Sony SRS-T10PC ユーザーマニュアル

タイプ
ユーザーマニュアル

Sony SRS-T10PCは、コンパクトで持ち運び可能なスピーカーシステムです。USB接続でパソコンに接続するだけで、クリアなサウンドを楽しむことができます。USBケーブルはスピーカー本体に収納できるので、持ち運びにも便利です。

また、音楽CDを再生するための設定も簡単に行うことができます。パソコンのCD-ROMドライブに音楽CDを挿入し、スピーカーとパソコンをUSBケーブルで接続するだけです。パソコンの設定で、CD-ROMドライブのデジタルCDオーディオを有効にする必要があります。

Sony SRS-T10PCは、パソコンで音楽や動画を楽しむのに最適なスピーカーシステムです。コンパクトなサイズで持ち運びにも便利なので、どこでも音楽を楽しむことができます。

Sony SRS-T10PCは、コンパクトで持ち運び可能なスピーカーシステムです。USB接続でパソコンに接続するだけで、クリアなサウンドを楽しむことができます。USBケーブルはスピーカー本体に収納できるので、持ち運びにも便利です。

また、音楽CDを再生するための設定も簡単に行うことができます。パソコンのCD-ROMドライブに音楽CDを挿入し、スピーカーとパソコンをUSBケーブルで接続するだけです。パソコンの設定で、CD-ROMドライブのデジタルCDオーディオを有効にする必要があります。

Sony SRS-T10PCは、パソコンで音楽や動画を楽しむのに最適なスピーカーシステムです。コンパクトなサイズで持ち運びにも便利なので、どこでも音楽を楽しむことができます。

