Dell PowerEdge R420xr 取扱説明書

Dell PowerEdge R420xr

901D Reinforcement Kit

901D 强化套件

Kit de renforcement 901D

901D-Erweiterungssatz

901D 強化キット

901D 보완 키트

Kit de refuerzo 901D

901D Destek Kiti

Dell PowerEdge R420xr

901D Reinforcement Kit

Installation Guide

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

This product is protected by U.S. and international copyright and intellectual property laws. Dell™

and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other

marks and names mentioned herein may be trademarks of their respective companies.

2014 - 10 8JK58 Rev. A01

Installation Guide 3

Introduction

This document describes the procedure for installing the components in the

901D reinforcement kit on Dell PowerEdge R420xr systems.

WARNING: Opening or removing the system cover when the system is on may

expose you to a risk of electric shock.

CAUTION: Many repairs may only be done by a certified service technician.

You should only perform troubleshooting and simple repairs as authorized in your

product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered

by your warranty. Read and follow the safety instructions that came with the product.

Contents of 901D Reinforcement Kit

Item No. Dell Part

Number

(DPN)

Description Quantity

Electrical insulator 0M4XF INSUL,MYLAR,PCI BRKT,R2,R420,X 1

Screw 23FYT SCR,M2.5X.45X4MM,FLH,PH,CSKT,Z 6

Screw VW2J4 SCR,4-20X3/8,TORX,TF,SS,PLST,X 1

Screw JNG28 SCR,4-40X7MM,PH,PHH,ZPS,XR 3

Bracket assembly

FYGC8 ASSY,BRKT,PCI-LOCK,R2,R420,XR 1

Plastic block TGNK5 BRKT,BLOCK,PCI-LOCK,R1,R420,XR 1

System board lock

V5PYK CLP,PLSTC,PCI-CARD,R420XR 1

PSU lock bracket

X23KY BRKT,PSU,RET,1U,R420,XR,OEM 1

PCe card support

bracket

T621V BRKT,PCI-LOCK,R1,R420,XR 1

Battery clip 5C6HG CLP,PLSTC,BATTERY,R420XR 2

Server tie wrap 6N5P9 STRAP,CBL,6,TIE-WRAP,RMVBL,XR 6

Instruction manual 8JK58 ASSEMBLY INSTRUCTION 1

4 Installation Guide

Inside the System

NOTE: The components used to illustrate the installation procedure may vary from

the actual components.

The following components inside the system will be reinforced.

Figure 1-1. Components That will be Reinforced

1 PSU 2 PERC card

3 PCIe card riser 2 4 system board lock

5 PCIe card riser 1

Installation Guide 5

Installing the PERC Battery Clip

1

Turn off the system and attached peripherals, and disconnect the system

from the electrical outlet.

2

Loosen the three captive screws on the top of the system cover.

3

Loosen the thumb screws that secure the back of the system cover to

the chassis.

4

Hold the thumb screws and slide the system cover toward the back of

the system.

5

Remove the system cover. For more information see your system Owner’s

Manual at

dell.com/poweredgemanuals

.

6

Remove the PERC card by pressing down on the two release levers at the

edge of the card to disengage the card from the connector. For more

information see the topic Integrated Storage Controller Card in your

system Owner’s Manual at

dell.com/poweredgemanuals.

7

Loosen the screw on the PERC battery clip to open the battery clip.

8

Install the PERC battery clip on the PERC battery as shown in Figure 1-1.

9

Tighten the screw to secure the PERC battery using the battery clip.

10 Install the PERC battery assembly on the system board. For more

information, see the topic Integrated Storage Controller Card in your

system Owner’s Manual at dell.com/poweredgemanuals.

6 Installation Guide

Figure 1-2. Installing the PERC Battery Clip

Replacing the System Board Lock

1

Open the system.

2

Locate the system board lock. See Figure 1-1.

3

Pressing down on the black tab, slide the existing system board lock in the

direction of the arrow as shown in Figure 1-3.

1 screw on the PERC battery clip 2 PERC battery clip (

DPN: 5C6HG)

3 PERC battery assembly 4 connector on system board

Installation Guide 7

Figure 1-3. Removing the System Board Lock

4

Press the tab on the system board lock as shown in Figure 1-4 and install it

on the system board

NOTE: The new system board lock can be identified by the square feature.

1 existing system board lock 2 tab

8 Installation Guide

Figure 1-4. Installing the New System Board Lock

Securing Full Half-Length PCIe Card on Riser 1

1

Install the full half-length PCIe card on riser 1.

2

Slide the system board lock in the direction of the arrow such that the edge

of the PCIe card is secured against the system board lock as shown in

Figure 1-5.

1 square feature 2 system board lock (DPN: V5PYK)

3 tab

Installation Guide 9

Figure 1-5. Securing Full Half-Length PCIe Card Using the System Board Lock

Securing Half-Length PCIe Card on Riser 1

NOTE: Perform this procedure for PCIe expansion cards that are shorter than

half-length PCIe expansion cards.

1

Remove PCIe riser 1 from the system board. For more information, see the

Owner’s Manual at

dell.com/poweredgemanuals

.

2

Remove the screw on PCIe riser 1.

1 system board lock (DPN: V5PYK) 2 full half-length PCIe card

3 PCIe riser 1 connector 4 PCIe riser 1

10 Installation Guide

Figure 1-6. Installing the Plastic Block on Riser 1

3

Locate the Phillips head screw and the plastic block in the

901D

reinforcement kit

.

