Sony DSC-WX30 ユーザーマニュアル

4-288-789-11(1)

DSC-WX30

Digital Still Camera / Instruction Manual GB

CT

CS

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call your Sony dealer

regarding this product.

Model No. DSC-WX30

Serial No. ______________________________

Model No. AC-UB10/UB10B

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

IMPORTANT SAFETY INSTRUCTIONS

-SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

English

WARNING

CAUTION

GB

3

GB

• Do not handle damaged or leaking lithium ion batteries.

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ AC Adaptor

Connect the AC Adaptor to the nearest wall outlet (wall socket).

If some trouble occurs while using the AC Adaptor, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

The power cord (mains lead), if supplied, is designed specifically for use with this camera

only, and should not be used with other electrical equipment.

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

For Customers in Europe

GB

4

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

GB

5

GB

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

GB

6

For details on advanced operations, please read “Cyber-shot User Guide”

(HTML) on the CD-ROM (supplied) using a computer.

For Windows users:

1 Click [User Guide] t [Install].

2 Start “User Guide” from the shortcut on the desktop.

For Macintosh users:

1 Select the [User Guide] folder and copy [eng] folder stored in [User Guide]

folder to your computer.

2 After copying is complete, double-click “index.html” in [eng] folder.

• Camera (1)

• Rechargeable battery pack NP-BN (1)

(This rechargeable battery pack cannot be used with Cyber-shot that are

supplied with the NP-BN1 battery pack.)

• Multi-use terminal USB cable (1)

• AC Adaptor AC-UB10/UB10B (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Paint pen (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot User Guide”

• Instruction Manual (this manual) (1)

Refer to “Cyber-shot User Guide” (HTML) on

supplied CD-ROM

Checking the supplied items

Insert the CD-ROM into the CD-ROM drive.

GB

7

GB

A ON/OFF (Power) button

B Shutter button

C W/T (Zoom) lever

D Flash

E (Playback) button

F Power/Charge lamp

G Microphone

H Self-timer lamp/Smile Shutter

lamp/AF illuminator

I Lens

J Screen/Touch panel

K HDMI connector

L Hook for wrist strap

M Speaker

N Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

O Multi connector (Type3b)

P Memory card slot

Q (TransferJet™) mark

R Battery/memory card cover

S Battery insertion slot

T Access lamp

U Battery eject lever

Identifying parts

GB

8

Inserting the battery pack

1

Open the cover.

2

Insert the battery pack.

• While pressing down the battery eject lever, insert the battery pack as

illustrated. Make sure that the battery eject lever locks after insertion.

• Closing the cover with the battery inserted incorrectly may damage the

camera.

Charging the battery pack

Battery eject lever

Power cord

(Mains lead)

For customers in the USA,

Canada

For customers in countries/regions

other than the USA and Canada

Power/Charge lamp

Lit: Charging

Off: Charging finished

Flash: Charging error

GB

9

GB

• When the Power/Charge lamp on the camera does not lit even if the AC Adaptor is

connected to the camera and the wall outlet (wall socket), it indicates that the

charging stops temporarily on standby. Charging stops and enters into standby

mode automatically when the temperature is outside of the recommended

operating temperature. When the temperature gets back within the appropriate

range, the charging resumes. We recommend charging the battery pack in an

ambient temperature of between 10°C to 30°C (50ºF to 86ºF).

• Connect the AC Adaptor (supplied) to the nearest wall outlet (wall socket). If

malfunctions occur while using the AC Adaptor, disconnect the plug from the wall

outlet (wall socket) immediately to disconnect from the power source.

• When charging is finished, disconnect the AC Adaptor from the wall outlet (wall

socket).

• Be sure to use only genuine Sony brand battery packs, multi-use terminal USB

cable (supplied) and AC Adaptor (supplied).

x

Charging time

The charging time is approximately 210 min. using the AC Adaptor

(supplied).

• The above charging time applies when charging a fully depleted battery pack at a

temperature of 25°C (77°F). Charging may take longer depending on conditions of

use and circumstances.

