PowerVault MD1220

Dell PowerVault MD1220 クイックスタートガイド

  • こんにちは!Dell PowerVault MD1220 ストレージエンクロージャのクイックスタートガイドの内容を理解しています。このデバイスのセットアップ、機能、トラブルシューティングなど、ご質問にお答えします。このガイドには、システムの設置から電源接続、モード設定、そして追加情報へのアクセス方法まで、詳細な手順が記載されています。
  • システムの電源を入れる前に確認すべきことは何ですか?
    このエンクロージャは最大何台のハードドライブをサポートしますか?
    このエンクロージャはどのようなRAIDレベルをサポートしていますか?
    EMMとは何ですか?
Dell™ PowerVault™
MD1220 Storage Enclosures
Getting Started
With Your System
系统使用入门
Memulai Pengaktifan dengan Sistem Anda
はじめ
시스템 시작 안내서
Dell™ PowerVault™
MD1220 Storage Enclosures
Getting Started
With Your System
Regulatory Model Series E04J
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better
use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of
data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OpenManage, PowerEdge, and PowerVault are
trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
Regulatory Model Series E04J
August 2009 P/N J328M Rev. A00
Getting Started With Your System 3
Installation and Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with the system.
Unpacking the System
Unpack your system and identify each item.
Installing the Rails and System in a Rack
CAUTION: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma)
specified by the manufacturer. For more information, see "Technical
Specifications" on page 7.
Assemble the rails and install the system in the rack following the safety
instructions and the rack installation instructions provided with your system.
4 Getting Started With Your System
Connecting the Power Cable(s)
Ensure that the power switch is in the OFF position before connecting the
power cable(s). Connect the system’s power cable(s) to the system.
Securing the Power Cable(s)
Bend the system power cable(s) as shown in the illustration and secure the
cable(s) firmly to the bracket using the provided strap.
Plug the other end of the power cable(s) into a grounded electrical outlet or a
separate power source such as an uninterrupted power supply (UPS) or a
power distribution unit (PDU).
Getting Started With Your System 5
Turning On the System
Press the power switch to the ON position. The power indicators should light.
NOTE: Ensure that the storage enclosure is connected to the server and the mode
switch is set to split or unified mode before turning on the system.
Installing the Optional Bezel
Install the bezel (optional).
6 Getting Started With Your System
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with your
system. Warranty information may be included within this document or as a
separate document.
The rack documentation included with your rack solution describes how
to install your system into a rack.
•The
Hardware Owner’s Manual
provides information about system
features and describes how to troubleshoot the system and install or
replace system components. This document is available online at
support.dell.com/manuals
.
Any media that ships with your system that provides documentation
and tools for configuring and managing your system, including those
pertaining to the operating system, system management software,
system updates, and system components that you purchased
with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
NOM Information (Mexico Only)
The following information is provided on the device described in
this document in compliance with the requirements of the
official Mexican standards (NOM):
Importer:
Model number: E04J
Supply voltage: 100–240 V CA
Frequency: 50/60 Hz
Current consumption: 8.6 A
Getting Started With Your System 7
Technical Specifications
Drives
SAS hard drives Up to 24 2.5-inch SAS hot-swappable hard
drives (3.0 Gbps and 6.0 Gbps)
Enclosure Management Modules (EMMs)
EMMs One or two hot-swappable modules with
temperature sensors and an audio alarm
Connectivity
Configurations Support for either of the following
configurations:
Unified mode for direct connectivity to
24 hard drives per enclosure.
Up to four daisy-chained storage
enclosures for a total of 96 hard drives
per controller port and 192 hard drives
per controller.
Maximum configuration of
two dual port controllers per server for
a total of 384 drives.
Redundant path connectivity provides
redundant data paths to each hard drive.
Redundant path configuration supports
up to four daisy-chained storage
enclosures for a total of 96 hard drives
per controller and up to 192 hard drives
per server.
Split mode with dual EMMs provides a
direct connectivity to drives 0 through 11
and a separate direct connectivity to
drives 12 to 23. Split mode configuration
does not support daisy-chaining or
redundant data paths.
8 Getting Started With Your System
Redundant Array of Independent Disks (RAID)
Controller Host-based RAID support using
PowerEdge™ RAID controller H800.
Management RAID management using
Dell OpenManage™ Server
Administrator 6.2 or later.
Back-Plane Board
Connectors
24 SAS hard-drive connectors
Two power supply/cooling fan
module connectors
Two sets of EMM connectors
One control panel connector for front LEDs
and enclosure mode switch
Sensors Two temperature sensors
Back-Panel Connectors (per EMM)
SAS connectors
One SAS IN connector for connection
to the host
One SAS OUT connector for expansion to
an additional enclosure
NOTE: SAS connectors are SFF-8086/SFF-8088
compliant.
Serial connector One 6-pin UART mini-DIN connector
NOTE: For engineering use only.
LED Indicators
Front panel
One two-color LED indicator for
system status
Two single-color LED indicators for
power and split mode
Hard-drive carrier
One single-color activity LED
One two-color LED status indicator
per drive
Getting Started With Your System 9
EMM Three two-color LED status indicators,
one each for the two EMM SAS ports and
one for the EMM status
Power supply/cooling fan Three LED status indicators for power supply
status, power supply/cooling fan fault status,
and AC status
Switch
System identification button Located on the front control panel.
This button is used to locate a system
within a rack.
Mode switch Located on the front control panel.
This switch is used to switch the system
between unified and split mode operation.