SRS-T10PC [GB/CT] 2-179-931-61(1)
© 2005 Sony Corporation Printed in China
Active Speaker System
SRS-T10PC
2-179-931-61(1)
POWER indicator
23
B
C
To the USB
connecting
terminal of a
computer
1
Image
Cover
1
A
Setting the speaker (see fig. A)
1 Open the cover.
2 Pull out the USB cable from the system
storage section.
3 Stand the speaker on the cover.
Putting the USB cable back in the system
storage section
See illustration.
Preparations
Preparation 1: Connection (see fig. B)
1 Pull out the USB cable from the system
storage section.
2 Connect the USB cable to the USB
connecting terminal of your computer.
Notes on USB connection
•If your computer is connected to other USB devices via a
hub, there may be no sound or malfunction may occur.
Connect the system directly to your computer with the
USB cable to avoid a problem.
•If the USB cable is not properly connected, the system
may not be recognized by your computer. Check the
direction of the USB connecting terminal and connect it
properly.
Preparation 2: Installation of device drivers
(Windows XP)
The device drivers have to be installed, when connecting
to the USB connecting terminal of your computer for the
first time.
The device drivers are included in Windows XP and are
not supplied with the system.
For details, refer to the manual of your computer.
1 Switch on your computer and start
Windows XP.
2 Connect the system to your computer.
3 The “USB Composite Device/USB Audio
Device/USB Human Interface Device”
drivers are automatically installed.
Notes
•You need not perform the above installation procedure
when connecting for the second time or later. (For
different USB connecting terminals, you may have to
install again.)
•During and after installing the device drivers, “C-Media
USB Headphone Set” is displayed in the [USB Audio
Device] properties.
Setting of music CD replay
This setting is necessary when playing back the music CD
in the CD-ROM drive.
1 Select “Control Panel” from the “Start”
menu.
2 Click “Sounds, Speech, and Audio
Devices.”
3 Click “Sounds and Audio Devices” icon
and open “Sounds and Audio Devices
Properties.”
4 Select “Hardware.”
5 Select the CD-ROM icon for replaying the
music from “Devices” and click
“Properties.”
6 Select “Properties.”
7 Click the check box “Enable digital CD
audio for this CD-ROM device.”
8 Select “OK” and exit.
English
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
To prevent fire, do not Cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc. Do not place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area).
Customer Support
The following URLs contain information on the latest
customer support for the speaker, and frequently asked
questions and answers.
Customers in the U.S.A.
http://www.sonystyle.com/support
Customers in Canada
http://www.sony.ca/sonyca/view/english/
support_electronics.shtml
http://fr.sony.ca/sonyca/view/french/
support_electronics.shtml
Customers in Europe
http://www.support-nwwalkman.com/
Customers in Asia Pacific
http://www.css.ap.sony.com/
Microsoft and Windows are registered trademarks
of Microsoft Corporation in the United States and/
or other countries.
In this manual, Microsoft
®
Windows
®
XP Home
Edition and Microsoft
®
Windows
®
XP Professional
are referred to as Windows XP.
•In this manual, Microsoft
®
Windows
®
2000
Professional is referred to as Windows 2000.
In this manual, Microsoft
®
Windows
®
Millennium
Edition is referred to as Windows Me.
In this manual, Microsoft
®
Windows
®
98 Second
Edition is referred to as Windows 98SE.
All other names of systems and products are
trademarks or registered trademarks of their
respective owners. ™ and
®
marks are omitted in this
manual.
Features
Compact design
Compact, portable speaker system to carry along
with your laptop. With a USB connection to your
computer, clear sound is readily available.
This system utilizes the USB bus power; the
connection of the AC power adaptor or batteries are
not necessary. (Note that when your computer is
running on batteries, the life span of the battery is
reduced.)
The USB cable can be stored within the speakers.
Simple settings
Requires a simple USB cable connection only.
Clear sound
Newly developed 39 mm, thin type speaker provides
clear, balanced sound.
Precautions
After operating the system, disconnect the USB cable
from the computer if the system is not to be used for
an extended period.
Do not open the cabinet. Refer servicing to qualified
personnel only.
Do not leave the system in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, moisture, rain or mechanical shock.
Should any solid object or liquid fall into the system,
remove the USB cable and have the system checked
by qualified personnel before operating it any
further.
Do not use alcohol, benzine, or thinner to clean the
cabinet.
Although this system is magnetically shielded, do
not leave recorded tapes, watches, personal credit
cards or floppy disks using magnetic coding in front
of the system for an extended period.
If the TV picture or monitor display is
magnetically distorted
Although this system is magnetically shielded, there
may be cases that the picture on some TV sets/
personal computers sets may become magnetically
distorted. In such a case, turn off the power of the TV
set/personal computer set once, and after 15 to 30
minutes turn it on again. For the personal computer
set, take the appropriate measures such as data
storage before turning it off.
When there seems to be no improvement
Locate the system farther away from the TV set/