1

Connect the camera to the AC Adaptor (supplied),

using the multi-use terminal USB cable (supplied).

2

Connect the AC Adaptor to the wall outlet (wall socket).

The Power/Charge lamp lights orange, and charging starts.

• Turn off the camera while charging the battery.

• You can charge the battery pack even when it is partially charged.

• When the Power/Charge lamp flashes and charging is not finished,

remove and re-insert the battery pack.

Notes

Note

GB

10

x

Charging by connecting to a computer

The battery pack can be charged by connecting the camera to a computer using

a multi-use terminal USB cable.

• Note the following points when charging via a computer:

– If the camera is connected to a laptop computer that is not connected to a power

source, the laptop battery level decreases. Do not charge for an extended period

of time.

– Do not turn on/off or restart the computer, or wake the computer to resume from

sleep mode when a USB connection has been established between the computer

and the camera. The camera may cause a malfunction. Before turning on/off, or

restarting the computer or waking the computer from sleep mode, disconnect the

camera and the computer.

– No guarantees are made for charging using a custom-built computer or a

modified computer.

x

Battery life and number of images can be recorded

and played back

• The above number of images applies when the battery pack is fully charged. The

number of images may decrease depending on the conditions of use.

• The number of images that can be recorded is for shooting under the following

conditions:

– Using Sony “Memory Stick PRO Duo” (Mark2) media (sold separately)

– The battery pack is used at an ambient temperature of 25°C (77°F).

Note

Battery life Number of images

Shooting (still images) Approx. 115 min. Approx. 230 images

Viewing (still images) Approx. 180 min. Approx. 3600 images

Shooting (movies) Approx. 55 min. —

Notes

GB

11

GB

• The number for “Shooting (still images)” is based on the CIPA standard, and is for

shooting under the following conditions:

(CIPA: Camera & Imaging Products Association)

– [Panel Brightness] is set to [3].

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

• The battery life for movies applies shooting under the following conditions:

– Movie quality: AVC HD HQ

– When continuous shooting ends because of set limits (page 20), touch

(Movie button) again and continue shooting. Shooting functions such as the

zoom do not operate.

x

Supplying power

The camera can be supplied with power from the wall outlet (wall socket) by

connecting to the AC Adaptor, using the multi-use terminal USB cable

(supplied).

You can import images to a computer without worrying about draining the

battery pack by connecting the camera to a computer using the multi-use

terminal USB cable.

• Power cannot be supplied when the battery pack is not inserted in the camera.

• Power supply from the wall outlet (wall socket) is available only when the camera

is in playback mode or when a connection is made between the camera and a

computer. If the camera is in shooting mode or while you are changing the settings

of the camera, power is not supplied even if you make a USB connection using the

multi-use terminal USB cable.

• If you connect the camera and a computer using the multi-use terminal USB cable

while the camera is in playback mode, the display on the camera will change from

the playback screen to the USB connection screen. Press (Playback) button to

switch to the playback screen.

Notes

GB

12

x

Memory cards that can be used

• In this manual, products in A are collectively referred to as “Memory Stick Duo”

media, and products in B are collectively referred to as SD card.

Inserting a memory card (sold separately)

1

Open the cover.

2

Insert the memory card (sold separately).

• With the notched corner facing as illustrated, insert the memory card

until it clicks into place.

3

Close the cover.

Memory card For still images For movies

A

Memory Stick PRO Duo aa (Mark2 only)

Memory Stick PRO-HG Duo aa

Memory Stick Duo a —

B

SD memory card aa (Class 4 or faster)

SDHC memory card aa (Class 4 or faster)

SDXC memory card aa (Class 4 or faster)

Note the notched corner faces

correctly.

GB

13

GB

x

To remove the memory card/battery pack

Memory card: Push the memory card in once to eject the memory card.

Battery pack: Slide the battery eject lever. Be sure not to drop the battery pack.

• Never remove the memory card/battery pack when the access lamp (page 7) is lit.

