Dell PowerEdge 1900 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerEdge™ 1900 Systems

Getting Started

With Your System

系统使用入门

開始使用系統

はじめに

시스템시작하기

www.dell.com | support.dell.com

Dell™ PowerEdge™ 1900 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell, Inc.; Intel and Xeon are registered trademarks of Intel Corporation;

Microsoft and Windows are registered trademark and Windows Server is a trademark of Microsoft Corporation; Red Hat is a registered trademark

of Red Hat, Inc.; SUSE is a registered trademark of SUSE LINUX Products GmbH.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model ECM01

February 2006 P/N GF501 Rev. A00

Getting Started With Your System 3

System Features

The major hardware and software features of your system include:

• One or two Dual-Core Intel

®

Xeon

®

Processors 5000 Sequence.

• Support for symmetric multiprocessing (SMP), which is available on systems with two Intel Xeon

processors. SMP greatly improves overall system performance by dividing processor operations

between independent processors. To take advantage of this feature, you must use an operating

system that supports multiprocessing.

NOTE: If you decide to upgrade your system by installing a second processor, you must order the

processor upgrade kits from Dell. Not all versions of the Intel Xeon processor will work properly as

additional processors. The upgrade kit from Dell contains the correct version of the processor and heat

sink.

• A minimum of 512 MB of 533 or 667 MHz (when available), Fully Buffered DIMMs (FBD),

upgradable to a maximum of 16 GB by installing combinations of 256-MB, 512-MB, 1-GB or 2-GB

memory modules in the eight memory module sockets on the system board.

• Support for up to six 3.5-inch, internal Serial-Attached SCSI (SAS) hard drives or six 3.5-inch,

internal SATA hard drives.

• Peripheral bay provides support for an optional optical drive and an optional half-height tape

backup unit (TBU).

• An optional single, 1.44-MB, 3.5-inch diskette drive.

• An optional CD, DVD, or combination CD-RW/DVD drive.

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management software if the top cover

is opened.

• An 800-W power supply.

• Six system cooling fans.

The system board includes the following features:

• Six PCI slots located in an expansion-card cage. Slots 1 and 2 are 3.3-V, 64-bit, 133-MHz PCI-X

slots; slot 3 is a 3.3-V, PCIe x8 lane; slots 4 through 6 are 3.3-V, PCIe x4 lanes. Expansion-card slots

2 through 6 accommodate full-height, full-length expansion cards. Slot 1 accommodates half-

length expansion cards. PCIe slots accommodate up to x8 expansion cards.

4 Getting Started With Your System

• Dedicated PCI slot for an optional integrated RAID controller card.

NOTE: System boot is not supported from an external device attached to a SAS or SCSI adapter, including

SAS 5/E, PERC 5/E, or PERC 4e/DC. Contact your technical support provider for the latest support information

about booting from external devices.

• An integrated Gigabit Ethernet NIC, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps data

rates.

• Six USB 2.0-compliant connectors (two on the front and four on the back) capable of supporting

a diskette drive, a CD-ROM or DVD-ROM drive, a keyboard, a mouse, or a USB flash drive.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz PCI video controller.

This video subsystem contains 16 MB of DDR SDRAM video memory (nonupgradable). Maximum

resolution is 1600 x 1200 with 64 K colors; true-color graphics are supported in the following

resolutions: 640 x 480, 800 x 600, 1024 x 768, 1152 x 864, and 1280 x 1024. When the optional RAC

is installed, the video resolution is 1024 X 768.

• Systems management circuitry that monitors operation of the system fans as well as critical system

voltages and temperatures. The systems management circuitry works in conjunction with the systems

management software.

• Standard baseboard management controller with serial access.

• Back-panel connectors include one serial, one video, four USB, and one NIC connector.

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see "Technical Specifications" on page 9.

Supported Operating Systems

• Microsoft

®

Windows Server™ 2003 Standard and Enterprise Editions

• Microsoft Windows Small Business Server 2003, Standard and Premium Editions

• Microsoft Windows Server 2003 Standard and Enterprise x64 Editions

•Red Hat

®

Enterprise Linux AS and ES (version 3 and version 4) for Intel x86

• Red Hat Enterprise Linux AS and ES (version 4) for Intel Extended Memory 64 Technology

(Intel EM64T)

•SUSE

®

Linux Enterprise Server 9 for Intel EM64T

Getting Started With Your System 5

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty

information may be included within this document or as a separate document.

• The

Hardware Owner’s Manual

provides information about system features and describes how to

troubleshoot the system and install or replace system components. The

Hardware Owner’s Manual

is available on the CDs that came with your system or from

support.dell.com

.

• CDs included with your system provide documentation and tools for configuring and managing

your system.

• Updates are sometimes included with the system to describe changes to the system, software, and/or

documentation.

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system or

documentation or advanced technical reference material intended for experienced users or

technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected,

see your Hardware Owner’s Manual.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time. Refer to the documentation

included with your system on installing the stabilizer feet on your system.