personal computer set. Furthermore, be sure not to
place objects in which magnets are attached or used
near the TV set/personal computer set, such as audio
racks, TV stands, toys etc. These may cause magnetic
distortion to the picture.
If you have any questions or problems concerning your
system that are not covered in this manual, please
consult your nearest Sony dealer.
Preparation 2: Installation of device drivers
(Windows 2000)
The device drivers have to be installed, when connecting
to the USB connecting terminal for the first time.
The device drivers are included in Windows 2000 and are
not supplied with the system.
For details, refer to the manual of your computer.
1 Switch on your computer and start
Windows 2000.
2 Connect the system to your computer.
3 The “USB Composite Device/USB Human
Interface Device/USB Audio Device”
drivers are automatically installed.
Notes
•You need not perform the above installation procedure
when connecting for the second time or later. (For
different USB connecting terminals, you may have to
install again.)
•During and after installing the device drivers, “C-Media
USB Headphone Set” is displayed in the [USB Audio
Device] properties.
Setting of music CD replay
This setting is necessary when playing back the music CD
in the CD-ROM drive.
1 Select “Settings” – “Control Panel” from
the “Start” menu.
2 Double click the icon “Sounds and
Multimedia” and open “Sounds and
Multimedia Properties.”
3 Select “Hardware.”
4 Select the CD-ROM icon for replaying the
music from “Devices” and open
“Properties.”
5 Select “Properties.”
6 Click the check box “Enable digital CD
audio for this CD-ROM device.”
7 Select “OK” and exit.
Preparation 2: Installation of device drivers
(Windows Me)
The device drivers have to be installed, when connecting
to the USB connecting terminal for the first time.
The device drivers are included in Windows Me and are
not supplied with the system.
For details, refer to the manual of your computer.
1 Switch on your computer and start
Windows Me.
2 Connect the system to your computer.
3 Install the “USB Composite Device”
driver.
The “USB Composite Device” driver is
automatically installed.
4 Install the “USB Audio Device” driver.
1 [Add New Hardware Wizard] is displayed just
after the “USB Composite Device” driver is
installed.
2 Check that “USB Audio Device” is displayed in
[Windows has found the following new
hardware] window, and check that the
“Automatic search for a better
driver[Recommended]” check box is selected
and click “Next.”
3 The “USB Audio Device” driver is automatically
installed.
4 When [Windows has finished installing the
new hardware device] is displayed, click
“Finish.”
5 Install the “USB Human Interface Device”
driver.
The “USB Human Interface Device” driver is
automatically installed after “USB Audio Device
driver is installed.
6 Restart your computer with the system
connected.
Note
You need not perform the above installation procedure
when connecting for the second time or later. (For
different USB connecting terminals, you may have to
install again.)
Settings of music CD replay
This setting is necessary when playing back a music CD in
the CD-ROM drive.
1 Select “Settings” – “Control Panel” from
the “Start” menu.
2 Double click the “System” icon and open
“System Properties.”
3 Select “Device Manager.”
4 Double click the “CD-ROM” icon.
5 Select the drive for replaying music, and
click “Properties.”
6 Select “Properties.”
7 Click the check box “Enable digital CD
audio for this CD-ROM device.”
8 Select “OK” and exit.
Preparation 2: Installation of device drivers
(Windows 98SE)
The device drivers have to be installed, when connecting
to the USB connecting terminal for the first time.
The device drivers are included in Windows 98SE and are
not supplied with the system.
Furthermore, you will need the Windows 98SE CD-ROM
to install the device drivers.
For details, refer to the manual of your computer.
1 Switch on your computer and start
Windows 98SE.
2 Connect the system to your computer.
When the system is connected to the computer, [Add
New Hardware Wizard] is displayed and the
installation of the device driver automatically starts.
Install each driver following the on-screen
instructions.
* When a message such as Insert the disk labeled
Windows 98SE CD-ROM is displayed, insert the
Windows 98SE CD-ROM in the CD-ROM drive and
click “OK.”
Depending on the kind of computer you are using,
you may have to specify the drive names (such as
D:) or file names.
3 Install the “USB Composite Device”
driver.
1 Check that “USB Composite Device” is displayed
in the [This wizard searches for new drivers
for] window, and click “Next.”
[What do you want Windows to do?] is
displayed.
2 Check that the “Search for the best driver for
your device.[Recommended].” check box is
selected and click “Next.”
[Windows will search for new drivers in its
driver database on your hard drive, and in any
of the following selected locations.] is
displayed.
3 For items checked at the beginning, check the
“CD-ROM drive” check box and click “Next.”
[Windows driver file search for the device] is
displayed.
4 Check that [USB Composite Device] is displayed
and click “Next.”
The driver is copied.
5 When [Windows has finished installing the
software that your new hardware device
requires.] is displayed, click “Finish.”
4 Install the “USB Human Interface Device”
driver.
1 Check that “USB Human Interface Device” is
displayed in the [This wizard searches for new
drivers for] window, and click “Next.”
