RayRun N12 Single Color Wireless Remote Control LED Dimmer ユーザーマニュアル

N12 single color LED dimmer is designed to drive

constant voltage LED products in voltage range of DC5-

24V. The main unit works with a RF remote controller, user

can adjust LED brightness on the remote controller. The

main unit is powered by DC power supply and receives

remote controller commands to drive LED fixtures.

Single Color LED Dimmer

Wireless Remote Control

Full Protection High Power

Wireless Remote

Easy Operation Compact Size

Wide Voltage Range

1. Power supply input

Install positive power cable into the terminal marked

with ‘+’ and negative power cable into the terminal marked

with ‘-’. The controller can accept DC power from 5V to

24V, the output voltage is the same as the power supply, so

please make sure the LED rated voltage is same as the

power supply.

Do not power on the controller until all connection is

firmly finished.

2. LED output

Connect LED fixtures to this terminal. Install positive

LED load cable into the terminal marked with ‘+’ and

negative cable into the terminal marked with ‘-’. Please

make sure the LED rated voltage is same as the power

supply and the maximum load current is lower than

controller’s rated current.

The controller will run into protection if the output is

overloaded or short circuited. The indicator will flash red

color and stop working in this case, Please check the

wiring and load current to remove the fault.

3. Work status indicator

This indicator displays all working status of the

controller. It shows different events as following:

Steady green: Normal working.

Single green blink: Command received.

Long single yellow blink: Reach brightness limit.

Red flash: Overload protection.

Yellow flash: Over heat protection.

Green flash 3 times: New remote controller paired.

4. Turn ON / OFF

Press this key to switch on or off the controller. Press

and hold this key will force to switch off the controller.

Main unit will memorize the on/off status and will restore

to the previous status on next power on.

5/6. Brightness control

Press the upward key to increase brightness and press

the downward key to decrease. The brightness will change

smoothly when hold pressing these two keys.

The controller applies brightness gamma correction on

dimming control, makes the brightness tuning more

smooth to human sense.

87mm

24mm

72mm

1 2

7. Remote indicator

This indicator blinks when remote controller is

working. If the indicator flash slowly when pressing keys, it

means the remote battery is nearly empty and please

change the battery in this case. The battery model is

CR2032.

Model: N12

IntroductionIntroduction

Dimension

Wiring & Indicator

Functions

2 3

Please use remote controller to turn on the unit if it

was switched to off status before previous power cut.

Model

N12

Brightness grade

11 levels

PWM grade

4000 steps

Overload protection

Yes

Overheat protection

Yes

Working voltage

DC 5-24V

Remote frequency

433.92MHz

Remote control distance

>15m at open area

Rated output current

1x10A

Controller dimension

87x24x15mm

8. Using the remote

The RF wireless remote signal can pass through some

nonmetal barrier. For proper receiving remote signal,

please do not install the controller in closed metal parts.

9. Pair a new remote controller

The remote controller and main unit is 1 to 1 paired for

factory default. It’s possible to pair maximum 5 remote

controllers to one main unit and each remote controller

could be paired to any main unit.

You could pair a new remote controller to main unit by

following steps:

1). Plug off the power of main unit and plug in again

after more than 5 seconds.

2). Press and keys simultaneously for about 3

seconds, within time of 10 seconds after the main unit

powered on.

10. Recognize current remote only

11. Protection

The main unit has full protection function for wrong

wiring, output short circuit, overload and overheat. The

controller will protect itself from damage at these extreme

conditions and could automatically recover when working

condition is good.

To avoid the protection, please ensure the LED fixtures

are capable for constant voltage driving and in rated range,

the cables are well connected and insulated. Also please

install the controller with good ventilation and heat

dissipation condition.

In some cases, one main unit might be paired with

several remote controllers but extra remote controllers are

no longer needed. User could simply pair the current

using remote to main unit again, then the main unit will

dis-pair all other remote controllers and recognize current

one only.

