1UL
1
Thank you, and congratulations on your choice of the Roland
V-Stand KS-V7.
* V-Stand™ is a trademark of Ultimate Support Systems, Inc.
• Can be set to optimal height to match each style of
performance
• Allows ample foot space for pedal placement
• Compact size, folds quickly and easily for superior
portability
• Extremely sturdy construction, holds up to 250 lbs (113 kg)
Main Features
Names of Things
Inner Vertical Strut
Cable Clip
Outer Vertical Strut
Legs
Arms
Height Setting Numbers
Knob
Collar Lock
Angle Adapter
Leg Securing Screws
•
•
•
•
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
(p. 5). These sections provide important information concerning the proper operation of the unit. Additionally, in
order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual
should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
201a
Copyright © 2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
CORPORATION.
202
©
Owner’s Manual
2
1.
Place the V-Stand on the floor.
Set up the stand in a stable, level location.
2.
Release the collar lock and spread the legs out until
they are at the position at which they no longer
move.
3.
Securely tighten the leg securing screws (triangular-
headed screws) at the left and right leg base joints.
4.
Raise the vertical struts until they are positioned
straight up, then spread them out to the left and right
until they come to a stop.
5.
Flip the arms over and set them in a level position.
Setting Up the Stand
* When releasing the collar
lock, do not pull with
excessive force. Otherwise,
you risk getting your
hands or fingers pinched,
or damaging the collar
lock.
* Be sure to spread out the
legs as far as they will go.
The stand may fall over if
the legs are not fully
opened, causing the
keyboard to fall.
Collar Lock
* Be sure to tighten the
screws on both the left
and right legs securely.
Leg Securing Screws
* Spread the struts outward
carefully so as not to allow
your hands or fingers to be
pinched.
* Position the arms carefully
so as not to allow your hands
or fingers to be pinched.
1.
2.
3.
4.
5.
3
6.
Pull the knobs out towards you and set the inner
struts to the desired height.
Check the height setting numbers marked on the inner struts to
make sure that both the left and right legs are set to the same
height.
Adjusting the Strut Angle
You can adjust the degree to which the struts open by
attaching or removing the angle adapters.
To set the struts at an increased angle, remove the angle
adapters on the outer sides of the strut hinges (refer to Fig. B).
• Set the keyboard so that the center of the keyboard is aligned
with the midpoint of the stand.
• Set the keyboard so that it rests on the rubber portions of the
arms.
• Adjust the strut height and angle so that the stand is the
appropriate width for the keyboard and that any rubber feet on
the underside of the keyboard are not resting directly on top of
the arms.
• Run cables used for connecting the keyboard through the struts’
cable clip. Using the keyboard and stand with the cables
swinging loosely is dangerous, so be sure to keep the cables
secured to the strut.
• Do not move the stand with the keyboard still resting on it. This
may cause the keyboard to topple and fall.
Do not play the keyboard so vigorously that the stand shakes left
and right or the stand’s legs rise off the floor. This may cause the
keyboard to topple and fall.
Precautions to Observe When
Setting the Keyboard on the Stand
Note to Observe When Performing
Knob
* Of the numbers for setting the strut
height, use only the numbers from 1
through 12. Setting the height at 13 is
not recommended, as this may make
the stand unstable.
* Take care not to let your hands or
fingers get caught and pinched in the
notches for the height setting numbers.
Angle Adapter
Fig. A Fig. B
* Attach the angle adapters
on the inner sides of the
strut hinges to prevent
from losing them (refer to
Fig. B).
* When removing the angle
adapters, be sure to remove
them from both struts.
Never use the stand with
the adapter removed from
only one side, as this will
cause the keyboard to lean
dangerously to one side.
6.
•
•
•
•
•
4
1.
Disconnect all cables and take the keyboard off the
stand.
2.
Pull the knobs out towards you and set the inner
struts to the lowest position.
3.
Lift up the arms and flip them over so that they stop
on the back sides of the struts.
4.
Swing the struts inward and down to the floor.
5.
Loosen the leg securing screws.
6.
Swing the left and right legs closed, and then secure
them with the collar lock.
Folding the Stand
Knob
* Be sure to hold the strut firmly with
one hand while pulling the knob with
your other hand.
* Never just pull the knob, as this can
cause the inner strut to drop suddenly.
1
2
* You can fold the stand
smoothly by slightly
raising the stand where
the bottom of the struts
are joined ( ) and
closing the legs ( ).
1
2
1
2
1.
2.
3.
4.
5.
6.
ページが読み込まれています...
ページが読み込まれています...
8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
