BATTERY HANDLING
Low Battery Indicator
60º
Direction lever
LCD readout Buttons Handle/ Battery compartment
Battery cover
Communication port
3/8" Square Drive
Storage Case
Torque value
P (peak hold mode)
T (track mode) Cancel button Down button
Up button
Menu button
AAA battery x 2pcs (R03UG 1.5V)
Units (N.m, in.lb, ft.lb, kg.cm)
Buzzer
1. If the wrench is not used for an extended period
of time, remove the battery.
2. Keep spare batteries on hand when going on a
long trip or travelling to a cold area.
3. Do not mix battery types or combine used
batteries with new ones.
4. Sweat, oil and so on can prevent a battery's
terminal from making electrical contact. To avoid
this, wipe both terminals before loading any batteries.
5. Dispose of old batteries in accordance with local
ordinances. Do not throw batteries into a fire.
6. Both standard and rechargeable batteries are
available.
7. Check battery if there is no screen display.
Replace battery if necessary.
IMPORTANT NOTE / / /
重要事項
AAA battery (R03UG 1.5V)
(TOSHIBA Battery included)
CHANGING BATTERIES / / /
電池更換
方向撥桿
Release button
釋放鈕 LCD 視窗 按鈕 握把/電池位置
電池蓋
傳輸孔
3/8吋方形套筒接頭
Torque Range: 4-80 Nm
扭力範圍 : 4-80 Nm
收納盒
AAA 電池 x 2 (R03UG 1.5V)
蜂鳴器
• DO NOT open communication port under any other circumstances.
( 除使用傳輸模式時，在其他環境下請勿打開保護蓋。)
扭力值
P (峰值保持模式)
T (追蹤模式)
歸零鈕 向下鈕
向上鈕
目錄鈕
單位 (N.m, in.lb, ft.lb, kg.cm)
電池使用相關訊息
1.
2.
3.
4.
5.
6.
7.
若長時間不使用本品，請將電池取下。
若使用於長途旅程或是位於寒冷地區，請多準備
備用電池。
請勿將新與舊的電池混合使用。
汗水、油污都會使電池加速老化，為避免此情形
發生，請於裝入電池前將電池擦拭乾淨。
請依照當地法規回收舊電池，請勿將電池丟入火中。
本品可使用標準或充電電池。
若螢幕畫面無法顯示，請檢查電池是否沒電，必要時
請加以更換。
AAA 電池 (R03UG 1.5V)
(內附兩顆 TOSHIBA 電池)
弱電顯示
Accuracy
Max. Operation Range
Alarm Setting Range
Resolution
Operation Mode
Unit Selection
Head Type
Gear Teeth
Key
Battery
Battery Life (Continuous operation)
Operating Temperature
Storage Temperature
Water Resistant Level
MODEL
CW: 3% CCW: 4%
80.00 N-m
4.00-80.00 N-m
0.01 N-m / 0.1 in-lb / 0.01 ft-lb / 0.1 kg-cm
Peak Hold Mode/ Track Mode / / / 峰值保持模式/追蹤模式
N-m/ in-lb/ ft-lb/ kg-cm
Lever type Ratchet / / /
60
4
AAA x 2 pc (included) / /
48 hrs. / / / 48小時
-10˚C - 60˚C
-20˚C - 70˚C
IPX-4 / /
SPECIFICATIONS / / /
規格
準確率
最大扭力值
警示音設定範圍
最低單位值
操作模式
單位選擇
轉動方向
棘輪齒數
按鈕
電池規格
電池使用時間 (連續使用狀態)
操作溫度範圍
收納溫度範圍
防水等級
對應名稱
棘輪方向撥桿
2-year Warranty: All mechanical components against manufacturer defects only.
Warranty Claim Requirements
To obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the
warranty begins on the date of manufacture. All warranties will be void if the product is damaged due to user crash, abuse, system
alteration, modification, or used in any way not intended as described in this manual.
* The specifications and design are subject to change without notice.
Please contact your Topeak dealer with any questions.
For USA customer service call: 1-800-250-3068
www.topeak.com
WARRANTY
3mm 4mm T256mm T30 T40
Bit Adaptor 10mm 9mm12mm 11mm 8mm
13mm15mm 14mm
8mm 10mm5mm
Sockets included / / / 內附套筒規格
Wrenches included / / / 內附工具規格
Philip #2
1/2” Drive
Adapter
保固要求
申請保固期限中的服務，須檢具原購買時之發票，若無法提供，則其保固期限將自製造日期開始算起。若因使用者不慎摔壞、使用不當、自行改裝、
更改系統或未能按照說明書上的正確操作方式，本產品將不被列入保固範圍。
* 本公司保留產品規格變更之權利。
Topeak產品相關的資訊，請洽詢Topeak當地授權的經銷商
網址：www.topeak.com
•
•
•
GB JKR CH
D-TORQ WRENCH DX USER'S GUIDE
The maximum operating torque range of the
wrench is 80 Nm. NEVER exceed 105% of its
maximum torque range (84 Nm) or it may
cause tool breakage and/or loss of accuracy.
Do not violently shake or drop the wrench.
Do not use this wrench as a hammer.
