Makita DUS108, DUS158 Cordless Garden Sprayer ユーザーマニュアル

DUS108 / DUS158

EN Cordless Garden Sprayer Instruction Manual 2

ZHCN 充电式喷雾器使用说明书 20

ZHTW 充電式噴霧機使用說明書 38

KO 충전 분무기 취급 설명서 56

ID Penyemprot Taman Tanpa Kabel

PETUNJUK PENGGUNAAN

74

MS Penyembur Taman Tanpa Kord MANUAL ARAHAN 92

VI 

  110

TH ตัวฉีดพ่นสวนไร้สาย ค่มู ือการใชง้ าน 128

AR   163

2English

English (Original instructions)

1 Vertical type 2-head nozzle 2 Spray wand 3 Tank lid 4 Tank (10 L/15 L)

5 Spray wand holder 6 Spray hose 7 Lever 8 Handle

9 Carrying straps 10 Locking lever 11 Battery cover 12 Back cushion

13 ON/OFF switch 14 Indicator lamps 15 Liquid outlet 16 Hook (for attaching

the spray wand)

17 Weedkiller nozzle - - - - - -

3English

SPECIFICATIONS

Model DUS108 DUS158

Rated voltage D.C. 18 V

Tank capacity 10 L 15 L

Hose length 1.7 m

Spray wand length 60 cm

Max. working pressure 0.5 MPa

Working pressure with vertical type

2-head nozzle Approx. 0.34 MPa

Flow rate with vertical type 2-head

nozzle Approx. 0.90 L/min

Working pressure with weedkiller

nozzle Approx. 0.12 MPa

Flow rate with weedkiller nozzle Approx. 1.70 L/min

Nozzle tting screw G 1/4"

Technical the volume of total residual ≤ 200 ml

Dimensions (L × W × H) 317 × 237 × 437 mm 317 × 237 × 517 mm

Weight when empty 5.6 - 5.9 kg 5.9 - 6.2 kg

Weight when full 15.6 - 15.9 kg 20.9 - 21.2 kg

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heaviest

combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / DC18SH

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

WARNING: Do not use a corded power supply such as battery adapter or portable power pack with

this machine. The cable of such power supply may hinder the operation and result in personal injury.

Symbols

The followings are symbols used for the equipment. Be sure that you understand their meaning before use.

Wear ear protection. Warning

Wear a breathing

mask. Wear eye protection.

Wear safety

footwear.

Wear protective

gloves.

Do not use in the rain or leave the sprayer outdoors

while raining.

Read instruction manual.

Keep bystanderds away when spraying.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous components in the

equipment, waste electrical and electronic equipment,

accumulators and batteries may have a negative

impact on the environment and human health.

Do not dispose of electrical and electronic appliances

or batteries with household waste!

In accordance with the European Directive on waste

electrical and electronic equipment and on accumula-

tors and batteries and waste accumulators and batter-

ies, as well as their adaptation to national law, waste

electrical equipment, batteries and accumulators

should be stored separately and delivered to a sep-

arate collection point for municipal waste, operating

in accordance with the regulations on environmental

protection.

This is indicated by the symbol of the crossed-out

wheeled bin placed on the equipment.

4English

Intended use

This machine is intended for spraying.

WARNING

This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experi-

ence and knowledge if they

have been given supervision

or instruction concerning use

of the appliance in a safe way

and understand the hazards

involved. Children shall not play

with the appliance. Cleaning

and user maintenance shall not

be made by children without

supervision.

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while oper-

ating a power tool. Distractions can cause you to

lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

7. Power tools can produce electromagnetic elds

(EMF) that are not harmful to the user. However,

users of pacemakers and other similar medical

devices should contact the maker of their device

and/or doctor for advice before operating this power

tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that

have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

5English

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

can cause severe injury within a fraction of a

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer’s responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the rate

for which it was designed.

2. Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

3. Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, break-

age of parts and any other condition that may

aect the power tool’s operation. If damaged,

have the power tool repaired before use. Many

accidents are caused by poorly maintained power

tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and the

work to be performed. Use of the power tool for

operations dierent from those intended could result

in a hazardous situation.

8. Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled. The entangle-

ment of cloth work gloves in the moving parts may

result in personal injury.

Battery tool use and care

1. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one

type of battery pack may create a risk of re when

used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another. Shorting the battery terminals together

may cause burns or a re.

4. Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in re,

explosion or risk of injury.

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instructions.

Charging improperly or at temperatures outside

the specied range may damage the battery and

increase the risk of re.

6English

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

3. Follow instruction for lubricating and changing

accessories.

Cordless Garden Sprayer

Safety Warnings

WARNING: Risk of re or explosion. Do not

spray ammable liquids such as gasoline. Look

for this symbol reference on the container.

WARNING: Some spray created from products

used with the sprayer contains chemicals known

to cause cancer, birth defect of other reproductive

harm.

Some examples of these chemicals are:

· compounds in fertilize.

· compounds in insecticides, herbicides, and pesticides;

· arsenic and chromium from chemically treated lumber.

Follow directions on containers of all such products.

To reduce your exposure to these chemicals, wear

approved safety equipment such as face masks that

are specially designed to filter out sprays, gloves, and

other appropriate protective equipment.

■ Before using any pesticide or other spray mate-

rials in this sprayer, read the label on its original

container thoroughly and follow its directions.

Some spray materials are dangerous and should

not be used in this sprayer, as they can damage the

sprayer and cause serious bodily injury or property

damage.

■ Electric shock hazard. Never spray toward electri-

cal outlets.

■ Do not use commercial grade chemicals or

chemicals for commercial or industrial pur-

poses. Use only consumer grade water-based lawn

and garden chemicals.

■ Do not pour hot or boiling liquids into the tank.

These can weaken or damage the hose or tank.

■ Spray area must be well ventilated.

■ Avoid spraying on windy days. Spray can be

accidentally blown onto plants or objects that should

not be sprayed.

■ Store the sprayer in a secure, well-ventilated

indoor space with the uid tank empty.

■ Do not use caustic (alkali) self-heating or cor-

rosive (acid) liquids in this sprayer. These can

corrode metal parts or weaken the tank and hose.

■ Wear respiratory protection and appropriate

protective clothing. Keep bystanders away when

spraying.

■ Know the contents of the chemical being

sprayed. Read all Material Safety Data Sheets

(MSDS) and container labels provided with the

chemical. Follow the chemical manufacturer’s

safety instructions.

■ Do not leave residue or spray material in the

tank after using the sprayer. Clean after each use.

■ Do not smoke while using the sprayer, or spray

where spark or ame is present.

■ Risk of injection. Do not discharge directly against

skin.

■ To reduce the risk of electric shock, do not put

the sprayer into water or other liquid. Do not

place or store the sprayer where it can fall or be

pulled into a tub or sink.

■ Maintain this product. Thoroughly inspect both

the inside and outside of the sprayer and exam-

ine the components before each use. Check for

cracked and deteriorated hoses, leaks, clogged

nozzles, and missing or damaged parts. If dam-

aged, have the product repaired before use.

Many accidents are caused by poorly maintained

products.

■ Disconnect the battery from the unit before

draining, cleaning, or storing the sprayer. Such

preventive safety measures reduce the risk of acci-

dental starting.

■ Always wear eye protection with side shields

or goggles marked to comply with ANSI Z87.1.

Failure to do so could result in uids entering your

eyes resulting in possible serious injury.

■ Protect your lungs. Wear a face or dust mask

when using the sprayer. Following this rule will

reduce the risk of serious personal injury.

■ Battery tools do not have to be plugged into

an electrical outlet; therefore, they are always

in operating condition. Be aware of possible

hazards when not using your battery tool or

when changing accessories. Remove battery

pack when tool is not in use. Following this rule

will reduce the risk of electric shock, re, or serious

personal injury.

■ Do not place battery tools or their batteries near

re or heat. This will reduce the risk of explosion

and possibly injury.

■ Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has been

dropped or received a sharp blow. A damaged

battery is subject to explosion. Properly dispose of a

dropped or damaged battery immediately.

■ Batteries can explode in the presence of a

source of ignition, such as a pilot light. To reduce

the risk of serious personal injury, never use any

cordless product in the presence of open ame. An

exploded battery can propel debris and chemicals. If

exposed, ush with water immediately.

