Tycon Power TP-SW8GAT/BT/24-SFP ユーザーマニュアル

カテゴリー
ネットワークスイッチ
タイプ
ユーザーマニュアル
Gigabit Industry Managed PoE Switch
8000110 Ver 5.0.8
WEB Management Manual
1
Statement
All rights reserved
or all of the contents of this manual, and it is not allowed to spread in any form
The copyright of this manual belongs to Tycon Systems. Without the written
permission of Tycon Systems, no unit or individual is allowed to extract or copy part
2
Preface
This manual mainly describes the web page of industrial grade full Gigabit
management PoE switch. Users can manage the switch through the web page of full
Gigabit management PoE switch. This manual only briefly introduces the operation of
each web page. Please refer to the user's operation manual for the introduction of each
function of the full Gigabit management Ethernet switch
The preface includes the following contents
Readers
Product
Product function
Readers
Network planners
On site technical support and maintenance person
Network administrator responsible for network configuration and maintenance
Product
All Gigabit management Ethernet switch is designed and developed by our company.
It is specially designed for the construction of high security and high performance
network. The system adopts a new software and hardware platform, provides a
comprehensive security protection system, perfect QoS strategy and rich VLAN
functions, and has simple management and maintenance. It is an ideal convergence
layer switch for office network, campus network, small and medium-sized enterprises
and branches
Product features
Support IEEE 802.3x
3
Support IEEE 802.3IEEE 802.3uIEEE 802.3abIEEE 802.3z
Support IEEE 802.3ad
Support IEEE 802.3q IEEE 802.3q/p
Support IEEE 802.1wIEEE 802.1d EEE 802.1S
Support 16K MAC address table, automatic update, two-way learning
Support port based VLAN, up to 4096 VLAN
Support 802.1Q standard VLAN
Support STP Spanning tree protocol
Support RSTP Fast spanning tree protocol
Support MSTP Fast spanning tree protocol
Support EPPS Ring network protocol
Support EAPS Ring network protocol
Support 802.1x Argumentation agreement
Support 8 groups of aggregation, each group supports up to 8 ports
Support bidirectional port image
Support loop protection function, real-time detection, rapid alarm, accurate
positioning, intelligent blocking and automatic recovery
Support the isolation of downlink ports and communication with uplink ports
Support half duplex control based on back pressure
Support full duplex based on pause frame
Support port based input / output bandwidth management
Support IGMPv1/2/3 MLDv1/2 Snooping
Support GMRP Agreement Registration
Support multicast address management, multicast VLAN, multicast routing port
and static multicast address
Support DHCP Snoping
Support storm suppression of unknown unicast, multicast, unknown multicast and
broadcast type
4
Support storm suppression based on bandwidth adjustment and storm filtering
Support user port + IP address + MAC address
Support ACL based on IP and MAC
Support the security nature of the number of MAC addresses based on the port
Support 802.1p port queue priority algorithm
Support CoS / TOS, QoS tag
Support WRR (Weighted Round Robin)Weighted priority rotation algorithm
It supports WRR, SP and WFQ priority scheduling modes
Support auto mdix function, automatically identify through network cable and
cross network cable
Support port support automatic negotiation function (self negotiation transmission
rate and duplex mode)
Support upgrade package upload
Support system log viewing
Support web to restore factory configuration
Support to open or close the port
Support standard Poe scheduling management
Support the function of automatic detection online equipment (automatic, no
operation)
Support web interface management
Support cli management based on telnet and console
Support SNMP V1/V2/V3 management
Support SSHV1/V2 management
Support RMON management
[Version update]
Ver 5.0.8
User experience Optimization
5
It solves the known problems and has faster response speed
Perfect support for Chinese English one click conversion
Optimize the related functions to make the management easier
Catalog
一、WEB PAGE OVERVIEW .............................................................................................................. 6
1WEB Characteristics of the visit .......................................... 6
2WEB System requirements for browsing .................................. 6
3WEB Login of browsing session ......................................... 7
4WEB Basic composition of the page ...................................... 8
5Navigation tree structure ................................................ 8
6Page button introduction ................................................ 9
7Error message ........................................................ 9
8Entry field ............................................................ 10
9State domain ......................................................... 10
二、WEB PAGE INTRODUCTION ..................................................................................................... 11
