Chinavision CVMV-I180 ユーザーマニュアル

カテゴリー
時計
タイプ
ユーザーマニュアル
USER MANUAL
WATCH DVR (1080P & IR NIGHT VISION)
-1-
一、 总览
图片仅供参考,请以实物为准
A、开关键 B、状态指示灯 C、红外/模式键 D、时间把的
E
USB 接口 F红外感应灯 G录音孔 H、摄像头
重要声明:
本产品是世界首款带高清红外摄像功能高科技手表,并具备一定防水功。在
设计与制造方面,按照 3 度防水标准(防水 30 米)的相关工艺,但由于本产品的
特殊结构这并不代表您能将本产品作为一款潜水表,用于水下摄录更不能保
本产品在水压下保持不渗水和正常工作,本产品所有的防水设计只是为了避免日常
生活中,少量的飞溅液体或者沙石进入产品机壳内部而损坏产品因此,您不能将
其置于水下工作,并且需要严格按照说明书的指导来使用产品,如果因为您使用不
当而造成产品进水损坏,本公司将不再对此产品提供质保以及售后服务。
要本产品更具保障的发挥其防水能力,您需要严格的遵守以下操作方法:
-2-
区分 USB 密封旋钮、麦克风透音旋钮,麦克风密封旋钮这 3 种旋钮。
请根据上图区分麦克风旋钮与 USB 旋钮的差别,不能交换使用,否则起不到
任何的防水防尘效果,而导致产品损坏。
AMIC1 B-MIC2 都是麦克风拾音孔的旋钮,高度一致。但一个有中间有孔,
一个中间没有孔。有孔的是麦克风录音孔的旋钮。没有孔的是 USB 孔盖及麦克
风防水盖。请注意区分。
AMIC1 为带有透声孔的金属旋钮,在该旋钮中心部位有一个孔位(见下图)
用于声音传导,在良好的使用环境下,建议使用该旋钮,使得录制视频的同时也
能够同步录入声音。
BMIC2 不带透声孔的麦克风密封旋钮,在该旋钮内部,有一个防水密封胶
垫,用于密封麦克风孔,在恶劣的使用环境下,建议使用该旋钮,起到麦克风
的防水作用。使用该旋钮后,能够防止飞溅的液体与粉尘进入麦克风孔位,但
同时也隔阻了外部声音进入麦克风,所以,当麦克风孔位旋上了该旋钮,录制
的视频将不带同步的声音。
各个防水旋钮在使用时,请务必旋紧。
意:检查 USB 密封旋钮以及麦克风密封旋钮的密封胶垫是否脱落,如果
脱落,请不要将其作为防水旋钮使用,立即换用备用的防水旋钮。
-3-
二、 产品简介
本产品是世界首款带红外夜视功能的高清摄像手表,数码摄像、拍照、录音功
能的摄像手表,具有操作简便,小巧精致,美观实用,便于携带的特点,是商务
教育、安防、媒体、司法、旅游、医疗、生活等领域的实用工具,深受广大用户
睐。
部件说明
1.1 示灯说明:图示 B 是状态指示灯,其中蓝灯为录像模式的状态指示灯;红灯
是拍照模式的状态指示灯;红灯和蓝灯同时点亮单独录音模式指示灯。
1.2
钮说明:开关键(图示 A)用于开机、关机、摄像、暂停。模式键(图示 C
用于在录像模式、拍照模式、单独录音及红外功能开启.
1.3
座说明:USB 插座(图示 E,用于连接电脑或者充电器,是进行数据传输、
充电和外接电源供电的接口.
1.4
克风和摄像头:麦克风(图示 G用来拾取声音信号;高清摄像头(图示 H
用来拾取影像信号。
1.5
间调校手柄:时间调校手柄(图示 D)用于调整手表的时间。
三、 操作说明
使用前须知:
建议:连接电脑时,请先将数据线与手表连接,再连接电脑!
