ページを読み込んでいます...
1
2
3
SID 4-22
en Originaloperatinginstructions....................................... 1
da Originalbrugsanvisning .......................................... 11
sv Originalbruksanvisning........................................... 22
no Originalbruksanvisning .......................................... 32
fi Alkuperäisetohjeet ............................................. 43
et Originaalkasutusjuhend .......................................... 53
lv Oriģinālālietošanasinstrukcija ..................................... 64
lt Originalinaudojimoinstrukcija...................................... 75
ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 86
uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
tr Orijinalkullanımkılavuzu ......................................... 124
ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 136
ja オリジナル取扱説明書 ............................................ 148
ko 오리지널사용설명서............................................. 158
zh 原始操作說明.................................................. 168
cn 原版操作说明.................................................. 178
*2351410* 2351410 English 1
Original operating instructions
1 Information about the operating instructions
1.1 About these operating instructions
• Read these operating instructions before the product is used or operated for the first time. This is a
prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in these operating instructions and on the product.
• Always keep the operating instructions with the product and make sure that the product is accompanied
by these operating instructions only, when the product is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used:
DANGER
DANGER !
▶Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING
WARNING !
▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
CAUTION !
▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the
equipment or other property.
1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:
Comply with the operating instructions
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
Hilti Liion battery
Hilti charger
1.2.3 Symbols in illustrations
The following symbols are used in illustrations:
These numbers refer to the illustrations at the beginning of these operating instructions.
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text.
Item reference numbers are used in the overview illustration and refer to the numbers used in
the key in the product overview section.
These characters are intended to specifically draw your attention to certain points when handling
the product.
2 English 2351410 *2351410*
1.3 Product-dependent symbols
1.3.1 Additional symbols
The following symbols can be used additionally in this documentation or on the product:
The product supports near-field communication (NFC) technology compatible with iOS and
Android platforms.
Rated speed under no load
Direct current (DC)
Revolutions per minute
Forward / reverse
Li-ion battery
Never use the battery as a striking tool.
Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any
other way.
1.4 Product information
products are designed for professional users and only trained, authorized personnel are
permitted to operate, service and maintain the products. This personnel must be specifically informed about
the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by
untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
▶Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Impact wrench SID 4-22
Generation 02
Serial no.
1.5 Declaration of conformity
The manufacturer declares, on his sole responsibility, that the product described here complies with the
applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this
documentation.
The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
*2351410* 2351410 English 3
Electrical safety
▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a
dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
▶If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
▶Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
4 English 2351410 *2351410*
Battery tool use and care
▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Safety warnings for screwdrivers and impact wrenches
▶Hold the power tool by insulated gripping surfaces, when performing an operation where the
fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions
▶Use the product and accessories only when they are in perfect working order.
▶Never tamper with or modify the product or accessories in any way.
▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the product could give you an electric shock or cause an explosion if you
accidentally damage an electric cable or a gas or water pipe.
▶Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!
▶Avoid touching rotating parts – risk of injury!
▶Wear eye protection, a hard hat and ear protection while the product is in use.
▶Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in
cuts and burns.
▶Wear eye protection. Flying fragments present a risk of injury to the body and eyes.
▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some
examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone
and other products containing silicates; certain types of wood, such as oak, beech and chemically
treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and
bystanders by means of the hazard classification of the materials to be worked. Implement the necessary
measures to restrict exposure to a safe level, for example by the use of a dust collection system or by
the wearing of suitable respiratory protection. The general measures for reducing exposure include:
▶working in an area that is well ventilated,
▶avoidance of prolonged contact with dust,
▶directing dust away from the face and body,
▶wearing protective clothing and washing exposed areas of the skin with water and soap.
▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High
vibration during long periods of work can lead to disorders of the blood vessels and nervous system in
the fingers, hands and wrists.
▶Do not look directly into the light source (LED) of the product and do not aim the beam at other persons’
faces. Risk of dazzling or eye damage.
▶Switch the product on only after you have brought it to the working position.
*2351410* 2351410 English 5
▶Wait until the product has come to a complete stop before you lay it down.