■ Do not charge battery tool in a damp or wet

location. Following this rule will reduce the risk of

electric shock.

■

For best results, your battery tool should be

charged in a location where the temperature is

more than 10 °C (50 °F) but less than 40 °C (104 °F).

To reduce the risk of serious personal injury, do not

store outside or in vehicles.

7English

■ Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in

contact with your skin, wash immediately with

soap and water. If liquid gets into your eyes,

ush them with clean water for at least 10 min-

utes, then seek immediate medical attention.

Following this rule will reduce the risk of serious

personal injury.

■ Do not use battery-operated appliance in rain.

■ Exercise care in handling batteries in order not

to short the battery with conducting materials

such as rings, bracelets, and keys. The battery or

conductor may overheat and cause burns.

■ Do not dispose of the battery(ies) in a re. The

cell may explode. Check with local codes for possi-

ble special disposal instructions.

■ Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if

swallowed.

■ Avoid Dangerous Environment - Don’t use appli-

ances in damp or wet locations.

■ Use Right Appliance - Do not use appliance for

any job except that for which it is intended.

■ Don’ t Force Appliance - It will do the job better

and with less likelihood of a risk of injury at the rate

for which it was designed.

■ Store Idle Appliances Indoors - When not in use,

appliances should be stored indoors in dry, and high

or locked-up place - out of reach of children.

■ Maintain Appliance With Care - Keep clean for

best performance and to reduce the risk of injury.

Follow instructions for changing accessories.

Inspect appliance cord, and if damaged, have it

repaired by an authorized service facility. Keep

handles dry, clean, and free from oil and grease.

■ Check Damaged Parts - Before further use of the

appliance, a guard or other part that is damaged

should be carefully checked to determine that it will

operate properly and perform its intended function.

Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting, and any

other condition that may aect its operation. A guard

or other part that is damaged should be properly

repaired or replaced by an authorized service center

unless indicated elsewhere in this manual.

■ Don’t topple a lled-up tank to avoid leak in case

tank lid is not tightened.

Residual risks

Even if you use this electric power tool in

accordance with instructions, certain resid-

ual risks cannot be rules out. The following

hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective mask is used.

2. Contact with hazardous substances. Spray mate-

rials can be harmful if inhaled or swallowed or if

allowed to come into contact with the skin or eyes.

Follow the instructions and wear suitable protective

equipment.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery car-

tridge. It may result in a re, excessive heat, or

explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current ow, over-

heating, possible burns and even a breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties, for-

warding agents, special requirement on packaging

and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

8English

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe place.

Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products speci-

ed by Makita. Installing the batteries to non-com-

pliant products may result in a re, excessive heat,

explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low tem-

perature burns. Pay attention to the handling of

hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near high-volt-

age electrical power lines, do not use the

battery cartridge near high-voltage electrical

power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery ser-

vice life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let a

hot battery cartridge cool down before charging

it.

4. When not using the battery cartridge, remove it

from the tool or the charger.

5. Charge the battery cartridge if you do not use it

for a long period (more than six months).

9English

CORDLESS GARDEN SPRAYER USE AND CARE

1. The cordless garden sprayer can work by Makita lithium-ion battery cartridge. Use of any other batteries may

create a risk of re. Recharge batteries only with the specied charger. A charger that may be suitable for one type

of battery may create a risk of re when used with another battery.

2. When inserting or removing the battery, always place the cordless garden sprayer on a at and stable surface.

3. Do not use any batteries, attachments or accessories not recommended by the manufacturer of this appliance.

The use of batteries, attachments or accessories not recommended can result in serious personal injury.

Intended use

This pressure sprayer is designed exclusively for spraying the following solutions outdoors and in well ventilated

greenhouses.

● Water

● Pesticides

● Weedkillers

● Natural oils dissolved in water (e.g..neem oil, rapeseed oil).

● Fertilizers dissolved in water.

Liquids to be sprayed, particularly natural oils dissolved in water, must have a water-like consistency. Liquids of

greater viscosity cannot be sprayed, or only with lesser power.

