Flashforge SZ20-ZN Creator 3 FDM 3D Printer ユーザーガイド

カテゴリー
印刷
タイプ
ユーザーガイド
1. Hot! Avoid touching the heating nozzle and heating build plate in operation.
Please refer to FlashForge official website www.flashforge.com to download
the newest User's Guide, Software and Instruction Videos.
(Support-Support Center-Select a Product)
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
Download
1. 高温危险!打印机喷嘴和打印平台在工作时会被加热,请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
前往闪铸科技官方网站 www.sz3dp.com ,可以在[ 技术支持 ] 页面下载用户使
用手册、切片软件等资料,或查看相关操作视频。
资料下载
快速启动指
Quick Start Guide
SZ20-ZN/EN-A02 / 金刚狼3
Creator 3
This guide is only applicable to FLASHFORGE Creator 3 3D printer
本指南仅适用于闪铸科技金刚狼3 3D打印机
中文 P17
01
1. Cut off packaging ties, and tear off
stretch wrap.
2. Lift outer packing box.
3. Remove top foam. 4. Remove foam around the printer.
5. Unrip tapes on four corners of the printer,
take bubble pack down.
6. Remove tapes on the top, open head cover.
02
7. Take top parts and foam out. 8. Remove the blue fastening tape.
9. Open the front door and take out the front foam which should contain two filament spools and
two waste boxes.
10. Remove clips on timing belt of X-axis and Y-axis.
03
11. Plug power cable into the input on the back and turn on the power switch. Tap[Tools], [Manual].
ToolsPreheatBuild
SettingStatus About
FilamentLevelHomeManual
HOME
<
14. Now you’ve unpacked your Creator 3.
12. Tap [Z-] to partially elevate the build plate. 13. Remove bottom foam pieces.
<
X
X
Y
Z
0.00
0.00
0.00
0.00
Y +
X -
X -
X +
X +
Z -
Z +
Y -
04
Getting to Know Your Creator 3
1. Touch Screen 2. USB Stick Input 3. Touch Screen Buttom 4. Right Extruder
13. Turbofan Baffle 14. Network Input 15. Power Switch 16. Power Input
9. Leveling Nut 10. Filament Cartridge Cover 11. Cartridge Cover Handle 12. Nozzle
5. Left Extruder 6. Nozzle Brush 7. Waste Box 8. Build Plate
05
Waste Box
Nozzle Brush
1. Hot! Avoid touching the heating nozzle and heating build plate in operation.
Please refer to FlashForge official website www.flashforge.com to download
the newest User's Guide, Software and Instruction Videos.
(Support-Support Center-Select a Product)
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
Download
1. 高温危险!打印机喷嘴和打印平台在工作时会被加热,请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
前往闪铸科技官方网站 www.sz3dp.com ,可以在[ 技术支持 ] 页面下载用户使
用手册、切片软件等资料,或查看相关操作视频。
资料下载
快速启动指
Quick Start Guide
SZ20-ZN/EN-A01
中文
/ 金刚狼3
Creator 3
This guide is only applicable to FLASHFORGE Creator 3 3D printer
本指南仅适用于闪铸科技金刚狼3 3D打印机
06
How to use the leveling nuts
Rotate the nut clockwise
Rotate the nut anticlockwise
ToolsPreheatBuild
Setting Status About
Filament Level Home Manual
HOME
<
Language
WIFI
WLan hotspot
Door Opened Pause
Door Opened Detector
English 简体中文
English
日本語
繁體中文
Deutsch
07
ToolsPreheatBuild
Setting Status About
Filament Level Home Manual
HOME
<
1. Tap[Tools], tap[Level]to level the build plate.
2. Wait for the extruder and the build plate moving, after moving completed, choose to use which
extruder to level the build plate: left or right.
3. After leveling extruder confirmed,extruder will move to the first point to verify the distance
between nozzle and build plate. If verify completed, extruder will move to the second point to
verify the distance.
4. If the distance is not appropriate, please follow the prompts to adjust again till you see [OK] button.
Repeat steps 4 to level the second and third points. Then tap [Finish] to exit.
Select the extruder
Level
Left Extruder Right Extruder
<
Please wait...Initializing
<
Wait
Verifying the distance between nozzle
and plate...
<
OK
Verify Next
Turn the nut counterclockwise 90°
Wait
Verify Next
Wait
Turn the nut clockwise 45°
08
1. Take out waste box, hang it on the hook
beside build plate. (One waste box on
each side)
2. Take out nozzle brush, install it on
mounting base. (One nozzle brush
on each side)
Install Waste box and Nozzle brush
Hook
Hook
09
1. Open the filament cover.
2. Insert the filament into filament intake.
3. Notice: For filament convenient rotation, please install filament follow the direction shown
in the picture.
When installing filament on the left side, please unload filament anticlockwise;
when installing filament on the right side, please unload filament clockwise.
Install Filament
Filament
intake
10
Press here
5. Press the spring presser, put filament
vertically into the left filament intake to
the bottom.
4. Insert filament into filament intake
continuously until filament goes through
filament guidetube.
6. Insert filament guidetube into filament
intake to fix.
7. Put the spool of filament on the spool
holder, close the filament cover.
11
1. Tap[Tools], [Filament] to enter the filament interface.
2. Flip the switch after corresponding extruder to
load corresponding extruder.
3. Tap[Begin], the extruder will start heating.
<
Load Unload
Begin
Left Extruder
Right Extruder
Left Extruder
Right Extruder
<
Cancel
Left Extruder is Heating... Right Extruder is Heating...
69 / 220℃ 69 / 220℃
31% 31%
ToolsPreheatBuild
Setting Status About
Filament Level Home Manual
HOME
<
Load Filament
<
Done
Loading started, push filament vertically
into extruder and press [Done] when you
see filament come out of the extruder
4. Once heated, filament will be drawn through the extruder. Continue extruding until the extruder
provides a steady flow of filament. Tap [Done], go back. Tap leftwards arrow to go back to the
home screen.
Attetion: If extruder can not unload in a long time, please check if you have inserted filament
into the bottom of extruder.
Left Extruder Heated Right Extruder Heated
12
ToolsPreheatBuild
Setting Status About
Filament Level Home Manual
HOME
<
<
Wait
Please wait...
Auto calibration.
Please operate under the guidance of customer service for the first calibration.
Calibration
Door Opened Remind
Startup Sound
Left Filament Check
Right Filament Check
Calibration
1. Tap [Z-axis calibration] and wait for Z-axis calibration of extruder and build plate.
Do not interrupt during the calibration process.
Tap [Tools], tap [Setting], tap [calibration] in setting page.
Please level before Z-axis calibration.
Please refer to the 06 page for leveling
Z Calibration
Z Calibration
X Calibration
Y Calibration
13
1. Tap [X-axis calibration] and wait for extruders heating up. After heating up till target temperature,
2 lines will be printed in sequence. Check if the 2 lines are aligned after printing. Meanwhile, the
pop-up window will appear.
Check if the lines printed by 2 extruders aligned on X-axis to judge if the extruders
on the same X-axis.
2. If the 2 lines are totally aligned, Tap [Yes], X-axis calibration is done. If the 2 lines are not totally
aligned, Tap [No]. Adjust position of extruders according to actual situation. After that, clean the
filament on build plate and Tap [Recalibration]. Repeat step 2 till the 2 lines are totally aligned.
<
X Calibration
Next
Recalibration
Skip
Reset OK Right Extruder is printing the 1st
baseline then left extruder will print
the 1st alignment line.
X Calibration
<
X Calibration
Next
Adjust deviation,
Press [Recalibration]
Deviation:0:00
Skip
Reset OK
Recalibration
14
Check if the lines printed by 2 extruders aligned on Y-axis to judge if the extruders
on the same Y-axis.
2. If the 2 lines are totally aligned, Tap [Yes], Y-axis calibration is done. If the 2 lines are not totally
aligned, Tap [No]. Adjust position of extruders according to actual situation. After that, clean the
filament on build plate and Tap [Recalibration]. Repeat step 2 till the 2 lines are totally aligned.
1. Tap [Y-axis calibration] and wait for extruders heating up. After heating up till target temperature,
2 lines will be printed in sequence. Check if the 2 lines are aligned after printing. Meanwhile, the
pop-up window will appear.
<
Y Calibration
Right Extruder is printing the 1st
baseline and then left extruder will print
the 1st alignment line.
Y Calibration
<
Y Calibration
Adjust deviation,
Press [Recalibration]
Deviation:0:00
OK
Next
Skip
Reset
Recalibration
OK
Next
Recalibration
Skip
Reset
15
ToolsPreheatBuild
1. Tap [Build]. 2. Tap [Local memory] to choose print files.
3. Choose the preset print file [PG.gx]. 4. Tap [Build].
5. The printer starts to heat up and will start printing after heating completed.
<
None
6834Mb2.7Mb
PG.gx PG
Total: 1 hr 48 min
Build Copy Delete
PG
1 hr 48 min Time left
30
030
30
Left Extruder Mode
Before the first printing, please complete the leveling, loading and calibration correctly
under the guidance of the quick start guide.
16
2. Tap the unload switch after corresponding
extruder to unload corresponding extruder.
3. Tap[Begin], the extruder will start heating.
The printer will start unloading filament
after heating completed.
1. Tap[Tools], [Filament] to enter the filament interface.
<
Load Unload
Begin
Left Extruder
Right Extruder
Left Extruder
Right Extruder
<
Cancel
Left Extruder is Heating... Right Extruder is Heating...
69 / 220℃ 69 / 220℃
31% 31%
ToolsPreheatBuild
Setting Status About
Filament Level Home Manual
HOME
<
Please follow steps below if you need to unload filament in
daily use.
Unload Filament
Push filament
down through
for 3 seconds
Press here
Withdraw
Filament
Guidetube
4. Pull filament guide tube out of filament intake,
leave filament 10cm to pull filament easily.
5. Press spring presser and push filament
down through for 3 seconds, then pull out
vertically quickly.
17
1. 剪断包装扎带,撕除缠绕膜。 2. 向上提起外包装箱。
3. 移除顶部泡棉。 4. 移除打印机四周的泡棉。
5. 割开纸箱四角的胶带露出打印机。打开
气泡袋露出打印机。
6. 移除固定顶部的胶带,打开顶盖。
18
10. 移除X轴同步带和Y轴同步带上的卡扣。
7. 取出顶部配件及泡棉。 8. 移除固定打印机前门的胶带。
9. 取出内部的泡沫块,其中包含两个废料盒及两卷3D打印耗材。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Flashforge SZ20-ZN Creator 3 FDM 3D Printer ユーザーガイド

カテゴリー
印刷
タイプ
ユーザーガイド