本品内部为精密电子元器件组成,操作时轻触即可请勿大力操作以免损坏按键,
如果读不到盘,请将 USB 线稍微向外拔出一点红蓝灯亮即可连接电脑。
本机特设了组合键复位功能,如出现死机情况请同时按住 A C 键即可使
器复位。
使用 PC CAMERA(视频摄像头)功能时,请先安装随机配带的驱动程序。
1
录像操作:长按 A 键约 2 秒,红蓝双灯亮后蓝灯闪烁直接进入摄像状态。短按
一次 C 键,蓝灯闪烁,表示正在录像,录像中连续短按二次 A 键,停止录像进
入待机状态并自动保存,再次短按,重新开始录像。
2
外灯启动/关闭:当机器进入正常摄像状态时,长按 C 键,红灯闪烁 3 次,
此时机器已经进去红外摄像状态。此时短按 C 键一次,蓝灯闪烁三下。红外灯关
闭进入正常摄像状态。
3
照操作:当机器进入摄像状态时,短按 A 键二次,蓝灯常亮进入待机状态,
此时短按 C 键,选择指示灯为红色时,短按 A 1 次红灯闪烁一次,表示拍照
一张并成功保存。
4
独录音:当机器进入摄像状态时,短按 A 键二次,蓝灯常亮进入待机状态,
此时短按 C 键,选择指示灯为红蓝状态时,短按 A 1 次,红蓝灯闪烁开始交
替闪烁,表示此时已经进入单独录音状态。
-4-
注:摄像机内置高容量聚合物锂电池,无记忆效应,随用随充,但最初使用的
前五次,请将电池用完后再充电至饱和,以启动电池最大容量,获取标准工作时
间。
5U
与网络摄像头:在本机关机状态通过 USB 线与电脑良好连接,在我的电脑
中出现“可移动硬盘盘符,本机作为 U 盘使用在本机开机状态通过 USB 线
与电脑良好连接,则我的电脑会出现 Standard Camera,本机作为网络摄像头使
用。
根据电脑配置或者系统差异,电脑不一定一次就能检测到摄像头功能,如果
偶然出现电脑无法进入摄像头功能而进入了可移动磁盘请移除摄像机,并在摄
像机开机后重新连接电脑;如果你是第一次在你电脑上使用摄像机的电脑摄像头
功能,请安装随机光盘里面或者经销商提供的摄像头驱动程序;为了避免设备受
到损坏,当你准备连接设备到电脑上时,请先将随机附带的数据线连接到摄像机
上,再将数据线另外一端连接到电脑上。
6
置录像时间: 摄像机提供了在视频文件中显示录像时间的功能,格式为:
-- 时:分:秒,设置时间方法如下:
在本机关机状态通过 USB 线与电脑良好连接,我的电脑中出现“可移动硬盘
盘符。打开 Windows 软件附件中的写字板或记事本*.txt 格式)入:2012.01.24
13:30:30 Y
取文件名:time.txt
将该文件保存在可移动硬盘的根目录下,切 USB 线连接,再开机录像,录像
和拍照右下角的时间就是新修改的时间和日期了。
7
动磁盘 在关机状态或者待机状态时,可以连接电脑,此时,电脑将会弹
出可移动磁盘标识,影像文件保存目录为:*\ _DCIM\100DSCIM;需要卸载
摄像机时,请点击任务栏右下角的可移动设备理图标,在里面卸载该可移动存
储设备,待系统确认可以安全拔出硬件后,再断开摄像机与电脑的连接。
注意意:根据电脑配置或者系统差异,识别可移动磁盘的时间会稍有不同,请耐心
等待,此期间最好不要进行摄像机的操作,以免对电脑识别硬件造成影响。如果
长时间未识别到可移动磁盘,请尝试重新插入如果仍旧无法识别该硬件,请确
认你的操作系统、主板驱动程序、usb 接口、连接线是否都正常;请按照规范的
流程卸载硬件,以免对电脑或者摄像机造成损害。为了避免设备受到损坏,当你
准备连接设备到电脑上时,请先将随机附带的数据线连接到摄像机上,再将数据
线另外一端连接到电脑上。
8异常处理
摄像机存储空间不足时,将在蓝灯和红灯同时闪烁约 5 秒后,自动保存当前影像
文件并关机。如果你要继续使用摄像机,请在电脑上备份所需影像文件,并删除
存储器内的旧文件,以腾出足够存储空间;
摄像机电池余量不足时,将在蓝灯和红灯交替闪烁约 5 秒后,自动保存当前影像
文件并关机。如果你要继续使用摄像机,请先充电;
摄像机因偶然的不当操作或其他特殊原因停止响应时可同时按下模式键和开关
键,进行复位
-5-
-1-
1,Profile
Picture is only for reference
AON/OFF BIndicator CIR/Mode Button DTime Reset
E
USB FIR Lamp GMic HLens
Button Introduction
1) A Button
It is for turn on/turn off the camera,record video,pause
2) B Button Indicator
B Button is MODE Indicator.Blue is for Video Mode
Red is for Photo Mode
Red light and Blue light are burning at the same time,it is for sound
record Mode.
3) C Button
It is Mode Button,for switching between recording video,shooting photo,sound
record and IR Night vision function.
4) D Time Reset
It is for resetting the time of watch.
5) E USB
It is for connecting the watch and PC or charger.
6) F IR Lamp
It is the working status of IR
7)G MIC
It is for recording the Audio
8)H Lens
It is the lens to record video
Notice:
-2-
It is the first FULL HD IR Night Vision Watch Camera with waterproof in
the world.
We design this Waterproof Watch,we used some waterproof standard for
waterproof 30 meters workarts.But because of the special construction of
this IR watch,this watch can not use underwater 30 meters. Normaly,you can
use it underwater within 3 meters.
This manual introduce how to operate correctly.Please be sure you
understand it completely before using.
