Sony KD-55X9000C リファレンスガイド

カテゴリー
液晶テレビ
タイプ
リファレンスガイド
KD-65X9000C / 55X9000C
Television
Reference Guide
GB
CT
2
GB
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts and Controls . . . . . . . . . . . . . . . . . . . 6
Controls and Indicators . . . . . . . . . . . . . . . . . 6
Inputs and Outputs . . . . . . . . . . . . . . . . . . . . 7
Using Remote Control . . . . . . . . . . . . . . . . 9
Remote Control Parts Description . . . . . . . . .9
Using the Touchpad Remote Control . . . . . 11
Launching the Touchpad Remote
Control Introduction/Tutorial. . . . . . . . . . . . 11
Attaching the Table-Top Stand
(Alternative) . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting the TV . . . . . . . . . . . . . . . . . . 14
Installing the TV to the Wall . . . . . . . . . . 17
Using the supplied Wall-Mount Bracket . . . 17
Using an optional Wall-Mount Bracket. . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . 27
Troubles and Solutions . . . . . . . . . . . . . . . . 27
Specifications . . . . . . . . . . . . . . . . . . . . . . 28
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and
retain it for future reference.
Note
• Before operating the TV, please read “Safety Information”
(page 2).
• Instructions about “Installing the TV to the Wall” are included
within this TV’s instructions manual.
• Images and illustrations used in Startup Guide and this manual
are for reference only and may differ from actual product
appearance.
Location of the identification label
Labels for the Model No. and Power Supply rating are located on
the rear of the TV.
WARNING
Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
Installation/Set-up
Install and use the TV set in accordance with the instructions
below in order to avoid any risk of fire, electrical shock or damage
and/or injuries.
Installation
The TV set should be installed near an easily accessible AC
power outlet (mains socket).
Place the TV set on a stable, level surface to avoid it from falling
down and cause personal injury or damage to the TV.
• Install the TV where it cannot be pulled, pushed, or knocked
over.
• Install the TV so that the TV's Table-Top Stand does not
protrudes out from the TV stand (not supplied). If the Table-Top
Stand protrudes out from the TV stand, it may cause TV set to
topple over, fall down, and cause personal injury or damage to
the TV.
• Pay attention so that a child does not approach during the
Table-Top Stand installation.
• Only qualified service personnel should carry out wall
installations.
• For safety reasons, it is strongly recommended that you use
Sony accessories, including:
Wall-Mount Bracket SU-WL500
This television is designed for use in Hong Kong and ensured
the usage in Hong Kong only.
Safety Information
3
GB
GB
Be sure to use the screws supplied with the Wall-Mount Bracket
when attaching the Wall-Mount Bracket to the TV set. The
supplied screws are designed as indicated by illustration when
measured from the attaching surface of the Wall-Mount Bracket.
The diameter and length of the screws differ depending on the
Wall-Mount Bracket model.
Use of screws other than those supplied may result in internal
damage to the TV set or cause it to fall, etc.
Refer to page 17 in case of “Using the supplied Wall-Mount
Bracket”.
Refer to page 23 in case of “Using the optional Wall-Mount
Bracket”.
Transporting
• Before transporting the TV set, disconnect all cables.
• Two or three people are needed to transport a large TV set.
• When transporting the TV set by hand, hold it as shown below.
Do not put stress on the LCD panel and the frame around the
screen.
• When transporting the TV set, do not subject it to jolts or
excessive vibration.
• When transporting the TV set for repairs or when moving, pack
it using the original carton and packing material.
Ventilation
• Never cover the ventilation holes or insert anything in the
cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony Wall-Mount
Bracket in order to provide adequate air circulation.
Installed on the wall
Installed with stand
To ensure proper ventilation and prevent the collection of dirt or
dust:
Do not lay the TV set flat, install upside down, backwards, or
sideways.
Do not place the TV set on a shelf, rug, bed or in a closet.
Do not cover the TV set with a cloth, such as curtains, or items
such as newspapers, etc.
Do not install the TV set as shown below.
Do not place anything directly below the TV.
AC power cord (mains lead)
Handle the AC power cord (mains lead) and outlet (mains socket)
as follows in order to avoid any risk of fire, electrical shock or
damage and/or injuries:
Insert the plug fully into the AC power outlet (mains socket).
