DeWalt DHS790N ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
DHS790
Final Page Size: 8.5 x 11in
B
English 1
繁體中文 18
1
2
3
19
18
20
22
23
21
24
262725
Fig. A
A
1
ENGLISH
English (original instructions)
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or seriousinjury.
WARNING: To reduce the risk of injury, read the
instructionmanual.
1 Operating handle
2 Trigger switch
3 Trigger lock-off button
4 Lower guard
5 Mounting holes
6 Miter lock lever
7 Miter release button
8 Miter detent override lever
9 Kerf plate
10 Miter scale pointer
11 Miter scale
12 Miter scale screws
13 Base extensions
14 Fence
15 Bevel scale
16 Bevel scale pointer
17 Lock down pin
18 Lifting handle
19 CUTLINE™ worklight switch
20 Battery packs
21 Rails
22 Rail lock knob
23 Rail adjustment screw
24 Dust port
25 Hex wrench
26 Bevel lock knob
27 Clamp hole
28 Hand indentation
Fig. A
4
5
15
16
17
514
13 101112
58 679
28
2
ENGLISH
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) powertool.
Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas inviteaccidents.
b ) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
orfumes.
c ) Keep children and bystanders away while operating a power tool. Distractions can
cause you to losecontrol.
Electrical Safety
d ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electricshock.
e ) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
orgrounded.
f ) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electricshock.
g ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electricshock.
h ) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electricshock.
i ) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of
electricshock.
Personal Safety
j ) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personalinjury.
k ) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personalinjuries.
l ) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the
switch on invitesaccidents.
m ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personalinjury.
n ) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpectedsituations.
o ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
movingparts.
p ) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
relatedhazards.
q ) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe injury
within a fraction of asecond.
Power Tool Use and Care
r ) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it wasdesigned.
Technical Data
DHS790
Voltage VDC 2 x 54 (60V Max)
Battery Type Li-Ion
Blade diameter mm 305
Blade bore mm 25.4
Blade body thickness mm 1.75
Max. blade speed min-1 3 800
Max. cross-cut capacity 90° mm 345
Max. mitre capacity 45° mm 244
Max. depth of cut 90° mm 112
Max. depth of bevel cross-cut 45° mm 56
Mitre (max. positions) left 50°
right 60°
Bevel (max. positions) left 49°
right 49°
Automatic blade brake time s< 5
Weight (without battery packs or corded power supply) kg 25.3
Batteries Chargers/Charge Times (Minutes)
Cat # VDC Ah Weight (kg) DCB107 DCB112 DCB115 DCB118 DCB132 DCB119
DCB546 18/54 6.0/2.0 1.05 270 140 90 60 90 X
DCB606 20/60 6.0/2.0 1.05 270 140 90 60 90 X
DCB547 18/54 9.0/3.0 1.25 420 220 140 85 140 X
DCB609 20/60 9.0/3.0 1.25 420 220 140 85 140 X
DCB181 18 1.5 0.35 70 35 22 22 22 45
DCB182 18 4.0 0.61 185 100 60 60 60 120
DCB204 20 4.0 0.61 185 100 60 60 60 120
DCB183/B 18 2.0 0.40 90 50 30 30 30 60
DCB203 20 2.0 0.40 90 50 30 30 30 60
DCB184/B 18 5.0 0.62 240 120 75 75 75 150
DCB205 20 5.0 0.62 240 120 75 75 75 150
DCB185 18 1.3 0.35 60 30 22 22 22 X
DCB187 18 3.0 0.48 140 70 45 45 45 90
3
ENGLISH
s ) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must berepaired.
t ) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power toolaccidentally.
u ) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
v ) Maintain power tools and accesories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained powertools.
w ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier tocontrol.
x ) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardoussituation.
y ) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpectedsituations.
Battery Tool Use and Care
z ) Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
batterypack.
aa ) Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury andfire.
ab ) When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or afire.
ac ) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation orburns.
ad ) Do not use a battery pack or tool that is damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior resulting in fire, explosion or risk ofinjury.
ae ) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire
or temperature above 265 °F (130°C) may causeexplosion.
af ) Follow all charging instructions and do not charge the battery pack or tool outside
the temperature range specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the battery and increase the risk of
fire.
Service
ag ) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool ismaintained.
ah ) Never service damaged battery packs. Service of battery packs should only be performed
by the manufacturer or authorized serviceproviders.
Safety Instructions for Miter Saws
a ) Miter saws are intended to cut wood or wood-like products, they cannot be used
with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs,
etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive
cutting will burn the lower guard, the kerf insert and other plasticparts.
b ) Use clamps to support the workpiece whenever possible. If supporting the
workpiece by hand, you must always keep your hand at least 4" (100 mm) from
either side of the saw blade. Do not use this saw to cut pieces that are too small to
be securely clamped or held by hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from bladecontact.
c ) The workpiece must be stationary and clamped or held against both the fence and
the table. Do not feed the workpiece into the blade or cut “freehand” in any way.
Unrestrained or moving workpieces could be thrown at high speeds, causinginjury.
d ) Push the saw through the workpiece. Do not pull the saw through the workpiece. To
make a cut, raise the saw head and pull it out over the workpiece without cutting,
start the motor, press the saw head down and push the saw through the workpiece.
Cutting on the pull stroke is likely to cause the saw blade to climb on top of the workpiece
and violently throw the blade assembly towards theoperator.
e ) Never cross your hand over the intended line of cutting either in front or behind the
saw blade. Supporting the workpiece “cross handed” i.e. holding the workpiece to the right
of the saw blade with your left hand or vice versa is verydangerous.
f ) Do not reach behind the fence with either hand closer than 100 mm from either side
of the saw blade, to remove wood scraps, or for any other reason while the blade
is spinning. The proximity of the spinning saw blade to your hand may not be obvious and
you may be seriouslyinjured.
g ) Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp
it with the outside bowed face toward the fence. Always make certain that there
is no gap between the workpiece, fence and table along the line of the cut. Bent or
warped workpieces can twist or shift and may cause binding on the spinning saw
blade while cutting. There should be no nails or foreign objects in theworkpiece.
h ) Do not use the saw until the table is clear of all tools, wood scraps, etc., except
for the workpiece. Small debris or loose pieces of wood or other objects that contact the
revolving blade can be thrown with highspeed.
i ) Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or shift duringcutting.
j ) Ensure the miter saw is mounted or placed on a level, firm work surface before use.
A level and firm work surface reduces the risk of the miter saw becomingunstable.
k ) Plan your work. Every time you change the bevel or miter angle setting, make sure
the fence will not interfere with the blade or the guarding system. Without turning
the tool “ON” and with no workpiece on the table, move the saw blade through a complete
simulated cut to assure there will be no interference or danger of cutting thefence.
l ) Provide adequate support such as table extensions, saw horses, etc. for a workpiece
that is wider or longer than the table top. Workpieces longer or wider than the miter
saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the
lower guard or be thrown by the spinningblade.
m ) Do not use another person as a substitute for a table extension or as additional
support. Unstable support for the workpiece can cause the blade to bind or the workpiece to
shift during the cutting operation pulling you and the helper into the spinningblade.
n ) The cut-off piece must not be jammed or pressed by any means against the
spinning saw blade. If confined, i.e. using length stops, the cut-off piece could get wedged
against the blade and thrownviolently.
o ) Always use a clamp or a fixture designed to properly support round material such
as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to “bite”
and pull the work with your hand into theblade.
p ) Let the blade reach full speed before contacting the workpiece. This will reduce the risk
of the workpiece beingthrown.
q ) If the workpiece or blade becomes jammed, turn the miter saw off. Wait for all
moving parts to stop and disconnect the plug from the power source and/or remove
the battery pack. Then work to free the jammed material. Continued sawing with a
jammed workpiece could cause loss of control or damage to the mitersaw.
r ) After finishing the cut, release the switch, hold the saw head down and wait for
the blade to stop before removing the cut-off piece. Reaching with your hand near the
coasting blade isdangerous.
s ) Hold the handle firmly when making an incomplete cut or when releasing the
switch before the saw head is completely in the down position. The braking action of
the saw may cause the saw head to be suddenly pulled downward, causing a risk ofinjury.
Additional Safety Rules for Miter Saws
WARNING: Do not allow familiarity (gained from frequent use of your saw) to replace
safety rules. Always remember that a careless fraction of a second is sufficient to inflict
severeinjury.
WARNING: Never modify the power tool or any part of it. Damage or personal injury
couldresult.
DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to
the instructions. A machine incorrectly assembled can cause seriousinjury.
OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not
thoroughly familiar with the operation of this machine. Knowledge issafety.
FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock
or electrocution. Protect electric supply line with at least a 15 ampere time-delay fuse or a
circuitbreaker.
MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade should point in
the direction of rotation as marked on thesaw.
TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps can cause
parts or the workpiece to be thrown at highspeeds.
BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are against blade
and arbor screw is tightened securely. Loose or improper blade clamping may result in damage
to the saw and possible personalinjury.
DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE for the saw.
Overheating, damage to the tool and personal injury mayoccur.
DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage to tool and
possible personal injury mayoccur.
