Dell PowerEdge RAID Controller 6i クイックスタートガイド

Dell™ PowerEdge™

Expandable RAID Controller x

Removing and Installing the

Battery and Battery Cable

on PERC Controllers

在 PERC 控制器上拆装电池和电池电缆

拆裝 PERC 控制器的電池和電池電纜

Retrait et installation de la batterie

et de son câble sur les contrôleurs PERC

Entfernen und Installieren des Akkus und

des Akkukabels bei PERC-Controllern

PERC コントローラのバッテリーとバッテ

リーケーブルの取り外しと取り付け

PERC

컨트롤러의 전지 및 전지

케이블 제거 / 설치

Установка и удаление батареи и кабеля

батареи на контроллерах

PERC

Extracción e instalación de la batería y el cable

de la batería en controladoras PERC

Model UCP-50 and UCP-51

Dell™ PowerEdge™

Expandable RAID Controller x

Removing and Installing the

Battery and Battery Cable

on PERC Controllers

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, Dell Precision, and PowerEdge, are trademarks

of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks

and trade names other than its own.

Model UCP-50 and UCP-51

November 2007 P/N XR434 Rev. A00

Removing and Installing the Battery and Battery Cable on PERC Controllers 3

Removing and Installing the

Battery and Battery Cable

on PERC Controllers

This document contains information on removing and installing the battery,

battery cable, and memory module on Dell™ PowerEdge™ Expandable RAID

Controllers (PERC).

• See page 4 for PERC

x

/E, where

x

is the generation of the card (i.e., 5, 6, etc.)

battery removal and installation procedures

• See page 10 for PERC

x

/i battery removal and installation procedures

Important Safety Information

CAUTION: Any installation that requires removal of the system cover is intended solely

to be performed by trained service technicians. See the Product Information Guide that

came with your system for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTE: See the Product Information Guide that came with your system for complete

information about U.S. Terms and Conditions of Sale, Limited Warranties and

Returns, Export Regulations, Software License Agreement, Safety, Environmental

and Ergonomic Instructions, Regulatory Notices, and Recycling Information.

4 Removing and Installing the Battery and Battery Cable on PERC Controllers

Removing the Transportable Battery Backup Unit (TBBU)

from a PERC x/E Adapter

This section describes the procedure to remove the TBBU from a PERC

x

/E

Adapter installed in a system.

NOTE: The TBBU on the PERC x/E Adapter consists of a dual in-line memory

module (DIMM) and a battery backup unit (BBU).

1

Perform a controlled shutdown of the system in which the PERC

x

/E

Adapter is installed, as well as any attached storage enclosures, and remove

the PERC

x

/E Adapter from the system. See the

Dell PowerEdge Expandable

RAID Controller x/i and x/E User’s Guide

for more information.

2

Visually inspect the controller and determine whether the dirty cache LED

on the memory module is turned on. See Figure 1. If the LED is turned on,

reinsert the controller into the system, replace the system cover, reconnect

the system to the electrical outlet, turn on the system, and repeat step 1.

Figure 1. PERC x/E Adapter Dirty Cache LED Location

CAUTION: Running a system without the system cover installed may cause

damage due to improper cooling.

1 memory module 2 battery

3 dirty cache LED 4 PERC x/E Adapter

4

3

1

2

Removing and Installing the Battery and Battery Cable on PERC Controllers 5

3

Remove the TBBU assembly from the PERC

x

/E Adapter by pressing down

on the tabs at each edge of the memory module connector and lifting the

TBBU off the adapter.

4

Disconnect the battery cable from the memory module.

NOTE: Do not exert excessive pressure on the connector on the memory

module while removing the memory module.

5

Detach the battery from the memory module by pressing out on the

battery clips inserted through the memory module and rotating the

battery off the memory module. See Figure 2.

Figure 2. Removing the BBU

1 memory module 2 battery

2

1

6 Removing and Installing the Battery and Battery Cable on PERC Controllers

Installing the New BBU and Battery Cable

This section describes the installation of the BBU and battery cable onto the DIMM

of a PERC

x

/E Adapter.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before performing any

procedure, see your Product Information Guide for complete information about

safety precautions, working inside the computer, and protecting against

electrostatic discharge

.

