dji CP.OS.00000281.01 ユーザーガイド

Osmo Action GPS

Bluetooth Remote Controller

User Guide

使用说明

2023.08v1.0

User Guide 3

使用说明 11

Contents

CHS

Disclaimer

By using this product, you signify that you have read, understand, and accept the terms and

conditions of this guideline and all instructions at https://www.dji.com/osmo-action-4. EXCEPT

AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT HTTPS://WWW.

DJI.COM/SERVICE/POLICY, THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE

THROUGH THE PRODUCT ARE PROVIDED "AS IS" AND ON "AS AVAILABLE BASIS" WITHOUT

WARRANTY OR CONDITION OF ANY KIND.

Safety Guidelines

1. Putoutanyproductreusingwater,sand,areblanket,oradrypowderreextinguisher.

2. Theproductshouldonlybeusedintemperaturesfrom-10°to45°C(14°to113°F).

3. DONOTdisassembleorpiercetheproductinanywayorthebatterymayleak,catchre,or

explode.

4. DONOTdroporstriketheproduct.DONOTplaceheavyobjectsontheproduct.

5. DONOTheattheproduct.DONOTputtheproductinamicrowaveovenorapressurized

container.

6. DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the

productinsideofavehicleonhotdays.DONOTstoretheproductinenvironmentsabove

45°C(113°F).Theidealstoragetemperatureis22°to28°C(72°to82°F).

7. DONOTstoretheproductforanextendedperiodafterfullydischargingthebattery.

Otherwise,thebatterymayover-dischargeandcauseirreparabledamage.

8. Dischargeandchargethebatterycompletelyonceeverythreemonthstokeepitingood

workingcondition.

Introduction

OSMOTMActionGPSBluetoothRemoteController(hereinafterreferredtoas“remotecontroller”)

connects to Osmo Action 4* via Bluetooth. Users can control the camera remotely to capture

footage using the remote controller. The remote controller supports single-camera and multi-

cameracontrolmodessothatuserscanshootwithupto16camerassimultaneously.Thebuilt-

insatellitepositioningmodulesenableuserstorecordaccuratedatainmotion.Whenusedwith

the DJITM Mimo app, users can add a host of collected data to enrich the video, such as speed,

route, direction, and elevation.

Withthewriststrap,theremotecontrollercanbeinstalledindifferentplacessuchasthe

handlebarofthebicycle,whichcanbeexiblyadjustedtoshootinvarioussportsscenes.

* SupportforDJIdeviceswillbeupdatedcontinuously.VisitthecorrespondingDJIOsmoActioncamera

product page for a complete list.

Overview

1. QuickSwitchButton

2. Shutter/Record Button

3. USB-C Port

4. Status LED

5. Screen

6. LinkButton

7. LanyardHole

8. Wrist Strap Hole

9. BluetoothRCWristStrap(Long)

10. BluetoothRCWristStrap(Short)

Button Features

Quick Switch Button

• Press and hold: power on or off the remote controller.

• Pressonce:switchbetweenshootingmodeswhenconnectedtothecamera.

Link Button

• Pressandhold:linktheremotecontrollerandthecamera.

• Press once: power on the camera when the camera is in sleep mode and connected to

theremotecontroller.Duringthelinkingprocess,pressoncetocancellinking.

Shutter/Record Button

• Press and hold: power off the camera. When the camera is in sleep mode, press and hold

to power on the camera.

• Pressonce:takeaphotoorstart/stoprecording.Whenthecameraisinsleepmode,press

once to start SnapShot.

Note: bothbothscenariosrefertosituationswhentheremotecontrollerisconnectedtothe

camera.

Button Combinations

• Press and hold the shutter/record button and link button for four seconds: switch

betweensingle-cameracontrolmodeandmulti-cameracontrolmodeandstartlinking.

• Press and hold the quick switch button and shutter/record button for four seconds:

view the firmware version of the remote controller

• Press and hold the quick switch button and link button for four seconds: forget the

Bluetoothconnectionandstartlinking.

QuickSwitchButton

LinkButton

Shutter/Record Button

Screen Description

Thescreendisplaysthestatusoftheconnectedcamera,thebatteryleveloftheremote

controller, and other information. When controlling multiple cameras, the screen displays the

numberofcamerasconnected.Thedisplayonthescreenvariesdependingonthecamera

mode.

1. VericationCode:displaysthevericationcode.Whenthecameraisfound,boththeremote

controllerscreenandthecamerascreenshowthesamevericationcode.TapAcceptonthe

camera screen.

2. GPS Signal: displays GPS signal strength. When the remote controller is searching for the

GPS signal, the iconwillbedisplayed.