NEVER CUT FERROUS METALS or masonry. Either of these can cause the carbide tips to fly off
the blade at high speeds causing seriousinjury.
NEVER PLACE HANDS CLOSER THAN 4" (100 mm) FROM THEBLADE.
NEVER HAVE ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW BLADE.
Personal injury willoccur.
NEVER APPLY BLADE LUBRICANT TO A RUNNING BLADE. Applying lubricant could cause
your hand to move into the blade resulting in seriousinjury.
DO NOT place either hand in the blade area when the saw is connected to the power source.
Inadvertent blade activation may result in seriousinjury.
NEVER REACH AROUND OR BEHIND THE SAW BLADE. A blade can cause seriousinjury.
4
ENGLISH
DO NOT REACH UNDERNEATH THE SAW unless it is unplugged and turned off. Contact with
saw blade may cause personalinjury.
SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can possibly cause
the machine to slide, walk, or tip over, causing seriousinjury.
USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best results, do not
use carbide tipped blades with hook angles in excess of 7 degrees. Do not use blades with deep
gullets. These can deflect and contact the guard, and can cause damage to the machine and/or
seriousinjury.
USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to prevent
damage to the machine and/or seriousinjury.
INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or damaged
blade can come apart and pieces can be thrown at high speeds, causing serious injury. Replace
cracked or damaged bladesimmediately.
CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade and blade
clamps allows you to check for any damage to the blade or blade clamps. A cracked or damaged
blade or blade clamp can come apart and pieces can be thrown at high speeds, causing
seriousinjury.
DO NOT USE WARPED BLADES. Check to see if the blade runs true and is free from vibration. A
vibrating blade can cause damage to the machine and/or seriousinjury.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.
KEEP GUARD IN PLACE and in workingorder.
ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED. Small chip
accumulation under the saw may interfere with the saw blade or may cause instability of
workpiece whencutting.
USE ONLY BLADE CLAMPS SPECIFIED FOR THIS TOOL to prevent damage to the machine
and/or seriousinjury.
CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can cause the
machine to overheat, damaging the machine and possibly causing a short which could cause
seriousinjury.
NEVER LOCK THE SWITCH IN THE “ON” POSITION. Severe personal injury mayresult.
NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionallycontacted.
WARNING: Cutting plastics, sap coated wood, and other materials may cause melted
material to accumulate on the blade tips and the body of the saw blade, increasing the risk
of blade overheating and binding whilecutting.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETYEQUIPMENT:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicalsare:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treatedlumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopicparticles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmfulchemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face andbody.
WARNING: Always wear proper personal hearing protection during use. Under some
conditions and duration of use, noise from this product may contribute to hearingloss.
Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long
hair can be caught in movingparts.
The label on your tool may include the following symbols. The symbols and their definitions are
asfollows:
V ......................... volts
Hz .......................hertz
min ..................... minutes
or DC ......direct current
...................... Class I Construction (grounded)
…/min ..............per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or direct current
...................... Class II Construction (double insulated)
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory protection
..................... wear eye protection
..................... wear hearing protection
..................... read all documentation
For your convenience and safety, the following warning labels are on your mitersaw.
ON MOTOR HOUSING:
TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. WEAR EYE
PROTEXCTION AND RESPIRATORY PROTECTION. USE ONLY IDENTICAL REPLACEMENT PARTS.
DO NOT EXPOSE TO RAIN OR USE IN DAMPLOCATIONS.
ON MOVING FENCES:
ALWAYS ADJUST FENCE PROPERLY BEFORE USE. CLAMP SMALL PIECES BEFORE CUTTING.
SEEMANUAL.
ON GUARD:
DANGER–KEEP AWAY FROM BLADE.
ON UPPER GUARD:
PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFOREUSE.
ON TABLE: (2 PLACES)
WARNING: KEEP HANDS AND BODY OUT OF THE PATH OF THE
SAW BLADE. CONTACT WITH BLADE WILL RESULT IN SERIOUS
INJURY. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.
CHECK GUARDING SYSTEM TO MAKE SURE IT IS FUNCTIONING
CORRECTLY. DO NOT PERFORM ANY OPERATION FREEHAND.
NEVER REACH IN BACK OF SAW BLADE TURN OFF TOOL
AND WAIT FOR SAW BLADE TO STOP BEFORE MOVING WORKPIECE OR CHANGING
SETTINGS OR MOVING HANDS. NEVER CROSS ARMS IN FRONT OF BLADE. ALWAYS
TIGHTEN ADJUSTMENT KNOBS BEFORE EACH USE. DISCONNECT POWER BEFORE
CHANGING BLADE ORSERVICING.
ON TABLE: (2 PLACES)
Electrical Connection
Be sure your power source agrees with the nameplate marking. AC means that your saw will
operate on alternating current. Do not operate with DC power. A voltage decrease of 10 percent
or more will cause a loss of power and overheating. All DeWALT tools are factory tested. If this
tool does not operate, check the powersupply.
This miter saw operates on either two 60V battery packs or by using the DeWALT corded
powersupply.
Using the Corded Power Supply (Fig. B)
The DeWALT corded power supply is designed to provide power for DeWALT 120V Max*
FLEXVOLT cordless tools. Insert the corded power supply into the miter saw battery slot (refer to
Installing and Removing the Corded Power Supply into and from Tool and plug the power
supply into an AC outlet. The power supply will act as the power source to the tool. Your DeWALT
corded power supply should only be used with standard household power or a generator.
The corded power supply is suitable for use with both grounded and double insulated tools.
When the power supply is utilized with a grounded tool, the tool inlet will be equipped with a
ground prong that allows the ground path from the tool to connect to the power supply. When
the power supply is used with this double insulated miter saw, no ground connection is made
from the tool to the power supply as no ground connection isrequired.
Fig. B
Additional Specific Usage Instructions
The corded power supply may become warm to the touch during use. This is a normal condition
and does not indicate aproblem.
IMPORTANT. The power supply is not user serviceable. There are no user serviceable parts inside
the powersupply.
Servicing at an authorized service center is required to avoid damage to static sensitive
internalcomponents.
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton. Before using the battery pack and charger,
read the safety instructions below and then follow charging proceduresoutlined. When ordering
replacement battery packs, be sure to include the catalog number andvoltage.
5
ENGLISH
Your tool uses a DeWALT charger. Be sure to read all safety instructions before using your charger.
Consult the chart at the end of this manual for compatibility of chargers and batterypacks.
READ ALL INSTRUCTIONS
Important Safety Instructions for All Battery Packs
WARNING: Read all safety warnings and all instructions for the battery pack,
charger and power tool. Failure to follow the warnings and instructions may result
in electric shock, fire and/or seriousinjury.
Do not charge or use the battery pack in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger
may ignite the dust orfumes.
NEVER force the battery pack into the charger. DO NOT modify the battery pack in any
way to fit into a non-compatible charger as battery pack may rupture causing serious
personal injury. Consult the chart at the end of this manual for compatibility of batteries
andchargers.
Charge the battery packs only in designated DeWALTchargers.
DO NOT splash or immerse in water or otherliquids.
Do not store or use the tool and battery pack in locations where the temperature may
reach or exceed 104°F (40°C) (such as outside sheds or metal buildings in summer). For
best life store battery packs in a cool, drylocation.
NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never
tape the trigger switch in the ONposition.
Do not expose battery pack or tool/appliance to fire or excessive temperature. Exposure
to fire or temperature above 265°F (130°C) may cause explosion.
Do not incinerate the battery pack even if it is severely damaged or is completely worn
out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium
ion battery packs areburned.
If battery contents come into contact with the skin, immedicately wash area with mild
soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes
or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a
mixture of liquid organic carbonates and lithiumsalts.
Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If
symptoms persist, seek medicalattention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark orflame.
WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the
battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop
or damage the battery pack. Do not use a battery pack or charger that has received a sharp
blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with
a hammer, stepped on). Damaged battery packs should be returned to the service center
forrecycling.
Transportation
WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects
can contact exposed battery terminals. For example, do not place the battery pack
in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can possibly cause fires if the battery terminals
inadvertently come in contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation Hazardous Material Regulations
(HMR) actually prohibit transporting batteries in commerce or on airplanes in carry-on
baggage UNLESS they are properly protected from short circuits. So when transporting
individual battery packs, make sure that the battery terminals are protected and well
insulated from materials that could contact them and cause a shortcircuit.
NOTE: Lithium-ion batteries should not be put in checkedbaggage.
Shipping the DeWALT FLEXVOLT® Battery
The DeWALT FLEXVOLT® battery has two modes: Use and Shipping.
Use Mode: When the FLEXVOLT® battery stands alone or is in a DeWALT 20V Max* product, it will
operate as a 20V Max* battery. When the FLEXVOLT® battery is in a 60V Max* or a 120V Max* (two
60V Max* batteries) product, it will operate as a 60V Max* battery.
Shipping Mode: When the cap is attached to the FLEXVOLT®
battery, the battery is in Shipping Mode. Strings of cells are
electrically disconnected within the pack resulting in three
batteries with a lower Watt hour (Wh) rating as compared to one
battery with a higher Watt hour rating. This increased quantity
of three batteries with the lower Watt hour rating can exempt the pack from certain shipping
regulations that are imposed upon the higher Watt hourbatteries.