▶Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed
accessories are secure.
2.4 Careful handling and use of batteries
▶Comply with the following safety instructions for the safe handling and use of Li-ion batteries.
Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶Use only batteries that are in perfect working order.
▶Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely
harmful to health!
▶Do not under any circumstances modify or tamper with batteries!
▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
▶Never use or charge a battery that has suffered an impact or been damaged in any other way. Check
your batteries regularly for signs of damage.
▶Never use recycled or repaired batteries.
▶Never use the battery or a battery-operated power tool as a striking tool.
▶Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This
can lead to explosions.
▶Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.
This can damage the battery and also cause material damage and personal injury.
▶Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,
electric shock, burns, fire and explosions.
▶Use only chargers and power tools approved for the specific battery type. Read and follow the relevant
operating instructions.
▶Do not use or store the battery in explosive environments.
▶If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to
cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the
document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
→ page 10
Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning
the QR code at the end of these operating instructions.
3 Description
3.1 Product overview 1
@Tool holder (1/4″ hex socket) with locking
sleeve
;Work-area light (LED)
=Forward/reverse switch with switch-on inter-
lock
%Control switch (with electronic speed control)
&Grip
(Installation opening for accessories
)Battery
+Battery release button
§Battery status indicator
3.2 Intended use
The product described is a hand-held cordless impact wrench. It is designed for driving and removing
screws and for tightening and releasing nuts and bolts in wood, metal, masonry and concrete.
6 English 2351410 *2351410*
• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance,
Hilti recommends the batteries stated in the table at the end of these operating instructions for this
product.
• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these
operating instructions.
3.3 Items supplied
Impact wrench, operating instructions
Other system products approved for use with this product can be found at your local Hilti Store or at:
www.hilti.group
3.4 Status indicators of the Liion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.
3.4.1 Indicators for state of charge and fault messages
WARNING
Risk of injury by a falling battery!
▶If the release button is pressed with a battery inserted in the product, subsequently check that the battery
is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following status indications is applicable
at the time.
State of charge and, if applicable, faults are indicated constantly as long as the connected product is
switched on.
Status Meaning
Four (4) LEDs show constantly green State of charge: 100 % to 71 %
Three (3) LEDs show constantly green State of charge: 70 % to 51 %
Two (2) LEDs show constantly green State of charge: 50 % to 26 %
One (1) LED shows constantly green State of charge: 25 % to 10 %
One (1) LED slow-flashes green State of charge: < 10 %
One (1) LED quick-flashes green The Li-ion battery is completely discharged.
Recharge the battery.
If the LED again starts quick-flashing after the bat-
tery has been charged, consult Hilti Service.
One (1) LED quick-flashes yellow The Li-ion battery or the product in which it is in-
serted is overloaded, too hot or too cold, or experi-
encing some other fault.
Bring the product and the battery to the recom-
mended working temperature and do not overload
the product when it is in use.
If the message persists, consult Hilti Service.
One (1) LED shows yellow The Li-ion battery and the product in which it is
inserted are not compatible. Consult Hilti Service.
One (1) LED quick-flashes red The Li-ion battery is locked and cannot be used.
Consult Hilti Service.
3.4.2 Indicators showing the battery's state of health
To check the battery's state of health, press the release button and hold it down for longer than three
seconds. The system does not detect a potential malfunction of the battery due to misuse, for example
battery dropped or pierced, external heat damage, etc.
Status Meaning
All LEDs show in sequence, followed by one (1)
LED showing constantly green. The battery can remain in use.
*2351410* 2351410 English 7
Status Meaning
All LEDs show in sequence, followed by one (1)
LED quick-flashing yellow. The check to ascertain the battery's state of health
did not complete. Repeat the procedure, or consult
Hilti Service.
All LEDs show in sequence, followed by one (1)
LED showing constantly red. If a connected product can still be used, the re-
maining battery capacity is below 50 %.
If a connected product can no longer be used, the
battery has reached the end of its useful life and
has to be replaced. Consult Hilti Service.