Operate the TV set on a 220–240 V AC supply only.
When wiring cables, be sure to unplug the AC power cord
(mains lead) for your safety and take care not to catch your feet
on the cables.
Disconnect the AC power cord (mains lead) from the AC power
outlet (mains socket) before working on or moving the TV set.
Keep the AC power cord (mains lead) away from heat sources.
Unplug the AC power plug (mains plug) and clean it regularly. If
the plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a fire.
Note
• Do not use the supplied AC power cord (mains lead) on any
other equipment.
Do not pinch, bend, or twist the AC power cord (mains lead)
excessively. The core conductors may be exposed or broken.
Do not modify the AC power cord (mains lead).
Do not put anything heavy on the AC power cord (mains lead).
Do not pull on the AC power cord (mains lead) itself when
disconnecting the AC power cord (mains lead).
Do not connect too many appliances to the same AC power
outlet (mains socket).
Do not use a poor fitting AC power outlet (mains socket).
Prohibited Usage
Do not install/use the TV set in locations, environments or
situations such as those listed below, or the TV set may
malfunction and cause a fire, electrical shock, damage and/or
injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other
vessel, inside a vehicle, in medical institutions, unstable
locations, near water, rain, moisture or smoke.
If the TV is placed in the changing room of
a public bath or hot spring, the TV may be
damaged by airborne sulfur, etc.
For best picture quality, do not expose the screen to direct
illumination or sunlight.
Avoid moving the TV from a cold area to a warm area. Sudden
room temperature changes may cause moisture condensation.
This may cause the TV to show poor picture and/or poor colour.
Should this occur, allow moisture to evaporate completely
before powering the TV on.
30 cm
10 cm
10 cm
10 cm
Do not place anything directly below the TV.
30 cm
10 cm
10 cm
Do not place anything directly below the TV.
6 cm
Air circulation is blocked.
Wall Wall
4
GB
Environment:
Places that are hot, humid, or excessively dusty; where insects
may enter; where it might be exposed to mechanical vibration,
near flammable objects (candles, etc). The TV set shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the TV.
Do not place the TV in a humid or dusty
space, or in a room with oily smoke or
steam (near cooking tables or
humidifiers). Fire, electric shock, or
warping may result.
• Do not install the TV in places subject to extreme temperature,
such as in direct sunlight, near a radiator or a heating vent. The
TV may overheat in such conditions which can cause
deformation of the enclosure and/or TV malfunction.
Situation:
Do not use when your hands are wet, with the cabinet removed,
or with attachments not recommended by the manufacturer.
Disconnect the TV set from AC power outlet (mains socket) and
antenna (aerial) during lightning storms.
• Do not install the TV so that it sticks out
into an open space. Injury or damage
from a person or object bumping into
the TV may result.
Broken pieces:
Do not throw anything at the TV set. The screen glass may break
by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have
unplugged the AC power cord (mains lead). Otherwise electric
shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set
should be disconnected from the AC power (mains) for
environmental and safety reasons.
• As the TV set is not disconnected from the AC power (mains)
when the TV set is just turned off, pull the plug from the AC
power outlet (mains socket) to disconnect the TV set
completely.
• However, some TV sets may have features that require the TV
set to be left in standby to work correctly.
For children
• Do not allow children to climb on the TV set.
Keep small accessories out of the reach of children, so that they
are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the AC power cord (mains lead)
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it checked by
qualified service personnel.
When:
AC power cord (mains lead) is damaged.
Poor fitting of AC power outlet (mains socket).
TV set is damaged by being dropped, hit or having something
thrown at it.
Any liquid or solid object falls through openings in the cabinet.
About LCD Monitor Temperature
When the LCD Monitor is used for an extended period, the panel
surrounds become warm. You may feel hot when touching there
by the hand.
WALL-MOUNT BRACKET
Below information shows the correct handling of the Wall-Mount
Bracket. Be sure to read this information thoroughly and use the
Wall-Mount Bracket correctly.
To Customers:
Be sure to observe the following precautions for safety to prevent
a serious injury through fire, electric shock, the product toppling
over, or the product dropping.
• Be sure to subcontract the installation to licensed contractors
and keep small children away during installation.
• Be sure to subcontract moving or dismounting of the TV to
licensed contractors.
• Do not remove screws, etc., after mounting the TV.