The battery label indicates two Watt hour ratings (see example). Depending on how the battery
is shipped, the appropriate Watt hour rating must be used to determine the applicable shipping
requirements. If utilizing the shipping cap, the pack will be considered 3 batteries at the Watt
hour rating indicated for “Shipping”. If shipping without the cap or in a tool, the pack will be
considered one battery at the Watt hour rating indicated next to “Use”.
USE: 120 Wh Shipping: 3 x 40 Wh
Example of Use and Shipping Label Marking
For example, Shipping Wh rating might indicate 3 x 40 Wh, meaning 3 batteries of 40 Watt hours
each. The Use Wh rating might indicate 120 Wh (1 battery implied).
Fuel Gauge Battery Packs (Fig. C)
Some DeWALT battery packs include a fuel gauge which consists of three green LED lights that
indicate the level of charge remaining in the batterypack.
The fuel gauge is an indication of approximate levels of charge remaining in the battery pack
according to the followingindicators:
75–100% charged
51–74% charged
< 50% charged
Pack needs to be charged
To actuate the fuel gauge, press and hold the fuel gauge button. A combination of the three
green LED lights will illuminate designating the level of charge left. When the level of charge in
the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need
to berecharged.
Fig. C
NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not
indicate tool functionality and is subject to variation based on product components, temperature
and end-userapplication.
For more information regarding fuel gauge battery packs, please visit our website www.dewalt.
com.
Important Safety Instructions for All Battery Chargers
WARNING: Read all safety warnings and all instructions for the battery pack,
charger and power tool. Failure to follow the warnings and instructions may result
in electric shock, fire and/or seriousinjury.
DO NOT attempt to charge the battery pack with any chargers other than the ones in
this manual. The charger and battery pack are specifically designed to worktogether.
These chargers are not intended for any uses other than charging DeWALT
rechargeable batteries. Any other uses may result in risk of fire, electric shock orelectrocution.
Do not expose the charger to rain orsnow.
Pull by the plug rather than the cord when disconnecting the charger. This will reduce the
risk of damage to the electric plug andcord.
Make sure that the cord is located so that it will not be stepped on, tripped over or
otherwise subjected to damage orstress.
Do not use an extension cord unless it is absolutely necessary. Use of improper extension
cord could result in risk of fire, electric shock orelectrocution.
When operating a charger outdoors, always provide a dry location and use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the
risk of electricshock.
Do not place any object on top of the charger or place the charger on a soft surface that
might block the ventilation slots and result in excessive internal heat. Place the charger
in a position away from any heat source. The charger is ventilated through slots in the top and
the bottom of thehousing.
Do not operate the charger with a damaged cord orplug.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorized servicecenter.
Do not disassemble the charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution
orfire.
Disconnect the charger from the outlet before attempting any cleaning. This will reduce
the risk of electric shock. Removing the battery pack will not reduce thisrisk.
NEVER attempt to connect 2 chargerstogether.
The charger is designed to operate on standard household electrical power. Do not
attempt to use it on any other voltage. This does not apply to the vehicularcharger.
WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock
mayresult.
WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid
to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a service center forrecycling.
6
ENGLISH
CAUTION: Burn hazard. To reduce the risk of injury, charge only DeWALT rechargeable
battery packs. Other types of batteries may overheat and burst resulting in personal injury
and propertydamage.
NOTICE: Under certain conditions, with the charger plugged into the power supply, the
charger can be shorted by foreign material. Foreign materials of a conductive nature, such
as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of
metallic particles should be kept away from the charger cavities. Always unplug the charger
from the power supply when there is no battery pack in the cavity. Unplug the charger before
attempting toclean.
Charging a Battery (Fig. D)
1. Plug the charger into an appropriate outlet before inserting batterypack.
FIG. D
2. Insert the battery pack into the charger, making sure the battery pack is fully seated in the
charger. The red (charging) light will blink continuously indicating that the charging process
hasstarted.
3. The completion of charge will be indicated by the red light remaining ON continuously. The
battery pack is fully charged and may be used at this time or left in the charger. To remove
the battery pack from the charger, push the battery release button on the battery pack and
then slide the battery pack out of thecharger.
NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery
pack fully before firstuse.
Charger Operation
Refer to the indicators below for the charge status of the batterypack.
DCB107, DCB112, DCB113, DCB115, DCB118, DCB132
Charging
Fully Charged
Hot/Cold Pack Delay*
* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132: The red light will continue to blink,
but a yellow indicator light will be illuminated during this operation. Once the battery pack has
reached an appropriate temperature, the yellow light will turn off and the charger will resume
the chargingprocedure.
The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty
battery pack by refusing tolight.
NOTE: This could also mean a problem with acharger.
If the charger indicates a problem, take the charger and battery pack to be tested at an
authorized servicecenter.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the pack charging mode. This feature
ensures maximum battery packlife.
A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will
charge at that slower rate throughout the entire charging cycle and will not return to maximum
charge rate even if the battery packwarms.
The DCB118 charger is equipped with an internal fan designed to cool the battery pack. The fan
will turn on automatically when the battery pack needs to becooled.
Never operate the charger if the fan does not operate properly or if ventilation slots are blocked.
Do not permit foreign objects to enter the interior of thecharger.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection System that will protect the battery pack
against overloading, overheating or deepdischarge.
The tool will automatically turn off if the Electronic Protection System engages. If this occurs,
place the lithium-ion battery pack on the charger until it is fullycharged.
Wall Mounting
DCB107, DCB112, DCB113, DCB115, DCB118, DCB132
These chargers are designed to be wall mountable or to sit upright on a table or work surface. If
wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or
other obstructions which may impede air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the charger securely using drywall screws
(purchased separately) at least 1" (25.4 mm) long, with a screw head diameter of 0.28–0.35"
(7–9mm), screwed into wood to an optimal depth leaving approximately 7/32" (5.5 mm) of
the screw exposed. Align the slots on the back of the charger with the exposed screws and fully
engage them in theslots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the charger using a cloth or soft non-
metallic brush. Do not use water or any cleaningsolutions.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65°F and 75°F (18° 24°C). DO NOT charge the battery pack
below +40°F (+4.5°C), or above +104°F (+40°C). This is important and will prevent serious
damage to the batterypack.
2. The charger and battery pack may become warm to the touch while charging. This is a
normal condition, and does not indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in a warm environment such as in a
metal shed or an uninsulatedtrailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you
turn out the lights;
c. Move the charger and battery pack to a location where the surrounding air temperature is
approximately 65°F – 75°F (18° – 24°C);
d. If charging problems persist, take the tool, battery pack and charger to your local
servicecenter.
4. The battery pack should be recharged when it fails to produce sufficient power on jobs which
were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack whenever you desire with no
adverse effect on the batterypack.
5. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal
chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away
from charger cavities. Always unplug the charger from the power supply when there is no
battery pack in the cavity. Unplug the charger before attempting toclean.
6. Do not freeze or immerse the charger in water or any otherliquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat
orcold.
2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place
out of the charger for optimalresults.
NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will
need to be recharged beforeuse.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Specifications
Capacity of cut
50º miter left, 60º miter right,
49º bevel left and right
Angle Maximum Capacity of Cut Result
0° miter Height 4.4" (112 mm) Width 9.1" (231 mm)
Width 13.75" (349 mm) Height 3.0" (76 mm)
45° miter Height 4.4" (112 mm) Width 5.8" (147 mm)
Width 9.6" (244 mm) Height 3.0" (76 mm)
45º bevel
– left
Height 3.1" (79 mm) Width 11.4" (290 mm)
Width 13.75" (349 mm) Height 1.7" (43 mm)
45º bevel –
right
Height 2.2" (56 mm) Width 11.4" (290 mm)
Width 13.75" (349 mm) Height 1.1" (28 mm)
Your saw is capable of cutting baseboard moldings held vertically 0.8" (20 mm) thick by 6.75"
(171 mm) tall on a 45º right or left miter, when using the slide lock lever (40, Fig.J).
7
ENGLISH
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts. In
addition to this instruction manual, the carton should contain:
1 DHS790 miter saw
1 Base extension (right)
1 Base extension (left)
May include:
1 DeWALT Corded power supply (excluding N version)
2 60V batteries (excluding N version)
1 Dual port charger (excluding N version)
In bag:
1 Blade wrench
2 Clamps
2 Lock washers
2 Wing nuts
1 Material clamp
1 Dustbag
1 Instruction manual
Intended Use
This miter saw is designed for professional sawingapplications.
DO NOT use under wet conditions or in presence of flammable liquids orgases.
This miter saw is a professional power tool. DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use thistool.
Familiarization (Fig. A, E)
Your miter saw is not fully assembled in the carton. Refer to the Assembly section for assembly
instructions. Open the box and lift the saw out by the convenient lifting handle18, as shown in
FigureE. Place the saw on a smooth, flat surface such as a workbench, strong table or DeWALT
miter saw stand. Examine FigureA to become familiar with the saw and its various parts. The
section on adjustments will refer to these terms and you must know what and where the
partsare.