Only liquid fertilizers, weedkillers and pesticides that are approved by the local licensing authority in the country of

use may be sprayed. At the time of manufacture, no harmful eects on the materials used are known to be caused

by these approved substances or natural oils dissolved in water. The fertilizers, pesticides and weedkillers are only

allowed to be sprayed in the concentrations specied by the manufacturer of the spray solutions. If in doubt, please

contact the relevant manufacturer.

The pressure sprayer is not designed to be used with foodstus or to spray liquids that exceed the maximum per-

mitted operating temperature of 40 °C. Similarly, it is prohibited to spray acidic, caustic and ammable liquids whose

ash point is below 55 °C, as well as impregnating agents, disinfectant, paints, varnishes, grease, glazes and syn-

thetically manufactured oils.

Important! Atomized ammable liquids with a ash point in excess of 55 °C are also highly combustible.

Never use the pressure sprayer

● as a ame gun.

● for storing liquids.

● for substances with unknown risk.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The

user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of

this.

10 English

ASSEMBLY

CAUTION:

Always be sure that the machine is switched o and the battery cartridge is removed before carrying out any work on

the machine.

CAUTION:

Make sure that the all parts are securely assembled so that the liquid does not leak when operating the machine.

Assembly of the spray wand

Note: The items such as nozzles and cup are included in the tank.

1. Remove the cap from the handle.

2. Make sure the O-ring is in place, then thread the spray wand onto the handle and tighten it securely. Refer to

Figure 1.

1 Vertical type 2-head Nozzle 2 Spray wand 3 O-ring

4 Handle 5 Cap 6 Weedkiller nozzle

Figure 1

Carrying strap

Attach the carrying strap to the hangers of the machine and fastening hooks for the belt in position.

Slip the belt over your shoulders and adjust the length of the belt. After that, fasten the belt so that you can work

without fatigue.

To adjust belt length, pull on the two ends of the belt to shorten it or on the two belt release mechanisms to extend it.

Refer to Figure 2.

1 Hanger 2 Fastening hooks

Figure 2

11 English

FUNCTIONAL DESCRIPTION

CAUTION:

Always be sure that the machine is switched o and the battery cartridge is removed before adjusting or checking

function on the machine.

Installing or removing the battery cartridge

CAUTION:

• Always switch o the machine before installing or removing of the battery cartridge.

• Hold the machine and the battery cartridge rmly when installing or removing battery cartridge. Failure to hold

the machine and the battery cartridge rmly may cause them to slip o your hands and result in damage to the

machine and battery cartridge and a personal injury.

• Do not use force when installing the battery cartridge. If the cartridge does not slide in easily, it is not being inserted

correctly.

• Always install the battery cartridge fully until the red indicator cannot be seen. If not it may accidentally fall out of

the tool causing injury to you or someone around you.

• Be careful not to pinch your ngers when opening or closing the battery cover.

To install the battery cartridge, pull down the locking lever, and then open the battery cover. Align the tongue on the

battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place

with a little click. Refer to Figure 3.

To remove the battery cartridge, slide it from the machine while pressing the button. Refer to Figure 4.

Figure 3 Figure 4

12 English

Indicating the residual battery capacity

Press the check button on the machine to indicate residual battery capacity. The indicator lamps light up for few

seconds. Refer to Figure 5.

Indicator lamps

Residual battery capacity

Lighted O

50 % to 100 %

30 % to 50 %

0 % to 30 %

NOTE:

• Depending on the conditions of use and the ambient temperature, the indication may dier slightly from the actual

capacity.

1Check button 2Indicator lamps

Figure 5

Machine / battery protection system

The machine is equipped with the protection system. This system automatically cuts o power to the motor to

extend machine and battery life. The machine will automatically stop during operation if the machine or battery is

placed under one of the following conditions.

- Overload protection : When the machine is operated in a manner that causes it to draw an abnormally high current,

the machine automatically stops without any indication. In this situation, turn the machine o and stop the applica-

tion that caused the machine to become overloaded. Then turn the machine on to restart.

