Dell S520 Projector クイックスタートガイド

Dell™ | Interactive Projector

S520

Laser Touch Setup Guide

レーザータッチセットアップガイド

激光触控设置指南

雷射觸控設定指南

레이저 터치 설치 설명서

Panduan Konfigurasi Sentuhan Laser

คูมือการติดตั้ง Laser Touch

S520 Laser Touch QSC_A02-APCC.book Page 1 Thursday, May 8, 2014 4:54 PM

S520 Laser Touch QSC_A02-APCC.book Page 2 Thursday, May 8, 2014 4:54 PM

Dell™ | Interactive Projector

S520

Laser Touch Setup Guide

S520 Laser Touch QSC_A02-APCC.book Page 1 Thursday, May 8, 2014 4:54 PM

About Notes

NOTE: A NOTE indicates important information that helps you make better use of your

projector.

______________ ____

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of

Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Microsoft,

Windows 7, and Windows Vista are trademarks or registered trademarks of Microsoft Corporation

in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in

trademarks and trade names other than its own.

June 2014 P/N 05PF0 Rev. A02

S520 Laser Touch QSC_A02-APCC.book Page 2 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

3

NOTE: You computer must have the

following minimum system requirements:

Operating System:

• Windows XP Professional service pack 3

32-bit, Windows 7 32-bit/64-bit, and

Windows 8 32-bit/64-bit

• Windows .NET Framework 4.0

installation is required (You can

download it from the Microsoft site)

• MacOS 10.6 and above

Minimum Hardware:

• Windows processor type: Intel Core i3

or above

• MAC processor type: Intel Core i2 duo

or above

• Windows/MAC RAM: 2 GB of RAM

required or more are recommended

• Windows/MAC Min. HDD space: 110 MB

of available hard-disk space

Part A: Install the Whiteboard

1 Install the whiteboard.

NOTE: Refer to "whiteboard installation

instructions".

Set Up Laser Touch on Your Projector

S520 Laser Touch QSC_A02-APCC.book Page 3 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

4

Part B: Mount the Projector

2 Install the wall mount and the projector.

NOTE: The wall mount is shipped with your

projector. Please refer "wall mount

installation instructions".

NOTE: Project at 87" for a maximum image

size projection or ~84" if you would like to

leave a border around the projector image

for optimal touch experience.

Part C: Attach Laser Curtain Kit

3 Attach the laser curtain kit onto the

whiteboard.

NOTES:

a Attachment is aided with locating pin

and magnets.

b You can also lock the kit in place with a

security screw.

c There is a cover for the laser curtain kit.

(b) Screw

(a)

S520 Laser Touch QSC_A02-APCC.book Page 4 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

5

Part D: Connect Necessary

Cables

4 Connect power, video, Mini USB, and DC-

to-DC cables to the projector.

5 Connect the power cable to the power

outlet.

6 Connect the DC-to-DC cable to the laser

curtain kit.

2m DC-to-DC cable

S520 Laser Touch QSC_A02-APCC.book Page 5 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

6

7 Connect the VGA cable to your computer.

NOTE: You can also project the image

through VGA-B and HDMI. Press the left

button on your control panel for auto

searching and selecting the correct input

source.

8 Connect the Mini USB cable to your

computer.

9 Power on the projector by pressing the

power button on the remote control.

MOLEX

5 m Mini USB cable

S520 Laser Touch QSC_A02-APCC.book Page 6 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

7

Part E: Install the Touch Driver

on Your Computer

10 The TouchDriver install message will pop-

up automatically after you plug in the USB

cable to your computer. Follow the on-

screen instruction to complete setup.

The driver icon will appear in your

computer's notification area if the driver has

installed successfully.

If the Touch driver is not automatically installed,

go to My Computer and run "TouchDriver.exe".

NOTE: You may require administrator-level

access to install the driver. Contact your

network administrator for support.

Part F: Initialize the Touch

Control Function: Auto Adjust

Touch

This is recommended for first-time use, and

necessary when touch screen responds

inaccurately or erratically.