Fig. E
18
CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the operating
handle1 when pulling the handle down. The lower guard will move up as the handle
is pulled down which could cause pinching.The handle is placed close to the guard for
specialcuts.
Press down lightly on the operating handle1 and pull out the lock down pin17. Gently release
the downward pressure and hold the arm allowing it to rise to its full height. Use the lock down
pin when carrying the saw from one place to another. Always use the lifting handle18 or the
hand indentations28 to transport thesaw.
Transporting the Saw (Fig.A, H)
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
WARNING: To reduce the risk of serious personal injury, ALWAYS lock the rail lock
knob22, miter lock lever6, bevel lock knob26, lock down pin17 and fence
adjustment knobs (53, Fig.H) before transportingsaw.
In order to conveniently carry the miter saw from place to place, a lifting handle18 has been
included on the top of the saw arm and hand indentations28 in thebase.
To transport the saw, lower the arm of the saw and press in the lock down pin17 to secure
thearm.
Head Lock Down Pin (Fig. A)
WARNING: The lock down pin should be used ONLY when carrying or storing the
saw. NEVER use the lock down pin for any cuttingoperation.
To lock the saw head in the down position, push the head down, push the lock down pin17 in
and release the saw head. This will hold the saw head safely down for moving the saw from place
to place. To release, press the saw head down and pull the pinout.
ASSEMBLY
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of manufacture.
If readjustment due to shipping and handling or any other reason is required, follow the steps
below to adjust yoursaw.
Once made, these adjustments should remain accurate. Take a little time now to follow these
directions carefully to maintain the accuracy of which your saw iscapable.
Assembling the Base Extensions (Fig. F)
WARNING: Base extensions must be assembled to both sides of the saw's base before using
thesaw.
1. Locate the preassembled threaded stud55 underneath the saw’sbase.
2. The extension13 should be oriented as shown in the illustration, sliding fully rearward in the
U-shaped supports.
3. Clamp the extension’s rods against the miter saw base by inserting the clamp56 over the
threaded stud, followed by the washer57 , and tightening the wing nut58 . Ensure the
extension is secure by pulling on the extension to verify no movement.
4. Repeat steps 1 through 3 on the other side.
13
Fig. F
56
58
57
55
Bench Mounting (Fig. A)
Mounting holes 5 are provided in all 4 feet to facilitate bench mounting. (Two different-sized
holes are provided to accommodate different sizes of screws. Use either hole, it is not necessary
to use both.) Always mount your saw firmly to a stable surface to prevent movement. To enhance
the tool’s portability, it can be mounted to a piece of 1/2" (12.7 mm) or thicker plywood which
can then be clamped to your work support or moved to other job sites andreclamped.
NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting
screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work
support. When clamping the saw to any work surface, clamp only on the clamping bosses where
the mounting screw holes are located. Clamping at any other point will interfere with the proper
operation of thesaw.
CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped
or otherwise uneven. If the saw rocks on the surface, place a thin piece of material under one
saw foot until the saw sits firmly on the mountingsurface.
FEATURES AND CONTROLS
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
Use of CUTLINE™ LED Worklight (Fig.A)
CAUTION: Do not stare into worklight. Serious eye injury couldresult.
The CUTLINE™ LED Worklight can be turned on by the momentary switch19. The light will
automatically turn off within 20 seconds if the saw is not in use. The light is also activated
automatically every time the tool's main trigger2 ispulled.
To cut through an existing pencil line on a piece of wood, turn on the CUTLINE™ worklight
using the momentary switch19 (not with the main trigger), then pull down on the operating
8
ENGLISH
handle1 to bring the saw blade close to the wood. The shadow of the blade will appear on the
wood. This shadow line represents the material that the blade will remove when performing
a cut. To correctly locate your cut to the pencil line, align the pencil line with the edge of the
blade’s shadow. Keep in mind that you may have to adjust the miter or bevel angles in order to
match the pencil lineexactly.
Your saw is equipped with a battery monitoring feature. The CUTLINE™ worklight begins to
flash when the battery is near the end of its useful charge and/or when the battery is too hot.
Charge the battery prior to continuing cutting applications. Refer to Charging Procedure under
Important Safety Instructions for All Battery Chargers for battery charginginstructions.
Miter Control (Fig.G)
The miter lock lever and miter release button allow you to miter your saw to 60° right and 50° left.
To miter the saw, lift the miter lock lever6, push the miter release button7 and move the miter
arm to the angle desired on the miter scale11 as shown at the miter scale pointer10. Push
down on the miter lock lever to lock the miter arm inplace.
Fig. G
11 10 8 7 6
12
Miter Detent Override (Fig.G)
The miter detent override lever8 allows your saw to override the common stop angles (detents).
To override the detents, unlock the miter lock lever6 by pulling upward. Push the miter detent
override lever8 up, and move the miter arm to the angle desired on the miter scale11. Push
down on the miter lock lever to lock the miter arm inplace.
Bevel Lock (Fig.H)
The bevel lock allows you to bevel the saw 49° left or right. To adjust the bevel setting, turn the
bevel lock knob26 counterclockwise. The saw head will then bevel easily to the left or to the
right. To tighten, turn the bevel lock knobclockwise.
0° Bevel Override (Fig.H)
The bevel override allows you to bevel the saw to the right, past the 0°mark.
When the 0° bevel override lever29 is engaged (the lever will be turned up), the saw will
automatically stop at 0° when brought up from the left. To move past 0° to the right, bevel the
saw slightly to the left of 0°, then pull the 0° bevel override lever29 out. The saw head can now
be beveled past 0° to the right. Lock the saw head at the desired angle by turning the bevel lock
knob26 clockwise to tighten. The 0° bevel override lever can be locked out by twisting the lever
so it facesdown.
Fig. H
14
53
53
30
29
2630
45° Bevel Override (Fig.H)
There are two 45° bevel override levers30 one on each side of the saw. To bevel the saw, left
or right, past 45°, push the 45° bevel override lever30 rearward. When in the rearward position,
the saw can bevel past these stops. When the 45° stops are needed, pull the 45° bevel override
leverforward.
Crown Bevel Pawls (Fig.I)
When cutting crown molding laying flat, your saw is equipped to accurately and rapidly set
a crown stop, left or right (refer to Instructions for Cutting Crown Molding Laying Flat
and Using the Compound Features under Cutting Crown Molding). The 33.9° crown bevel
pawl31 can be rotated to contact the crown adjustment screw36. The saw is factory set to be
used for typical crown in North America (52/38), but can be reversed to cut non-typical (45/45)
crown. To reverse the 33.9° crown bevel pawl, remove the retaining screw34, the 22.5° bevel
pawl32 and the 33.9° crown bevel pawl31. Flip the 33.9° crown bevel pawl so the 30° text
is facing up. Reattach the screw to secure the 22.5° bevel pawl and the crown bevel pawl. The
accuracy setting will not beaffected.
Fig. I
15
16
32
36
33
37
29
35
34
31
22.5° Bevel Pawls (Fig.I)
Your saw is equipped to rapidly and accurately set a 22.5° bevel, left or right. The 22.5° bevel
pawl32 can be rotated to contact the crown adjustment screw36.
Rail Lock Knob (Fig.A)
The rail lock knob22 allows you to lock the saw head firmly to keep it from sliding on the rails.
This is necessary when making certain cuts or when transporting thesaw.
Depth Stop (Fig.J)
The depth stop allows the depth of cut of the blade to be limited. The stop is useful for
applications such as grooving and tall vertical cuts. Rotate the depth stop40 forward and adjust
the depth adjustment screw41 to set the desired depth of cut. To secure the adjustment,
tighten the wing nut42. Rotating the depth stop to the rear of the saw will bypass the depth
stop feature. If the depth adjustment screw is too tight to loosen by hand, the provided blade
wrench can be used to loosen thescrew.
Fig. J
42
41
40
Slide Lock Lever (Fig.K)
The slide lock lever43 places the saw in a position to maximize cutting of base molding when
cut vertically asshown.
Fig. K
43
Automatic Electric Blade Brake
Your saw is equipped with an automatic electric blade brake which stops the saw blade within
5 seconds of trigger release. This is not adjustable. On rare occasions the brake may not engage
and the blade will coast to a stop. If this occurs, wait for several minutes before continuing use.
9
ENGLISH
If the condition persists, there may be a fault condition. Have the tool serviced by an authorized
DeWALT servicecenter.
Always be sure the blade has stopped before raising the arm and removing the blade from the
kerf plate. The brake is not a substitute for guards. Ensure your own safety by giving the saw your
completeattention.
Guard Actuation and Visibility
CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle
when pulling the handle down. The lower guard will move up as the handle is pulled down
which could causepinching.
The blade guard on your saw has been designed to automatically raise when the arm is brought
down and to lower over the blade when the arm israised.
The guard can be raised by hand when installing or removing saw blades or for inspection of the
saw. NEVER RAISE THE BLADE GUARD MANUALLY UN LESS THE SAW IS TURNEDOFF.