1,Special Parts Construction and Introduction
The nut,AMIC1 and the nut,B:MIC2 are microphone hole nut,the height
of them are same.
The nut A,MIC1 is with a hole in the center of the nut(the following
picture),it is for transmite the sound.If the environment permit,please use
this nut.When you take the video,the equipment also can record the
sound.
The nut,BMIC2 is without the hole,but it is with a rubber fitting inside
which can anti-water,When it is in the humidity or dust
environment,please use this nut.But when you use this nut,the equipment
can not record the sound.
Please tighten the nuts when you use the equipment.
Before use the nut,please check if the rubber is inside of the nut.If
not,please change the new one.
Picture1
THE NUT STRUCTURE SHOWED AS FOLLOWING PICTURE:
Picture2
-3-
2,Introduction of Product
This product is the first FULL HD IR Night Vision watch camera with shooting
photo,recording video,sound recording,IR night vision functions.And,this baby is
so practical,just for the users from business,education,editor etc.
3,Operation
1,Connect Camera and PC
Connect USB Cable and Watch
Connect USB Cable and Computure
Notice:
If the Computure can not recognize the movable disc,please input the USB cable
again.If the red light and blue light on watch are burning,it must connect well.
2
Video
Press A Button for about 2 seconds and release it.
The red indicator and the blue indicator are burning for about 2 seconds.
The red indicator is off.The blue indicator is burning.
Press and release the button,C.
The blue indicator is flashing during recording video.
Press and release the button A for two times continuously to stop recording
to standby status.
Press and release A button again to start recording.
3 IR Indicator
a) Start IR Indicator
In the status of Video,press the button,C for about 4 seconds,the red light
flashes three time
b) Stop IR Indicator
Press and release button,C,the blue light will flahs three times.The red light
will be off.
4 Shooting an image
Turn On camera
Press and release the button,A two times
The blue light is burning.
The red indicator is off
Press and release the button,C
The red indicator is burning
Press and release the button,A
The red indicator flashes one time.
5 Sound Record
Turn on Camera
Press and release the button A two times
The blue light is burning
6 Sound Record
Turn On the camera
Press and release the button,A for two times
Blue indicator is burning
Press and release the button,C
-4-
The blue indicator is burning
Press the button,A
The blue indicator and red indicator flashes alternately
7
Movable disc
a) Turn Off Camera
b) Connect camera and computure with original USB Cable
c) The movable disc sign will show on screen of computure
Web Camera
Turn on Camera
Connect camera and computure with original USB Cable
The Standard Camera sign will show on screen of computer
Notice:
If the computer can not recognize the camera, please try again.
8, Time Reset
Handle Reset
Turn off Camera
Connect Camera and computer with original USB Cable
The Movable Disc will be shown on computer
Open the Movable Disc
Creat a file, *.txt
Input 2012.01.24 13:30:30 Y
Save the file as time.txt
Disconnect the camera and computer
Auto Reset
Turn off Camera
Connect Camera and computer with original USB Cable
The Movable Disc will be shown on computer
Open the Movable Disc
Click the file WriteTime.exe in the folder of Movable Disc two times
Click Update
FAQ
a) The watch camera is off after the red light and blue light are flashing for 5
seconds.
Answer: It is because of there is no enough memory, before the camera is
off, it will save the file auto-metical.
b) The watch camera is off after the red light and blue light are flashing
alternately for 5 seconds.
Answer: No Power
c) What should I do when the camera stuck because of the wrong operation or
-5-
any other unknown reasons?
Answer: Please press the Mode Button and On/Off Button together to
reset the camera.
Specification
Items Parameters
Video Form AVI
Video Code M-JPEG
Video Resolution 1920*1080
Software Operation system or major audio and video playback
software
Image JPG
System Windows me/2000/xp/2003/vistaMac os 10.4Linux
Voltage DC-5V
Data Transfer
Interface
Mini 4 Pin USB
Memory TF
Battery Li-ion Battery
Notice
Work place: It is only for legal place.
Battery: You need to charge it after it does not work for long time.
File safty:It is not the professional memory card, so it can not instead
of professional memory card completely. you need to keep back-up.
Video quality: It is not the professional video equipment, so it can not
instead of professional Video Equipment completely.
Working temperature: 0—40°C,it is better to use in the room
tempreture.It is because of the IR Function if you find the
tempreture is rising when you use IR function. The battery working
time will drop down at this condition.
Working humidity: 20%-80%, it is with waterproof function. Before you
enter into the waterproof status, do not put it into water or humid
place.
Illuminance: Please to use it in the luminous place.
Cleanliness:it is better not to use it in the dust place.
Other iterms:It can not use in the high magnetic fields , uniform
electric field.It can not be striked,quick hardly.
Notice:Please contact the local selleres if you need any other more
inforamtion or help.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chinavision CVMV-I180 ユーザーマニュアル

カテゴリー
時計
タイプ
ユーザーマニュアル

他の言語で