4 Technical data
Rated voltage 21.6 V
Weight in accordance with EPTA procedure 01, without battery 0.85 kg
Rated speed under no load 3,000 /min
Impact speed ≤ 4,400 bpm
Large standard bolts M8 to M16
Large high-strength bolts M6 to M12
Tool holder ¹⁄₄" hex socket with
locking sleeve
Storage temperature −20 ℃ … 70 ℃
Ambient temperature for operation −17 ℃ … 60 ℃
4.1 Battery
Battery operating voltage 21.6 V
Weight, battery See the end of these operating
instructions
Ambient temperature for operation −17 ℃ … 60 ℃
Storage temperature −20 ℃ … 40 ℃
Battery charging starting temperature −10 ℃ … 45 ℃
4.2 Noise information and vibration values in accordance with EN 62841
The sound pressure and vibration values given in these instructions were measured in accordance with a
standardized test and can be used to compare one power tool with another. They can also be used for a
preliminary assessment of exposure.
The data given represent the main applications of the power tool. However, if the power tool is used for
different applications, with different accessory tools, or is poorly maintained, the data can vary. This can
significantly increase exposure over the total working period.
An accurate estimation of exposure should also take into account the times when the tool is switched off, or
when it is running but not actually being used for a job. This can significantly reduce exposure over the total
working period.
Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for
example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work
patterns.
Noise information
Sound (power) level (L WA)103 dB
Uncertainty for the sound pressure level (K pA)3 dB
Emission sound pressure level (L pA)92 dB
Uncertainty for the sound power level (K WA)3 dB
8 English 2351410 *2351410*
Total vibration
Vibration emission value when tightening fasteners of the
maximum permitted size (ah)B 2255 10.7 m/s²
B 22255 12.1 m/s²
Uncertainty for tightening screws/bolts and nuts of the maximum permit-
ted size 1.5 m/s²
5 Preparations at the workplace
WARNING
Risk of injury by inadvertent starting!
▶Before inserting the battery, make sure that the product is switched off.
▶Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 5
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release button.
2. Remove the battery from the product.
5.4 Changing the accessory tool 2
CAUTION
Risk of injury by the accessory tool! The accessory tool might be hot or have sharp edges.
▶Wear protective gloves when changing the accessory tool.
1. Check that the connection end of the accessory tool is clean. Clean the connection end if necessary.
2. To insert the accessory tool push it into the tool holder as far as it will go, until the locking sleeve engages
with an audible click. Check that the accessory tool is held securely.
3. To remove the accessory tool, pull the locking sleeve forward and hold it in this position.
4. Pull the accessory tool out of the tool holder and release the locking sleeve.
5.5 Fall arrest
WARNING
Risk of injury by falling tool and/or accessory!
▶Use only the Hilti tool tether recommended for your product.
▶Prior to each use, always check the attachment point of the tool tether for possible damage.
▶Do not secure a tool tether to the belt hook. Do not use a belt hook to lift the product.
*2351410* 2351410 English 9
Comply with the national regulations for working at heights.
As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether
#2261970.
▶Secure the retaining strap to the installation openings for accessories. Check that it holds securely.
▶Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a
load-bearing structure. Check that both carabiners hold securely.
Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.
6 Operation
Observe the safety instructions and warnings in this documentation and on the product.
6.1 Setting forward or reverse rotation 3
▶Set the forward/reverse switch to the desired direction of rotation.
▶The control switch is locked when the forward/reverse switch is in the middle position (switch-on
interlock). An interlock prevents switching while the motor is running.
6.2 Switching on and off
1. Press the control switch.
▶The product starts.
Speed can be controlled steplessly by varying how far the control switch is pressed in.
2. Release the control switch.
▶The product switches off.
7 Care and maintenance
WARNING
Risk of injury with battery inserted !
▶Always remove the battery before carrying out care and maintenance tasks!
Care of the product
• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of
moisture (e.g. by being dipped in water or left in the rain).
If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable
container and consult Hilti Service.
• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily
on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents
containing silicone as these can attack the plastic parts.
Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
10 English 2351410 *2351410*
Maintenance
• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly.
• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product
repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices and check that they are in full
working order.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with your product can be found at your
Hilti Store or online at: www.hilti.group
8 Transport and storage of cordless tools and batteries
Transport
CAUTION
Accidental starting during transport !
▶Always transport your products with the batteries removed!
▶Remove the battery/batteries.
▶Never transport batteries loose and unprotected. During transport, batteries should be protected from
excessive shock and vibration and isolated from any conductive materials or other batteries that may
come in contact with the terminals and cause a short circuit. Comply with the locally applicable
regulations for transporting batteries.
▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged
batteries.
▶Prior to each use and before and after prolonged transport, check the product and the batteries for
damage.
Storage
WARNING
Accidental damage caused by defective or leaking batteries !
▶Always store your products with the batteries removed!
▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in
the technical data.
▶Do not store batteries on the charger. Always remove the battery from the charger when the charging
operation has completed.
▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.
▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.
▶Prior to each use and before and after prolonged storage, check the product and the batteries for
damage.
9 Troubleshooting
If a problem occurs, always observe the charge-status and fault indicator of the battery. See the section
headed Status indicators of the Liion battery.
If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by
yourself, contact Hilti Service.
Trouble or fault Possible cause Action to be taken
Product does not work. The battery is not fully inserted. ▶Push the battery in until it
engages with an audible click.
Running speed suddenly
drops considerably. Battery is discharged. ▶Change the battery and charge
the empty battery.
The battery runs down more
quickly than usual. Very low ambient temperature. ▶Allow the battery to warm up
slowly to room temperature.
The battery does not engage
with an audible click. The retaining lugs on the battery
are dirty.
▶Clean the retaining lugs and
engage the battery in the
working position.
*2351410* 2351410 Dansk 11
Trouble or fault Possible cause Action to be taken
Product or battery gets very
hot. Electrical fault. ▶Switch the product off immedi-
ately, remove the battery, keep
it under observation, allow it
to cool down and contact Hilti
Service.
LEDs of the battery show
nothing Battery defective. ▶Contact Hilti Service.
10 Disposal
WARNING
Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.
▶DO NOT send batteries through the mail!
▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
▶Dispose of your battery out of the reach of children.
▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public
health and safety resources for disposal instructions.
Most of the materials from which Hilti products are manufactured can be recycled. The materials must be
correctly separated before they can be recycled. In many countries, your old tools, machines or appliances
can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.
▶Do not dispose of power tools, electronic equipment or batteries as household waste!
11 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about the warranty conditions.
12 Further information
For more information on operation, technology, environment and recycling, follow this link:
qr.hilti.com/manual?id=2321973&id=2351410
This link is also to be found at the end of the documentation, in the form of a QR code.
Original brugsanvisning
1 Om brugsanvisningen
1.1 Om denne brugsanvisning
• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde
og korrekt håndtering.
• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.
• Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer
sammen med denne brugsanvisning.
1.2 Tegnforklaring
1.2.1 Advarsler
Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:
FARE
FARE !
▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.
12 Dansk 2351410 *2351410*
ADVARSEL
ADVARSEL !
▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.
FORSIGTIG
FORSIGTIG !
▶Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.
1.2.2 Symboler i brugsanvisningen
Der benyttes følgende symboler i denne brugsanvisning:
Se brugsanvisningen
Anvisninger for anvendelse og andre nyttige oplysninger
Håndtering af genvindbare materialer
Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald
Hilti Lithium-ion-batteri
Hilti Lader
1.2.3 Symboler i illustrationer
Følgende symboler anvendes på illustrationer:
Disse tal henviser til den pågældende illustration i begyndelsen af denne brugsanvisning.
Nummereringen udtrykker arbejdstrinnenes rækkefølge på illustrationen og kan afvige fra arbejds-
trinnene i teksten.
Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i
afsnittet Produktoversigt.
Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.
1.3 Produktspecifikke symboler
1.3.1 Yderligere symboler
Følgende symboler kan også forekomme i denne dokumentation og på produktet:
Produktet understøtter NFC-teknologi, som er kompatibel med iOS- og Android-platforme.
