Dell PowerEdge R300 ユーザーガイド

カテゴリー
ラックアクセサリー
タイプ
ユーザーガイド

このマニュアルも適しています

Rack Installation Guide
Guide d'installation du rack
Rack-Installationsanleitung
ラック取り付けガイド
Guía de instalación del rack
www.dell.com | support.dell.com
Rack Installation Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2005 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own
November 2005 P/N YC588 Rev. A00
Contents 3
Contents
1 Four-Post Rack Installation. . . . . . . . . . . . . . . . . . . . . . . 5
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY: Rack Mounting of Systems
. . . . . . . . . . . . . . . . . . . . . 5
General Installation Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . 6
Before You Begin
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important Safety Information
. . . . . . . . . . . . . . . . . . . . . . . . . 7
Rack Requirements for VersaRails
. . . . . . . . . . . . . . . . . . . . . . 7
Rack Stabilizer Feet
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Recommended Tools and Supplies
. . . . . . . . . . . . . . . . . . . . . . 7
Sliding Rails Rack Kit Contents
. . . . . . . . . . . . . . . . . . . . . . . . 8
Static Rails Rack Kit Contents
. . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Tasks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Removing the Rack Doors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Marking the Rack
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Configuring the Sliding Rail Assemblies (Sliding Rail Kits Only)
. . . . . . . . 13
Installing Chassis Static Rail Modules (Static Rail Kits Only)
. . . . . . . . . 14
Installing the Mounting Rails in the Rack
. . . . . . . . . . . . . . . . . . . . 15
Installing the System in the Rack
. . . . . . . . . . . . . . . . . . . . . . . . 18
Installing a System With Sliding Rails
. . . . . . . . . . . . . . . . . . . 18
Installing a System With Static Rails
. . . . . . . . . . . . . . . . . . . . 20
Replacing the Rack Doors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Tray and Cable-Management Arm (Sliding Rail Kits Only)
. . . 22
Installing the Tray
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Cable-Management Arm
. . . . . . . . . . . . . . . . . . . 23
Routing Cables
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing the System From the Rack
. . . . . . . . . . . . . . . . . . . . . . 25
Removing a System With Sliding Rails
. . . . . . . . . . . . . . . . . . . 25
Removing a System With Static Rails
. . . . . . . . . . . . . . . . . . . . 25
4 Contents
2 Two-Post Rack Installation . . . . . . . . . . . . . . . . . . . . . . . 27
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SAFETY: Rack Mounting of Systems
. . . . . . . . . . . . . . . . . . . . 27
Before You Begin
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Important Safety Information
. . . . . . . . . . . . . . . . . . . . . . . . 28
Recommended Tools and Supplies
. . . . . . . . . . . . . . . . . . . . . 28
Rack Kit Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installation Tasks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Marking the Rack
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Universal-Hole Spacing Racks
. . . . . . . . . . . . . . . . . . . . . . . 30
Wide-Hole Spacing Racks
. . . . . . . . . . . . . . . . . . . . . . . . . 31
Installing the Mounting Rails
. . . . . . . . . . . . . . . . . . . . . . . . . . 32
Center-Mount Installation
. . . . . . . . . . . . . . . . . . . . . . . . . 32
Flush-Mount Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing Chassis Static Rail Modules
. . . . . . . . . . . . . . . . . . . . . 36
Installing the System in the Rack
. . . . . . . . . . . . . . . . . . . . . . . . 37
Removing the System From the Rack
. . . . . . . . . . . . . . . . . . . . . . 37
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Four-Post Rack Installation 5
Four-Post Rack Installation
Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect your system
and working environment from potential damage. For complete safety and regulatory information,
see the
Product Information
Guide
that shipped with your system. Warranty information might be
included in this document or as a separate document.
SAFETY: Rack Mounting of Systems
Observe the following precautions for rack stability and safety. Also refer to the rack installation
documentation accompanying the system and the rack for specific caution statements and
procedures.
Systems are considered to be components in a rack. Thus, "component" refers to any system as well
as to various peripherals or supporting hardware.
CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the
front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing
systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under certain
circumstances. Therefore, always install the stabilizer(s) before installing components in the rack.
After installing system/components in a rack, never pull more than one component out of the rack on its slide
assemblies at one time. The weight of more than one extended component could cause the rack to tip over
and may result in serious injury.
NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a Dell rack
cabinet using the customer rack kit. The installation of your system and rack kit in any other rack cabinet has
not been approved by any safety agencies. It is your responsibility to ensure that the final combination of
system and rack complies with all applicable safety standards and local electric code requirements. Dell
disclaims all liability and warranties in connection with such combinations.
System rack kits are intended to be installed in a rack by trained service technicians. If you install
the kit in any other rack, be sure that the rack meets the specifications of a Dell rack.
CAUTION: Do not move racks by yourself. Due to the height and weight of the rack, a minimum of two
people should accomplish this task.
Before working on the rack, make sure that the stabilizers are secured to the rack, extended to
the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers
on a single rack or front stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the rack first.
6 Four-Post Rack Installation
Make sure that the rack is level and stable before extending a component from the rack.
Use caution when pressing the component rail release latches and sliding a component into or out
of a rack; the slide rails can pinch your fingers.
Do not overload the AC supply branch circuit that provides power to the rack. The total rack load
should not exceed 80 percent of the branch circuit rating.
Ensure that proper airflow is provided to components in the rack.
Do not step on or stand on any component when servicing other components in a rack.
General Installation Instructions
This installation guide provides instructions for trained service technicians installing one or more systems
in a rack cabinet. The RapidRails™ rack kit can be installed in all the system manufacturer's rack cabinets
without tools, and the VersaRails™ rack kit can be installed in most industry-standard rack cabinets. The
procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is required for
each system to be installed in the rack cabinet.
This section includes procedures for the following four-post rack kits:
Sliding rails rack kit
Static rails rack kit (RapidRails and VersaRails versions)
(See "Two-Post Rack Installation" on page 27 for instructions on installing a static rails kit in a two-post
rack.)
Before You Begin
Before you begin installing your system in the rack, carefully read "Safety Instructions," found earlier
in this guide, as well as the safety instructions found in your Product Information Guide for additional
information.
CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current system
before attempting to install the next system.
CAUTION: Rack cabinets can be extremely heavy and move easily on their casters. They do not have brakes. Use
extreme caution while moving the rack cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid
long or steep inclines or ramps where loss of cabinet control may occur. Extend the leveling feet for support and
to prevent the cabinet from rolling.
NOTE: For instructions on installing the system itself, see ""Installing the System in the Rack" on page 18.
Four-Post Rack Installation 7
Important Safety Information
Observe the safety precautions in the following subsections when installing your system in the rack.
CAUTION: You must strictly follow the procedures in this document to protect yourself as well as others who
may be involved. Your system may be very large and heavy and proper preparation and planning are important to
prevent injury to yourself and to others. This precaution becomes increasingly important when systems are
installed high up in the rack.
CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for your system.
Using the rack kit for another system may result in damage to the system and personal injury to yourself and to
others.
Rack Requirements for VersaRails
NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that meets the
specifications of American National Standards Institute (ANSI)/Electronic Industries Association (EIA) standard
ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and Deutsche Industrie Norm (DIN) 41494.
One rack kit is required for each system that is installed in a rack.
Rack Stabilizer Feet
CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the front
stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing systems in a
rack could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.
Therefore, always install the stabilizer(s) before installing components in the rack.
The stabilizer feet help prevent the rack from tipping over. See the documentation provided with the rack
cabinet for instructions on installing and anchoring the stabilizer feet.
Recommended Tools and Supplies
You may need the following items to install the system in a four-post rack cabinet:
#2 Phillips screwdriver
Masking tape or a felt-tip pen, for use in marking the mounting holes to be used
8 Four-Post Rack Installation
Sliding Rails Rack Kit Contents
One pair of slide assemblies (convertible to RapidRails or VersaRails configuration)
One cable-management arm
•One tray
One status indicator cable (if applicable)
Tie wraps to secure the cables to the cable management arm
Eight 10-32 x 0.5-inch flange-head Phillips screws (used in VersaRails configuration only)
NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and number
of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.
Figure 1-1. Sliding Rails Rack Kit Contents
1 tray 2 slide assemblies (2) 3 10-32 x 0.5-inch flange-head Phillips
screws (8) (VersaRails configuration only)
4 tie wraps 5 status indicator cable
(if applicable)
6 cable-management arm
1
2
3
5
6
4
Four-Post Rack Installation 9
Static Rails Rack Kit Contents
One pair of static mounting rails with either VersaRails brackets or RapidRails brackets.
One pair of chassis static rail modules
10-32 x 0.5-inch flange-head Phillips screws (8) (VersaRails kits only)
Releasable tie wraps (2) (not shown in Figure 1-2)
NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and number
of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.