3. BatteryLevel:displaysthebatteryleveloftheremotecontroller.

4. Connection Status: displays the connection to the camera via Bluetooth.

5. microSDCardInformation:displayseithertheremainingnumberofphotosorthevideo

durationthatcanbetakenorrecordedaccordingtothecurrentshootingmode.Theiconis

displayed only when a camera is connected.

6. ScreenInformation:thecamerainformationwillbesynchronizedwhenthecamerais

connected.

The screen will enter sleep mode if there is no operation within 3 minutes. The remote

controller will power off if there is no operation after 10 minutes when there is no camera

connectedandtheremotecontrollerisnotcharging.Whenthescreeniso,pressanybutton

toexitsleepmodeandcontinueusingtheremotecontroller.

1 2 3

Operation

Installation Methods

Thepackageincludestwowriststrapsofdierentlengths.Theremotecontrollercanbexed

tothewristusingthelongwriststrapandcanalsobexedtothebicyclehandlebar,motorcycle

handlebar,backpackstrap,andotherlocationsusingtheshortwriststrap.

Installing the Long Wrist Strap

Fixtheremotecontrollerinasuitablepositiononthewristandfastenthehook-and-loop

fastenerproperly,asshownbelow.

Installing the Short Wrist Strap

1. Removethebucklefromtheholeofthelongwriststrap,asshownbelow.

2. Threadtheshortwriststrapthroughthestrapslotonthebackoftheremotecontroller.

Makesurethatthesidewiththeraisedsurfaceisfacingupward.

3. Adjust the position of the remote controller on the wrist strap until one end of the strap slot

reachestheraisedsurface.Threadthebucklethroughtheholeontheshortwriststrap.

Linking

Linking in Single-Camera Control Mode

When powered on, the remote controller automatically searches for and connects to any Osmo

Action4cameras.Followthepromptsonthecamerascreentolinkthedevices.

Linking in Multi-Camera Control Mode

Whenpoweredon,theremotecontrollerwillbeinsingle-cameracontrolmodebydefault.

Pressandholdtheshutter/recordandlinkbuttonsforfoursecondstoswitchintomulti-camera

controlmode.Thentheremotecontrollersearchesforthecamerasandstartsthelinking

process.Followthepromptsonthecamerascreentolinkthedevices.Whencontrollingmultiple

cameras,thescreendisplaysthenumberofcamerasconnected.

Duringlinking,thestatusLEDoftheremotecontrollerwillblinkblue.Afterlinkingtheremote

controller to the camera, users can control the camera remotely to capture footage using the

remote controller.

Controlling the Cameras

Single-Camera Control Mode

Insingle-cameracontrolmode,pressthequickswitchbuttononcetoswitchbetweenshooting

modes.Theshootingmodesthatcanbeswitchedarethesameasthesettingsinthecamera.

Presstheshutter/recordbuttononcetotakeaphotoortostartorstoprecording.

Multi-Camera Control Mode

In multi-camera control mode, the remote controller can control each camera to use its set

shootingmodetocapturevideosorimages.Pressthequickswitchbuttontosetallcameras

toaunifiedshootingmode.Presstheshutter/recordbuttononcetotakeaphotoorstart

recordingandpresstwicetostoprecording.Theshootingparameterswillbebasedonthe

presets of each camera in this mode.

4. Threadthestrapthroughthebuckleandfastenthehook-and-loopfastenerproperly.

Dashboard

Thebuilt-insatellitepositioningmodulesenableuserstorecordtnessdataaccuratelywhen

shooting. When used with DJI Mimo, users can add a host of collected data to enrich the video,

such as speed, route, direction, and elevation.

• Makesuretousetheremotecontrollerinanopenoutdoorenvironmenttoavoidsignal

interferenceandwait1-2minutesuntiltheGPSsignalisstrong.Makesuretheremote

controllerfacesupwardfortheoptimalGPSsignal.DONOTblockthetopoftheremote

controllerwithyourhandsorotherobjects.

• The remote controller does not have a GPS signal underwater. DO NOT use the remote

controller underwater.

Charging the Battery

Connect the remote controller to a charger via the USB-C port.

Status LED

Status Indicator Descriptions

Charging Status When Powered O

Solidgreenfor6secondsandturnso Charging completed

Blinksgreenfourtimes Charging,76%-100%

Blinksgreenthreetimes Charging,51%-75%

Status LED

Specications

Model OSMO-AF-336

Dimensions 40.5×38.6×20.5mm

Weight 26 g

Waterproof Level IPX7

EectiveRemoteControlDistance* 25m

GNSS GPS+BeiDou+Galileo+GLONASS

Bluetooth

Protocol BLE5.0

Operating Frequency 2.4000-2.4835GHz

TransmitterPower(EIRP) <10 dBm

Battery

Capacity 270mAh

Battery Type ChargeableLithiumBattery

Charging Temperature 0°to45°C(32°to113°F)

Operating Temperature -10°to45°C(-14°to122°F)

* Theeectiveremotecontroldistanceismeasuredinaninterference-freeoutdoorenvironmentwithoutany

obstacles.