Operation

14 15

Specification

N12单⾊LED控制器⽤来驱动电压范围为5V到

24V内的恒压LED产品。⽤⼾可以通过射频遥控器来调

节LED灯具的亮度。控制器需要直流电源供电，并根据

接收到的遥控器指令驱动LED灯具，实现亮度调节功

能。

按向上键增加亮度，按向下键降低亮度。⻓按亮度

调节键时亮度会连续平滑变化。

本机的调光控制应⽤了伽玛校正原理，可以使亮度

调节更加顺滑，更符合⼈眼的视觉体验。

型号:N12

2 3

单⾊LED控制器

RF⽆线遥控器简介

尺⼨

接线&指⽰灯

1.电源输⼊

控制器可接受电压为5V到24V的直流电源供电，请

将正极电源线安装到标有“+”的端⼦，将负极电源线安

装到标有“-”的端⼦。控制器的输出电平与电源输⼊电

压相同，请确保LED灯具额定电压与电源相同，且电源

的功率满⾜控制器和灯具的需求。

为确保安全，请在断电的情况下连接电缆。

2.LED输出

3.状态指⽰灯

该指⽰灯显⽰控制器的⼯作状态。它显⽰了不同的

事件，如下所⽰：

绿⾊常亮：正常⼯作。

绿⾊单闪：收到命令。

⻩⾊慢闪：亮度或速度极限。

红⾊闪烁：过载保护。

⻩⾊闪烁：过热保护。

绿⾊闪烁3次：新遥控器配对成功。

4.开/关

此按键可开启或关闭控制器。按住此键可以强制关

闭控制器。控制器会记忆断电前的开关状态，如果断电

前为关闭状态，下次通电后请使⽤遥控器开启。

功能

5/6.亮度调节

7.遥控器指⽰灯

按下遥控器按键时，该指⽰灯会快速闪烁。如果指

⽰灯慢闪，则说明遥控器电池电量已耗尽，请更换遥控

器电池（CR2032型纽扣电池）。

87mm

24mm

72mm

1 2

将LED灯具连接到端⼦。将LED正极电缆安装到标

有“+”的端⼦中，将负极电缆安装到标有“-”的端⼦中。

请确保LED额定电压与电源相同，并且最⼤负载电流低

于控制器额定电流。

如果输出出现过载或短路的情况，控制器会⾃动进

⼊保护功能。此时指⽰灯会闪烁红⾊并停⽌⼯作，请及

时检查接线和负载电流以排除故障。

全功能保护高功率

无线遥控

简易操作小尺寸

宽电压输入

遥控器和控制器出⼚默认为1对1的配对状态。1个控

制器最多可配对5个遥控器，⽽遥控器可配对到任意的

控制器。

如需配对新遥控器，请按以下两个步骤操作：

1）断开控制器电源，并在超过5秒后重新通电。

2）在控制器通电后的10秒内，同时按住新遥控器

键和键约3秒钟。

配对成功后，控制器指⽰灯将闪烁3次提⽰配对成

功。

14 15

操作⽅法

8.使⽤遥控器

使⽤前请拔出遥控器电池绝缘⽚。RF⽆线遥控信号

可以穿过⼀定的⾮⾦属屏障。为了保证控制器的接收效

果，请勿将控制器安装在有⼤⾯积⾦属遮挡的位置。

9.与新遥控器配对

10.保留当前遥控器并清除其他遥控器

在控制器已与多个遥控器配对，⽽仅想保留当前遥

控器的情况下，可以将正在使⽤的遥控器与控制器再进

⾏⼀次配对操作，此后控制器将清除其他已配对的遥控

器⽽仅保留当前使⽤的遥控器。

11.保护功能

本控制器具有完善的保护功能，可以最⼤程度的防

⽌因接线错误、负载短路、过载或过热⽽引起的产品损

坏。当发⽣以上异常状态时，控制器将停⽌⼯作，同时

指⽰灯会闪烁⻩⾊或者红⾊。当⼯作状态良好时，控制

器会尝试恢复正常⼯作。

当控制器进⼊保护状态时，请检查指⽰灯的状态，在

不同的闪烁状态下应检查相应的故障：

红⾊闪烁：请检查输出电缆是否短路、负载电流是否

过⾼，并请确保灯具为恒压类型且兼容PWM调光⽅式。

⻩⾊闪烁：请检查控制器的安装环境以及负载功率、

并确保控制器散热条件良好且负载功率在额定范围之

内。

规格

型号

N12

亮度可调级数

11级

PWM分辨率

4000级

过载保护

有

过热保护

有

⼯作电压

DC5-24V

遥控器⼯作频率

433.92MHz

遥控器⼯作距离

空旷地带>15⽶

额定输出电流

1x10A

控制器尺⼨

87x24x15mm