Do not leave this wrench in any place
exposed to excessive heat, humidity, or direct
sunlight.
Do not use this apparatus near water.
If the wrench gets wet, wipe it with a dry
towel as soon as possible. The salt in
seawater can be especially damaging.
Do not use organic solvents, such as alcohol
or paint thinner when cleaning the wrench.
Keep this wrench away from magnets.
Do not expose this wrench to dust or sand as
this could cause serious damage.
Do not apply excessive force to the LCD panel.
The alarm will sound at 100% maximum
setting torque.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
IMPORTANT NOTE /
/
/
重要提醒
In Track Mode / / / 追蹤模式時
(System initial)
Buzzer
Show Max. Target Value
2 Sec In Track Mode In Peak Hold Mode In Communication Mode
Pre-setting Unit: N-m
Max. Torque Value Reach Max. Torque ValueTorque value increasing Show new Torque value
press
Sending Message
WARNING / / /
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
本產品最大扭力值為80 Nm，若超過扭力值（最大扭力範圍的
105%，即84 Nm）， 可能會造成工具的損壞或使數據值產生
誤差。
請勿劇烈搖晃或摔落本品。
請勿使用榔頭敲擊本品。
請勿將本品置於高熱、潮濕的地方或是直接曝曬於陽光下。
請勿將本品置於水邊。
若不慎弄溼，請立即用乾布擦拭乾淨。
請勿使用有機溶劑來清潔本品，例如酒精或油漆稀釋劑。
請遠離磁鐵。
請勿將本品暴露充滿灰塵或風沙的環境下，如此可能造成裝
置嚴重的損壞。
請勿於LCD螢幕上施加過度的力量。
蜂鳴警示聲將會在100% 達到預設最大扭力值時發出聲響。
STEP 1: MODE SELECTION / / /
步驟一：模式選擇
SET UP / / /
設定
STEP 2: UNIT SELECTION / / /
步驟二：單位選擇
STEP 3: MAX. TORQUE VALUE SETTING / / /
步驟三：最大扭力值設定
WRENCH OPERATION / / /
如何使用扭力扳手
press
按壓 2秒
嗶嗶聲
進入追蹤模式 進入峰值保持模式 進入傳輸模式 傳送訊息
按壓
預設單位: N-m
to increase Max. torque value
增加最大扭力值
to decrease Max. torque value
減少最大扭力值
• Communication is for calibration of torque wrench. One
year
periodic recalibration is recommended to maintain
accuracy.
• DO NOT open port under any other circumstances.
• If no button is pressed in 2 minutes, D-Torq DX will shift
to auto sleep mode. Press C to resume normal operation.
NOTE / / /
注意
• 傳輸模式是用於校正扭力扳手的數值。
建議一年一次，定期作傳輸校正，以維持正確的數據值。
• 在其他環境下請勿打開保護蓋。
• 若於兩分鐘沒有按壓任何按鈕，本品將自動進入睡眠模式。
按壓 C 即可重新回到正常操作模式。
(系統啟動)
Apply Torque
施力
顯示預設最大扭力值 達到預設最大扭力值扭力值增加中 顯示目前扭力值
顯示預設最大扭力值
固定逆時針方向為鎖固 固定順時針方向為鎖固
按壓按鈕以安裝或
拆卸轉接頭
press
按壓
press
按壓
press
按壓
RESET WRENCH / / /
重設扭力扳手
Press C and simultaneously to
reset wrench. If the wrench does not
work properly, reset the wrench by
pressing C and at the same time.
同時按壓 與 即可重新設定扭力扳手。
若本品無法正常運作，請同時按壓 與 即可重新設定。
press
按壓
Apply Torque
施力
Buzzer
嗶嗶聲
Copyright © Topeak, Inc. 2018 M-TT2531-ML-2 04/ 18
Clockwise
Locked
Counter-clockwise
Locked
Press the release button
to mount or release the
adaptor.
3/8” square drive adapter for use with bits
3/8”工具轉接套筒
1/2” square drive adapter for use
with freewheel, cassette lockring
and bottom bracket tools
1/2” 飛輪工具、五通工具轉接套筒
Click
•
If is displayed, the wrench as been over-torqued.
The safe maximum operating torque is 80 Nm. Never
exceed 105% of its safe maximum torque (84 Nm) or tool
damage and/or loss of accuracy will occur
.
• STOP applying torque immediately when the audible alarm
is heard.
• 螢幕出現 代表已經超過最大扭力值80 Nm，若超過扭
力值（最大扭力範圍的105%，即84 Nm），可能會造成工具損壞
或使數據值產生誤差。
• 當聽到警示聲時，請立即停止操作。
CAUTION / / /
特別注意
•
•
USER'S GUIDE D-TORQ WRENCH DX USER'S GUIDE
•
화면에 이 표시되면 현재 렌치 한계 토크를 넘은
상태입니다. 렌치의 최대 작동 토크는 80Nm이며, 절대로 최대
작동 토크의 105%인 84Nm를 초과하지 마십시오. 그렇지
않으면 공구 손상 및 정확성의 손실이 발생하게 됩니다.
• 경보가 들리면 즉시 토크 작동을 중단합니다.
/