[What do you want Windows to do?] is
displayed.
2 Check that the “Search for the best driver for
your device.[Recommended].” check box is
checked, and click “Next.”
[Windows will search for new drivers in its
driver database on your hard drive, and in any
of the following selected locations.] is
displayed.
3 For items checked at the beginning, check the
“CD-ROM drive” check box, and click “Next.”
[Windows driver file search for the device] is
displayed.
4 Check that [USB Human Interface Device] is
displayed, and click “Next.”
The driver is copied.
5 When [Windows has finished installing the
software that your new hardware device
requires.] is displayed, click “Finish.”
5 Install the “USB Audio Device” driver.
1 Check that “USB Audio Device” is displayed in
the [This wizard searches for new drivers for]
window, and click “Next.”
[What do you want Windows to do?] is
displayed.
2 Check that the “Search for the best driver for
your device.[Recommended].” check box is
selected and click “Next.”
[Windows will search for new drivers in its
driver database on your hard drive, and in any
of the following selected locations.] is
displayed.
3 For items checked at the beginning, check the
“CD-ROM drive” check box and click “Next.”
[Windows driver file search for the device] is
displayed.
4 Check that [USB Audio Device] is displayed, and
click “Next.”
The driver is copied.
5 When [Windows has finished installing the
software that your new hardware device
requires.] is displayed, click “Finish.”
6 Restart your computer with the system
connected.
Note
You need not perform the above installation procedure
when connecting for the second time or later. (For
different USB connecting terminals, you may have to
install again.)
Setting of music CD replay
This setting is necessary when playing back the music CD
in the CD-ROM drive.
1 Select “Settings” – “Control Panel” from
the “Start” menu.
2 Double click the icon “Multimedia” and
open “Multimedia Properties.”
3 Select “CD Music.”
4 Click the check box “Enable digital CD
audio for this CD-ROM device.”
5 Select “OK” and exit.
How to use (see fig. C)
Before starting, refer to “Setting the speaker.”
1 Switch on the computer.
The POWER indicator lights up.
Note
When connecting the system to your computer, the
volume of your computer may increase to the
maximum level. Turn down the volume of your
computer before playing the music software.
2 Start the software for replaying the
music in your computer.
Note
If the system is connected while the music software
is running in your computer, music may not come
from the system. Stop the music software once and
start again. Music can be heard from the system.
To adjust the volume
To set the appropriate volume, adjust the volume control
of your computer.
If the cover is detached
1 Insert one side of the hook of the cover
in the rear hole.
2 Insert the other side of the hook in the
rear hole.
Notes on use
•If the volume is too low, the volume of the computer
may be set at a low level. Check the computer’s volume
from the control panel. The volume may differ,
depending on the software’s recording levels.
If you can only hear music from the system with the
computer running on batteries, battery charge has
dropped. Use the AC adaptor when using the system
for an extended period.
Do not continuously cause the “Beep” to sound in your
system, to avoid reducing battery life span or
malfunction from excess current.
Do not use the system via a USB hub or USB extension
cable as a malfunction may occur. Connect the system
directly to the USB connecting terminal of your
computer.
When connecting the system to the USB connecting
terminal of your computer, do not pull out or insert the
plug repeatedly or forcibly as the system may not be
recognized by computer, there may be no sound from
the system, or the system may malfunction.
Connect the system to the USB connecting terminal of
your computer. For details, refer to the manual of your
computer.
•When checking the connection between the system and
the computer, check the device manager of the
computer. For details, refer to the manual of your
computer.
When the computer has two or more USB connecting
terminals, the system may not be used with other USB
devices at the same time as low-output, sound skipping
or noise may occur. For details, refer to the manual of
your computer.
Operations are not guaranteed with Windows OS
installed in do-it-yourself computers, upgraded
Windows OS, and non-compliant OS.
Sony recommends a Pentium II CPU speed of 300 MHz
or faster, or Celeron speed of 500 MHz or faster. If the
requirements of the CPU is insufficient, or when other
applications are running simultaneously, reading data
may skip and cause noise or intermittent sound.
If the sound from the speakers is distorted, or noise is
excessive, adjust the volume of the computer through
the control panel.
If the sound from the alarm of your computer and that
of playback is unbalanced, adjust by following the
manual of your computer.
Sony recommends that you take a back up of important
data before installing the USB device drivers. Sony will
not be responsible in the case that the computer cannot
be used or data is lost due to a mistaken operation or
breakdown.
When using the suspension resume function (system
suspend, system hibernation, etc.), the system speakers
may not work correctly. In such a case, restart either the
application or the computer.
Do not disconnect and reconnect the USB cable while
playing music in a CD player or in a media player. It