1

Unpack the BBU and follow all antistatic procedures.

NOTE: All work must be performed at an Electrostatic Discharge (ESD)-safe

workstation to meet the requirements of EIA-625—"Requirements For

Handling Electrostatic Discharge Sensitive Devices." All actions must be

performed following the IPC-A-610 latest revision ESD recommended

practices.

NOTE: Handle all sensitive components in a static-safe area. If possible,

use antistatic floor pads and work bench pads.

NOTE: When unpacking a static sensitive component from its shipping

carton, do not remove the component from the antistatic packing material

until you are ready to install the component. Just before unwrapping the

antistatic package, be sure to discharge static electricity from your body.

2

With the memory module removed from the controller, insert one end

of the battery cable (the red, white, yellow, and green wires) into the

connector on the memory module and the other end into the connector

on the battery.

NOTE: Do not exert excessive pressure on the connector on the memory

module while installing the memory module.

Removing and Installing the Battery and Battery Cable on PERC Controllers 7

3

Place the top edge of the battery over the top edge of the memory module

so that the arms on the side of the battery fit into their sockets on the

memory module. See Figure 3.

CAUTION: Electrostatic discharge can damage sensitive components.

Always use proper antistatic protection when handling components.

Touching components without proper grounding can damage the equipment.

Figure 3. Installing the BBU and Battery Cable

4

Place the PERC

x

/E Adapter on a flat, clean, and static–free surface.

5

Mount the memory module on the controller memory socket like a

standard DIMM. See the section "Installing the TBBU on a PERC x/E

Adapter" for more information.

The memory module is mounted flush with the board so that the memory

module is parallel to the board when installed.

6

Press the memory module firmly into the memory socket. As you press the

memory module into the socket, the BBU clicks into place, indicating that

the controller is firmly seated in the socket, and the arms on the socket fit

into the notches to hold the memory module securely.

1 memory module 2 connector on the memory module 3 battery cable

4 battery 5 connector on the battery

2

3

4

1

5

8 Removing and Installing the Battery and Battery Cable on PERC Controllers

Installing the TBBU on a PERC x/E Adapter

This section describes the procedure to install the memory module on a PERC

x

/E Adapter.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before performing any

procedure, see your Product Information Guide for complete information about

safety precautions, working inside the computer, and protecting against

electrostatic discharge.

NOTE: The TBBU on the PERC x/E Adapter consists of a dual in-line memory

module (DIMM) and a battery backup unit (BBU).

1

Remove the memory module in an antistatic environment.

NOTE: When unpacking a static-sensitive component from its shipping

carton, do not remove the component from the antistatic packing material

until you are ready to install the component. Just before unwrapping the

antistatic package, be sure to discharge static electricity from your body.

NOTE: Handle all sensitive components in a static-safe area. If possible,

use antistatic floor pads and work bench pads.

NOTE: Never touch the gold leads and do not bend the memory module.

2

Align the memory module so that the keyed edge of the memory module is

placed exactly on top of the physical divider on the memory socket of the

controller. This will avoid damage to the memory module.

3

Insert the memory module on the memory socket of the controller and

apply a smooth, downward pressure on both ends or on the middle of the

memory module until the retention clips fall into the allotted slots on

either side of the memory module. Figure 4 displays the installation of

a memory module on a PERC

x

/E Adapter.

Removing and Installing the Battery and Battery Cable on PERC Controllers 9

Figure 4. Installing a Dual In-line Memory Module

1 memory module 2 memory socket

3PERC x/E Adapter 4 retention clip

1

2

4

3

10 Removing and Installing the Battery and Battery Cable on PERC Controllers

Removing the DIMM from a PERC x/i Controller

This section describes the procedure to remove the memory module from

aPERC

x

/i Adapter or PERC

x

/i Integrated controller installed in a system.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before performing any

procedure, see your Product Information Guide for complete information about

safety precautions, working inside the computer, and protecting against

electrostatic discharge.

NOTICE: Depending on the generation of your PERC card, the DIMM memory

module may not be removable. PERC 5/i cards include a removable DIMM module.

PERC 6/i cards have an integrated DIMM module which cannot be removed. Do not

attempt the following procedure on a PERC 6/i adapter or integrated controller card.