• Do not make alterations to the parts of the Wall-Mount Bracket.
• Do not mount any equipment other than the specified product.
• Do not apply any load other than the TV on the Wall-Mount
Bracket.
• Do not lean on or hang from the TV.
• Do not handle the TV with excessive force during cleaning or
maintenance.
To Sony Dealers and Contractors:
The following instructions are for Sony dealers and contractors
only. Be sure to read safety precautions described below and pay
special attention to safety during the installation, maintenance
and checking of this product.
• When handling or mounting the TV set, hold it on the sides. Do
not lift the TV by the U-shaped Bar.
• Do not install the Wall-Mount Bracket
on wall surfaces where the corners or
the sides of the TV are protruding
away from the wall surface.
• Do not install the TV over or under an
air conditioner.
• Be sure to install the Wall-Mount Bracket
securely to the wall following the
instructions in this instruction manual. If any
of the screws are loose or fall out, the Wall-
Mount Bracket may fall and cause injury or
property damage.
• Be sure to use the screws supplied with the
Wall-Mount Bracket when attaching the
Wall-Mount Bracket to the TV set. The
supplied screws are designed as indicated
by illustration when measured from the
attaching surface of the Wall-Mount Bracket. The diameter and
length of the screws differ depending on the Wall-Mount
Bracket model. Use of screws other than those supplied may
result in internal damage to the TV set or cause it to fall, etc.
See page 17 (Using the supplied Wall-Mount Bracket).
See page 23 (Using an optional Wall-Mount Bracket).
• Be sure to assemble the bracket properly following the
instructed procedure explained in this instruction manual.
• Be sure to tighten the screws securely in the designated
position.
• Be careful not to subject the TV to shock during installation.
U-shaped Bar
U-shaped Bar
5
GB
GB
Be sure to install the TV on a wall that is both perpendicular and
flat.
• After proper installation of the TV, secure the cables properly.
• Do not allow the AC power cord
(mains lead) or the connecting
cables to be pinched as the
internal conductors may become
exposed and cause a short circuit
or an electrical break.
Viewing the TV
View the TV in moderate light, as viewing the TV in poor light or
during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
• Some people may experience discomfort (such as eye strain,
fatigue, or nausea) while watching 3D video images or playing
stereoscopic 3D games. Sony recommends that all viewers take
regular breaks while watching 3D video images or playing
stereoscopic 3D games. The length and frequency of necessary
breaks will vary from person to person. You must decide what
works best. If you experience any discomfort, you should stop
watching the 3D video images or playing stereoscopic 3D
games until the discomfort ends; consult a doctor if you believe
necessary. You should also review (i) the instruction manual of
any other device or media used with this television and (ii) our
website (http://www.sony-asia.com/support) for the latest
information. The vision of young children (especially those
under six years old) is still under development. Consult your
doctor (such as a pediatrician or eye doctor) before allowing
young children to watch 3D video images or play stereoscopic
3D games. Adults should supervise young children to ensure
they follow the recommendations listed above.
• Do not use, store, or leave the 3D Glasses or battery near a fire,
or in places with a high temperature, e.g., in direct sunlight, or
in sun-heated cars.
LCD Screen
• Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective, black
dots may appear or bright points of light (red, blue, or green)
may appear constantly on the LCD screen. This is a structural
property of the LCD screen and is not a malfunction.
Do not push or scratch the front filter, or place objects on top of
this TV set. The image may be uneven or the LCD screen may be
damaged.
• If this TV set is used in a cold place, a smear may occur in the
picture or the picture may become dark. This does not indicate a
failure. These phenomena disappear as the temperature rises.
Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
The screen and cabinet get warm when this TV set is in use. This
is not a malfunction.
The LCD screen contains a small amount of liquid crystal. Follow
your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/
cabinet of the TV set
Be sure to unplug the AC power cord (mains lead) connected to
the TV set from AC power outlet (mains socket) before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
• To remove dust from the screen surface/cabinet, wipe gently
with a soft cloth. If dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild detergent solution.
• Never spray water or detergent directly on
the TV set. It may drip to the bottom of the
screen or exterior parts and enter the TV set,
and may cause damage to the TV set.
Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol, benzene,
thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in
damage to the screen surface and cabinet material.
Do not touch the TV if your hand is covered in any chemical
substance such as hand cream or sunblock.
