Acrel ATE Series ユーザーマニュアル

タイプ
ユーザーマニュアル
安科瑞电气股份有限公司
322
ATE 系列无线测温传感器
ATE series Wireless Temperature Sensor
安装说明 V1.9
Installation Instruction V1.9
安科瑞电气股份有限公司
Acrel Co., Ltd.
安科瑞电气股份有限公司
目录
1安装指南 ...................................................................................................................................................... 1
1 Installation Guide .......................................................................................................................................... 1
1.1 产品概述 ........................................................................................................................................... 1
1.1 Product Introduction...........................................................................................................................1
1.2 型号说明 ........................................................................................................................................... 1
1.2 Type Introduction............................................................................................................................... 1
1.3 技术指标 ........................................................................................................................................... 2
1.3 Technical Features ..............................................................................................................................2
1.4 产品安装 ........................................................................................................................................... 3
1.4 Product Installation.............................................................................................................................3
附录 ................................................................................................................................................................ 12
Appendix .........................................................................................................................................................12
注意事项 ................................................................................................................................................ 12
Precautions ..............................................................................................................................................12
安科瑞电气股份有限公司
1
1安装指南
1 Installation Guide
1.1 产品概述
1.1 Product Introduction
ATE 线据 《NB/T 42086-2016 线》 开
3~35kV 户内开关柜,置柜、手车柜、固定、环柜等种开柜;也可用0.4kV
柜,包括固定柜,抽屉柜等。无线测温传感器可安装于柜内任何发热点上,利用无线数据传输技术
实时发送监测数据,再通过接收装置将温度数据传输到显示装置或者远程监控系统
ATE series wireless temperature measuring sensor has been developed in compliance with
Specification for Wireless Temperature Measuring equipment, NB/T 42086-2016. It is suitable for 3-35kV
indoor switchgears, including built-in switchgears, handcart switchgears, fixed switchgears and loop-net
switchgears. It is also suitable for 0.4kV low-voltage switchgears such as fixed switchgears and drawer
switchgears. The wireless temperature sensors can be installed at any heating point in switchgears, the
device utilizes the wireless data transmission technology for real-time transmission of monitored
temperature data. In addition, it can be transmitted to display device or remote intelligent monitoring
system.
1.2 型号说明
1.2 Type Introduction
ATE
表示无线测温传感器
Wireless temperature measuring sensor
XXX
型号:
Type:
100 表示螺栓式,100M 表示磁吸式,200
表示表带式,400 表示合金片固定,100P
表示户外螺栓式,200P 表示户外表带式
100 is bolted, 100M is magnetic,200 is belt,
400 is tied with cable tie, 100P is outdoor
bolted, 200P is outdoor belt
安科瑞电气股份有限公司
2
1.3 技术指标
1.3 Technical Features
项目
Items
指标
Features
环境要求
Environment
工作温度
Temperature -40~125
相对湿度
Humidity 95%
大气压力
atmospheric pressure 86kPa~106kPa
ATE100M/100/200
有源无线温度传感
ATE100M/100/200
Active wireless
temperature sensor
无线频率
Wireless frequency 470MHz
通讯距离
Communication distance
空旷 150m
150m in open area
采样频率
Sampling frequency 25s
发射频率
Transmitting frequency 25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
磁吸式/螺栓式/表带式
Magnetic / bolted /Belt
测温范围
Range of temperature -50~+125
精度
Precision ±1
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
电池寿命
Battery life
5年(25℃)
5 years25℃)
ATE400 无源无线
温度传感器
ATE400 Passive
wireless
temperature sensor
无线频率
Wireless frequency 470MHz
通讯距离
Communication distance
空旷 150m
150m in open area
采样频率
Sampling frequency 15s
发射频率
Transmission frequency 15s
工作电源
Power source
CT 感应取电,启动电流5A
CT-powered, starting current≥5A
安装方式 合金片固
安科瑞电气股份有限公司
3
1.4 产品安装
1.4 Product Installation
无线温度传感器共有多种型号,分别对应磁吸固定、螺栓固定、表带固定、合金片固定等安装
方式。
There are several types of wireless temperature sensors and mounting methods correspondingly, i.e.
Magnetic , bolted , belt and alloy chip fixing.
