the shaver (see section ‘Charge indications’

in this chapter).

ENGLISH 9

Using the shaver

Note: This shaver can be used in the bath or shower.

It can therefore not be used directly from the mains

for safety reasons.

Shaving tips and tricks

- This shaver is suitable for both wet and dry use.

Use the shaver with shaving gel or foam for extra

skin comfort, or use the shaver dry for extra

convenience.

Note: We advise you to use the shaver with shaving gel

or foam when you use it for a wet shave. Do not use

thick shaving cream or shaving oil with this shaver.

- For optimal shaving results, make circular

movements during use.

- The shaver is waterproof and can be used in the

bath or shower.

- Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

Wet shaving

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over

your skin.

4 Press the on/off button once to switch on

the shaver.

ENGLISH10

5 Move the shaving heads in circular movements

over your skin.

Note: Rinse the shaver under the tap regularly to ensure

that it continues to glide smoothly over your skin.

6 After shaving, press the on/off button once to

switch off the shaver and dry your face.

7 Clean the shaver (see chapter ‘Cleaning and

maintenance’).

Note: Make sure you rinse all foam or shaving gel off

the shaver.

Dry shaving

1 Press the on/off button once to switch on the

shaver.

2 Move the shaving heads in circular movements

over your skin.

3 After shaving, press the on/off button once to

switch off the shaver.

4 Clean the shaver (see chapter ‘Cleaning and

maintenance’).

Trimming

You can use the trimmer to groom your sideburns

and moustache.

1 Push the trimmer slide downwards to open

the trimmer.

2 Press the on/off button once to switch on

the shaver.

, You can now start trimming.

3 After trimming, press the on/off button once to

switch off the shaver.

ENGLISH 11

4 Clean the trimmer (see chapter ‘Cleaning and

maintenance’).

5 Close the trimmer (‘click’).

Cleaning and maintenance

Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol or

acetone to clean the shaver and the charging stand.

Always unplug the shaver before you clean it under

the tap.

- Clean the shaver after every shave for optimal

shaving performance.

- Regular cleaning guarantees better shaving

performance.

- For the best cleaning results, we advise you to use

the Philips Cleaning spray (HQ110).

- Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

Note: Water may leak from the socket at the bottom

of the shaver when you rinse it. This is normal and not

dangerous because all electronics are enclosed in a

sealed power unit inside the shaver.

ENGLISH12

Cleaning the shaving unit under the tap

1 Switch off the shaver.

2 Press the release button to open the shaving

unit.

3 Rinse the shaving unit and hair chamber under

a hot tap for 30 seconds.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

- Rinse the hair chamber and the inside of the

shaving unit.

- Rinse the outside of the shaving unit.

4 Close the shaving unit and shake off excess

water.

Be careful not to hit the shaving unit against

anything while shaking off excess water.

Never dry the shaving unit and the hair chamber

with a towel or tissue, as this may damage the

shaving unit.

5 Open the shaving unit again and leave it open

to let the shaver dry completely.

ENGLISH 13

Cleaning the shaving unit with the

cleaning brush

1 Switch off the shaver.

2 Press the release button to open the shaving

unit.

3 Pull the shaving unit off the shaver.

4 Turn the lock anticlockwise (A) and remove

the retaining frame (B).

5 Remove and clean one shaving head at a time.

Each shaving head consists of a cutter and a

guard.

Note: Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it may take

several weeks before optimal shaving performance is

restored.

- Remove the cutter from the shaving guard and

clean it with the brush.

- Clean the inside and outside of the shaving guard

with the brush.

ENGLISH14

6 Put the shaving heads back into the shaving

unit.

Make sure that the projections of the shaving

heads t exactly into the recesses.

7 Put the retaining frame back into the shaving

unit (A) and turn the lock clockwise (B).

8 Insert the lug of the shaving unit into the slot

in the top of the shaver. Then close the shaving

unit.

Note: If the shaving unit does not close smoothly, check

if you have inserted the shaving heads properly and if

the retaining frame is locked.

ENGLISH 15

Cleaning the trimmer with the cleaning brush

Clean the trimmer every time you have used it.