1Login Dialog ......................................................... 11
1Login Dialog ......................................................... 11
2Main page ........................................................... 12
3System configuration .................................................. 13
4Port configuration ..................................................... 13
5MAC binding ......................................................... 31
6MACfilter ............................................................ 33
7VLAN
configuration ................................................... 34
8SNMP
configuration .................................................. 36
9ACL
configuration .................................................... 38
10Qos
configuration ................................................... 43
11IP basic
configuration ................................................ 44
12AAA
configuration ................................................... 46
13MSTP
configuration ................................................. 50
14IGMPSNOOPING
configuration ....................................... 52
15GMRP
configuration ................................................. 53
16EAPS
configuration .................................................. 54
17RMON
configuration ................................................. 56
18Cluster management ................................................. 58
19ERPS
configuration.................................................. 61
20Log management .................................................... 62
21POE port
configuration ............................................... 63
6
一、WEB Page overview
1WEB Characteristics of the visit
All Gigabit management Ethernet switch provides users with web access function. Users
can access the switch through web browser to manage and configure the switchThe main
features of the visit are
Easy access: users can easily access the switch from anywhere in the network
Users can use familiar Netscape communicator, Microsoft Internet Explorer and other
browsers to access the web page of full Gigabit management Ethernet switch, and the
web page is presented to users in graphical and tabular form
Gigabit management Ethernet switch provides rich web pages, through which users
can configure and manage most of the functions of the switch
The classification and integration of web page functions is convenient for users to find
relevant pages for configuration and management
2System requirements of WEB browsing
The system requirements of web browsing are shown in Table 1
Table1
Hardware
and
Software
System requirements
CPU
Pentium 586 up
Memory
128MB up
Resolution
ratio
800x600 up
Color
256 color up
Browser
IE4.0 or above or Netscape 4.01 or above
system
Windows2000®,WindowsXP®,WindowsME®, WindowsVista®,
Windows7®, Windows8®,MAC, Linux,Unix operating system
Tips
®,Windows ME®, WindowsVista®, Windows7®, Windows8® is a registered trademark of
Microsoft Corporation. All other product names, trademarks, registered trademarks and
service marks are copyrighted by their respective owners.
Operating Microsoft® ,Windows95®,Windows10®,WindowsNT®,
Microsoft®,Windows95®,Windows10®,WindowsNT®,Windows2000®,WindowsXP
7
3Login of web browsing session
The user needs to confirm before starting a web browsing session
The switch has been configured with IP. By default, the vlan1 interface IP address of
the switch is 192.168.0.1
The subnet mask is 255.255.255.0
A host with a web browser has been connected to the network, and the host can ping
the switch
After completing the above two tasks, the user can enter the address of the switch in
the address bar of the browser and press enter to enter the web login page of the
switch, as shown in Figure 1. When multi-user management is not enabled, users
web. Only when they enter the correct password can they access the web. The
If multi-user management is enabled and privileged users are configured in the system, the
password of anonymous users will not take effect. Users do not verify the password of
anonymous users when accessing the web, but verify the user name and password of
multi-user management
Figure 1 login page of web browsing session
password of the anonymous user is admin by default
need to verify the password of the anonymous user (admin) when they log on to the
8
4Basic composition of WEB page
As shown in Figure 2, the web page is mainly composed of three parts: the title page, the
navigation tree page and the main page
Figure 2 basic composition page of switch web page
Title Page The logo and real-time port status are shown in the following figure
The green light indicates that the port is connected;
The gray light indicates that the port is not connected;
The red light indicates that the port is closed (refer to figure 17 for specific settings)
Main page Used to display the page selected by the user from the navigation tree
5Navigation tree structure
Figure 3 shows the organizational structure of the navigation tree
The navigation tree is located at the bottom left of each page, and the nodes of the web
page are displayed in the form of tree. Users can easily find the web page to manage.