Nominelt omdrejningstal ubelastet
Jævnstrøm
Omdrejninger pr. minut
Højre-/venstreløb
Li-ion-batteri
Brug aldrig batteriet som slagværktøj.
Lad ikke batteriet falde på gulvet. Brug ikke et batteri, der har fået et slag eller på anden vis er
beskadiget.
*2351410* 2351410 Dansk 13
1.4 Produktoplysninger
-produkter er beregnet til professionel brug og må kun betjenes, efterses og vedligeholdes af
autoriseret og instrueret personale. Dette personale skal i særdeleshed informeres om de potentielle farer,
der er forbundet med anvendelsen af denne maskine. Der kan opstå farlige situationer ved anvendelse af
produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke er blevet undervist i dens brug,
eller hvis det ikke anvendes korrekt i henhold til forskrifterne i denne brugsanvisning.
Typebetegnelse og serienummer fremgår af typeskiltet.
▶Notér serienummeret i den efterfølgende tabel. Du skal bruge produktoplysningerne ved henvendelser til
vores lokale afdeling eller vores serviceværksted.
Produktoplysninger
Slagskruemaskine SID 4-22
Generation 02
Serienummer
1.5 Overensstemmelseserklæring
Producenten erklærer som eneansvarlig, at det her beskrevne produkt er i overensstemmelse med gældende
lovgivning og gældende standarder. Sidst i dette dokument finder du et bilede af overensstemmelseserklæ-
ringen.
Den tekniske dokumentation er arkiveret her:
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2 Sikkerhed
2.1 Generelle sikkerhedsanvisninger for elværktøj
ADVARSEL Læs alle sikkerhedsanvisninger, henvisninger, billedtekster og tekniske data på
elværktøjet. Hvis følgende anvisninger ikke overholdes, er der risiko for elektrisk stød, brand og/eller
alvorlige personskader.
Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.
Det benyttede begreb "elværktøj" i sikkerhedsanvisningerne refererer til elektriske maskiner (med netledning)
eller batteridrevne maskiner (uden netledning).
Arbejdspladssikkerhed
▶Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden eller uoplyste arbejdsområder
øger faren for uheld.
▶Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er brændbare væsker, gasser eller
støv. Elværktøj kan slå gnister, der kan antænde støv eller dampe.
▶Sørg for, at andre personer og ikke mindst børn holdes væk fra arbejdsområdet, når elværktøjet
er i brug. Hvis man distraheres, kan man miste kontrollen over maskinen.
Elektrisk sikkerhed
▶Elværktøjets stik skal passe til kontakten. Stikket må under ingen omstændigheder ændres. Brug
ikke adapterstik sammen med jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,
nedsætter risikoen for elektrisk stød.
▶Undgå kropskontakt med jordforbundne overflader som f.eks. rør, radiatorer, komfurer og
køleskabe. Hvis din krop er jordforbundet, øges risikoen for elektrisk stød.
▶Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand i elværktøj øger risikoen for
elektrisk stød.
▶Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må man aldrig bære elværktøjet i
ledningen, hænge det op i ledningen eller rykke i ledningen for at trække stikket ud af kontakten).
Beskyt ledningen mod varme, olie, skarpe kanter eller dele, der er i bevægelse. Beskadigede eller
sammenviklede ledninger øger risikoen for elektrisk stød.
▶Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlængerledning, der er egnet til
udendørs brug. Brug af forlængerledning til udendørs brug nedsætter risikoen for elektrisk stød.
▶Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser, skal du anvende et
fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ nedsætter risikoen for et elektrisk stød.
14 Dansk 2351410 *2351410*
Personlig sikkerhed
▶Det er vigtigt at være opmærksom, se, hvad man laver, og bruge maskinen fornuftigt. Anvend aldrig
elværktøj, hvis du er træt eller påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed
under brugen af elværktøjet kan medføre alvorlige personskader.
▶Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af sikkerhedsudstyr som f.eks.
støvmaske, skridsikkert fodtøj, beskyttelseshjelm eller høreværn afhængigt af elværktøjets type og
anvendelse nedsætter risikoen for personskader.