- Overdischarge protection : When the battery capacity becomes low, the machine stops automatically. If the

machine does not operate even when the switches are operated, remove the battery cartridge from the machine

and charge it.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

1Indicator lamps 2Check button

Figure 6

13 English

Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light

up for a few seconds.

Indicator lamps

Remaining capacity

Lighted O Blinking

75 % to 100 %

50 % to 75 %

25 % to 50 %

0 % to 25 %

Charge the battery.

The battery may have malfunctioned.

NOTE: Depending on the conditions of use and the ambient temperature, the indication may dier slightly from the

actual capacity.

NOTE: The rst (far left) indicator lamp will blink when the battery protection system works.

14 English

Mixture

WARNING! Always follow the chemical manufacturer’s instructions printed on their product labeling

for use, cleaning, and storage. Clean thoroughly after each use, following the instructions in the

Maintenance and cleaning section of this manual. Chemicals should be stored out of the reach of

children. Failure to do so may result in serious personal injury.

WARNING! THE PRODUCT IS DESIGNED FOR SPRAYING CONSUMER-GRADE HOME AND

GARDEN CHEMICALS SUCH AS WEED KILLERS, FUNGICIDES, INSECTICIDES, AND FERTILIZERS.

CAUTION: Be sure that no previously used chemical has been left in tank. If so, chemical reaction may

occur generating harmful gas.

NOTICE: Do not over ll the tank. Doing so may damage the machine.

NOTICE: Liquids to be sprayed must be as thin as water. Thicker liquids will not spray properly.

15 English

1. Remove the battery prior to adding chemical liquid to the tank.

2. Remove the tank lid. Refer to Figure 7.

3. Measure the recommended liquid. The cup can be used to measure up to 200 ml ( 8 oz). Refer to Figure 8.

4. Carefully pour the liquid into the tank with measuring cup through the lling opening of the tank. You can also

dissolve chemical liquid in water completely in a separate container and then pour it into the tank.

Make sure that the tank lling strainer is in place. Refer to Figure 9.

5. Tighten the tank lid. Refer to Figure 10.

6. Rinse the measuring cup with clean water.

*Container is not included.

Figure 7 Figure 8

Figure 9 Figure 10

16 English

OPERATION

CAUTION:

When operating the machine, be sure to put on the carrying strap rmly.

Turning the machine on/o

1. Before operating the machine, put on safety goggles and other safety gear.

2. Press the On/o switch to start the machine.

3. Press and hold the lever down to start spraying. Refer to Figure 11.

4. Release the lever to stop spraying.

5. Press the On/o switch to turn o the machine.

Lock-on

The lock-on feature is convenient for continuous spray or when covering a large area.

1. To lock-on, press the lever down and pull the lock button backwards, then release the lever. Refer to Figure 12.

2. To release the lock-on, press the lever and push the lock button forward.

Note: Make sure the lever is not in locked position before inserting the battery pack into the machine.

1

2

1Lock button 2 Lever

Figure 11 Figure 12

Attaching a nozzle

Two nozzles are provided with the cordless garden sprayer. Thread the nozzle onto the end of the spray wand.

Please use only original replacement nozzle.

1Vertical type 2-head nozzle 2 Weedkiller nozzle

Figure 13

WARNING! Risk of re or explosion. Spray area must be well-ventilated and away from sparks or ames.

WARNING! The liquid outlet nut must be tightened securely throughout the operation.

WARNING! Make sure that the carrying strap is not loose or detached before operation.

17 English

Spraying

WARNING! Never set the unit on the ground during use. Avoid the machine and battery from getting wet

at all times. Do not spray near or directly at the unit.

1. Aim the sprayer nozzle directly at the plants or objects you wish to spray.

2. Never point the spray end of the wand at yourself or others.

3.

Be aware of splash back, stand far enough from the object being sprayed to prevent the spray splashing back onto you

.

4. Never spray in the direction of people or animals; always spray downwind.

5. Avoid spraying on windy days. Spray can be accidentally blown onto plants or objects that should not be sprayed.

6. Be aware of the volume application rate and check the the volume in the tank from time to time.

MAINTENANCE AND CLEANING

CAUTION:

Always be sure that the machine is switched o and the battery cartridge is removed before attempting to perform

inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed

by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

MAINTENANCE

WARNING! To avoid serious personal injury, always remove the battery pack from the machine when

cleaning or performing any maintenance.