Power Supplies
AC power supply (per power supply)
Wattage
600 W
Voltage
100–240 VAC (8.6 A–4.3 A)
Heat dissipation
188 W
Maximum inrush current
Under typical line conditions and over the
entire system ambient operating range,
the inrush current may reach 55 A per
power supply for 10 ms or less.
Available Hard Drive Power (Per Slot)
Supported hard drive power
consumption (continuous)
Up to 1.2 A at +5 V
Up to 0.5 A at +12 V
EMM Power (Per Slot)
Maximum power consumed by EMM 14 W at +12 V
Maximum available power 100 W at +12 V
Maximum available power 1 W at +5 V (standby)
LED Indicators (continued)
10 Getting Started With Your System
Physical
Height 8.68 cm (3.41 inches)
Width 44.63 cm (17.57 inches)
Depth 54.90 cm (21.61 inches)
Weight (maximum configuration) 23.31 kg (51.4 lb)
Weight (empty) 8.61 kg (19 lb)
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see www.dell.com/environmental_datasheets.
Temperature
Operating
10° to 35°C (50° to 95°F) with a maximum
temperature gradation of 10°C per hour
NOTE: For altitudes above 2950 feet,
the maximum operating temperature
is derated 1ºF/550 ft.
Storage
–40° to 65°C (–40° to 149°F) with
a maximum temperature gradation
of 20°C per hour
Relative humidity
Operating
20% to 80% (noncondensing) with
a maximum humidity gradation
of 10% per hour
Storage
5% to 95% (noncondensing)
Maximum vibration
Operating
0.25 G at 3–200 Hz for 15 min
Storage
0.5 G at 3–200 Hz for 15 min
Getting Started With Your System 11
Maximum shock
Operating
One shock pulse in the positive z axis
(one pulse on each side of the system) of
31 G for 2.6 ms in the operational orientation
Storage
Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system) of
71 G for up to 2 ms
Altitude
Operating
–16 to 3048 m (–50 to 10,000 ft)
NOTE: For altitudes above 2950 feet,
the maximum operating temperature is
derated 1ºF/550 ft.
Storage
–16 to 10,600 m (–50 to 35,000 ft)
Airborne Contaminant Level
Class
G2 or lower as defined by ISA-S71.04-1985
Environmental (continued)
12 Getting Started With Your System
Dell™ PowerVault™
MD1220 存储机柜
系统使用入门
管制模型系列 E04J
注、小心和警告
注:“注”表示可以帮助您更好地使用计算机的重要信息。
小心:“小心”表示如果不遵循说明,就有可能损坏硬件或导致数据丢失。
警告:“警告”表示可能会导致财产损失、人身伤害甚至死亡。
____________________
本说明文件中的信息如有更改,恕不另行通知。
© 2009 Dell Inc. 版权所有,翻印必究。
未经 Dell Inc. 书面许可,严禁以任何形式复制这些材料。
本文中使用的商标DellDELL 徽标、OpenManagePowerEdge PowerVault Dell Inc.
的商标。
本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的产
品。 Dell Inc. 对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。
管制模型系列 E04J
2009 8 P/N J328M 修订版 A00
系统使用入门 15
安装和配置
警告: 执行下列步骤之前,请阅读系统随附的安全说明。
打开系统包装
打开系统包装并识别每件物品。
在机架中安装滑轨和系统
小心:如果安装在封闭的或多单元机架部件中,机架周围的操作环境温度
可能高于室温。所以,应当考虑将设备安装在与制造商指定的最高环境温度
TMA)兼容的环境中。有关详情,请参阅第 19 页上的 技术规格
遵循系统随附的安全说明和机架安装说明在机架中组装滑轨并安装系统。
16 系统使用入门
连接电源电缆
在连接电源电缆之前确保电源开关处于关闭位置。将系统的电源电缆连接
到系统上。
固定电源电缆
如图所示,将系统电源电缆弯曲成一个环路,并使用所提供的带子将其固
定到支架。
将电源电缆的另一端插入接地的电源插座或单独的电源,如不间断电源设
UPS 或配电装置 PDU)。
系统使用入门 17
开启系统
按下电源开关至开启位置。电源指示灯将会亮起。
注:在开启系统之前确保存储机柜连接到服务器并且模式开关设置为分割
或统一模式。
安装可选挡板
安装挡板 (可选)
18 系统使用入门
可能需要的其它信息
警告:请参阅系统附带的安全与管制信息。保修信息可能包括在该说明文
件中,也可能作为单独的说明文件提供。
机架解决方案附带机架说明文件,介绍了如何将系统安装到机架中。
《硬件用户手册》提供了有关系统功能的信息,并说明了如何排除系统
故障以及安装或更换系统组件。可在
support.dell.com/manuals
在线获
取该说明文件。
系统随附的所有介质都提供了用于配置和管理系统的说明文件和工具,
包括与随系统购买的操作系统、系统管理软件、系统更新软件以及系
统组件相关的说明文件和工具。
注:请经常访问 support.dell.com/manuals 以获得更新,并首先阅读这
些更新,因为这些更新通常会取代其它说明文件中的信息。
NOM 信息 (仅限于墨西哥)
本说明文件中述及的符合墨西哥官方标准 NOM 要求的设备上均提供
以下信息:
进口商:
Dell Inc. de México, S.A. de C.V.
Paseo de la Reforma 2620 -11° Piso
Col. Lomas Altas
11950 México, D.F.
型号:
E04J
电源电压:
100–240 V CA
频率:
50/60 Hz
电流消耗:
8.6 A
/