▶Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er frakoblet, før du slutter det til
strømforsyningen og/eller batteriet, tager det op eller transporterer det. Undgå at bære elværktøjet
med fingeren på afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da dette øger
risikoen for personskader.
▶Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tændes. Hvis et stykke værktøj eller en
nøgle sidder i en roterende maskindel, er der risiko for personskader.
▶Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert, mens der arbejdes, og kom
ikke ud af balance. Det er derved nemmere at kontrollere elværktøjet, hvis der skulle opstå uventede
situationer.
▶Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller smykker. Hold hår, tøj og handsker
væk fra dele, der bevæger sig. Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller
langt hår.
▶Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det vigtigt, at dette tilsluttes og
benyttes korrekt. Ved at anvende en støvudsugning er det muligt at nedsætte risiciene som følge af
støv.
▶Man må ikke ignorere sikkerhedsreglerne for elværktøj, heller ikke selvom man er fortrolig med
brugen af elværktøjet. Uagtsomhed kan medføre alvorlig tilskadekomst inden for få sekunder.
Anvendelse og pleje af elværktøjet
▶Undgå at overbelaste maskinen. Brug altid en maskine, der er beregnet til det stykke arbejde,
der skal udføres. Med det rigtige værktøj arbejder man bedst og mest sikkert inden for det angivne
effektområde.
▶Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke kan startes og stoppes, er farlig
og skal repareres.
▶Træk stikket ud af stikkontakten, og/eller fjern batteriet fra maskinen, inden du foretager
indstillinger på den, skifter tilbehør og dele eller lægger den til side. Disse sikkerhedsforanstaltninger
forhindrer utilsigtet start af elværktøjet.
▶Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad aldrig personer, der ikke er
fortrolige med maskinen eller ikke har gennemlæst sikkerhedsanvisningerne, benytte denne.
Elværktøj er farligt, hvis det benyttes af ukyndige personer.
▶Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige dele fungerer korrekt og
ikke sidder fast, og om delene er brækket eller beskadiget, således at elværktøjets funktion
påvirkes. Få beskadigede dele repareret, inden elværktøjet tages i brug. Mange uheld skyldes
dårligt vedligeholdte elværktøjer.
▶Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt vedligeholdte skæreværktøjer med
skarpe skærekanter sætter sig ikke så hurtigt fast og er nemmere at føre.
▶Anvend elværktøj, tilbehør, indsatsværktøj osv. i overensstemmelse med disse anvisninger. Tag
hensyn til arbejdsforholdene og det arbejde, der skal udføres. I tilfælde af anvendelse af maskinen til
formål, som ligger uden for det fastsatte anvendelsesområde, kan der opstå farlige situationer.
▶Sørg for, at greb og gribeflader er tørre, rene og fri for olie og fedt. Glatte greb og gribeflader gør
betjeningen usikker, og det kan være svært at styre elværktøjet i uforudsete situationer.
Anvendelse og pleje af batteridrevet elværktøj
▶Oplad kun batterier i ladere, der er anbefalet af fabrikanten. Der er risiko for brand, hvis en lader, der
er beregnet til et bestemt batteri, anvendes til opladning af en anden batteritype.
▶Brug kun de batterier, der er beregnet til elværktøjet. Brug af andre batterier øger risikoen for
personskader og er forbundet med brandfare.
▶Ikke benyttede batterier må ikke komme i berøring med kontorclips, mønter, nøgler, søm, skruer
eller andre små metalgenstande, da disse kan kortslutte kontakterne. En kortslutning mellem
batterikontakterne øger risikoen for personskader i form af forbrændinger.
▶Hvis batteriet anvendes forkert, kan der løbe væske ud af batteriet. Undgå at komme i kontakt
med denne væske. Hvis det alligevel skulle ske, skylles med vand. Søg læge, hvis væsken kommer
i øjnene. Batterivæske kan give hudirritation eller forbrændinger.
▶Brug aldrig et beskadiget eller ændret batteri. Beskadigede eller ændrede batterier kan virke utilsigtet
og medføre brand, eksplosion eller risiko for tilskadekomst.
