銳銨科技
V0.1 (SEP. 2023)
RAIDON銳銨科技股份有限公司
銳銨科技股份有限公司
www.RAIDON.com.tw
[email protected]
銳銨科技股份有限公司
A
B
B
C
F
Hardware or GUI
Mode selection switch
D
E
Lock Unlock Press
Lock Unlock
D
A
F
I
C
EG
B
H
3.5”HDD
HDD2 HDD1
JJumper
setting for
RAID
Mode
J
Jumper
setting for
RAID
Mode
Hardware or GUI
Mode selection switch
JBOD(PM) RAID 1 RAID 0 SPAN(BIG)
Hardware 模式 GUI 模式
HDD 1HDD 2
HDD 1
HDD 2
MUTE
FAIL
MUTE
FAIL
硬碟閒置
無硬碟/硬碟故障
資料存取
資料重建(來源)
資料重建(目標)
恆亮
─ ─
恆亮
恆亮
恆亮
藍色LED
─ ─
恆亮
閃爍
─ ─
閃爍
─ ─
鳴叫
─ ─
─ ─
─ ─
紅色LED 蜂鳴器
狀態
溫度過高 ─ ─ ─ ─ 鳴叫
Package Contents and Product Views
1. Computers or servers with SATA I & SATA II & SATA III.
2. Hard drive with SATA I & SATA II & SATA III.
3. The product allows the user to simultaneously utilize two hard drives manu factured by different
companies.
4. Please make sure that the two hard drives are free from bad blocks or defects prior to installation
in order to avoid system crashes or data loss.
5. The actual storage capacity of IR2302 recognized by the system may differ from the total capacity
stated on the hard drives combined once the drives have been formatted.
6. It is highly recommended for users to back up important data contained within the IR2302 on a
regular basis or whenever the user feels necessary to a remote or a separate storage device.
Stardom will not be responsible for any lost of data caused during the use of the unit or the recovery
of the data lost.
Hardware Requirements and Precautions
Hardware Installation
Please check the product and accessories for any defect or missing parts. If you have
any questions, please contact your product supplier.
Please visit the official website (www.raidon.com.tw) to download user manuals, drivers
and other related resources.
Raidon
RAIDON is one brand under RAIDON TECHNOLOGY, INC.
Thank you for choosing RAIDON’s product.
The information provided in this manual was checked before publication, but the actual product
specications may have changed before shipping; Latest product specications and updates
can be found at www.RAIDON.com.tw or through your sales representative. No separate
notications will be provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product
information, instruction manuals, or rmware, please contact Suppor[email protected] for
assistance.
All product-related content in this manual are copyrighted by RAIDON TECHNOLOGY, INC.
Please follow the instructions below to complete the hardware installation.
1.
Lock Unlock Press
For the 3.5" HDD tray, please use
the key included in the accessory
kit to unlock the HDD tray key lock,
and then press the HDD tray key
lock. The removable drive tray will
pop open and extract the
removable drive tray.
2. For 3.5" HDD/SSD, please secure
it by use six the larger screws
included in the accessory kit. For
2.5" HDD/SSD, please secure it
by use four the smaller screws
included in the accessory kit.
For the 2.5" HDD tray, please use
the key included in the accessory
kit to unlock the 2.5" HDD tray key
lock and push the HDD eject
button to the right, the 2.5" HDD
tray handle will pop up to remove
the tray.
Properly connect SATA cable and power cable from your system to the device.
Power on your system after hardware installation is completed, and your operating
system will automatically detect the hard drives from booting. Then follow the steps
from your operating system to partition and format the drives when necessary,
device will be ready to use once the format is completed.
6.
V0.1 (SEP. 2023)
Front view Rear view
2.5” HDD/SSD status indicator LED
A
3.5” Tray Key Lock
3.5” HDD/SSD status indicator LED
B
2.5” Tray Key Lock
C
D
E3.5” HDD Tray
2.5” HDD Tray
F
Hardware or GUI
Mode selection switch
7+15Pin SATA Connector(
3.5”HDD
)
G
7+15Pin SATA Connector(HDD1&HDD2)
H
I
Lock Unlock
LED Instruction
3.
5.
When the HDD/SSD installation has been completed, insert the hard drive tray into the system
horizontally and secure the latch into place.
4.
Open the package and you should find the following:
IR2302
Device
x1
Contents of Product Package
Note1: While using a different SSD Hard Drives, the LED Indication might be with a different light set.
Note2: If the SSD is supported, the LED has a flashing function during data access; if there is no
support, there is no flashing function.
Cooling Fan
Mute Switch
Buzzer
Jumper
setting for
RAID
Mode
Fan Fail LED
HDD Idle
HDD Fail or Adsent
HDD Access
Rebuilding(Source)
Rebuilding(Target)
Light On
─ ─
Light On
Light On
Blue LED
─ ─
Light On
Blinking
─ ─
Blinking
─ ─
On
─ ─
─ ─
─ ─
Red LED Buzzer
Status
Temp Fail ─ ─ ─ ─ On
Light On
Jumper
setting for
RAID
Mode
Hardware or GUI
Mode selection switch
JBOD(PM) RAID 1 RAID 0 SPAN(BIG)
Hardware 模式 GUI 模式
HDD 2
HDD 1
MUTE
FAIL
D
A
F
I
C
EG
B
H
3.5”HDD
HDD2 HDD1
J
HDD 1HDD 2
MUTE
FAIL
-
1
-
2
