Product Overview
Features
4K UHD NVR Series
66-6832CSB-1
Installation Guide
Internal Hard Drives Model Front View
1 2
3 4 6
=Standalone Embedded Linux System
=Supports 4K ( UHD ) IP Cameras
=4K HDMI Output
=Compatible with iOS and Android devices
=Metadata can be embedded into videos
=Supports Setup Wizard
=HTML5 streaming, multiple browser supported
=P2P easy remote access supported
HDD LED, green, blinking, HDD activity indicator
ALARM LED, red, blinking, alarm status indicator
LAN LED, green, blinking, network activity indicator
Power LED, amber, lit constantly, power status indicator
OLED display, system activity information
USB port
1
2
3
4
5
1
2
3
4
5
7
8
9
Power socket
RJ-45 100Mbps connector x 16
RJ-45 Gigabit connector x 2
VGA output
Audio out
Line in
Reset Button
HDMI output
USB 3.0 / 2.0 port
DI/DO, RS-485, KB
6
10
Installation Instructions
Profession 2U 19" Internal Hard Drives Model
Hard drives installation
All information, trademarks, logos, graphics, and other items appearing on this manual ('Information') are for reference only and is subject to change at any time without prior notice. Whilst us endeavors
to ensure the accuracy of the Information on this manual, no express or implied warranty is given by us to the accuracy of the Information. we shall bear no responsibility for any incorrectness or leakage.
For details about NVR operation, please scan the QR code inside
the package to get the operation manual.
Begin using the NVR
Do not drop or strike the equipment.
Do not install the equipment near naked flames or heat sources.
Do not expose this unit to rain, moisture, smoke or dusty
environments.
Do not cover the opening of the unit with cloth or plastic or install
this unit in a poorly-ventilated place. Allow 10 cm between this
unit and its surroundings.
Do not continue to operate the unit under abnormal conditions
such as detection of smoke, strange smell, or malfunctioned
screen whilst power is turned on.
Do not touch the power connection with wet hands.
Do not damage the power cord or leave it under pressure.
To avoid unnecessary magnetic interference, do not operate this
unit near magnets, speaker system, etc.
All connection cables must be grounded properly.
=
=
=
=
=
=
=
=
=
Caution
RISK OF EXPLOSION IF BATTERY IS REPLATCED WITH AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
CAUTION
: Power cord to NVR power socket.
: USB mouse to NVR USB port.
: NVR video output (HDMI / VGA) to monitor input.
: NVR / IP camera ethernet connector to network switch.
: NVR PoE port to IP camera PoE port.
1. Plug USB mouse into NVR USB port.
2. Plug power cord into NVR power socket.
3. Connect network switch, plug a network cable on NVR RJ-45
Gigabit connector, opposite end of cable into network switch.
4. PoE Series NVR use with PoE IP camera, plug a network cable
on NVR RJ-45 PoE 100Mbps connector, opposite end of cable
into IP camera
5. NVR use with DC power supply IP camera, plug a network cable
on IP camera, opposite end of cable into network switch.
6. Plug HDMI or VGA cable on NVR, opposite end of cable into
monitor HDMI or VGA input.
7. Make sure all cables properly connected, power on the NVR.
Please refer to below structure diagram for installation.
Network Video Recorder Instructions
5
6
Profession 2U 19" 32ch/16port PoE Model Rear View
[32 Channel]
1 2 3
10
54
Remove NVR upper casing and loosen the screws at both sides of
the hard drive bracket to take it out, install hard drives and tighten
the hard drive with screws as instructed in the image above, and
properly connect the SATA and power cables to the connectors,
finally, complete the hard drive installationby closing NVR upper
casing and tightening the screws.