NOTE: Certain special cuts of large material will require that you manually raise the guard. Refer
to Cutting Large Material under SpecialCuts.
The front section of the guard is louvered for visibility while cutting. Although the louvers
dramatically reduce flying debris, they are openings in the guard and safety glasses should be
worn at all times when viewing through thelouvers.
ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
Changing or Installing a New Saw Blade (Fig.A, L–N)
CAUTION:
Never depress the spindle lock button while the blade is under power orcoasting.
Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product
with this mitersaw.
Do not use abrasive wheels orblades.
Removing the Blade (Fig.L, M)
1. Remove the battery packs or powersupply.
2. Raise the arm to the upper position and raise the lower guard4 as far aspossible.
3. Loosen, but do not remove guard bracket screw43 until the guard bracket42 can be raised
far enough to access the blade screw44 (with integral washer). Lower guard will remain
raised due to the position of the guard bracketscrew.
4. Depress the spindle lock button45 while carefully rotating the saw blade by hand until the
lockengages.
5. Keeping the button depressed, use the other hand and the wrench provided25 to loosen
the blade screw44. (Turn clockwise, left-hand threads.)
6. Remove the blade screw44, outer blade washer46 and blade47. The inner blade
washer48, and if used, the 1" (25.4mm) blade adapter, may be left on thespindle.
NOTE: For blades with a blade hole of 5/8" (15.88 mm), the 1" (25.4 mm) blade adapteris
notused.
Installing a Blade (Fig.L–N)
1. Remove the battery packs or powersupply.
2. With the arm raised, the lower guard4 held open and the guard bracket42 raised, place
the blade on the spindle, onto the blade adapter (if using a blade with a 1" [25.4 mm]
diameter blade hole) and against the inner blade clamp with the teeth at the bottom of the
blade pointing toward the back of thesaw.
3. Assemble the outer clamp washer onto thespindle.
4. Install the blade screw44 (with integral washer) and, engaging the spindle lock, tighten the
screw firmly with wrench25 provided (turn counterclockwise, left-hand threads).
NOTE: When using blades with a 5/8" (15.88 mm) diameter blade hole, the blade adapter will
not be used and should be stored in a safe place for future use. The separate blade adapter is not
available on allmodels.
5. Return the guard bracket42 to its original position and firmly tighten the guard bracket
screw43 to hold bracket inplace.
WARNING: The guard bracket must be returned to its original position and the
guard bracket screw tightened before activating the saw. Failure to do so may
allow the guard to contact the spinning saw blade resulting in damage to the saw
and severe personalinjury.
25
4
43
44
42
Fig. L
45
Fig. M
Fig. N 46 47
48
44
Miter Scale Adjustment (Fig.G, O)
Unlock the miter lock lever6, press the miter release button7 and swing the miter arm until
it locks at the 0° miter position. Do not lock the miter lock lever. Place a square against the saw’s
fence and blade, as shown in FigureO. (Do not touch the tips of the blade teeth with the square.
To do so will cause an inaccurate measure ment.) If the saw blade is not exactly perpendicular
to the fence, loosen the four screws12 that hold the miter scale11 and move the miter lock
lever6 and the scale left or right until the blade is perpendicular to the fence, as measured with
the square. Retighten the four screws. Pay no attention to the reading of the miter pointer at
thistime.
10
ENGLISH
Fig. O
Miter Pointer Adjustment (Fig.G)
Unlock the miter lock lever6 to move the miter arm to the zero position. With the miter lock
lever unlocked, allow the miter arm to snap into place as you rotate the miter arm to zero.
Observe the miter pointer10 and miter scale11. If the pointer does not indicate exactly zero,
loosen the miter pointer screw holding the pointer in place, reposition the pointer and tighten
thescrew.
Miter Lock Adjustment (Fig.G, P)
The miter lock rod50 should be adjusted if the table of the saw can be moved when the miter
lock lever6 is locked (down). To adjust the miter lock, put the miter lock handle in the unlocked
(up) position. Using a 1/2" open end wrench, loosen the lock nut51 on the miter lock rod50.
Using a slotted screwdriver, tighten the miter lock rod by turning it clockwise. Turn the lock rod
until it is snug, then turn counterclockwise one turn. To ensure the miter lock is functioning
properly, re-lock the miter lock to a non-detented measurement on the miter scale – for example,
34º – and make sure the table will not rotate. Tighten locknut.
Fig. P
51
50
Bevel Square to Table Adjustment (Fig.A,I,Q)
To align the blade square to the table, lock the arm in the down position with the lock down
pin. Place a square against the blade, ensuring the square is not on top of a tooth. Loosen the
bevel lock knob6 and ensure the arm is firmly against the 0° bevel stop. Rotate the 0°bevel
adjustment screw36 Fig.I) with the 1/2" blade wrench as necessary so that the blade is at 0°
bevel to thetable.
Fig. Q
Bevel Pointers (Fig.I)
If the bevel pointer16 does not indicate zero, loosen the screw37 that holds it in place and
move the pointer as necessary. Ensure the 0° bevel is correct and the bevel pointers are set before
adjusting any other bevel anglescrews.
Bevel Stop 45º Right and Left Adjustment (Fig.H, I)
There are two bevel stop override levers, one on each side of thesaw.
To adjust the right 45° bevel angle, loosen the bevel lock knob26 and pull the 0° bevel override
lever29 to override the 0° bevel stop. When the saw is fully to the right, if the bevel pointer16
does not indicate exactly 45°, turn the left 45° bevel adjustment screw35 with the 1/2" blade
wrench until the bevel pointer indicates 45°.
To adjust the left 45° bevel angle, first loosen the bevel lock knob26 and tilt the head to the
left. If the bevel pointer16 does not indicate exactly 45°, turn the right 45° bevel adjustment
screw35 until the bevel pointer reads 45°.
Adjusting the Bevel Stop to 22.5° (or 33.9°) (Fig.H, I)
NOTE: Adjust the bevel angles only after performing the 0° bevel angle and bevel
pointeradjustment.
To set the left 22.5° bevel angle, flip out the left 22.5° bevel pawl32. Loosen the bevel lock
knob26 and tilt the head fully to the left. If the bevel pointer16 does not indicate exactly 22.5°,
turn the crown adjustment screw33 contacting the pawl with a 7/16" wrench until the bevel
pointer reads 22.5°.
To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl32. Loosen the bevel
lock knob26 and pull the 0° bevel override lever29 to override the 0° bevel stop. When the
saw is fully to the right, if the bevel pointer16 does not indicate exactly 22.5°, turn the crown
adjustment screw33 contacting the pawl with a 7/16" wrench until the bevel pointer indicates
exactly 22.5°.
Fence Adjustment (Fig.H)
In order that the saw can bevel to many bevel positions, one of the fences may have to be
adjusted to provide clearance. To adjust each fence, loosen the fence adjustment knob53 and
slide the fence14 outward. Make a dry run with the saw turned off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide max imum workpiece support,
without interfering with arm up and down movement. Tighten the fence adjustment knob
securely. When the bevel operations are complete, don’t forget to relocate thefence.
For certain cuts, it may be desirable to bring the fences closer to the blade. To use this feature,
back the fence adjustment knobs out two turns and move the fences closer to the blade past the
normal limit, then tighten the fence adjustment knobs to keep the fences in this location. When
using this feature, make a dry cut first to ensure the blade does not contact thefences.
NOTE: The tracks of the fences can become clogged with sawdust. If you notice that they are
becoming clogged, use a brush or some low pressure air to clear the guidegrooves.
Rail Guide Adjustment (Fig.A)
Periodically check the rails for any play or clearance. The right rail can be adjusted with the rail
adjustment screw23 shown in FigureA. To reduce clearance, use a 4 mm hex wrench and
rotate the rail adjustment screw clockwise gradually while sliding the saw head back and forth.
Reduce play while maintaining minimum slideforce.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
WARNING: Always use eye protection. All users and bystanders must wear eye
protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3).
WARNING: To ensure the blade path is clear of obstructions, always make a dry run
of the cut without power before making any cuts on theworkpiece.
WARNING: Install the table extensions to both sides of the saw's base. Refer to
Assembling the Table Extensionssection.
Installing and Removing the Battery Packs (Fig.R)
NOTE: For best results, make sure your battery packs are fullycharged.
To install the battery packs20 into the tool, align the battery packs with the rails on the side
of the motor housing and slide them in until they are firmly seated in the tool and ensure that
they do not disengage. Insert the dust cover59 into the corded power supply receptacle58 in
between thebatteries.
NOTICE: Keep the dust cover in place whenever the corded power supply is not
inuse.
To remove the battery packs from the tool, press the battery release button53 and firmly
pull the battery packs out. Insert them into the charger as described in the charger section of
thismanual.
11
ENGLISH
Fig. R
53
20
59
58
Installing and Removing the Corded Power Supply into and from
Tool (Fig.S–U)
Before inserting the corded power supply into your tool, remove the end of the dust cover59
from the tool's corded power supply receptacle58. Pull the dust cover away from the tool’s
corded power supply receptacle so that it does not interfere with insertion of the corded power
supply. Inspect the corded power supply receptacle for debris. Debris inside the receptacle
can prevent the corded power supply from fully seating. If debris is present, clean it using low
pressure air. Refer to Cleaning the Corded Power SupplyReceptacle.