NOTE: You have to project in duplicate or

projector only modes.

11 When executing driver, click the icon.

The following menu appears on-screen.

S520 Laser Touch QSC_A02-APCC.book Page 7 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

8

Select "Auto adjust touch for this computer"

option to execute the auto "calibration and

touch area" procedure.

If the "auto adjust touch failed" message

prompts, please take the steps below for

troubleshooting, then do auto adjust touch

again.

a Turn lights off or reduce stray light to

whiteboard

b Do not walk in front of or move the

projector

c Adjust focus to sharpen the projected

image

If the "auto adjust touch still failed" message

appears on screen, please change to manual

calibrate touch and manual touch area.

Calibrate Touch by Manual:

Executing driver, click the icon, and go

to Advanced Settings menu, click the

Calibrate touch option to execute the

manual calibrate touch mode.

Touch the target marks on the screen.

(Press the "ESC" key to exit the calibration

process). After the 4

th

point of calibration

is finished, please wait for 2 seconds while

the calibration data is saved.

1

3

4

2

S520 Laser Touch QSC_A02-APCC.book Page 8 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

9

Touch Area by Manual:

Executing driver, click the icon, and go

to Advanced Settings menu, click the Set

touch area option to execute the manual

calibrate touch mode.

Touch area window will pop up.

Drag the 4 points, in the order of P1 to P4.

The green frame should lie slightly outside

the projected image area and there should

not be any reflected light spot within this

frame. Once you have completed this task,

click "Exit".

S520 Laser Touch QSC_A02-APCC.book Page 9 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

10

Part G: Touch Sensitivity

Adjust

When laser curtain has been operative for a

long period of time, the sensitivity might be

slightly reduced. Touch sensitivity functions to

re-sensitize the laser curtain by restoring the

initial setting.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Set touch

Sensitivity option to re-sensitize laser curtain

by restoring the initial setting.

Default value for Touch Sensitivity is 4.

Increasing the value increases the Touch

Sensitivity and Decreasing the Touch Sensitivity

values reduces it.

S520 Laser Touch QSC_A02-APCC.book Page 10 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

11

Part H: Reset All Touch

Settings

When auto or manual "calibrate touch and

touch area" settings still are incorrect, you can

to execute the Reset all touch settings option

to reset all settings to its factory default.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Reset all

touch settings option to re-sensitize laser

curtain by restoring the initial setting.

Part I: Touch Sensor Adjust

When your touch sensor setting is incorrect,

you can to execute the Adjust touch sensor

option to manual adjust touch sensor area.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Adjust

touch sensor option to manual adjust touch

sensor area.

S520 Laser Touch QSC_A02-APCC.book Page 11 Thursday, May 8, 2014 4:54 PM

Set Up Laser Touch on Your Projector

12

Touch sensor adjustment instruction screen

shown below appears, and follow the on-

screen instruction to complete settings.

Part J: Install the Workspace

Application Software on Your

Computer

The WorkSpace Application software is

bundled along with the CD that shipped with

your projector. Install the WorkSpace

Application Software and follow the on-screen

instructions to complete the setup. For more

instructions, refer to "WorkSpace Getting

Started Guide".

S520 Laser Touch QSC_A02-APCC.book Page 12 Thursday, May 8, 2014 4:54 PM

Troubleshooting

13

Troubleshooting

If you experience problems with Touch, see the following troubleshooting tips. If the problem

persists, contact Dell (see Projector User's Guide Contacting Dell on page 122).

Problem Possible Solution

The touch functionality on the edge or

corner of image is not working.

Please refer to Part F to execute the auto adjust

touch or touch area by manual or project at ~84" if

whiteboard bezel is affecting touch functionality on

the edge of the image.

If there is a big gap between the cursor

and touch point.

Please refer to Part F to execute the auto adjust

touch.