6
987
4K超高清網路錄放影機
警語: 此圖示，指在廢棄產品時不可直接丟棄垃
圾桶，應進行拆解，並分類進行回收再利用。
產品特色
安裝說明
部件說明及尺寸
= Linux
= 支援 4K 超高清網路攝影機
= 4K HDMI 輸出
= 支援 iOS 以及 Android（安卓）系統裝置
= 外部描述資料（METADATA）的記錄及影像結合
= 設定精靈，快速完成攝影機及系統設定
= HTML5 串流支援，無需安裝任何元件，
多種瀏覽器直接檢視
= P2P 簡易遠端瀏覽
嵌入式 系統 內接式硬碟機種前面板說明
硬碟指示LED，綠色、閃爍，顯示硬碟存取
警報指示LED，紅色、閃爍，顯示警報是否觸發
網路指示LED，綠色、閃爍，顯示網路是否連接
電源指示LED，橘色、長亮，顯示電源狀態
OLED 顯示器，各種系統資訊顯示
USB 埠
1
2
3
4
5
專業型2U 19英吋 32ch/16port PoE機種後背板說明
[32 頻道]
硬碟安裝說明
安裝說明
專業型 2U 19 英吋內接式硬碟機種
卸除螺絲並移除主機機殼上蓋，卸除兩側鎖點螺絲取下
硬碟安裝支架，使用配件包中螺絲將硬碟固定於硬碟支
架上，將硬碟支架置回，鎖緊硬碟支架兩側鎖點固定硬
碟支架，將硬碟接上 SATA 線及電源線。
關於錄放影機的使用請掃描包裝中所附 QR 圖碼( QR
Code )，取得完整的說明。
請勿摔落或敲打設備
= 請勿將設備安裝於火源或熱源附近
= 請勿將設備暴露於雨水、高濕度、煙霧、及高落塵的環
境中
= 請勿將設備換氣孔以衣物或任何物品遮蔽，或將設備安
裝於通風不良的環境中，請在設備周圍保留 10 公分的
間隙
= 請立即關閉設備電源當發現有煙霧、異味、螢幕無訊號
及其他異常狀況
= 操作時請保持乾燥
= 請勿凹折或重壓電源線
= 請勿將設備置遠離高磁性物體，避免不必要的干擾，如
磁鐵、或高功率喇叭等等
= 請將所有連接線材妥善接地
=
注意事項
若使用錯誤的電池會有爆炸的危險，請依照指示處理廢棄的電池
注 意
1. 將 USB 滑鼠插入網路錄影機的 USB 滑鼠連接埠
2. 將電源線接入網路錄影機的電源接頭
3. 使用 RJ-45 網路線，將一端接在網路錄影機的乙太網路
接口，另一端接入安裝環境中的網路交換器
4. 如使用 PoE 網路錄影機系列搭配 PoE 網路攝影機，使用
RJ-45 網路線，將一端接在網路錄影機的 PoE 乙太網路
接口，另一端接在網路攝影機的 PoE 乙太網路接口
5. 如使用直流供電攝影機，使用 RJ-45 網路線，將一端接
在網路攝影機的乙太網路接口，另一端接入安裝環境中
的網路交換機
6. 使用 HDMI 或 VGA 連接線，將一端接入網路錄影機的
HDMI 或 VGA 輸出埠，另一端接入螢幕的輸入埠
7. 確認上述項目都已妥善連接後開啟網路錄影機電源
參考下列架構連接錄放影機
網路錄放影機連接說明
本手冊中出現的所有信息，商標，徽標，圖形和其他項目（“信息”）僅供參考，如有更改，恕不另行通知。 儘管我們盡力確保本手冊中信息的準確性，但我們對信息的
準確性不作任何明示或暗示的保證。 對於任何錯誤或洩漏，我們概不負責。
1 2
3 4 6
5
6
電源接頭
RJ-45 百兆乙太網路接口 x 16
RJ-45 千兆乙太網路接口 x 2
VGA 輸出
聲音輸出
聲音 Line In
恢復出廠預設值
HDMI 輸出
USB 3.0/2.0 埠
DI/DO, RS-485 鍵盤輸入
1
2
3
4
5
7
8
9
6
10
：電源線 至 NVR 電源接頭
：USB 滑鼠 至 NVR USB 滑鼠連接埠
：NVR 影像輸出( HDMI / VGA ) 至 螢幕輸入
：NVR / 網路攝影機乙太網路接口 至 網路交換機
：NVR PoE 輸出至網路攝影機 PoE 輸入
開始使用4K超高清網路錄放影機
1 2 3
10
54 6
987
-
1
-
2