Periodic vacuuming of the ventilation openings is
recommended to ensure to proper ventilation.
When adjusting the angle of the TV set, move it slowly so as to
prevent the TV set from moving or slipping off from its table
stand.
Optional Equipment
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
Wireless Function of the unit
Do not operate this unit near medical equipment (pacemaker,
etc.), as malfunction of the medical equipment may result.
Although this unit transmits/receives scrambled signals, be
careful of unauthorised interception. We cannot be responsible
for any trouble as a result.
Caution about handling the remote control
Observe the correct polarity when inserting batteries.
Do not use different types of batteries together or mix old and
new batteries.
Dispose of batteries in an environmentally friendly way. Certain
regions may regulate the disposal of batteries. Please consult
your local authority.
Handle the remote control with care. Do not drop or step on it,
or spill liquid of any kind onto it.
Do not place the remote control in a location near a heat source,
a place subject to direct sunlight, or a damp room.
WALL-MOUNT BRACKET
If you use the TV installed on the Wall-Mount Bracket for a long
time, the wall behind or above the TV may become discoloured
or the wallpaper may come unglued, depending on the material
of the wall.
If the Wall-Mount Bracket is removed after installing it on the
wall, the screw holes remain.
Do not use the Wall-Mount Bracket in a place where it is
subjected to mechanical vibration.
Precautions
6
GB
Parts and Controls
Remote Control sensor* / Light sensor*
/ Illumination LED
The illumination LED lights up or blinks
according to the status of the TV.
•White
When turning on the TV/picture off
mode/software update, etc.
•Cyan
When connecting with a mobile device
wirelessly.
•Amber
Timer is set.
 (Power)
CH +/- (Channel)
 +/- (Volume)
 (Input select)
Display and select the input source.
TV
Switch to a TV channel or input from other
applications.
* Do not place anything near the sensor.
Controls and Indicators
7
GB
GB
 LAN
HDMI 3 AUDIO IN
For HDMI 3 analogue audio connection.
DIGITAL AUDIO OUT (OPTICAL)
/ VIDEO IN 1
For a composite connection*.
 VIDEO IN 2, / COMPONENT IN
For a composite connection:
Use VIDEO IN, and (L/R) of
/
COMPONENT IN*.
For a component connection:
Use Y, P
B, PR, and (L/R).
(USB 1/2), (USB 3)
•Connecting a large USB device may
interfere with other connected devices
beside it.
When connecting a large USB device,
connect to the USB 1 jack.
AUDIO OUT /
To listen to the TV's sound through the
connected equipment, press HOME. Select
[Settings] [Sound] [Headphone/Audio
out] and then select the desired item.
HDMI IN 1/3/4
If the device has a DVI jack, connect it to
HDMI IN 3 through a DVI - HDMI adaptor
interface (not supplied), and connect the
device's audio out jack to HDMI 3 AUDIO
IN.
If connecting a digital audio system that is
compatible with Audio Return Channel
(ARC) technology, use HDMI IN 4. If not, an
additional connection with DIGITAL AUDIO
OUT (OPTICAL) is necessary.
HDMI IN 2/MHL
You can connect your MHL (Mobile High-
definition Link) device using an HD quality
MHL cable.
Inputs and Outputs
8
GB
 CABLE/ANTENNA
Connect to your cable or antenna (aerial).
* When connecting mono equipment, connect to the L
(MONO) audio jack.
9
GB
GB
Using Remote Control
/ (Input select/Text hold)
In TV mode: Display and select the input
source.
In Text mode: Hold the current page.
(TV standby)
Turn on or turn off the TV (standby mode).
DIGITAL/ANALOG
Switch between digital and analogue mode.
EXIT
Return to the previous screen or exit from
the menu. When an Interactive Application
service is available, press to exit from the
service.
Number buttons
(Twin picture/PIP)*
1
*
2
Display two pictures simultaneously.
(Text)
Display text information.
Colour buttons
Execute correspondent function at that time.
(Wide mode)
Change the screen format.
TV
Switch to a TV channel or input from other
applications.
HELP
Display Help Menu.
Remote Control Parts Description
IR (infrared) Remote Control
Ȫ
ȩ
ȫ
Ȭ
ȭ
Ȯ
ȯ
Touchpad Remote Control
10
GB
ACTION MENU
Display a list of contextual functions.