may cause a malfunction or a breakdown.
Do not disconnect and reconnect the USB cable of the
system while running music playback software as a
malfunction may occur. If, however, you have
disconnected and connected the USB cable, restart it
after shutting down any currently running software.
If the USB plug is inclined or is connected slowly
between the system to the USB connecting terminal,
malfunction may occur. Connect the plug squarely and
promptly. If your computer malfunctions, reconnect the
system to your computer or restart your computer.
If you start the music playback software soon after the
system is connected to your computer, malfunction may
occur. Start the software 5 seconds after the system is
connected.
When playing a music CD, be sure to click the check
box “Enable digital CD audio for this CD-ROM
device.” If not, the music CD may not be played. For
details on how to click the check box, refer to the
manual of your computer.
•While using the system with Windows 2000, the volume
of your computer may be increased when resuming
from stand-by mode. In such a case, adjust the volume
of your computer.
Troubleshooting
Sound is distorted.
The input signal is too high.
c Reduce the volume of the computer.
c Depending on the software you are using, the plot
comes closer to being flat by adjusting the equalizer.
Sound is low.
The volume control of the computer or the volume of the
music playback software must be turned down.
c Adjust the volume control of your computer.
There is no sound.
The USB cable is not connected properly.
c Connect the USB cable properly.
The system is connected while music software is being
replayed.
c Stop playback of the music software and start again.
The audio replaying device of your computer is not set
correctly.
c Windows XP : Select “Audio,” in [Sounds and Audio
Devices Properties], and select “C-Media USB
Headphone Set” for [Default device] in the Sound
Playback menu.
c Windows 2000 : Select “Audio” in [Sounds and
Multimedia Properties], and select “USB Audio
Device” for [Preferred device] in the Sound Playback
menu.
c Windows Me : Select “Audio” in [Sounds and
Multimedia Properties], and select “USB Audio
Device” for [Preferred device] in the Sound Playback
menu.
c Windows 98SE : Select “Audio” in [Multimedia
Properties], and select “USB Audio Device” for
[Preferred device] in the Playback menu.
The volume control of the computer or the music
playback software is set at “Mute.”
c Remove the mute.
The USB port is not recognized.
c Restart after quitting the playback software. If the
problem persists, restart your computer.
USB is not available.
c Check the device manager of your computer.
There is noise or no sound.
•The CPU of your computer is overloaded.
c Exit other applications.
The system is being used via the USB hub.
c Connect the system directly to the USB connecting
terminal of your computer.
There is no sound from the speakers when
using the built-in mic or external mic of the
connected computer.
The audio recording device of your computer is not set
correctly.
c Change the audio recording device of your computer,
from “USB Audio Device” to the audio device or
external mic installed in your computer.
For details on the operation of your computer, refer to the
manual of your computer.
There can be some breakdowns that cannot be solved
even with “Troubleshooting.” In such cases, contact your
nearest Sony dealer.
Specifications
Speaker section
Enclosure type Full range, Bass reflex,
magnetically shielded
Speaker system 39 mm
Impedance 4
Rated input power 0.25 W
Maximum input power 0.3 W
Amplifier section
Maximum output power 0.25 W + 0.25 W
(10 % T.H.D., 1 kHz, 4 )
Input USB cable, Type A plug,
Approx. 30 cm (11
7
/8 inch)
System required
Compliant computer IBM PC/AT or compatible
computers with USB port
Compliant OS* Windows XP Professional,
Windows XP Home Edition,
Windows 2000 Professional,
Windows Millennium Edition,
Windows 98 Second Edition
Recommended CPU Pentium II 300 MHz or faster/
Celeron 500 MHz or faster
General
Power supply USB bus power compliant
(5 V, 500 mA or less)
Dimensions (w × h × d) Approx. 170 × 60 × 24 mm
(6
3
/4 × 2
3
/8 ×
31
/32 inch)
Mass Approx. 190 g (7 oz.)
Supplied accessory Operating instructions (1)
Design and specifications are subject to change without
notice.
* Complies with the original manufacturer-installed
operating system. Trouble-free operations are not
guaranteed for all computers with the above systems
installed.
Operating Instructions
SRS-T10PC [GB/CT] 2-179-931-61(1)
23
B
C
1
1
A
A
1
2
3
B
1
2
1
2
3
[ ]
1
2
3
4
5
6
7
8
http://www.sonystyle.com/support
http://www.sony.ca/sonyca/view/english/
support_electronics.shtml
http://fr.sony.ca/sonyca/view/french/
support_electronics.shtml
http://www.support-nwwalkman.com/
http://www.css.ap.sony.com/
® ®
® ®
® ®
® ®
® ®
®
1
2
3
[ ]
1
2
3
4
5
6
7
1
2
3
4
1
[ ]
2 [ ]
3
4 [ ]
5
6
1
2
3
4
5
6
7
8
1
2
[ ]
3
1 [
]
[ ]
2
[
]
3
[ ]
4 [ ]
5 [
]
4
1
[ ]
2
[
]
3
[ ]
4 [ ]
5 [
]
5
1 [ ]
[ ]
2
[
]
3
[ ]
4 [ ]
5 [
]
6
1
2
3
4
5
C
1
2
1
2
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
  • Page 1 1
  • Page 2 2

Sony SRS-T10PC ユーザーマニュアル

タイプ
ユーザーマニュアル

Sony SRS-T10PCは、コンパクトで持ち運び可能なスピーカーシステムです。USB接続でパソコンに接続するだけで、クリアなサウンドを楽しむことができます。USBケーブルはスピーカー本体に収納できるので、持ち運びにも便利です。

また、音楽CDを再生するための設定も簡単に行うことができます。パソコンのCD-ROMドライブに音楽CDを挿入し、スピーカーとパソコンをUSBケーブルで接続するだけです。パソコンの設定で、CD-ROMドライブのデジタルCDオーディオを有効にする必要があります。

Sony SRS-T10PCは、パソコンで音楽や動画を楽しむのに最適なスピーカーシステムです。コンパクトなサイズで持ち運びにも便利なので、どこでも音楽を楽しむことができます。

他の言語で