This may cause damage to data in the memory card/internal memory.

Note

Setting the clock

1

Press the ON/OFF (Power) button.

Date & Time setting is displayed when you turn on the camera for the first

time.

• It may take time for the power to turn on and allow operation.

2

Select a desired language.

3

Select a desired geographic location by following the

on-screen instructions, then touch [Next].

4

Set [Daylight Savings] or [Summer Time], [Date & Time

Format] and [Date & Time], then touch [Next].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

5

Touch [OK].

6

Select the desired display color, following the

instructions on the screen, then touch [OK].

7

When an [In-Camera Guide] introductory message is

appeared on the screen, touch [OK].

ON/OFF (Power)

GB

14

Shooting still images

Shooting movies

• The sound of the lens and lever operating will be recorded when the zoom function

operates while shooting a movie.

• Continuous shooting is possible for approximately 29 minutes at one time at the

camera’s default settings and when the temperature is approximately 25°C (77°F).

When movie recording is finished, you can restart recording by touching

(Movie button) again. Recording may stop to protect the camera depending

on the ambient temperature.

Shooting still images/movies

1

Press the shutter button halfway down to focus.

When the image is in focus, a beep sounds and the z indicator lights.

2

Press the shutter button fully down to shoot an image.

1

Touch (Movie button) to start recording.

• Use the W/T (zoom) lever to change the zoom scale.

2

Touch (Movie button) to stop recording.

Notes

Shutter button

GB

15

GB

x

Selecting next/previous image

Touch (Next)/ (Previous) on the screen.

• To play back movies, touch (Playback) in the center of the screen.

• To zoom in, touch the still image being played back.

x

Deleting an image

Touch (Delete) t [This Image].

x

Returning to shooting images

Touch on the screen.

• You can also return to shooting mode by pressing the shutter button halfway

down.

Viewing images

1

Press the (Playback) button.

• When images on a memory card recorded with other cameras are played

back on this camera, the registration screen for the data file appears.

(Playback)

GB

16

This camera is equipped with built-in instruction guide. This allows you to

search the camera’s functions according to your needs.

In-Camera Guide

1

Touch (In-Camera Guide).

• The mark will appear on the bottom left of the screen while viewing.

2

Select a search method from [In-Camera Guide].

Shoot/ playback guide: Search for various operation functions in

shooting/viewing mode.

Icon guide: Search the function and meaning of displayed icons.

Troubleshooting: Search common problems and their solution.

Objective guide: Search functions according to your needs.

Keyword: Search functions by keywords.

History: View the last 10 items displayed in [In-Camera Guide].

GB

17

GB

Other functions used when shooting or playing back can be operated touching

the MENU on the screen. This camera is equipped with a Function Guide that

allows you to easily select from the functions. While displaying the guide, you

can use various functions.

x

Menu Items

Shooting

Introduction of other functions

Movie shooting

scene

Select movie recording mode.

Easy Mode Shoot still images using minimal functions.

Movie button Shoots movies from all shooting modes quickly.

Flash Sets the flash settings.

Self-Timer Sets the self-timer settings.

Defocus Effect

Set the level of background defocus effect when

shooting in Background Defocus mode.

Still Image

Size(Dual Rec)

Sets the still image size shot while recording a movie.

Still Image Size/

Panorama Image

Size/Movie Size/

Movie Quality

Select the image size and the quality for still images,

panoramic images or movie files.

Cont. Shooting

Settings

Sets the burst shooting settings.

HDR Painting

effect

When [HDR Painting] is selected in Picture Effect, sets

the effect level.

Area of emphasis

When [Miniature] is selected in Picture Effect, sets the

part to focus on.

GB

18

Viewing

Color hue

When [Toy camera] is selected in Picture Effect, sets the

color hue.

Extracted Color

When [Partial Color] is selected in Picture Effect, selects

the color to extract.

EV Adjust the exposure manually.

ISO Adjust the luminous sensitivity.

White Balance Adjust color tones of an image.

Focus Select the focus method.