*2351410* 2351410 Dansk 15
▶Batterier må ikke udsættes for åben ild eller høje temperaturer. Ild eller temperaturer over 130 °C
(265 °F) kan medføre eksplosion.
▶Følg alle anvisninger vedrørende opladning, og oplad aldrig batteriet eller det batteridrevne
værktøj uden for det temperaturområde, der er anført i betjeningsvejledningen. Forkert opladning
eller opladning uden for det tilladte temperaturområde kan ødelægge batteriet og øge risikoen for brand.
Service
▶Sørg for, at elværktøjet kun repareres af kvalificerede fagfolk, og at der altid benyttes originale
reservedele. Dermed sikres størst mulig elværktøjssikkerhed.
▶Forsøg aldrig at reparere beskadigede batterier. Al vedligeholdelse af batterier skal foretages af
producenten eller af autoriserede forhandlere.
2.2 Sikkerhedsanvisninger for skruemaskiner og slagskruemaskiner
▶Hold elværktøjet på de isolerede grebsflader, når du udfører opgaver, hvor skruen kan ramme
skjulte elledninger. Ved kontakt mellem skruen og en spændingsførende ledning kan også metalliske
værktøjsdele sættes under spænding, hvilket kan medføre elektrisk stød.
2.3 Yderligere sikkerhedsanvisninger
▶Anvend kun produktet og tilbehør i teknisk fejlfri stand.
▶Foretag aldrig manipulationer eller ændringer på produkt eller tilbehør.
▶Kontrollér før påbegyndelse af arbejdet arbejdsområdet for skjulte elektriske ledninger, gas- og vandrør,
f.eks. med en metaldetektor. Udvendige metaldele på produktet kan medføre elektrisk stød eller
forårsage en eksplosion, hvis r du beskadiger en elledning, et gasrør eller et vandrør.
▶Hold altid ventilationsåbningerne fri. Fare for forbrændinger på grund af tildækkede ventilationsåbninger!
▶Undgå berøring af roterende dele - fare for personskader!
▶Brug beskyttelsesbriller, sikkerhedshjelm og høreværn under brugen af produktet.
▶Brug beskyttelseshandsker, når du skifter værktøj. Berøring af indsatsværktøjet kan medføre snitsår og
forbrændinger.
▶Brug øjenværn. Splinterne fra materialet kan medføre skader på legeme og øjne.
▶Støv, der dannes ved slibning, skæring og boring, kan indeholde farlige kemikalier. Nogle eksempler er:
Bly eller maling på blybasis; Tegl, beton og andre murværksprodukter, natursten og andre silikatholdige
produkter; Bestemte træsorter som eg, bøg og kemisk behandlet træ; Asbest eller asbestholdige
materialer. Bestem eksponeringen for brugeren og omkringstående personer ved hjælp af fareklassen
for de materialer, der arbejdes på. Træf de nødvendige foranstaltninger for at holde eksponeringen på et
sikkert niveau, f.eks. ved at bruge et støvopsamlingssystem eller brug af et passende åndedrætsværn.
Generelle foranstaltninger til at reducere eksponeringen omfatter bl.a.:
▶Arbejde i et godt ventileret område,
▶Undgå længere tids kontakt med støv,
▶Lede støv bort fra ansigt og krop,
▶Bruge beskyttende beklædning og vaske eksponerede områder med vand og sæbe.
▶Hold hyppigt pauser, og lav øvelser, så fingrene får bedre blodgennemstrømning. Ved længerevarende
arbejde kan vibrationer medføre forstyrrelser af fingrenes, hændernes eller håndleddenes blodkar og
nervesystem.
▶Kig ikke direkte ind i produktets lampe (lysdiode), og lys ikke ind i ansigtet på andre personer. Der er fare
for at blive blændet.
▶Tænd først produktet, når du har bragt det i arbejdsposition.
▶Vent, indtil produktet er standset helt, før du lægger det fra dig.
▶Fare for personskader på grund af værktøj og/eller tilbehør, som falder på jorden. Kontrollér før arbejdets
begyndelse, at batteriet og det monterede tilbehør er sikkert fastgjort.