1 Switch off the shaver.

2 Push the trimmer slide downwards to open

the trimmer.

3 Clean the trimmer with the short-bristled side

of the cleaning brush. Brush up and down along

the trimmer teeth.

4 Close the trimmer (‘click’).

Tip: For optimal trimming performance, lubricate the

trimmer teeth with a drop of sewing machine oil every

six months.

Storage

- Put the protection cap on the shaver to prevent

damage.

ENGLISH16

Replacement

For maximum shaving performance, we advise you

to replace the shaving heads every two years.

Replacement reminder

The shaving head symbol will light up to indicate

that the shaving heads need to be replaced. Replace

damaged shaving heads right away.

Only replace the shaving heads with original HQ8

Philips Shaving Heads.

1 The shaving head symbol lights up orange

continuously.

2 Switch off the shaver. Disconnect the shaver

from the mains or remove it from the charging

stand.

3 Press the release button to open the shaving

unit.

4 Pull the shaving unit off the shaver.

5 Turn the lock anticlockwise (A) and remove

the retaining frame (B).

6 Remove the shaving heads and place new ones

in the shaving unit.

Make sure that the projections of the shaving

heads t exactly into the recesses.

ENGLISH 17

7 Put the retaining frame back into the shaving

unit (A)and turn the lock clockwise (B).

8 Insert the lug of the shaving unit into the slot

in the top of the shaver. Then close the shaving

unit.

Note: If the shaving unit does not close smoothly, check

if you have inserted the shaving heads properly and if

the retaining frame is locked.

9 Press and hold the on/off button for 5 seconds

to reset the replacement reminder on the

shaver. The orange light will go out.

Ordering accessories

To buy accessories or spare parts, visit

www.shop.philips.com/service or go to your

Philips dealer. You can also contact the Philips

Consumer Care Centre in your country (see the

worldwide guarantee leaet for contact details).

To retain the top performance of your shaver, make

sure you clean it regularly and replace its shaving

heads at the recommended time.

Shaving heads

- We advise you to replace your shaving heads

every two years. Always replace with HQ8 Philips

Shaving Heads.

ENGLISH18

Cleaning

- Use Cleaning spray (HQ110) to clean the shaving

heads thoroughly.

Environment

Do not throw away the appliance with the normal

household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. By doing

this, you help to preserve the environment.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate

worldwide guarantee leaet.

Guarantee restrictions

The shaving heads (cutters and guards) are not

covered by the terms of the international guarantee

because they are subject to wear.

Troubleshooting

This chapter summarises the most common

problems you could encounter with the appliance.

If you are unable to solve the problem with the

information below, visit www.philips.com/

support for a list of frequently asked questions or

contact the Consumer Care Centre in your country.

ENGLISH 19

Problem Possible cause Solution

The shaver does

not shave as

well as it

used to.

The shaving heads

are damaged or

worn.

Replace the shaving heads

(see chapter ‘Replacement’).

Foam or gel

residues clog up

the shaving heads.

Rinse the shaving unit under a

hot tap (see chapter ‘Cleaning

and maintenance’).

Long hairs

obstruct the

shaving heads.

Clean the shaving heads one

by one (see chapter ‘Cleaning

and maintenance’).

You have not

inserted the

shaving heads

properly.

Make sure that the projections

of the shaving heads t exactly

into the recesses (see chapter

‘Cleaning and maintenance’).

The shaver does

not work when

I press the

on/off button.

The rechargeable

battery is empty.

Recharge the battery

(see chapter ‘Charging’).

The temperature

of the shaver is

too high. In this

case, the shaver

does not work.

As soon as the temperature

of the shaver has dropped

sufciently, you can switch

on the shaver again.

The shaver

does not work,

although it is

connected to

the mains.

The shaver is not

designed to be

used directly from

the mains.

Recharge the battery

(see chapter ‘Charging’) and

disconnect it from the mains.

ENGLISH20

ページが読み込まれています...

Philips AT798/16 ユーザーマニュアル

Philips AT798/16 ユーザーマニュアル

他の言語で

関連論文