WARNING! Always wear eye protection with side shields or goggles marked to comply with ANSI Z87.1.

Failure to do so could result in uids entering your eyes resulting in possible serious injury.

WARNING! When servicing, use only identical replacement parts. Use of any other parts may create a

hazard or cause product damage.

WARNING! Do not at any time let brake uids, gasoline, penetrating oils, etc., come in contact with

plastic parts. Chemicals can damage, weaken, or destroy plastic which may result in serious personal

injury.

NOTICE: Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all

missing or damaged parts are replaced. Please contact customer service or a qualied service center for

assistance.

NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks

may result.

GENERAL MAINTENANCE: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to

damage from various types of commercial solvents and may be damaged by their use. Use clean clothes to remove

dirt, dust, oil, grease, etc. Unless stipulated otherwise, we recommend that you arrange for the qualied technician to

check the equipment every 2 years.

CLEANING THE UNIT

WARNING! Always store and dispose of chemicals properly. Disposal of contaminated rinse water

should be performed according to local ordinances and by laws.

18 English

DRAINING THE TANK

If there is any liquid left in the tank after spraying, the tank should be drained before cleaning.

• Remove the battery pack.

• Drain the contents through the ll area and the liquid outlet.

NOTE: Make sure that the O-ring inside the liquid outlet cap is in place.

NOTE: Drain the liquid back into the original container. Do not store chemical liquid in the tank.

CLEANING THE TANK

• Fill the tank about one-third full with clean water. A small amount of mild household detergent may be added.

NOTE: Never use ammable chemicals or abrasive cleaning agents to clean the tank.

• Wipe the outside of the tank with a clean, dry cloth.

• Reinstall the battery pack. Spray until the tank has been emptied. Make sure to direct the spray toward an area that

will not be damaged by the spray solution.

• Rell and repeat the procedure with clean water. It may be necessary to rinse the tank more than once, then drain

again as instructed above.

• Allow all parts to completely dry before reinstalling parts and storing the unit.

CLEANING THE NOZZLE

If the nozzle becomes plugged, use the steps below to clear.

• Remove the battery pack.

• Loosen and remove the nozzle from spray wand.

•

Push a small wire through the exposed holes to clear any debris. Then ush with clean water. Refer to Figure 14

.

Figure 14

CLEANING THE PUMP

If the sprayer cannot draw the uid from tank or it cannot spray out liquid at the rst use or after long-term storage.

Follow the procedures below to clean the pump:

1. Switch o the machine and remove the battery.

2. Remove the spray wand from handle.

3. Drain any remaining liquid or store leftover liquid to another container to make sure the tank is empty.

4. Unscrew the red cap to open water inlet hole, and then connect the hole to the water tap. Make sure the O-ring is

placed inside the red cap. Refer to Figure 15.

5. Open the water tap slowly and press down the lever at the same time to allow water ush away any debris

adhered to the pump. Refer to Figure 16.

6. Disconnect the water tap and re-tighten the red cap. Make sure that the O-ring inside the cap is in place.

1 Red cap 2 O-ring

Figure 15 Figure 16

19 English

OPTIONAL ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makita product specied in this manual. The

use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attach-

ment for its stated purpose.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

• Makita genuine battery and charger.

NOTE:

• Some items in the list may be included in the product package as standard accessories. They may dier from

country to country.

20

中文简体

中文简体（原本）

1立式 2- 头喷嘴 2喷杆 3水箱盖 4水箱（10 L/15 L）

5喷枪支架 6喷雾软管 7操纵杆 8手柄

9背带 10 锁定操纵杆 11 电池盖 12 靠垫

13 开关 14 指示灯 15 出液口 16 挂钩（用于固定喷杆）

17 除草剂喷嘴 - - - - - -

ページが読み込まれています...

Makita DUS108, DUS158 Cordless Garden Sprayer ユーザーマニュアル

このマニュアルも適しています

Makita DUS108, DUS158 Cordless Garden Sprayer ユーザーマニュアル

関連論文

その他のドキュメント