Figure 1-2. Static Rails Rack Kit Contents
1 10-32 x 0.5-inch flange-head
Phillips screws (8)
(VersaRails kits only)
2 static mounting rails (2) 3 chassis static rail modules (2)
FRONT
L
1
3
2
10 Four-Post Rack Installation
Installation Tasks
Installing a rack kit involves performing the following tasks (described in detail in subsequent sections)
in their numbered order:
1
Removing the rack doors
2
Marking the rack
3
Configuring the sliding rail assemblies (sliding rail kits only)
4
Installing chassis static rail modules (static rail kits only)
5
Installing the mounting rails in the rack
6
Installing the system in the rack
7
Installing the tray and cable-management arm (sliding rail kits only)
8
Routing cables
9
Replacing the rack doors
Removing the Rack Doors
See the procedures for removing doors in the documentation provided with your rack cabinet.
CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install them
by yourself.
CAUTION: Store the two doors where they will not injure someone if the doors accidently fall over.
Marking the Rack
For a 1-U system, you must allow 1 U (44 mm, or 1.75 inches) of vertical space for each system you install
in the rack.
Rack cabinets that meet EIA-310 standards have an alternating pattern of three holes per rack unit with
center-to-center hole spacing (beginning at the top hole of a 1-U space) of 15.9 mm, 15.9 mm, and 12.7 mm
(0.625 inch, 0.625 inch, and 0.5 inch) for the front and back vertical rails (see Figure 1-3). Rack cabinets may
have round or square holes.
NOTE: The vertical rails may be marked by horizontal lines and numbers in 1-U increments. If you want, you can
make a note of the number marking on the rack’s vertical rail. It is not necessary to mark or place tape on the rack.
Four-Post Rack Installation 11
Figure 1-3. One Rack Unit
CAUTION: If you are installing more than one system, install the mounting rails so that the first system is
installed in the lowest available position in the rack.
To mark the rack, perform the following steps:
1
Place a mark (or tape) on the rack's front vertical rails where you want to locate the bottom
of the system you are installing in the rack.
The bottom of each 1-U space is at the middle of the narrowest metal area between holes (marked
with a horizontal line on some rack cabinets—see Figure 1-4).
2
Place a mark 44 mm (1.75 inches) above the original mark you made (or count up three holes in a rack
that meets EIA-310 standards) and mark the rack's front vertical rails with a felt-tipped pen or masking
tape (if you counted holes, place a mark just above the top hole). This mark or piece of tape indicates
where the system's upper edge will be located on the vertical rails (see Figure 1-4).
1 U (44 mm or 1.75 inches)
12.7 mm (0.5 inch)
15.9 mm (0.625 inch)
15.9 mm (0.625 inch)
12.7 mm (0.5 inch)
12 Four-Post Rack Installation
Figure 1-4. Marking the Vertical Rails
1 marks on vertical rail (2)
1
Four-Post Rack Installation 13
Configuring the Sliding Rail Assemblies (Sliding Rail Kits Only)
The sliding rail assembly has a rotating mounting bracket at each end of the rail. The position of the
bracket determines whether the rail assembly is used as a RapidRail or a VersaRail. The RapidRail side of
the bracket has a hook and a latch that secure it to the vertical rail. The VersaRail side of the bracket has
three holes and uses screws to attach it to the vertical rail.
NOTE: The rack kit ships with the sliding rail assemblies in the RapidRails configuration.
To rotate the mounting bracket and change the mounting rails from RapidRails to VersaRails
(see
Figure 1-5
):
1
Lift the release lever on the rotating mounting bracket.
2
Rotate the bracket and slide it up off the two shoulder standoffs.
3
Continue to rotate the bracket 180 degrees until you can set the notches back over the shoulder
standoffs.
4
Rotate the bracket back in the opposite direction on the shoulder standoffs until the bracket clicks
into place.
Figure 1-5. Changing the Position of the Rotating Mounting Bracket
1 rotating bracket 2 release lever 3 shoulder standoffs (2)
4 notches (2) 5 mounting bracket flange
(RapidRails configuration shown)
1
2
4
3
5
14 Four-Post Rack Installation
Installing Chassis Static Rail Modules (Static Rail Kits Only)
NOTE: You do not need to remove the optional front bezel to install or remove the chassis static rail modules from
the chassis.
1
To install a rail module, locate the three keyhole slots on the rail module and the corresponding
shoulder screws on the side of the system (see Figure 1-6).
2
Place the rail module against the side of the system so that the shoulder screws fit through the round
portion of the keyhole slots, then slide the module towards the back of the system.
3
Repeat steps 1 and 2 to install the other rail module.
To remove a
rail module
from the chassis, pull up on the release latch, then slide the rail forward and
remove the rail module from the chassis.
Figure 1-6. Installing and Removing Static Rail Chassis Modules
1 keyhole slots (6) 2 shoulder screws (6) 3 release latch
4 rail modules (2) 5 system
4
2
3
1
5
Four-Post Rack Installation 15
Installing the Mounting Rails in the Rack
NOTE: The following instructions apply to both sliding mounting rails and static mounting rails.
Installing RapidRails Mounting Rails
1
At the front of the rack cabinet, position one of the mounting rails so that its mounting-bracket flange
fits between the marks or tape you placed (or numbered locations) on the vertical rails in "Marking the
Rack" (see Figure 1-7).
The top mounting hook on the front mounting-bracket flange should enter the top hole between the
marks you made on the vertical rails.
Figure 1-7. Installing RapidRails Mounting Rails
1 mounting hooks (2) 2 push buttons (2) 3 mounting rails (2)
front of rack
1
2
3
16 Four-Post Rack Installation
2
Push the mounting rail forward until the mounting hook enters the square hole, and then push down
on the mounting-bracket flange until the mounting hook seats and the push button extends through
the lower square hole (see Figure 1-7).
3
At the back of the cabinet, pull back on the mounting-bracket flange until the mounting hook enters
the upper square hole, and then push down on the flange until the mounting hook seats and the push
button extends through the lower square hole.
4
Repeat step 1 through step 3 for the mounting rail on the other side of the rack.
5
Confirm that the mounting rails are mounted at the same vertical position on both sides of the rack.
Installing the VersaRails Mounting Rails
1
At the front of the rack cabinet, position one of the mounting rails so that its mounting-bracket flange
fits between the marks you placed (or numbered locations) on the vertical rails in "Marking the Rack"
(see Figure 1-8).
The three holes on the front of the mounting-bracket flange should align with the holes between the
marks you made on the front vertical rail.
2
Install two 10-32 x 0.5-inch flange-head Phillips screws in the upper and lower holes in the mounting-
bracket flange to secure the mounting rail to the front vertical rail.
3
At the back of the cabinet, pull back on the mounting-bracket flange until the mounting holes align
with their respective holes on the back vertical rail.
4
Install two 10-32 x 0.5-inch flange-head Phillips screws in the upper and lower holes in the mounting-
bracket flange to secure the mounting rail to the back vertical rail.
5
Repeat step 1 through step 4 for the mounting rail on the other side of the rack.
6
Ensure that the mounting rails are mounted at the same position on the vertical rails on each side
of the rack.
Four-Post Rack Installation 17
Figure 1-8. Installing VersaRails Mounting Rails
1 mounting-bracket flange 2 10-32 x 0.5-inch flange-head
Phillips screws
(4 per mounting rail)
3 mounting rails (2)
front of rack
1
2
3
18 Four-Post Rack Installation
Installing the System in the Rack
CAUTION: If you are installing more than one system, install the first system in the lowest available position
in the rack.
CAUTION: Because of the size and weight of the system, never attempt to install the system in the mounting rails
by yourself.
Installing a System With Sliding Rails
1
Pull the two inner slide rails out of the rack until they lock in the fully extended position
(see Figure 1-9).
2
Lift the system into position above the extended slides.
The three shoulder screws on each side of the system fit into the corresponding J-slots on the inner
slide assemblies (see Figure 1-9).
3
Lower the back of the system while aligning the back shoulder screws on the sides of the system with
the back J-slots on the slide assemblies.
4
Engage the back shoulder screws into their respective J-slots.
5
Lower the front of the system and fit the middle and front shoulder screws into the J-slots in the slide
assemblies.
The system release latch at the front of the inner slide rail will snap back as the shoulder screw passes
into the front slot. Use this system release latch when you wish to remove the system from the slide
assemblies.
6
Press the slide-release latch on the outside of each inner slide, then push the system into the rack.
7
Install the cable-management arm. See "Installing the Tray and Cable-Management Arm
(Sliding Rail Kits Only)" on page 22.
8
Tighten the thumbscrews on the rack front panel to secure the slide assemblies to the rack.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202

Dell PowerEdge R300 ユーザーガイド

カテゴリー
ラックアクセサリー
タイプ
ユーザーガイド
このマニュアルも適しています