Blinksgreentwice Charging,26%-50%

Blinksgreen Charging,0%-25%

System Status

Blinksredthreetimes Poweronoro

Blinksblue Linking

Operation Status

Solid green Ready to use

Temporarilyo Takeaphoto

Blinksred Recording a video

CHS

免责声明和警告

使用本产品前，请您仔细阅读并遵守本安全概要、访问 https://www.dji.com/osmo-action-4

阅读《用户手册》和其他指引。使用本产品视为您已经阅读并接受与本产品相关的全部条款。

安全操作指引

1. 若产品起火，请根据实际情况按以下推荐顺序使用灭火器材：水、水雾、沙、灭火毯、干粉、

二氧化碳灭火器。

2. 请在温度为 -10℃至 45℃之间的环境中使用产品。

3. 禁止以任何方式拆解产品。若拆解过程中刺破电池，将会导致电池内部电解液泄漏、甚至引

发起火、爆炸。

4. 禁止机械撞击、碾压或抛掷产品。请勿在产品上放置重物。

5. 切勿对产品进行加热。请勿将产品放置于微波炉或压力锅中。

6. 禁止将产品放在靠近热源（火炉或加热器等）的地方以及将产品置于热天的汽车内。切勿将

产品存储在超过 45℃的环境下。理想的存储环境温度为 22℃-28℃。

7. 切勿将电池彻底放完电后长时间存储，以避免电池进入过放状态而造成电芯损坏，将无法恢

复使用。

8. 每隔 3个月左右重新充放电一次以保持电池活性。

CHS

简介

OSMOTM Action GPS 蓝牙遥控器（以下简称“遥控器”）使用无线蓝牙的方式与 Osmo Action 4*

连接，实现操控相机进行远程拍摄。遥控器支持单机控制和一控多机，最多可同时控制 16 台相

机进行拍摄。遥控器内置多模卫星定位模块，可精准记录运动数据，连接 DJITM Mimo App 后，

可添加实时运动数据（如速度、路线、方向及海拔等）至拍摄素材中并导出。

遥控器安装方式简单，支持通过腕带固定于手腕、自行车车把等位置，以便帮助更好完成各种

运动场景下的拍摄。

*适用的 DJI 设备会持续更新，请访问 Osmo Action 系列运动相机产品页面查看详细列表。

部件介绍

1. 快速切换按键

2. 拍摄按键

3. USB-C 接口

4. 状态指示灯

5. 显示屏

6. 对频按键

7. 挂绳孔

8. 腕带槽位

9. Osmo Action 蓝牙遥控器腕带（长）

10. Osmo Action 蓝牙遥控器腕带（短）

CHS

按键功能

快速切换按键

• 长按：开启或关闭遥控器。

• 短按：当遥控器与相机连接时，可切换相机拍摄模式。

对频按键

• 长按：遥控器与相机开始配对。

• 短按：当遥控器与相机连接时，唤醒相机。当处于配对过程时，取消对频。

拍摄按键

• 长按：使相机休眠或唤醒相机。

• 短按：拍照或开始 /停止录像。当相机处于休眠状态时，唤醒相机并进行 SnapShot 录制。

注意：在遥控器与相机保持连接的情况下，使用拍摄按键控制相机相关功能。

组合按键

• 同时长按拍摄按键与对频按键 4秒：切换一控多机或单机控制，并进入配对状态。

• 同时长按快速切换按键与拍摄按键 4秒：查看遥控器当前的固件版本信息。

• 同时长按快速切换按键与对频按键 4秒：清除当前所有相机的连接信息，并进入配对状态。

快速切换按键

对频按键

拍摄按键

CHS

显示屏说明

Osmo Action GPS 蓝牙遥控器的显示屏可显示已连接相机状态和遥控器电量等信息。一控多机

时，可显示当前连接相机数量。不同状态显示的内容不同，请以实际显示为准。

1. 相机验证码：显示遥控器与相机连接的验证码。当找到相机后，遥控器屏幕和相机屏幕会显

示验证码，在相机屏幕点击“接受”。

2. GPS 定位状态：显示当前的 GPS 信号强度。当遥控器正在搜索 GPS 信号时，将显示。

3. 遥控器电量：显示遥控器的剩余电量。

4. 连接状态：显示与相机的蓝牙连接状态。