2.4 Omhyggelig omgang med og brug af batterier
▶Overhold følgende sikkerhedsforanstaltninger for sikker håndtering og brug af Li-ion-batterier.
I modsat fald kan det medføre hudirritation, alvorlige ætsningsskader, kemiske forbrændinger, brand
og/eller eksplosion.
▶Anvend kun batterier i teknisk fejlfri stand.
▶Batterier skal behandles forsigtigt for at undgå beskadigelser og udslip af meget sundhedsskadelige
væsker!
▶Batterier må under ingen omstændigheder modificeres eller manipuleres!
16 Dansk 2351410 *2351410*
▶Batterierne må ikke adskilles, klemmes, opvarmes til over 80 °C eller brændes.
▶Anvend og oplad ikke batterier, som har fået stød eller på anden vis er blevet beskadiget. Kontrollér
regelmæssigt dine batterier for tegn på skader.
▶Anvend aldrig genbrugte eller reparerede batterier.
▶Anvend aldrig batteriet eller et batteridrevet elværktøj som slagværktøj.
▶Udsæt aldrig batterier for direkte solstråling, høj temperatur, gnister eller åben ild. Det kan medføre
eksplosion.
▶Berør ikke batteripolerne med dine fingre, værktøj, smykker eller andre elektrisk ledende genstande. Det
kan beskadige batteriet og medføre personskader og materielle skader.
▶Hold batterier på sikker afstand af regn, fugt og væsker. Indtrængende fugt kan medføre kortslutninger,
elektrisk stød, forbrændinger, brand og eksplosion.
▶Brug kun ladere og elværktøj, der er beregnet til denne batteritype. Overhold i den forbindelse
oplysningerne i de tilhørende brugsanvisninger.
▶Anvend og opbevar ikke batteriet i eksplosionsfarlige omgivelser.
▶Hvis batteriet er for varmt til at kunne røres, kan det være defekt. Anbring batteriet på et overskueligt,
ikke-brændbart sted med tilstrækkelig afstand til brændbare materialer. Lad batteriet køle af. Hvis
batteriet efter en time fortsat er for varmt til at kunne røres, er det er defekt. Kontakt Hilti Service eller
læs dokumentet "Anvisninger om sikkerhed og anvendelse af Hilti Li-ion-batterier".
Vær opmærksom på de særlige retningslinjer, der gælder for transport, opbevaring og brug af Li-
ion- batterier. → Side 20
Læs anvisningerne vedrørende sikkerhed og anvendelse til Hilti Li-ion-batterier, som du kan finde
ved at scanne QR-koden sidst i denne brugsanvisning.
3 Beskrivelse
3.1 Produktoversigt 1
@Værktøjsholder (1/4″ indvendig sekskant) med
låsetylle
;Arbejdsområdebelysning (lysdiode)
=Omskifter til valg af højre-/venstreløb med
startspærre
%Afbryder (med elektronisk hastighedsstyring)
&Håndgreb
(Monteringsåbning til tilbehør
)Batteri
+Batterifrigørelsesknap
§Statusindikator for batteri
3.2 Bestemmelsesmæssig anvendelse
Det beskrevne produkt er en håndført, batteridrevet slagskruemaskine. Den er beregnet til at spænde og
løsne skruer, møtrikker og bolte med gevind i træ, metal, murværk og beton.
• Brug kun Hilti Nuron Liion-batterier i serie B 22 til dette produkt. For at opnå optimal effekt anbefaler
Hilti at bruge de batterier, der er anført i tabellen i slutningen af brugsanvisningen, til dette produkt.
• Anvend kun Hilti-ladere, der er anført i slutningen af denne brugsanvisning, til disse batterier.
3.3 Leveringsomfang
Slagskruemaskine, brugsanvisning
Andre systemprodukter, som er godkendt til dit produkt, finder du i Hilti Store eller på: www.hilti.group
3.4 Li-ion-batteriets indikatorer
Hilti Nuron Li-ion-batterier kan vise ladetilstand, fejlmeddelelser og batteriets tilstand.
/