NOTICE: The corded power supply is for AC power sources only when used with this
tool. Use with DC power sources could result in damage to thetool.
To install the corded power supply into your tool:
1. With the corded power supply unplugged, align its AC connector with the tool's corded
power supply receptacle58 then snap intoplace.
Fig. S
58
57
56
59
2. Ensure that it is fully seated in the tool and does notdisengage.
3. Attach the dust cover59 to the dust cover holder (60 Fig.T) in the corded powersupply.
4. Secure the cord clip56 into the tool's cord holder (55, Fig.U). Firmly press the clip into
theholder.
5. With the tool turned off, plug the corded power supply into a standard 120V household
electric power outlet. Do not attempt to use the corded power supply on any othervoltage.
6. Use the tool according to the tool instructions, making sure the cord is located so that it will
not be stepped on, tripped over, or otherwise subjected to damage orstress.
7. To remove the corded power supply from the tool, first unplug the corded power supply
from the outlet, then press the release button57 and firmly pull the corded power supply
out of the tool. Firmly press the end of the dust cover59 into the tool’s corded power supply
receptacle58.
Fig. W
PROPER CUT PROPER CUT
IMPROPER CUT IMPROPER CUT IMPROPER CUT
Fig. X
12
ENGLISH
Fig. U
Fig. T
60
56
55
Trigger Switch (Fig.V)
To turn the saw on, push the lock-off button3 to the left, then depress the trigger switch2.
The saw will run while the switch is depressed. Allow the blade to spin up to full operating speed
before making the cut. To turn the saw off, release the switch. Allow the blade to stop before
raising the saw head. There is no provision for locking the switch on. A hole45 is provided in the
trigger for insertion of a padlock to lock the switchoff.
Always be sure the blade has stopped before removing it from thekerf.
Fig. V
2
45
3
Body and Hand Position (Fig. W, X)
Proper positioning of your body and hands is crucial when operating the miter saw. Never place
hands inside the cutting area between the two red lines on the base while the blade is turning.
Clamp or hold the workpiece tightly to the table and the fence when cutting. Keep both hands
in position until the trigger has been released and the blade has completely stopped. ALWAYS
MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE PATH OF
THE BLADE. DO NOT CROSS HANDS, AS SHOWN IN FIGUREX.
Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm
left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard
louvers when following a pencilline.
Through-Cutting Operations
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
If the slide feature is not used, ensure the saw head is pushed back as far as possible and the rail
lock knob (22, Fig.A) is tightened. This will prevent the saw from sliding along its rails as the
workpiece isengaged.
NOTE: Although this saw will cut wood and many non-ferrous materials, we will limit our
detailed discussion to the cutting of wood only. The same guidelines apply to the other materials.
DO NOT CUT FERROUS (IRON AND STEEL) MAT ERIALS, MASONRY OR FIBER CEMENT WITH
THIS SAW. Do not use any abrasiveblades.
NOTE: Refer to Guard Actuation and Visibility in the Features and Controls section for
important information about the lower guard beforecutting.
Crosscuts (Fig. A, Y)
A crosscut is made by cutting wood across the grain at any angle. A straight crosscut is made
with the miter arm at the zero degree position. Set and lock the miter arm at zero, hold the wood
firmly on the table and against the fence. With the rail lock knob22 tightened, turn on the saw
by squeezing the trigger switch shown in FigureA.
When the saw comes up to speed (about 1 second) lower the arm smoothly and slowly to cut
through the wood. Let the blade come to a full stop before raisingarm.
Fig. Y
When cutting anything larger than a 2 x 8 (51 x 203mm [2 x 6 (51 x 152) at 45º miter]) use an
out-down-back motion with the rail lock knob22 loosened. Pull the saw out, toward you, lower
the saw head down toward the workpiece, and slowly push the saw back to complete the cut.
Do not allow the saw to contact the top of the workpiece while pulling out. The saw may run
toward you, possibly causing personal injury or damage to theworkpiece.
Cutting of multiple pieces is not recommended but can be done safely by ensuring that each
piece is held firmly against the table andfence.
NOTE: To provide greater crosscut capacity with reduced stroke, the blade on the saw extends
deeper into the table. As a result, a greater lifting force on the workpiece may be experienced
during thecut.
CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece
damage and personal injury, if your hands are required to be within 4" (100 mm) of the blade
during thecut.
NOTE: The rail lock knob22 shown in FigureA must be loose to allow the saw to slide along
itsrails.
Miter crosscuts are made with the miter arm at some angle other than zero. This angle is often
45º for making corners, but can be set anywhere from zero to 50º left or 60° right. Make the cut as
describedabove.
When performing a miter cut on workpieces wider than a 2 x 6 that are shorter in length, always
place the longer side against thefence.
To cut through an existing pencil line on a piece of wood, match the angle as close as possible.
Cut the wood a little too long and measure from the pencil line to the cut edge to determine
which direction to adjust the miter angle and recut. This will take some practice, but it is a
commonly usedtechnique.
Bevel Cuts
A bevel cut is a crosscut made with the saw blade leaning at an angle to the wood. In order to
set the bevel, loosen the bevel lock (26, Fig.A), and move the saw to the left or right as desired.
(It is necessary to move the fence to allow clearance.) Once the desired bevel angle has been set,
tighten the bevel lock firmly. Refer to the Features and Controls section for detailed instructions
on the bevelsystem.
Bevel angles can be set from 49º right to 49º left and can be cut with the miter arm set between
50º left or 60º right. At some extreme angles, the right or left side fence might have to be
removed. To remove the left or right fence, unscrew the fence adjustment knob several turns and
slide the fenceout.
NOTE: Refer to Fence Adjustment in the Adjustments section for important information on
adjusting the fences for certain bevelcuts.
Quality of Cut
The smoothness of any cut depends on a number of variables. Things like material being cut,
blade type, blade sharpness and rate of cut all contribute to the quality of thecut.
When smoothest cuts are desired for molding and other precision work, a sharp (60 tooth
carbide) blade and a slower, even cutting rate will produce the desiredresults.
Ensure that the material does not move or creep while cutting; clamp it securely in place. Always
let the blade come to a full stop before raisingarm.
If small fibers of wood still split out at the rear of the workpiece, stick a piece of masking tape
on the wood where the cut will be made. Saw through the tape and carefully remove tape
whenfinished.
For varied cutting applications, refer to the list of recommended saw blades for your saw and
select the one that best fits your needs. Refer to Saw Blades underAccessories.
13
ENGLISH
Non-Through-Cutting (Grooving and Rabbeting)
Instructions in the Crosscuts, Bevel Cuts and Cutting Compound Miters sections are for cuts
made through the full thickness of the material. The saw can also perform non-through cuts to
form grooves or rabbets in thematerial.
Groove Cut (Fig. A)
Refer to Depth Stop for detailed instructions for setting Hold the wood firmly on the table
and against the fence14 . Align the cut area underneath the blade. Position the saw arm fully
forward, with blade in down position. Turn on the saw by squeezing the trigger switch2 shown
in FigureA. Smoothly, push saw arm rearward to cut a groove through the workpiece.
Release the trigger switch with the saw arm down. When saw blade has completely stopped,
raise the saw arm. Always let the blade come to a full stop before raising thearm.
To widen the groove, repeat steps 1–4 until the desired width isobtained.
Clamping the Workpiece
WARNING: A workpiece that is clamped, balanced and secure before a cut may become
unbalanced after a cut is completed. An unbalanced load may tip the saw or anything the
saw is attached to, such as a table or workbench. When making a cut that may become
unbalanced, properly support the workpiece and ensure the saw is firmly bolted to a stable
surface. Personal injury mayoccur.
WARNING: The clamp foot must remain clamped above the base of the saw whenever the
clamp is used. Always clamp the workpiece to the base of the saw – not to any other part of
the work area. Ensure the clamp foot is not clamped on the edge of the base of thesaw.
CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece
damage and personal injury, if your hands are required to be within 4" (100mm) of the blade
during thecut.
If you cannot secure the workpiece on the table and against the fence by hand (irregular shape,
etc.), or your hand would be less than 4" (100 mm) from the blade, a clamp or other fixture must
beused.
Use the material clamp provided with your saw. To purchase the material clamp, contact your
local retailer or DeWALT servicecenter.
Other aids such as spring clamps, bar clamps or C-clamps may be appropriate for certain sizes
and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry
run before making the cut. The left or right fence will slide from side to side to aid inclamping.
To Install Clamp
1. Insert it into the hole (27, Fig.A) behind the fence. The clamp should be facing toward the
back of the miter saw. The groove on the clamp rod should be fully inserted into the base.
Ensure this groove is fully inserted into the base of the miter saw. If the groove is visible, the
clamp will not besecure.
2. Rotate the clamp 180º toward the front of the mitersaw.
3. Loosen the knob to adjust the clamp up or down, then use the fine adjust knob to firmly
clamp theworkpiece.