1

Perform a controlled shutdown of the system in which the PERC

x

/i

controller is installed and remove the PERC

x

/i controller from the system.

See the

Dell PowerEdge Expandable RAID Controller x/i and x/E User’s

Guide

for more information.

CAUTION: Running a system without the system cover installed may cause

damage due to improper cooling.

2

Remove the memory module by pressing down on the tabs at each edge

of the memory module connector and lifting the memory module off the

controller.

NOTE: Do not exert excessive pressure on the connector on the memory

module while removing the memory module.

NOTE: The location of the PERC x/i Integrated controller varies from system

to system. See the Hardware Owner’s Manual included with the system for

specific information on where the PERC x/i Integrated controller is located.

Removing and Installing the Battery and Battery Cable on PERC Controllers 11

Disconnecting the BBU from a PERC x/i Controller

This section describes the procedure to disconnect the BBU on a PERC

x

/i

Adapter or PERC

x

/i Integrated controller while it is installed in a system.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before performing any

procedure, see your Product Information Guide for complete information about

safety precautions, working inside the computer, and protecting against

electrostatic discharge.

NOTE: PERC x/i Adapters installed in Dell Precision™ workstations or PowerEdge

SC servers do not have a BBU.

1

Perform a controlled shutdown of the system in which the PERC

x

/i

controller is installed.

2

Disconnect the system from the electrical outlet and remove the system

cover.

NOTE: See the Hardware Owner’s Manual included with the system for more

information on removing and reinstalling the system cover.

3

Locate the PERC

x

/i controller in the system and visually inspect the

controller to determine whether the dirty cache LED on the controller is

turned on. If the LED is turned on, replace the system cover, reconnect

the system to power, turn the system on and repeat steps 1 and 2.

CAUTION: Running a system without the system cover installed may cause

damage due to improper

cooling.

4

Locate the battery cable connection next to the memory module on the

controller, and disconnect the battery.

See the

Hardware Owner’s Manual

included with the system for information

on removing the BBU from the system chassis. The location of the TBBU

for the PERC

x

/i controller varies from system to system.

12 Removing and Installing the Battery and Battery Cable on PERC Controllers

Installing the DIMM and BBU to a PERC x/i controller

This section describes the installation of the TBBU on a PERC

x

/i Adapter or

PERC

x

/i Integrated controller.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before performing any

procedure, see your Product Information Guide for complete information about

safety precautions, working inside the computer, and protecting against

electrostatic discharge.

NOTICE: Depending on the generation of your PERC card, the DIMM memory

module may not be removable. PERC 5/i cards include a removable DIMM module.

PERC 6/i cards have an integrated DIMM module which cannot be removed. Do not

attempt the following procedure on a PERC 6/i adapter or integrated controller card.

NOTE: Charge the PERC x battery before initial use to attain full functionality.

1

Unpack the DIMM and BBU and follow all antistatic procedures.

NOTE: All work must be performed at an Electrostatic Discharge (ESD)-safe

workstation to meet the requirements of EIA-625—"Requirements For Handling

Electrostatic Discharge Sensitive Devices." All actions must be performed

following the IPC-A-610 latest revision ESD recommended practices.

NOTE: Handle all sensitive components in a static-safe area. If possible,

use antistatic floor pads and work bench pads.

NOTE: When unpacking a static sensitive component from its shipping

carton, do not remove the component from the antistatic packing material

until you are ready to install the component. Just before unwrapping the

antistatic package, be sure to discharge static electricity from your body.

2

Locate the battery cable connection next to the memory module on the

controller, and connect the battery.

NOTE: Do not use excessive pressure on the connector on the memory

module while installing the memory module.

3

Align the memory module so that the keyed edge of the memory module

is placed exactly on top of the physical divider on the memory socket of the

controller. This will avoid damage to the memory module.

4

Insert the memory module on the memory socket of the controller and

apply a smooth, downward pressure on both ends or on the middle of the

memory module until the retention clips fall into the allotted slots on

either side of the memory module.

Dell™ PowerEdge™

可扩充

RAID

控制器

x

在

PERC

控制器上拆装电

池和电池电缆

注、注意和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

注意：“注意”表示可能会损坏硬件或导致数据丢失，并告诉您如何避免

此类问题。

警告：“警告”表示可能会出现导致财产损失、人身伤害甚至死亡的情况。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标、

Dell Precision

和

PowerEdge

是

Dell Inc.

的商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

UCP-50

和

UCP-51

2007

年

11

月

P/N XR434

修订版

A00

在

PERC

控制器上拆装电池和电池电缆 15

在

PERC

控制器上拆装电池和电

池电缆

本说明文件介绍如何在

Dell™ PowerEdge™

可扩充

RAID

控制器

(PERC)

上拆装电池、电池电缆和内存模块的信息。

•

有关

PERC

x

/E

（其中

x

表示第几代卡，如

5

、

6

等）电池拆装过程的信

息，请参阅第

16

页

•

有关

PERC

x

/i

电池拆装过程的信息，请参阅第

22

页

重要安全信息

警告：任何需要拆卸系统护盖的安装均只限经过培训的维修技术人员进行。

有关安全预防措施、拆装计算机内部组件以及防止静电释放的完整信息，

请参阅随系统提供的

《产品信息指南》。

注：有关美国销售条款和条件、有限保修与退回规定、出口法规、软件许

可协议以及安全、环境和人机工程学说明、管制通告、循环利用信息等的完

整内容，请参阅随系统提供的《产品信息指南》。

16 在

PERC

控制器上拆装电池和电池电缆

从

PERC x/E

适配器上卸下移动式电池备用单元

(TBBU)

本节介绍从安装在系统中的

PERC

x

/E

适配器上卸下

TBBU

的过程。

注：

PERC x/E

适配器上的

TBBU

由一块双列直插式内存模块

(DIMM)

和一个

电池备用单元

(BBU)

构成。

1

对安装了

PERC

x

/E

适配器的系统以及任何连接的存储设备执行从容

关闭，并从系统中卸下

PERC

x

/E

适配器。有关详细信息，请参阅

Dell PowerEdge Expandable RAID Controller x/i and x/E User

’s

Guide

（

Dell PowerEdge

可扩充

RAID

控制器

x/i

和

x/E

用户指南）。

2

通过外观来检查控制器，并确定内存模块上的已占用高速缓存

LED

是

否亮起。请参阅图

1

。如果

LED

已亮起，则将控制器重新插入系统中，

装回系统护盖，将系统重新连接至电源插座，打开系统，然后重复

步骤

1

。

图

1. PERC x/E

适配器已占用高速缓存

LED

位置

警告：如果运行系统时未安装系统护盖，则可能会由于冷却不当而导致设

备损坏。

1

内存模块

2

电池

3

已占用高速缓存

LED

4

PERC x/E

适配器

4

3

1

2

在

PERC

控制器上拆装电池和电池电缆 17

3

按下内存模块连接器两侧的卡舌并从适配器中提起内存模块

TBBU

，

从

PERC

x

/E

适配器中卸下

TBBU

部件。

4

从内存模块上断开电池电缆连接。

注：卸下内存模块时，请勿过度用力挤压内存模块上的连接器。

5

向外按压插入内存模块中的电池固定夹并旋转电池使之脱离内存

模块，从内存模块中卸下电池。请参阅图

2

。

图

2.

卸下

BBU

1

内存模块

2

电池

2

1

18 在

PERC

控制器上拆装电池和电池电缆

安装新

BBU

和电池电缆

本节介绍如何将

BBU

和电池电缆安装到

PERC

x

/E

适配器的

DIMM

中。

警告：只有经过培训的维修技术人员才有权卸下系统护盖并拆装系统内部

的任何组件。在执行任何过程之前，请参阅《产品信息指南》，获取有关安

全预防措施、拆装计算机内部组件以及防止静电释放的完整信息

。

1

打开

BBU

包装，并遵循所有防静电过程。

注：所有工作均必须在无静电释放

(ESD)

的工作站上执行，以满足

EIA-625 -

“处理静电释放敏感设备需求”的要求。执行所有操作时，必须遵循

IPC-A-610

Dell PowerEdge RAID Controller 6i クイックスタートガイド

Dell PowerEdge RAID Controller 6i クイックスタートガイド

他の言語で