Trimming with comb
1 Turn the Precision Zoom Lock adjustment
ring to the desired setting. The selected
setting is the setting in the centre of the
adjustment ring. (Fig. 4)
See the table below for an overview of
the settings and the resulting hair lengths.
Setting Resulting
hair length
Setting Resulting
hair length
. 0.5 mm . 5.5mm
1 1 mm 6 6mm
. 1.5 mm . 6.5mm
2 2 mm 7 7mm
. 2.5 mm . 7.5mm
3 3 mm 8 8mm
. 3.5 mm . 8.5mm
4 4 mm 9 9mm
. 4.5 mm . 9.5mm
5 5 mm 10 10mm
Note: When you trim for the rst time, start at the
highest setting (10) to familiarise yourself with the
appliance.
2 Switch on the appliance.
3 To trim most effectively, move the trimmer
against the hair growth direction. Make
sure the surface of the comb always stays in
contact with the skin (Fig. 5).
4 If a lot of hair has accumulated in the beard
trimming comb, remove the comb and
blow and/or shake the hair out of it. The
selected setting does not change when you
do this (Fig. 6).
Trimming at the unique ‘stubble look’
setting
1 To create a ‘stubble look’, trim with the beard
trimming comb set to setting 1 (Fig. 7).
Trimming without comb
Use the trimmer without beard trimming comb to
trim full beards and single hairs.
Be careful when you trim without comb because
the cutting element removes every hair it
touches.
1 Pull the beard trimming comb off the
appliance. (Fig. 8)
2 Switch on the appliance.
3 Make well-controlled movements. Touch the
hair lightly with the trimmer (Fig. 9).
Cleaning
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as alcohol, petrol or
acetone to clean the appliance.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 Wipe the housing of the appliance with a dry
cloth.
Never immerse the appliance in water or rinse it
under the tap.
3 Remove the trimming comb and clean it with
the brush.
4 Remove the cutting unit by pushing against
the teeth of the cutting unit. Clean it with the
brush or rinse it under the tap (Fig. 10).
5 Shake off excess water. Place the cutting unit
back by inserting the lug of the cutting unit
into the guiding slot. (Fig. 11)
6 Push the cutting unit back onto the appliance
(‘click’).
Replacement
Only replace a worn or damaged cutting unit with
an original Philips cutting unit, available from
authorised Philips service centres.
1 Open the cutting unit.
2 Remove the old cutting unit by pushing
against the teeth of the cutting unit. (Fig. 10)
3 Insert the lug of the new cutting unit into the
guiding slot (Fig. 11).
4 Push the cutting unit back onto the appliance
(‘click’) (Fig. 12).
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care centre in your country.
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 13).
- The built-in rechargeable battery contains
substances that may pollute the environment.
Always remove the battery before you
discard and hand in the appliance at an ofcial
collection point. Dispose of the battery at an
ofcial collection point for batteries. If you have
trouble removing the battery, you can also take
the appliance to a Philips service centre. The
staff of this centre will remove the battery for
you and will dispose of it in an environmentally
safe way. (Fig. 14)
Removing the rechargeable battery
Only remove the rechargeable battery if it is
completely empty.
1 Disconnect the appliance from the mains and
let the appliance run until the motor stops.
2 Insert a screwdriver in the hair chamber to
separate the housing part (Fig. 15).
3 Cut the wires close to the battery with a pair
of household scissors (Fig. 16).
4 Remove the rechargeable battery.
Do not connect the appliance to the mains again
after you have opened it.
Guarantee and support
If you need service or support, please visit
www.philips.com/support or read the separate
worldwide guarantee leaet.
简体中文
简介
感谢您的惠顾,欢迎光临飞利浦!
为了您能充分享受飞利浦提供的支持,请在
www.philips.com/welcome 上注册您的产品。
基本说明 (图 1)
1 修剪梳
2 修剪部件
3 精确缩放锁 调整环
4 开/关滑钮
5 产品插座接口
6 清洁刷
7 产品插头
8 具有充电指示灯的电源适配器
注意事项
使用本产品之前,请仔细阅读本使用说明书,
并妥善保管以备日后参考。
危险
- 确保电源适配器干燥。
警告
- 电源适配器内含有一个变压器。切勿自行
更换插头,否则将导致严重后果。
- 器具不打算由有肢体、感官或精神能力缺
陷或缺少使用经验和知识的人(包括儿
童)使用,除非有负责他们安全的人对他
们进行与器具使用有关的监督或指导。应
照看好儿童,确保他们不玩耍本器具。
注意
- 切勿将本产品浸入水中或在水龙头下冲
洗。仅修剪部件可在水龙头下冲洗。
- 必须在 5 摄氏度至 35 摄氏度之间的温度
下使用、存放和为本产品充电。
- 只能使用随附的适配器。
- 如果适配器已损坏,则务必更换原装型号
适配器,以免发生危险。
- 本产品仅限于修剪人体须发,不可用于任
何其它用途。
- 如果修剪部件或修理梳齿损坏或损毁,
请勿再使用本产品,否则可能对人体造成
伤害。
电磁场 (EMF)
本飞利浦产品符合所有有关暴露于电磁场的适
用标准和法规。
概述
- 本产品配有一个自动电压选择器,可使用
100 至 240 伏范围内的电源电压。
- 电源适配器可将 100-240 伏的电压转换为
24 伏以下的安全低电压。
充电
首次使用前或长时间不用之后,请为产品充
满电。
本产品充满电约需要 10 小时。
充满电后,产品可在不接电源的情况下工作长
达 45 分钟。
注意: 出于安全考虑,产品只能在不接电源的
情况下使用。使用前,请确保产品已充满电。
1 确保产品电源已关闭。 (图 2)
2 将产品插头插入本产品。 (图 3)
3 将电源适配器插入电源插座。
, 电源适配器上的充电指示灯呈绿色持续亮
起,表示产品正在充电。
注意: 产品充满电后,适配器上的充电指示
灯不会改变颜色及熄灭。