NOTE: Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE DRY
RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE THE
CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW ORGUARDS.
Support for Long Pieces
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
ALWAYS SUPPORT LONGPIECES.
Never use another person as a substitute for a table extension, as additional support for a
workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull
theworkpiece.
For best results, use the DW7080 extension work support to extend the table width of your saw,
available from your dealer at extra cost. Support long workpieces using any convenient means
such as sawhorses or similar devices to keep the ends fromdropping.
Cutting Picture Frames, Shadow Boxes And Other Four-Sided
Projects (Fig.Z,AA)
To best understand how to make the items listed here, we suggest that you try a few simple
projects using scrap wood until you develop a “feel” for yoursaw.
Your saw is the perfect tool for mitering corners like the one shown in FigureZ. Sketch 1 in
FigureAA shows a joint made by using the bevel adjustment to bevel the edges of the two
boards at 45º each to produce a 90º corner. For this joint the miter arm was locked in the zero
position and the bevel adjustment was locked at 45º. The wood was positioned with the broad
flat side against the table and the narrow edge against the fence. The cut could also be made by
mitering right and left with the broad surface against thefence.
Fig. Z
1
Fig. AA
1
2
Cutting Trim Molding And Other Frames (Fig.AA)
Sketch 2 in FigureAA shows a joint made by setting the miter arm at 45º to miter the two boards
to form a 90º corner. To make this type of joint, set the bevel adjustment to zero and the miter
arm to 45º. Once again, position the wood with the broad flat side on the table and the narrow
edge against thefence.
The two sketches in FigureAA are for four-sided objectsonly.
As the number of sides changes, so do the miter and bevel angles. The chart below gives the
proper angles for a variety ofshapes.
– EXAMPLES –
NUMBER OF SIDES MITER OR BEVEL ANGLE
4 45°
5 36°
6 30°
7 25.7°
8 22.5°
9 20°
10 18°
The chart assumes that all sides are of equal length. For a shape that is not shown in the chart,
use the following formula: 180º divided by the number of sides equals the miter (if the material is
cut vertically) or bevel angle (if the material is cut laying flat).
Cutting Compound Miters (Fig.BB)
A compound miter is a cut made using a miter angle and a bevel angle at the same time. This is
the type of cut used to make frames or boxes with slanting sides like the one shown in FigureBB.
NOTE: If the cutting angle varies from cut to cut, check that the bevel lock knob and the miter
lock handle are securely locked. These must be locked after making any changes in bevel
ormiter.
The chart at the end of this manual (Table 1) will assist you in selecting the proper bevel and
miter settings for common compound miter cuts. To use the chart, select the desired angleA
(Fig.BB) of your project and locate that angle on the appropriate arc in the chart. From that point
follow the chart straight down to find the correct bevel angle and straight across to find the
correct miterangle.
Fig. BB
Angle “A”
Set your saw to the prescribed angles and make a few trial cuts. Practice fitting the cut pieces
together until you develop a feel for this procedure and feel comfortable withit.
Example: To make a 4-sided box with 26º exterior angles (Angle A, Fig.BB), use the upper right
arc. Find 26° on the arc scale. Follow the horizontal intersecting line to either side to get miter
angle setting on saw (42°). Likewise, follow the vertical intersecting line to the top or bottom to
get the bevel angle setting on the saw (18°). Always try cuts on a few scrap pieces of wood to
verify the settings on thesaw.
Cutting Base Molding (Fig.K, CC)
ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANYCUTS.
Straight 90º cuts:
Position the wood against the fence and hold it in place as shown in FigureCC. Turn on the saw,
allow the blade to reach full speed and lower the arm smoothly through thecut.
Cutting Base Molding from 3" UP TO 6.75" (76 mm to 171 mm) High Vertically Against
the Fence
NOTE: Use the slide lock lever43, shown in FigureK, when cutting base molding measuring
from 3" to 6.75" (76 mm to 171 mm) high vertically against thefence.
Position material as shown in FigureCC.
14
ENGLISH
Fig. CC
All cuts should be made with the back of the molding against the fence and with the bottom of
the molding against thetable.
INSIDE CORNER OUTSIDE CORNER
Left side Miter left 45°
Save left side of cut
Miter right 45°
Save left side of cut
Right side Miter right 45°
Save right side of cut
Miter left 45°
Save right side of cut
Material up to 6.75" (171 mm) can be cut as describedabove.
Cutting Crown Molding
Your miter saw is well suited to the task of cutting crown molding. In order to fit properly, crown
molding must be compound mitered with extremeaccuracy.
The two flat surfaces on a given piece of crown molding are at angles that, when added together,
equal exactly 90º. Most, but not all, crown molding has a top rear angle (the section that fits flat
against the ceiling) of 52º and a bottom rear angle (the part that fits flat against the wall) of38º.
Your miter saw has special pre-set miter latch points at 31.62º left and right for cutting crown
molding at the proper angle and bevel stop pawls at 33.9º left and right. There is also a mark on
the bevel scale at 33.9º.
The chart below gives the proper settings for cutting crown molding. (The numbers for the miter
and bevel settings are very precise and are not easy to accurately set on your saw.) Since most
rooms do not have angles of precisely 90º, you will have to fine tune your settingsanyway.
PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!
Instructions for Cutting Crown Molding Laying Flat and Using
the Compound Features (Fig. DD)
1. Molding should lay flat with broad back surface down on sawtable.
2. Top of molding againstfence.
3. The settings below are for all standard (U.S.) crown molding with 52° and 38°angles.
INSIDE CORNER OUTSIDE CORNER
Left side
Bevel left 33.9°
Miter table set at right 31.62°
Save left end of cut
Bevel right 33.9°
Miter table set at left 31.62°
Save left end of cut
Right side
Bevel right 33.9°
Miter table set at left 31.62°
Save right end of cut
Bevel left 33.9°
Miter table set at right 31.62°
Save right end of cut
When setting bevel and miter angles for all compound miters, remember that:
The angles presented for crown moldings are very precise and difficult to set exactly. Since they
can easily shift slightly and very few rooms have exactly square corners, all settings should be
tested on scrapmolding.
Fig. DD
Fence
Table
Crown molding flat on table and against fence
PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!
Alternative Method for Cutting Crown Molding (Fig. EE)
Place the molding on the table at an angle between the fence and the saw table, as shown in
FigureEE. Use of the crown molding fence accessory (DW7084) is highly recommended because
of its degree of accuracy and convenience (Refer to Optional Accessories). The crown molding
fence accessory is available for purchase from your localdealer.
The advantage to cutting crown molding using this method is that no bevel cut is required.
Minute changes in the miter angle can be made without affecting the bevel angle. This way,
when corners other than 90º are encountered, the saw can be quickly and easily adjusted for
them. Use the crown molding fence accessory to maintain the angle at which the molding will
be on thewall.
Instructions for Cutting Crown Molding Angled Between the
Fence and Base of the Saw For All Cuts
1. Angle the molding so the bottom of the molding (part which goes against the wall when
installed) is against the fence and the top of the molding is resting on the saw table, as
shown in FigureEE.
2. The angled “flats” on the back of the molding must rest squarely on the fence and sawtable.
INSIDE CORNER OUTSIDE CORNER
Left side Miter right at 45°
Save right side of cut
Miter left at 45°
Save right side of cut
Right side Miter left at 45°
Save left side of cut
Miter right at 45°
Save left side of cut
Crown Molding Between Fence and Table
Table
Fence
Bottom side
of molding
Top side
of molding
Fig. EE
DW7084 Crown
Molding Fence
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST
THEFENCE.
Aluminum Cutting (Fig. FF, GG)
ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM. These
are available at your local DeWALT retailer or DeWALT service center. Certain workpieces, due to
their size, shape or surface finish, may require the use of a clamp or fixture to prevent movement
during the cut. Position the material so that you will be cutting the thinnest cross section, as
shown in FigureFF. FigureGG illustrates the wrong way to cut theseextrusions.
Use a stick wax cutting lubricant when cutting aluminum. Apply the stick wax cutting lubricant
directly to the saw blade before cutting. Never apply stick wax to a moving blade. The wax,
available at most hardware stores and industrial mill supply houses, provides proper lubrication
and keeps chips from adhering to theblade.
Be sure to properly secureworkpiece.
Refer to Saw Blades under Optional Accessories for correct sawblade.
15
ENGLISH
Fig. FF
Blade
CORRECT
Fence
INCORRECT
Fig. GG
Blade
Fence
Bowed Material (Fig. HH, II)
When cutting bowed material always position it as shown in Figure HH and never like that
shown in Figure II. Positioning the material incorrectly will cause it to pinch the blade near the
completion of thecut.
Fig. HH
CORRECT
Fig. II
INCORRECT
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be cut just like wood and CLAMPED OR
HELD FIRMLY TO THE FENCE TO KEEP IT FROM ROLLING. This is extremely important when
making anglecuts.
Cutting Large Material (Fig. JJ)
Occasionally you will encounter a piece of wood a little too large to fit beneath the lower guard.