CAUTION: Installing the feet is necessary to provide a stable foundation for the system. Failure to install the feet

poses the risk of having the system tip over, possibly causing bodily injury or damage to the system.

CAUTION: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the

system by yourself.

6 Getting Started With Your System

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Installing the Stabilizer Feet

See the documentation included with your system on installing the system stabilizer feet.

Getting Started With Your System 7

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into each

connector. Be sure to tighten the screws (if any) on the monitor's cable connector.

Connecting the Power

Attach the system’s power cable to the cable clasp at the top of the power supply and connect it

to the system.

Plug the other end of the cable into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

8 Getting Started With Your System

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators should light.

Adjust the monitor’s controls until the displayed image is satisfactory.

Installing the Bezel

Install the bezel.

Getting Started With Your System 9

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships

with your system. To install an operating system for the first time, see the Quick Installation Guide.

Be sure the operating system is installed before installing hardware or software not purchased with

the system.

Technical Specifications

Processor

Processor type One or two Dual-Core Intel Xeon Processors 5000

Sequence

Expansion Bus

Bus type PCI, PCI-X, PCIe

Expansion slots

PCI-X

one full-height, half-length 3.3-V, 64-bit,

133-MHz (slot 1)

one full-height, full-length 3.3-V, 64-bit, 133-MHz

(slot 2)

PCIe

one x8 lane, 3.3-V (slot 3)

three x4 lanes, 3.3-V (slots 4 through 6)

Memory

Architecture 533 or 667 MHz (when available) Fully Buffered

DIMMs (FBD)

Memory module sockets eight 240-pin

Memory module capacities 256 MB, 512 MB, 1 GB, or 2 GB

Minimum RAM 512 MB (two 256-MB modules)

Maximum RAM 16 GB

Drives

Hard drives up to six 3.5-inch, internal, SAS or SATA

Diskette drive one optional internal 3.5-inch, 1.44-MB

optional external USB 3.5-inch, 1.44-MB

10 Getting Started With Your System

Optical drive one optional CD, DVD, or combination

CD-RW/DVD

NOTE:

DVD devices are data only.

optional external USB CD-ROM

optional external USB DVD-ROM

Flash drive optional external USB

Connectors

Back

NIC

TOE-capable RJ-45 (for integrated 1-GB NIC)

Serial

9-pin, DTE, 16550-compatible

USB

Four 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Video

Video type ATI ES1000 video controller; VGA connectors

Video memory 16 MB of DDR SDRAM

Power

AC power supply

Wattage

800 W

Voltage

90–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2320 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply for

10 ms or less

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Drives (continued)

Getting Started With Your System 11

Physical

Tower (without bezel)

Height

47.89 cm (18.85 in) with feet, no casters

Width

22.66 cm (8.92 in)

Depth

66.13 cm (26.04 in) does not include control

panel or bezel; control panel adds an additional

1.3 cm (.51 in)

Weight (maximum configuration)

49.9 kg (110 lb)

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

contact your technical support provider.

Temperatur e

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 G from 5–350Hz for 2 min in the Z axis

Storage

1.54 G from 10–250 Hz for 15 min in all

orientations

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

12 Getting Started With Your System

www.dell.com | support.dell.com

Dell™ PowerEdge™ 1900 系统

系统使用入门

注、注意和警告

注：

注表示可以帮助您更好地使用计算机的重要信息。

注意：

注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：

警告表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

和

DELL

徽标是

Dell, Inc.

的商标；

Intel

和

Xeon

是

Intel Corporation

的注册商标；

Microsoft

和

Windows

是

Microsoft Corporation

的注册商标，

Windows Server

是

Microsoft Corporation

的商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

SUSE LINUX Products GmbH

的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外

的其它商标和产品名称不拥有任何专有权。

型号 ECM01

2006

年

2

月

P/N GF501

修订版

A00

系统使用入门 15

系统配置

系统的主要硬件和软件配置包括：

•

一个或两个双核心

Intel

®

Xeon

®

处理器

5000

序列。

•

支持对称多处理

(SMP)

，配备两个

Intel Xeon

处理器的系统具有此功能。

SMP

通过在独立的

处理器之间分配处理器操作，从而极大地改善了系统整体性能。要使用此功能，必须使用支

持多处理的操作系统。

注：如果您准备安装第二个处理器来升级系统，则必须向 Dell 订购处理器升级套件。并非所有

版本的 Intel Xeon 处理器均可作为附加处理器正常工作。Dell 的升级套件包含正确版本的处理器

和散热器。

•

至少

512 MB

的

533

或

667 MHz

（可用时）全缓冲

DIMM (FBD)

，通过在系统板上的八个内

存模块插槽中安装

256 MB

、

512 MB

、

1 GB

或

2 GB

内存模块组合，最大可升级至

16 GB

。

•

支持多达六个

3.5

英寸、内部串行连接

SCSI (SAS)