Metering Mode

Select the metering mode that sets which part of the

subject to measure to determine the exposure.

Scene Recognition Set to automatically detect shooting conditions.

Soft Skin Effect Set the Soft Skin Effect and the effect level.

Smile Shutter

Set to automatically release the shutter when a smile is

detected.

Smile Detection

Sensitivity

Set the Smile Shutter function sensitivity for detecting

smiles.

Face Detection

Select to detect faces and adjust various settings

automatically.

Anti Blink

Set to automatically shoot two images and select image

in which the eyes are not blinking.

Movie SteadyShot Sets the strength of SteadyShot in movie mode.

In-Camera Guide Search the camera’s functions according to your needs.

Easy Mode Increase the text size on the screen for ease of use.

Date Select Selects the desired image to view by date.

Calendar Selects the date to be played back on Calendar.

Image Index Displays multiple images at the same time.

Slideshow Select a method of continuous playback.

Delete Delete an image.

Send by

TransferJet

Transfer data by closely aligning two products equipped

with TransferJet.

GB

19

GB

x

Setting items

If you touch the MENU while shooting or during playback, (Settings) is

provided as a final selection. You can change the default settings on the

(Settings) screen.

* If a memory card is not inserted, (Internal Memory Tool) will be displayed and

only [Format] can be selected.

Paint Paints on a still image and saves it as a new file.

Retouch Retouch an image using various effects.

3D Viewing Set to play back images shot in 3D mode on a 3D TV.

View Mode Select the display format for images.

Display Cont.

Shooting Group

Select to display burst images in groups or display all

images during playback.

Protect Protect the images.

Print (DPOF) Add a print order mark to a still image.

Rotate Rotate a still image to the left or right.

Volume Adjusts the volume.

Exposure data

Sets whether or not to display the shooting data (Exif

data) of the currently displayed file on the screen.

Number of images

in index

Sets the number of images displayed in the index screen.

In-Camera Guide Search the camera’s functions according to your needs.

Shooting Settings

Movie format/AF Illuminator/Grid Line/Clear Image

Zoom/Digital Zoom/Wind Noise Reduct./Scene Recog.

Guide/Red Eye Reduction/Blink Alert/Write Date

Main Settings

Beep/Histogram Setting/Panel Brightness/Language

Setting/Display color/Demo Mode/Initialize/CTRL FOR

HDMI/USB Connect Setting/USB Power Supply/LUN

Setting/Download Music/Empty Music/TransferJet/Eye-

Fi/Power Save/Calibration

Memory Card

Tool

*

Format/Create REC.Folder/Change REC.Folder/Delete

REC.Folder/Copy/File Number

Clock Settings

Area Setting/Date & Time Setting

GB

20

The number of still images and recordable time may vary depending on the

shooting conditions and the memory card.

x

Still images

(Units: Images)

x

Movies

The table below shows the approximate maximum recording times. These are

the total times for all movie files. Continuous shooting is possible for

approximately 29 minutes. The maximum size of an MP4-format movie file is

up to approximately 2 GB.

(h (hour), m (minute))

The number in ( ) is the minimum recordable time.

• The recordable time of movies varies because the camera is equipped with VBR

(Variable Bit Rate), which automatically adjusts image quality depending on the

shooting scene. When you record a fast-moving subject, the image is clearer but

the recordable time is shorter because more memory is required for recording.

The recordable time also varies depending on the shooting conditions, the subject

or the image quality/size settings.

Number of still images and recordable time of

movies

Capacity

Size

Internal memory Memory card

Approx. 19 MB 2 GB

16M 3 335

VGA 98 9600

16:9(12M) 3 355

Capacity

Size

Internal memory Memory card

Approx. 19 MB 2 GB

AVC HD 24M (FX) — 10 m

(10 m)

AVC HD 9M (HQ) — 25 m

(15 m)

MP4 12M — 15 m

MP4 3M — 1 h 10 m

ページが読み込まれています...

Sony DSC-WX30 ユーザーマニュアル

Sony DSC-WX30 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント