2. Yamaha
  3. Ri8
Ri8

Yamaha Ri8, D2, Rio1608, Rio3224, RMio64, Ro8, RSio64, Tio1608, V3 ユーザーガイド

  • こんにちは！Yamaha Rシリーズ、Tio1608-D、Tio1608-D2オーディオインターフェースのファームウェアアップデートガイドに関するご質問にお答えします。このガイドでは、R Remoteを使ったファームウェアアップデート手順、注意点、そしていくつかのデバイスの互換性について詳しく説明しています。どのようなご質問でもお気軽にお尋ねください！
  • アップデート前に何をすべきですか？
    R Remoteを使用するには何が必要ですか？
    アップデート中にデバイスの電源を切ったり、ケーブルを切断したりしても大丈夫ですか？
    ファームウェアファイルの選択方法を教えてください。
    Tio1608-D2をアップデートする際の注意点は何ですか？
R Series Firmware Update Guide 1
R Series, Tio1608-D and Tio1608-D2
Firmware Update Guide
This guide explains how to update the R series, Tio1608-D and Tio1608-D2 firmware by using the R Remote
(V5.9 or later).
Precautions
Check the firmware version of the target device before updating. Since Rio3224-D, Rio1608-D, Ri8-D, Ro8-
D, and RMio64-D before firmware version 3.11 are not supported by R Remote update function, you once
need to update the firmware to V3.11 by using the exclusive update software for each product. The
exclusive update software for each product is compressed with the firmware V3.11 which you can
download from the following website:
https://www.yamahaproaudio.com/
To use R Remote, Dante Controller must be installed. You can download Dante Controller from the
download page of the following Audinate website:
https://www.audinate.com/products/software/dante-controller/
Note that the device may be damaged if you fail to follow these instructions properly, or turn off the device
or disconnect the cable while the update is in progress.
Yamaha Corporation owns exclusive copyrights for the firmware, its update program, and the update guide.
It is prohibited to duplicate or modify the firmware, software or guides, in part or in their entirety, without
permission from the copyright owner.
The screen shots in this guide are for use with this update procedure only and may be different from the
actual screen shots.
The company names and product names in this document are the trademarks or registered trademarks of
their respective companies.
EN
R Series Firmware Update Guide 2
Update operation
This section describes how to update the firmware.
1. Start R Remote. Choose “Tool” “Firmware Update” from the menu of R Remote.
Firmware Updater starts up.
2. (In the case of RMio64-D) Quit the NUAGE Workgroup Manager if it is running.
3. Press the “Select” button and select the firmware “xxxx_v*_**_rrmt.bin” to be updated.
Devices that can be updated appear in the device information area.
Set these three items to the same subnet: the device’s IP address, the device’s Dante module IP
address and the computer’s IP address. If you are using static IP addresses or IP addresses
assigned by the DHCP server, check the IP address setting.
The characters “xxxx” represent the product name. (Tio1608-D2 shares files with Tio1608-D.
Firmware prior to V2 cannot be written.) Also, “*_**” represents the firmware version number
(e.g., “rio3224-d_v4_10_rrmt.bin”).
When updating Tio1608-D2, make sure the Tio1608-D Compatibility Mode is disabled.
When you select an old firmware which is not supported by R Remote, “invalid file” appears and
the update cannot be started.
If the firmware of the device is an older version than the firmware file, the checkbox for its device
will be automatically checked.
If the firmware of the device is a newer version or a same version, you will need to check manually
to the checkbox of the firmware to update.
4. Press the “Update” button to start the update.
5. When the update is complete, a popup window appears. Press the "OK" button.
6. Turn the updated device off and then on again.
For details on updating the unit, refer to the “R Remote Version 5.9 User’s Guide” available on the website.
https://www.yamahaproaudio.com/
© 2016 Yamaha Corporation
Published 07/2023 YJET-F0
/