If this occurs, simply place your right thumb on the upper side of the guard and roll the guard up
just enough to clear the workpiece, as shown in Figure JJ. Avoid doing this as much as possible,
but if need be, the saw will operate properly and make the bigger cut. NEVER TIE, TAPE, OR
OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING THISSAW.
Fig. JJ
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An accidental
start-up can causeinjury.
WARNING: To reduce the risk of serious personal injury, DO NOT touch the sharp
points on the blade with fingers or hands while performing anymaintenance.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.
All bearings are sealed. They are lubricated for life and need no furthermaintenance.
Periodically clean all dust and wood chips from around AND UNDER the base and the
rotary table. Even though slots are provided to allow debris to pass through, some dust
willaccumulate.
Removing and Replacing Belt (Fig.A, KK)
The belt is designed to last the life of the tool. However, abuse of the tool could cause the belt
tofail.
If the blade does not turn when the motor is running, the belt has failed. To inspect or replace
the belt, remove the belt cover screws. Remove the belt cover. Inspect the ribs of the belt for
wear or failure. Check belt tension by squeezing the belt. The belt halves should almost touch
when squeezing firmly with the thumb and index finger. To adjust the tension, loosen, but do not
remove, the four crosshead screws62. Then rotate the set screw63 on the top of the motor
plate casting until the proper tension is achieved. Tighten the four screws securely and replace
the beltcover.
NOTICE: Overtightening the belt will cause premature motorfailure.
Fig. KK
62 63
Cleaning
WARNING: Blow dirt and dust out of all air vents and guard mechanisms (if applicable) with
clean, dry air at least once a week. To minimize the risk of eye injury, always wear approved
eye protection and respiratory protection when performingthisprocedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into aliquid.
16
ENGLISH
Cleaning the DeWALT Corded Power Supply
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into aliquid.
Cleaning the Corded Power Supply Receptacle (Fig. S)
WARNING: Blow debris out of the corded power supply receptacle58 with clean, dry air.
To minimize the risk of eye injury, always wear approved eye protection and respiratory
protection when performingthis.
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent dust
from flowing away from the cutting area properly. With the battery pack or corded power supply
removed and the saw head raised fully, low pressure air or a large diameter dowel rod can be
used to clear the dust out of the dustduct.
CUTLINE™ LED Worklight Cleaning
For the best worklight performance, perform the following maintenance regularly with the
battery or corded power supplyremoved.
Carefully clean sawdust and debris from worklight lens with a cottonswab.
DO NOT use solvents of any kind, they may damage thelens.
Dust build-up can block the worklight and prevent it from accurately indicating the line
ofcut.
Follow miter saw’s instruction manual to remove and installblade.
With blade removed from saw, clean pitch and build-up from blade. Pitch and debris can
interfere with the worklight and prevent it from accurately indicating the line ofcut.
Accessories
WARNING: Since accessories, other than those offered by DeWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only DeWALT recommended accessories should be used with thisproduct.
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center.
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other locally
obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in
selecting and usingaccessories.
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precisioncutting.
Dust Bag: DW7053
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdustproduced.
Crown Molding Fence: DW7084
Used for precision cutting of crownmolding.
SAW BLADES: ALWAYS USE 12" (305 mm) SAW BLADES WITH EITHER 1" (25.4 mm) OR 5/8"
(15.88 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 4800 RPM. Never use a smaller
diameter blade. It will not be guarded properly. Use crosscut blades only! Do not use blades
designed for ripping, combination blades or blades with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (maximum thin kerf with anti-stick rim)
General Purpose 12" (305 mm) 40
Fine Crosscuts 12" (305 mm) 60
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 12" (305 mm) 80
Non-ferrous metals 12" (305 mm) 96
NOTE: For cutting non-ferrous metals, use only saw blades with TCG (Triple Chip
Grind) teeth designed for thispurpose.
17
ENGLISH
10
10
10
20
20
20
30
30
30
40
40
40
50
50
50
60
60
60
70
70
70
80
80
80
TABLE 1: COMPOUND MITER CUT
(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
SET THIS MITER ANGLE ON SAW
SQUARE BOX
6-SIDED BOX
SET THIS BEVEL ANGLE ON SAW
8-SIDED BOX
ANGLE OF SIDE OF BOX (ANGLE A)
18
繁體中文
1
󶍘󹠔󰶦󳛓
󷵫 󱟈󼵱
󷰟󸼘󷶢󳄿󳥥󲔟󽤤󷵫󱟈󱛼󳄿󳥥󳉹󵤛󽴸󰵷󸗿󲳆󸔐󰹊󷵫󱟈󱛼
󷯟 󳟉 󱜴 󶡌 󳥛 󲘭 󶩟 󷩹 󹄷󽴷󴦢 󴧆 󱛼 󳃵 󱯃 󸡿 󱇋 󲕴󽴸
󷵫 󱟈󼶊󴩁󰸬󸿯󰽝󱜍󱇋󵒹󹐑󹂗󽴺󲳴󹌮󰺬󶄤󸼘󷶢󰾫󵈾󳅜󱍂󽴸
󷰟󰿝󱜶󴦔󶍘󹠔󰶦󳛓󷯟󳟉󳥆󵒹󱌊󲖃󴩁󰶻󽴸
󴎥 󲼒󼶊
60V Max
󴩁󳥔󱿑󱐳󲄦󹄷󴋓󹄷󱼻
 󴬃 󷼿 󸋻 󴖡 󸢁 󽴺󳺧 󵫗 󹄷
󱼻󴩁
54V
󽴸
1 󳕾󰽳󳅜󳪒
2 󷩹󵒯󸻛󸽡
3 󷩹󵒯󸯴󴃻󳉿󸤉
4 󰵵󸛉󸿉󷶍󶔠
5 󲔟󷡥󲒱
6 󳛸󷨭󸯴󲕂󳮾
7 󳛸󷨭󸡽󳙟󳉿󸤉
8 󳛸󷨭󸯴󸨽󸡿󵋖󳮾
9 󸫀󶌨󲪃󶩪
10 󳛸󳍻󱑡󲫟󲙰󳉹󸢛
11 󳛸󳍻󱑡󲫟󲙰
12 󳛸󳍻󱑡󲫟󲙰󷙡󶆤
13 󲫂󲫡󲮃󸻁󳮾
14 󳕻󳨣
15 󳛸󹈘󱑡󲫟󲙰
16 󳛸󹈘󱑡󲫟󲙰󳉹󸢛
17 󸯴󲕂󸨽
18 󳏀󶪋󳅜󳪒
19 CUTLINE󲦩󰽳󴱛󸻛󸽡
20 󹄷󴋓󶅊
21 󲘭󸊩
22 󲘭󸊩󸯴󲕂󳝓󸤉
23 󲘭󸊩󷰆󳚯󷙡󶆤
24 󳍗󱺕󱜢
25 󱌚󷨭󳆙󳅜
26 󳛸󹈘󸯴󲕂󳝓󸤉
27 󶉞󱱀󲒱
28 󳅜󳪒󱏿󳹶
󱱭 A
4
5
15
16
17
514
13 101112
58 679
28
󲕂 󶖐󼶊󲔟 󽤤 󷵫 󵤛 󵳙 󷐬 󶪆 󵈾 󷭃
󳦦󰾫󵈾󳅜󱍂󰾫󵈾󰻄󰵵󲔟󽤤󷵫󵤛󵳙󷐬󶪆󵈾󷭃󽴺󷷋󲹢󴎥󲼒󱙮󹂗󴸝󴍤󰻄󱛼󰺄󸉩󱇋󲕴󳃵󷽀󵈵󳐧󱿠󵒹󹐑󹂗󽴸
󱙮 󹂗󼶊󷞎󵤛󶉞󲶋󱙮󹂗󴸝󴍤󽴺󶱱󳦣󶡌󸘛󱋞󽴺󲘠󲘭󶩟󴄧󰹘󳃵󱯃󸡿󱇋󲕴󽴸
󷵫 󱟈󼶊󷞎󵤛󴞵󱲉󱙮󹂗󲺖󴍤󽴺󶱱󳦣󶡌󸘛󱋞󽴺󱜴󶡌󲘭󶩟󴄧󰹘󳃵󱯃󸡿󱇋󲕴󽴸
󲘮 󲳲󼶊󷞎󵤛󴞵󱲉󱙮󹂗󲺖󴍤󽴺󶱱󳦣󶡌󸘛󱋞󽴺󱜴󶡌󲘭󶩟󸌌󲳐󳃵󰶦󲫟󱇋󲕴󽴸
󽵈󱇧󳥥󳺧󵤛󵳙󷐬󳠙󼵹󷞎󵤛󲔟󽤤󵕲󸽡󷪞󲸃󽴸
󴎥 󲼒󼶊󷞎󵤛󰵨󵫐󹈍󰺄󸉩󱇋󲕴󵒹 󷝥 󴩁󽴺󶱱󳦣 󶡌 󸘛 󱋞󽴺󱜴󶡌󲘭󶩟󷽀󵈵󳐧󱿠󽴸
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

DeWalt DHS790N ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で