You can also display it by slide down your
finger from ACTION MENU on the Touchpad
Remote Control.
/ (Info/Text reveal)
Display information.
GUIDE/ *
1
Display the digital programme guide.
BACK
Return to previous screen.
HOME
Display the TV Home Menu.
DISCOVER
Bring up the Content Bar to search for
content.
You can also launch Content Bar by slide up
your finger from DISCOVER on the
Touchpad Remote Control.
//// (Item select/Enter)
 +/– (Volume)
Adjust the volume.
(Jump)
Jump back and forth between two channels
or inputs. The TV alternates between the
current channel or input and the last
channel or input that was selected.
(Muting)
Mute the sound. Press again to restore the
sound.
PROG +/–//
In TV mode: Select the channel.
In Text mode: Select the next (
) or
previous (
) page.
AUDIO
Change the language for the programme
currently being viewed.
(Subtitle setting)
Turn subtitles on or off (when the feature is
available).
//////
Operate media contents on TV and
connected BRAVIA Sync-compatible device.
SYNC MENU
Display the BRAVIA Sync Menu.
FOOTBALL
Turn Live Football Mode on or off (when the
feature is available).
(Microphone)
Use Voice Function. (e.g., Search various
content by voice.)
Touchpad
Operate the TV with the touchpad.
(NFC)
Touch the device (e.g. some models of
Xperia) corresponding to the One-touch
mirroring function, then its screen is
displayed on the TV.
*1 The location, availability and function of remote
control button may vary depending on your country/
region/TV model.
*2 Twin Picture function will be available within 2015.
You will receive Twin Picture function automatically
as a network software upgrade. Make sure your TV is
connected to the Internet. If you do not have a
network connection, you will be able to download
the software from the Sony support website using
your PC. For details on how to upgrade, please visit
the Sony support website.
11
GB
GB
Touchpad Remote Control can only be used
after pairing with the TV.
To pair, follow the pairing screen instruction.
Pairing screen can be displayed by pressing the
button on the TV for 5 seconds, or select
[Settings] - [Touchpad Remote Control settings]
- [Pair Touchpad Remote Control].
1 Press HOME.
2 Select [Settings] - [Touchpad Remote
Control settings] - [Start Introduction/
Tutorial].
Attaching the Table-Top Stand
(Alternative)
You can change the Table-Top Stand from the
edge to the middle position by referring to the
instructions below.
Note
Two or more people are needed to carry out this
installation.
Be careful not to pinch the finger during installation.
KD-65X9000C
1
Using the Touchpad Remote Control
Launching the Touchpad Remote
Control Introduction/Tutorial
Middle position
Thick cushion
1.5 N∙m/1,5 N∙m
{15 kgf∙cm}
12
GB
2
KD-55X9000C
1 Remove the lower screws, and then one
of the Table-Top Stand.
2 Attach the stand plate (supplied with the
TV) to the detached Table-Top Stand.
3 Fix the stand plate to the Table-Top
Stand with screws (M5×10) (supplied
with the TV).
4 Attach the Table-Top Stand with stand
plate to the middle position, and fix with
screws (M6×32) (supplied with the TV).
5 Take the same procedure for the other
side of the Table-Top Stand.
6 Attach stand covers (supplied with the
TV).
Soft cloth
Stand plate
M5 × 10
1.5 N∙m/1,5 N∙m
{15 kgf∙cm}
M6 × 32
1.5 N∙m/1,5 N∙m
{15 kgf∙cm}
Stand cover
13
GB
GB
Note
Two or more people are needed to carry out this
installation.
Ensure that there are no objects in front of the TV.
To bundle the cables
KD-65X9000C
KD-55X9000C
*1 Location of cable clamper when the Table-Top Stand
is attached to middle position.
*2 Location of cable clamper when the Table-Top Stand
is attached to edge position.
Note
To detach the cable clamper from the TV, press the
top of the clamper , then pinch as illustrated.
IR Sensor
*1
*2
*1
*2
14
GB
Connecting the TV
Note
To select an input device connected to the TV, press
.
When connecting the cable to the Cable/Antenna,
input finger tighten only, over-tightening the
connection can damage the TV.
To attach the terminal cover
After connecting cables, attach the terminal
cover.