硬盘驱动器或六个

3.5

英寸、内部

SATA

硬盘驱动器。

•

外围设备托架可支持一个可选的光盘驱动器和一个可选的半高磁带备份装置

(TBU)

。

•

一个可选的

1.44 MB 3.5

英寸软盘驱动器。

•

一个可选的

CD

、

DVD

或组合

CD-RW/DVD

驱动器。

注：DVD 设备仅用于数据。

•

防盗开关，在顶盖被打开时会向相应的系统管理软件发送信号。

•

一个

800W

电源设备。

•

六个系统冷却风扇。

系统板包含以下配置：

•

位于扩充卡固定框架上的六个

PCI

插槽。插槽

1

和

2

是

3.3 V

、

64

位、

133 MHz PCI-X

插槽；

插槽

3

是一个

3.3 V

、

PCIe x8

信道插槽；插槽

4

至插槽

6

是

3.3 V

、

PCIe x4

信道插槽。扩充

卡插槽

2

到

6

中可以安装全高、全长扩充卡。插槽

1

可以安装半长扩充卡。

PCIe

插槽可以安

装多达

x8

个扩充卡。

16 系统使用入门

•

专用

PCI

插槽，用于安装可选的集成

RAID

控制器卡。

注：不支持从连接到 SAS 或 SCSI 适配器的外部设备引导系统，包括 SAS 5/E、PERC 5/E 或

PERC 4e/DC。有关支持从外部设备引导的最新信息，请与您的技术支持提供商联系。

•

一个集成的千兆位以太网

NIC

，可支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

•

六个

USB 2.0

兼容连接器（两个在正面，四个在背面），可以支持软盘驱动器、

CD-ROM

或

DVD-ROM

驱动器、键盘、鼠标或

USB

快擦写驱动器。

•

可选的远程访问控制器

(RAC)

，用于远程系统管理。

•

VGA

兼容集成视频子系统，带有

ATI ES1000

、

33 MHz PCI

视频控制器。此视频子系统包含

16 MB

的

DDR SDRAM

视频内存（不可升级）。使用

64 K

色时最大分辨率为

1600

x

1200

；

以下分辨率支持真彩色图形：

640

x

480

、

800

x

600

、

1024

x

768

、

1152

x

864

和

1280

x

1024

。

如果安装了可选的

RAC

，则视频分辨率为

1024

x

768

。

•

系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。系统管理电路需要与系统管理

软件配合工作。

•

标准底板管理控制器，支持串行访问。

•

背面板连接器包括一个串行连接器、一个视频连接器、四个

USB

连接器和一个

NIC

连接器。

•

前面板连接器包括一个视频连接器和两个

USB

连接器。

•

前面板

1

x

5 LCD

显示屏，用于显示系统

ID

和错误信息。

•

系统

ID

按钮，位于前面板和背面板上。

有关特定配置的详细信息，请参阅第

21

页的 “技术规格”。

支持的操作系统

•

Microsoft

®

Windows Server

™

2003

标准版和企业版

•

Microsoft Windows Small Business Server 2003

标准版和高级版

•

Microsoft Windows Server 2003

标准版和企业版（

64

位）

•

用于

Intel x86

的

Red Hat

®

Enterprise Linux AS

和

ES

（第

3

版和第

4

版）

•

用于

Intel 64

位扩展内存技术

(Intel EM64T)

的

Red Hat Enterprise Linux AS

和

ES

（第

4

版）

•

用于

Intel EM64T

的

SUSE

®

Linux Enterprise Server 9

系统使用入门 17

您可能需要的其它信息

警告：《产品信息指南》提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

•

《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换

系统组件。《硬件用户手册》可在随系统提供的

CD

或在

support.dell.com

上获得。

•

随系统附带的

CD

提供了用于配置和管理系统的说明文件和工具。

•

系统有时附带更新，用于说明对系统、软件和／或说明文件所做的更改。

注：请始终检查

support.dell.com

上的更新信息并首先进行阅读，因为该网站上的信息常常会取代

其它说明文件中的信息。

•

系统可能会附带发行说明或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的

用户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的步骤有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

安装和配置

警告：在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。请参阅随系统提供的说明文件在系统上安装稳定支脚。

警告：要为系统提供稳固的基础，需要安装支脚。如果未安装支脚，可能存在导致系统倾翻的危险，

从而可能造成人身伤害或损坏系统。

警告：无论何时您需要抬起系统，均需找他人协助。为了避免造成伤害，请勿尝试自行抬起系统。

18 系统使用入门

打开系统包装

打开系统包装并识别每项物品。

妥善保管所有运输包装材料，以备将来使用。

安装稳定支脚

参阅随系统提供的说明文件安装系统稳定支脚。

ページが読み込まれています...

Dell PowerEdge 1900 クイックスタートガイド

Dell PowerEdge 1900 クイックスタートガイド

関連論文

その他のドキュメント