S520 Laser Touch QSC_A02-APCC.book Page 13 Thursday, May 8, 2014 4:54 PM

Troubleshooting

14

If the line drawn is not continuos, broken,

or if you encounter problems with the

Touch function in other areas of the

projected image.

1 Check for presence of foreign objects on the

whiteboard.

2 Please refer to Part I to execute the Adjust

touch sensor area.

3 If there is halogen lamp near the projector and

whiteboard, light from the halogen lamp may

affect touch performance. If so,

a Turn off the halogen lamp.

b Shielding the halogen lamp light to

whiteboard or camera.

c Reduce Touch Sensitivity in driver. Doing so

may however affect touch performance at

whiteboard corners.

Problem (continued) Possible Solution (continued)

S520 Laser Touch QSC_A02-APCC.book Page 14 Thursday, May 8, 2014 4:54 PM

Dell™ | インタラクティブプロジェクタ

S520

レーザータッチセットアップガイド

S520 Laser Touch QSC_A02-APCC.book Page 1 Thursday, May 8, 2014 4:54 PM

注について

メモ: 「メモ」は、プロジェクタの使用に際して役立つ重要な情報です。

______________ ____

本書の内容は予告なく変更されることがあります。

Dell Inc. 社の書面による許諾を受けることなく、どのような形態であっても、本書を複製するこ

とは固く禁じられています。

本書で使用されている商標 :Dell および DELL ロゴは、Dell Inc の商標です。 Microsoft、

Windows 7、および Windows Vista は、米国および / またはその他の国における Microsoft

Corporation の商標または登録商標です。

本書で使用されているその他の商標および製品名はそれぞれの所有者に帰属しています。 Dell

Inc. は他社の所有する商標や製品名の所有権をすべて放棄します。

2014 年 6 月 P/N 05PF0 Rev. A02

S520 Laser Touch QSC_A02-APCC.book Page 2 Thursday, May 8, 2014 4:54 PM

プロジェクタへのレーザータッチのセットアップ

3

メモ: コンピュータには以下の最低システ

ム要件を満たしている必要があります。

オペレーティングシステム：

• Windows XP Professional service pack 3

32 ビット、Windows 7 32 ビット/

64 ビット、Windows 8 32 ビット/

64 ビット

• Windows .NET Framework 4.0 をインス

トールする必要があります(Microsoft

サイトからダウンロードできます)

•MacOS 10.6以上

最低ハードウェア：

•Windowsプロセッサータイプ :Intel

Core i3 以上

•MACプロセッサータイプ:Intel Core i2

duo 以上

• Windows/MAC RAM:RAM 2GB （必須）

以上推奨

• Windows/MAC の最小 HDD 容量 :

110 MB の空きハードディスク容量

パート A: ホワイトボードの

取り付け

1 ホワイトボードを取り付けます。

メモ: 「ホワイトボード取り付け手順」を

参照してください。

プロジェクタへのレーザータッチのセットアップ

S520 Laser Touch QSC_A02-APCC.book Page 3 Thursday, May 8, 2014 4:54 PM

プロジェクタへのレーザータッチのセットアップ

4

パート B ：プロジェクタの

取り付け

2 ウォールマウントおよびプロジェクタを取

り付けます。

メモ: ウォールマウントはプロジェクタに

付属しています。「ウォールマウント取り付

け手順」を参照してください。

メモ: 最大画像投影を行う場合は 87 インチ

で投影します。最適なタッチ体験のため、

投影画像の周囲に境界を残す場合は、 84

インチ以下で投影します。

パート C ：レーザーカーテン

キットの取り付け

3 ホワイトボード上にレーザーカーテン

キットを取り付けます。

注：

a アタッチメントは、位置決めピンおよび

磁石で補助されます。

b また、セキュリティネジでキットを

ロックすることができます。

c レーザーカーテンキット用のカバーが

あります。

(b) ネジ

(a)

S520 Laser Touch QSC_A02-APCC.book Page 4 Thursday, May 8, 2014 4:54 PM

ページを読み込んでいます...

Dell S520 Projector クイックスタートガイド

関連論文