4

Install the plastic block on riser 1 along with the riser securing tab as

shown in Figure 1-6.

5

Install the riser 1 assembly on the system board.

1 screw (DPN: VW2J4) 2 plastic block (DPN: TGNK5)

3 riser 1 4 riser securing tab

Installation Guide 11

Figure 1-7. Installing the PCIe Bracket on Riser 1

6

Install the PCIe card on riser 1.

7

Secure the card support bracket on riser 1 using the two screws as shown in

Figure 1-7.

1 PCle card support bracket (DPN: T621V) 2 screw (DPN: JNG28)

3 PCIe card 4 PCIe riser assembly

5 plastic block (DPN: TGNK5)

12 Installation Guide

Securing the PCIe Card on Riser 2

1

Locate and remove the PCIe card on riser 2.

2

Unfasten the screw on the PCIe card and install the electrical insulator

tape on the PCB as shown in Figure 1-8.

NOTE: Make sure that the hole on the tape is aligned with the hole on the

PCIe card.

3

Locate the riser 2 bracket assembly (DPN: FYGC8).

NOTE: The riser 2 metal bracket comes as an assembly. Loosen the screws

that hold the plastic bracket and the metal bracket to separate the two

components.

4

Place the plastic block on the system board adjascent to riser 2 such that

Point A is aligned with the PCIe connector as shown in Figure 1-8.

5

Install the PCIe card on riser 2.

6

Slide the plastic block with point A sliding along the PCIe riser connector,

and point B beneath the PCIe card as shown in Figure 1-8.

NOTE: The riser 2 metal bracket comes as an assembly. Loosen the screws

that hold the plastic bracket and the metal bracket to separate the two

components.

7

Align the screw holes on the metal bracket with the screw holes on the

PCIe card and the plastic bracket as shown in Figure 1-8.

NOTE: Adjust the position of the plastic bracket such that the metal bracket

screw holes are aligned with that on the plastic bracket.

8

Place riser 2 metal bracket on PCIe card and secure using a screw as shown

in Figure 1-8.

9

Secure the metal bracket to the plastic bracket using the two screws.

Installation Guide 13

Figure 1-8. Securing the Riser 2 PCIe Card

NOTE: If the PCIe card on riser 2 is PERCHT810, install a battery strap to secure it to

the PCB.

1 PCIe card riser 2 2 PCIe card riser 2 connector

3 screws on metal bracket 4 metal bracket (DPN: FYGC8)

5 screw (DPN: JNG28) 6 electrical insulator tape on PCB (DPN: 0M4XF)

7 plastic block (DPN: FYGC8)

A

B

14 Installation Guide

Installing the PSU Lock

1

Replace the system top cover.

2

Place the PSU lock against the PSU as shown in Figure 1-9.

3

Fasten the three screws on the top side on the system.

4

Fasten the three screws at the bottom of the system.

Figure 1-9. Installing the PSU Lock

1 screws (DPN: 23FYT) 2 screw hole on system top cover (3)

3 PSU lock (DPN: X23KY)

Dell PowerEdge R420xr

901D

强化套件安装指南

注、小心和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

小心：“小心”表示可能会损坏硬件或导致数据丢失，并说明如何避免此类

问题。

警告：“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本产品受美国版权

、国际版权和知识产权法律保护。

Dell

™

和

Dell

徽标是

Dell Inc.

在美国和 /

或其他司法管辖区的商标。本文档中所述及的其它商标和产品名称可能是其各自所属公司的

商标。

2014 - 10 8JK58 Rev. A01

安装指南 17

简介

本文档介绍在 Dell PowerEdge R420xr 系统上安装 901D 强化套件中组件的

操作步骤。

警告：系统处于开启状态时打开或卸下系统护盖会使您有触电的风险。

小心：多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文

件中的授权，或者在联机或电话服务和支持小组的指导下，进行故障排除和

简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围之内。请阅读

并遵循产品附带的安全说明。

901D 强化套件的组成部分

项目号 Dell 部件号

(DPN)

说明数量

电绝缘胶带

0M4XF

绝缘、胶带、 PCI 支架、 R2、 R420、 X

1

螺钉

23FYT

螺钉、 M2.5X.45X4MM、 FLH、 PH、

CSKT、 Z

6

螺钉

VW2J4

螺钉、4-20X3/8、TORX、TF、SS、PLST、X

1

螺钉

JNG28

螺钉、4-40X7MM、PH、PHH、ZPS、XR

3

支架组件

FYGC8

组件、支架、PCI-LOCK、R2、R420、XR

1

塑料块

TGNK5

支架、块、 PCI 锁、 R1、 R420、 XR

1

系统板锁

V5PYK

CLP、 PLSTC、 PCI 卡、 R420XR

1

PSU

锁定支架

X23KY

支架、PSU、RET、1U、R420、XR、OEM

1

PCe 卡支撑架

T621V

支架、 PCI 锁、 R1、 R420、 XR

1

电池固定夹

5C6HG

CLP、塑料、电池、 R420XR

2

服务器绑扎带

6N5P9

束带、CBL、6、绑扎带、XR、RMVBL、XR

6

说明手册

8JK58

组件说明

1

18 安装指南

系统内部组件

注：用于演示安装操作步骤的组件可能会与实际组件不同。

系统中的以下组件将得到强化。

图 1-1. 将强化的组件

1 PSU 2

PERC 卡

3

PCIe 卡提升板 2

4

系统板锁

5

PCIe 卡提升板 1

Dell PowerEdge R420xr 取扱説明書

関連論文

その他の書類