To connect with an HDMI cable
To connect with component cables
Terminal
cover (left)
Terminal
cover (right)
To HDMI OUT
< 12 mm
< 21 mm
To AUDIO
OUT
To COMPONENT
OUT (P
R/PB/Y)
15
GB
GB
To connect with AV composite cables To connect MHL device
The TV simultaneously charges the MHL-
compatible connected device while playing
photo/music/video files. You can use the TV
remote control to control the connected MHL-
compatible device.
Note
If [MHL charging during standby] is set to [On], you can continue
charging the MHL-compatible device even when the TV is in
standby mode.
Use authorized MHL 3 CABLE with MHL logo for 4K smartphone
or mobile devices.
To VIDEO
OUT
Use authorized MHL
CABLE with MHL logo
(not supplied)
MHL device
16
GB
Picture Quality
AV composite cable
Antenna (aerial) cable
Standard definition (SD) videos have picture signals with a
vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.
Component cable HDMI cable
High definition (HD) videos have picture signals
with a vertical resolution of 720 or 1,080 lines.
(For 4K vertical resolution: 2,160 lines)
17
GB
GB
Installing the TV to the Wall
Your TV can be mounted on a wall using a Wall-Mount Bracket (supplied with the TV) out of the box as
packaged.
Prepare the TV for the Wall-Mount Bracket before making cable connections.
For product protection and safety reasons, Sony strongly recommends that installation of
your TV on the wall be performed by qualified professionals. Do not attempt to install it
yourself.
Follow the instructions provided with the Wall-Mount Bracket for your model. Sufficient
expertise is required in installing this TV, especially to determine the strength of the wall for
withstanding the TV’s weight.
The length of the screw for Wall-Mount Bracket differs depending on the Wall-Mount Bracket
thickness. Please see below illustration.
Note
See page 4 (Safety Information) and page 5 (Precautions) on WALL-MOUNT BRACKET before carrying out Wall-Mount
Bracket installation.
When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes
on the rear of the TV.
1 Prepare necessary items.
Wall-Mount Bracket accessories
Using the supplied Wall-Mount Bracket
To Customers
Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony
dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable
for any damages or injury caused by mishandling or improper installation, or installing any other than the
specified product. Your Statutory Rights (if any) are not affected.
To Sony Dealers and Contractors
Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly
to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or
improper installation.
Screw (M6)
Wall-Mount Bracket
8 mm - 12 mm
A Paper Template H Wall-Mount Bracket J U-shaped Bar
K Cushion
Lock plate (H1)
Lock pin (H2)
Wall-Mount Bracket (H3)
18
GB
Screws for Wall-Mount Bracket (8 mm in diameter, not supplied) (4)
2 Remove the screws from the rear of the TV before attaching the U-shaped Bar.
3 Attach the U-shaped Bar J (supplied with the TV) to the rear of the TV.
4 Attach the cushions K to the rear of the TV.
M6 × 16
M6 × 16 (previously removed)
U-shaped Bar J
1.5 N∙m/1,5 N∙m
{15 kgf∙cm}
Cushions K
19
GB
GB
5 Make sure that the wall has enough space for the TV and is capable of supporting a
weight of at least four times that of the TV.
Refer to the following table on installing the TV to the wall. See page 28-31
(Specifications) for the TV’s weight.
Unit: mm
Note
Figures in the table may differ slightly depending on the installation.
6 Pull the lock pin (H2) and detach the lock plate (H1) from Wall-Mount Bracket (H3).
Model Name
KD-
Display dimensions
Screen
center
dimension
Length for mounting
65X9000C 1,451 835 325 747 40
55X9000C 1,232 712 263 624 40
Screen center point
Wall-Mount
Bracket (H3)
Lock plate (H1)
Lock
pin (H2)
20
GB
7 Tape the Paper Template A to the wall and drill holes according to the numbering on the
Paper Template A using an electric drill.
8 Remove the Paper Template A off from the wall.
9 Attach the Wall-Mount Bracket (H3) (supplied with the TV) to the wall correctly using the
screws (8 mm in diameter, not supplied).
10 Remove the terminal covers and detach the Table-Top Stand from the TV while holding
the bottom of the TV.
Wall
A
Wall
Wall-Mount Bracket (H3)
1 / 1

Sony KD-55X9000C リファレンスガイド

カテゴリー
液晶テレビ
タイプ
リファレンスガイド

他の言語で