Installation alloy chip fixing
传感器探头
Sensor probe
合金底座
alloy bottom
测温范围
Range of temperature -50~125
精度
Precision ±1
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
ATE100P/200P
外无线温度传感
ATE100P/200P
Outdoor wireless
temperature sensor
无线频率
Wireless frequency 470MHz
通讯距离
Communication distance
空旷 150m
150m in open area
采样频率
Sampling frequency 25s
发射频率
Transmitting frequency 25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
螺栓式/表带
bolted /Belt
测温范围
Range of temperature -50~+150
精度
Precision ±0.5
应用范围
Application
电气接头
Voltage switchgears
电池寿命
Battery life
5年(25℃)
5 years25℃)
防护等级
Protection level IP68
安科瑞电气股份有限公司
4
1.4.1 外形尺寸
1.4.1 Shape Size
ATE100M
ATE100/ATE100P
ATE200/ATE200P
安科瑞电气股份有限公司
5
ATE400
1.4.2 标签说明
1.4.2 Label Instructions
1.4.2.1 ATE 传感器搭配 ASD/ARTM-Pn 装置
1.4.2.1 ATE sensor with ASD/ARTM-Pn device
ASD320 ARTM-Pn
ATE400
ATE100ATE100M ATE200
ATE200PATE100P
如果ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P,其组号装置标签
安科瑞电气股份有限公司
6
形码最后四位编号一致,即“1”对应*51809190240001*”,安装位置依照标签文字安装,
编码:1A”为安装第一个 A相,“编码:1B”为安装第一个 B相,以此类推。
If the sensor is ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P, the number behind “组号:
should be same as number underlined in “*51809190240001*”, the sequence of installation is base on the
label, “编码:1A” is first one on the phase A, “编码:1B” is first one on the phase Band so on.
注意:出厂时包装箱内无线温度传感器与显示装置已配对,不可以与其他显示装置或无线温度
传感器混用,无线温度传感器按照标签安装。
Notice: wireless temperature sensors and display device in the package have been matched
before delivery. Do not use them with other display device or other wireless temperature sensors
together. Please installing them with label on the sensor.
1.4.2.2 ATE 传感器搭配 ATC600/ATC450-C 收发器
1.4.2.2 ATE sensor with ATC600/ATC450-C coordinator
ATC450-C
ATC600
ATE400
ATE100ATE100M ATE200
ATE200PATE100P
如图所示,如果安装 ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P ,其组号应与
ATC450-C/ATC600 的组号一致,安装位置依照标签文字安装,“编码001”建议安装在第一个柜
子的第一个测温点,再依次按照测温点顺序安装。
According to the above pictures, If the sensor is ATE100M/100/200/400/100P/200P, the group
number of ATE must be same with the group number of ATC450-C/ATC600 and the installation order is
base on the label. The code of each sensor is used to distingguish each sensor from same group. code:
001is recommended to be installed on the first temperature measuring point of the first cabinet, and then
installed other sensors in this order.
若有特殊情况,请联系相关工程师进行沟通解决。
In case of any special situation, please contact the relevant engineers for communication.
安科瑞电气股份有限公司
7
1.4.3 安装方法
1.4.3 Installation Method
1.4.3.1 ATE100M 安装方法
1.4.3.1 ATE100M Installation Method
ATE100M 磁吸式无线测温传感器适用于铁质的电气节点或设备表面。
The magnetic wireless sensor ATE100M is suitable for iron electrical nodes or equipment surfaces.
磁吸式无线温度传感器 ATE100M 结构说明:
Structure introduction of ATE100M:
1 —— 无线温度传感器主The core of wireless temperature sensor ATE100M
2—— 测温部位 Thermo-sensitive part
3 —— 电池开关 battery switch
2
1
1
3
1
直接吸附在铁质测温点处,安装前打开电池开关,电源指示灯闪烁两次。安装实例见下图:
Adsorbed directly at the iron temperature measuring point, open the battery switch before installation,
the power indicator flashes twice. The installation examples see images below.
1.4.3.2 ATE100 安装方法
1.4.3.2 ATE100 Installation Method
ATE100 螺栓式无线测温传感器适用于电缆与母排搭接处,电缆与隔离刀闸搭接处
The bolted type wireless sensor ATE100 is suitable for use at joints between cable and bus bar and
joints between cable and disconnector.
ATE100 螺栓式无线温度传感器结构说明
ATE100 structure introduction:
1 —— 无线温度传感器主The core of wireless temperature sensor ATE100
2 —— 测温部位 Thermo-sensitive part
3 —— 电池开关 battery switch
安科瑞电气股份有限公司
8
3
1
2
1
拆下安装位置搭接处的螺丝,将传感器固定在安装位置,对准合金底板的开孔,然后旋紧螺丝
固定,安装前打开电池开关,电源指示灯闪烁两次。安装实例见下图
Remove the screw from the joints, and fixing the sensor on the position with the hole on the alloy
baseplate, then tighten the screw, open the battery switch before installation, the power indicator flashes
twice. The installation examples see images below.
1.4.3.3 ATE200 安装方法
1.4.3.3 ATE200 Installation Method
ATE200 表带式无线测温传感器适用于断路器静触头、电缆接头、母排等处。
The strap-secured type called ATE200 is suitable for use at moving contacts and fixed contacts of
breaker, cable joints and bus bar.