5. 相机 microSD 卡信息：与相机连接成功后，显示相机内 microSD 卡可存储的照片数量或可

拍摄时长。

6. 界面信息：与相机连接成功后，同步相机拍摄信息。

如果 3分钟内无按键动作，显示屏将熄屏省电；未连接相机且非充电状态时，显示屏熄屏后 10

分钟内如果依旧无按键动作，蓝牙遥控器将自动关机。显示屏熄屏期间按任意按键可重新点亮

屏幕，蓝牙遥控器正常工作。

1 2 3

CHS

使用方法

固定方式

包装内含有长度不同的两根腕带。通过长腕带可以把遥控器固定至手腕处，通过短腕带可以把

遥控器固定至自行车车把、摩托车车把、背包带等位置。

安装长腕带至手腕

如下图所示，将遥控器固定至手腕合适位置后扣紧魔术贴。

安装短腕带至自行车车把

1. 如下图所示，先将口字扣从长腕带的孔位取下。

2. 将短腕带穿过遥控器背面的腕带槽位，注意将有凸起限位的一面朝上。

3. 调整遥控器在腕带上的位置，直至槽位的一端抵住凸起限位。将口字扣穿过短腕带的孔位。

4. 将腕带的另一端穿过口字扣后扣紧魔术贴。

CHS

配对

单机配对

遥控器开机后默认进入单机配对模式，将自动搜索相机并进行配对。根据相机界面提示进行配

对授权操作。

多机配对

遥控器开机后默认进入单机配对模式，同时长按拍摄按键与对频按键 4秒可进入一控多机模式。

遥控器将自动搜索相机并逐个进行配对。根据相机界面提示进行配对授权操作。一控多机时，

遥控器的显示屏将显示当前连接相机数量。

配对过程中遥控器机身持续闪烁蓝灯，直至配对成功。配对完成后，可以通过遥控器控制相机

拍照、录像等操作。

控制拍录

单机控制

单机控制模式下，短按快速切换按键可控制相机切换拍摄模式。可供切换的拍摄模式与相机内

的设置一致。短按拍摄按键可控制相机拍照或开始 /停止拍摄。

多机控制

一控多机模式下，默认情况下遥控器可以控制各相机使用各自的拍摄模式进行拍摄。短按快速

切换按键，可以将全部相机切换至统一的拍摄模式。短按拍摄按键控制相机开始拍摄，双击拍

摄按键控制相机停止拍摄。拍摄规格参数将以各相机在该模式的预设下为准。

仪表盘功能

遥控器内置多模卫星定位模块，可精准记录运动数据。连接 DJI Mimo App 后，可添加实时运动

数据（如速度、路线、方向及海拔等）至拍摄素材中并导出。

• 为避免 GPS 信号受到干扰，在室外空旷环境下使用遥控器。等待 1-2 分钟直至确认

GPS 信号满格后再使用。使用时保持遥控器正面朝上，请勿用手或其他物体挡住遥控器

的顶部。

• 由于遥控器信号在水下会受到影响，请勿在水下环境使用。

CHS

充电

打开遥控器机身的 USB-C 保护盖后，连接遥控器的 USB-C 接口与充电器充电。

状态指示灯

指示灯描述

关机状态下充电

绿灯常亮 6秒后熄灭充电完成

绿灯四闪充电中，76%-100%

绿灯三闪充电中，51%-75%

绿灯双闪充电中，26%-50%

绿灯闪烁充电中，0%-25%

系统状态

红灯三闪关机

蓝灯闪烁进入配对状态

工作状态

绿灯常亮进入拍摄就绪状态

绿灯灭一次拍照

红灯闪烁录像中

状态指示灯

CHS

规格参数

产品型号 OSMO-AF-336

蓝牙遥控器尺寸 40.5x38.6x20.5mm

重量 26 g

防水等级 IPX7

遥控距离 25 米*

GNSS GPS+BeiDou+Galileo+GLONASS

蓝牙

协议 BLE5.0

工作频率 2.402-2.480GHz

发射功率 < 4 dBm

电池

容量 270mAh

电池类型可充电锂离子电池组

充电方式连接 USB-C 接口（电压为 4.4V）

充电环境温度 0 ℃至 45℃

工作环境温度 -10℃至 45℃

* 在无干扰无遮挡实验室条件下测得。

Thiscontentissubjecttochangewithoutpriornotice.

DJIandOSMOACTIONaretrademarksofDJI.

https://www.dji.com/osmo-action-4/downloads

Contact

DJI SUPPORT

微信扫一扫

获取技术支持