表带式无线温度传感器结构说明:
ATE200 structure introduction:
1 —— 线The core of wireless temperature sensor ATE200,
temperature measuring probe is on the other side
2 —— 表带及锁扣 strap and hasp
3 —— 电池开关 battery switch
安科瑞电气股份有限公司
9
1
3
1
2
将传感器主体固定在安装位置,将表带绕过安装母排或者触头穿过表带,表带头收紧,最后
表带尾用锁扣锁紧。表带过长可以剪掉多余部分,表带过短可以联系我司增订。安装前打开电池开
关,电源指示灯闪烁两次。安装实例见下图:
注:ATE200 可安装静触头,铜排,电缆头。
Fixing the body of sensor on the position, then strapping it on the bus bar or breaker contact and
frapping it through the hole on the strap, fixing the strap by hasp. Clipping the strap if it is too long when
finished, if it is too short, contacting us for strap parts before installation. Open the battery switch before
installation, the power indicator flashes twice.The installation examples see images below.
Note: ATE200 can be installed with fixed contact, copper plate and cable head.
1.4.3.4 ATE400 安装方法
1.4.3.4 ATE400 Installation Method
ATE400 迷你型无线温度传感器适用于静触头,母排,电缆,母排、电缆搭接处等多种场合。
The mini type called ATE400 is suitable for using at moving contacts, bus bars, cables and joints
between bus bar and cable.
迷你型无源无线温度传感器结构说明:
Mini type passive temperature sensor structure introduction:
1 —— 温度传感器主The core of wireless temperature sensor ATE400
2 —— 合金底座,与温度探头接触 alloy bottom, touched with temperature probe
3 —— 锁扣,用于固定合金片 metal hasp, for fixing alloy chip
4 —— 取电合金片,用于感应取电 alloy chip, for CT-powered
5 —— 硅胶垫片,用于支撑合金silicone gasket, used to support the alloy chip
6 —— 合金片安装孔,用于安装合金片 alloy chip hole, used to install the alloy chip
安科瑞电气股份有限公司
10
2
1
6
5
1
3
1
4
1
1
2根合金片穿过锁紧件安装孔,将合金片居中对折后锁紧件固定在折弯处;将对折后的 4
合金片分别穿过硅胶垫片-传感器主体-硅胶垫片;将整体传感器环绕安装部位一圈后拉紧合金片并
旋紧螺丝;合金片多余部分留取适当长度并折叠压紧。合金片安装示意过程如下:
注:ATE400 可安装静触头排,电缆头;如需安装动触头,需要考虑梅花头及套筒高度是否
足够。
Firstly, take 2 pieces of alloy chips through the mounting hole of metal hasp, meanwhile fold the alloy
chips and fix the metal hasp in the middle of alloy chips. Secondly, take the folded alloy chips through one
silicone gasket, the core of ATE400 and another silicone gasket in turn.Thirdly, circle the whole alloy chips
around the mounting position and tension the alloy chips, then tighten the screw on the metal hasp. Finally,
subtract the excess alloy chips. The complete installation process is shown in Figures 1 to 4.
Note: ATE400 can be installed with fixed contact, copper plate and cable head; If it is necessary to
install moving contacts, it is necessary to consider whether the height of plum blossom head and sleeve is
sufficient.
ATE400 无线温度传感器安装实例如下:
The wireless temperature sensor called ATE400 installation examples, see images below.
安科瑞电气股份有限公司
11
1.4.4 无线温度收发器
1.4.4 Wireless Temperature Coordinator
ATE 系列无线测温传感器配套使用的无线温度收发器 ATC450-C可以采用导轨DIN35mm
安装方式,也可以使用螺栓固定方式。
The wireless temperature coordinator connected with ATE series wireless temperature sensor
ATC450-C which can be mounted on rail (DIN35mm) or bolted directly.
ATE 系列无线测温传感器配套使用的无线温度收发器 ATC600可以采用导轨(DIN35mm
安装方式。
The wireless temperature coordinator connected with ATE series wireless temperature sensor
ATC600 which can be mounted on rail (DIN35mm).
安科瑞电气股份有限公司
12
附录
Appendix
注意事项
Precautions
1)请根据安装位置以及要求选择最合适的无线测温产品。
1Please select the most suitable wireless temperature measurement product according to the
installation location and requirements.
2)所有传感安装,请格按说明书的装说明。因安装错,导致安附件
够,需由客户自行承担。
2For the installation of all sensors, please strictly follow the instructions in the manual. If there is
insufficient accessories due to installation errors, the customer shall bear the responsibility.
3)无线测温下单前,需要有详细的配置方案,并在下单时填写安科瑞无线测温确认表!将
配置方案及无线测温确认表一同交给内勤
3Before placing an order for wireless temperature measurement products, you need to have a
detailed configuration plan, and fill in the Acrel Wireless Temperature Measurement
Confirmation Form ! Then submit the plan and form to the back office.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Acrel ATE Series ユーザーマニュアル

タイプ
ユーザーマニュアル

他の言語で