According to the different functions of the web page, it is divided into different groups, each
group includes one or more pages. Most of the page names in the navigation tree are the
abbreviations of the page title at the top of the corresponding page
9
Figure 3 organization page of switch navigation tree
6Page button introduction
There are some general buttons on the page, and the functions of these buttons are
generally the same. Table 2 introduces the functions of these buttons
Table 2
Button
Function
Refresh
Update all fields on the page
Application
Put the updated value into memory. Because error checking is
done by the web server,So there is no error checking before
the user selects the button
Delete
Delete current record
Help
Open the help page to view the configuration description of
each page
7Error message
If the web server of the switch makes an error when processing the user's request, the
corresponding error information will be displayed in a dialog box. For example, figure 4 shows
an error message dialog
4 出错信息页面
10
8Entry field
Some pages have an entry field in the leftmost column of the table, as shown in Figure 5,
through which different rows in the table can be accessed. When you select a value in the
entry field, the corresponding information of that line will be displayed in the first line. At this
time, only that line can be edited, which is also called the active line. When a page is initially
loaded, the entry field displays new and the activity behavior is empty
If you want to add a new line, select new from the drop-down menu in the entry field, enter
the new line information, and then press the apply key
If you want to edit an existing row, select the corresponding row number from the
drop-down menu of the entry field, edit the row as needed, and then press the apply key. You
will see the corresponding changes displayed in the table
If you want to delete a row, select the corresponding row number from the drop-down
menu of the entry field, and then press the delete key, and the row will disappear from the
table
Figure 5 entry field page
9State domain
Some pages have a status field in the rightmost column of the table, as shown in Figure 6,
which displays the status of the row. The state field is read-only because all changes to the
row state are processed internally. Once all the domain information in a row is valid, the state
of the row will automatically become active
11
Figure 6 state field page
二、WEBPage introduction
1Login Dialog
Figure 1-1 login page of web browsing session
Figure 7 shows the login dialog box, which is displayed when the user logs in to the web
page for the first time. The user can enter the user name and password in the corresponding
field, and then click OK to log in to the web server of the switch. Passwords are case sensitive,
anonymous user passwords can be set up to 16 characters, while multiple user names and
12
passwords can be set up to 16 characters. The default user name of the management switch
is the anonymous user name admin, the default password is the anonymous user password,
and the anonymous user password is empty by default
2Main page
Figure 1-2 shows the web main page of the management switch. The page will be
displayed after the user logs in to the web page
Figure 1-2 main page of switch
13
3Industrial switch monitoring
platform
Alarm detection mode
1.1 Off: the alarm is in off state, no alarm state output and action
1.2 Low level alarm: when the alarm input changes from high level to low level, the alarm
will be triggered. (higher than 5V, lower than 57V is high level, lower than 5V is low level)
1.3 High level alarm: when the alarm input changes from low level to high level, the alarm will be
triggered. (higher than 5V, lower than 57V is high level, lower than 5V is low level)
2Close port
2.1 Select port: select the port to be activated after the alarm is triggered. After the alarm is
released, the port action will return to the open state. For each trigger, select the port to restart
once, and do not repeat
2.2 Status box: alarm /
normal
14
3Restart port
3.1 Select port: select the port to be activated after the alarm is triggered. The port performs
the port restart action once. For each trigger, select the port restart once and do not repeat
3.2 Status box: alarm /
normal
Alarm output configuration
1. Alarm output mode
1.1 Turn off alarm: the alarm output is in the off state, and there is no alarm state output
and action
1.2 Alarm (normally closed): after the alarm is triggered, the alarm output is combined
1.3 Alarm (normally open): after triggering the alarm, the alarm output is open
1.4 Cycle alarm: after the alarm is triggered, the alarm output will open / close
cycle
15
2). Port failure
2.1 Select port
2.11Data port: select the monitoring data port status. When the status is invalid, the alarm
output will be triggered. When the status is normal, the alarm will be released
2.12PoE port: select the POE state of monitoring data. When the state fails, the alarm output
will be triggered. When the state is normal, the alarm will be released
3). Execution action
3.1 Status bar: failure alarm port display /
normal
4). System condition failure
4.1 System temperature: that is, the temperature in the chassis. Set a temperature value, and if
it exceeds this range, an alarm will be triggered
4.2 Ambient temperature: set a temperature value. If the temperature exceeds this range, an
alarm will be triggered. The sensor needs to be selected
4.3 Environment humidity: set a humidity value. If it exceeds this range, an alarm will be
triggered. Sensor is required
4.4 System power overload: set a power value, exceeding this range will trigger an alarm
16
4.5 V1 voltage of main power supply: trigger alarm through system monitoring judgment
4.6 V2 voltage from power supply: trigger alarm through system monitoring judgment
4.7 System 3.3V: the alarm will be triggered if it exceeds the system monitoring judgment
4.8 System 1.5V: the alarm will be triggered if it exceeds the system monitoring judgment
4.9 System 1.2V: the alarm is triggered by exceeding the system monitoring judgment
4.10 Alarm input: the alarm is triggered by the effective state of the alarm input, and the
alarm input function needs to be
enabled
5). Execution action
5.1 Status bar: failure alarm port display /
normal
4System configuration
Language switch: switch between Chinese and English system interface easily through
the language switch button in the upper right corner
1Basic information
17
Figure 4-1 is the basic information configuration page, through which users can configure
the basic information of the switch
System description displays the description of system related parameters
The system descriptor identification number shows the identification of the system in the
network management
The system version number shows the version number of the software currently used by
the switch
The number of network interfaces shows the current number of network interfaces in the
switch
The system startup time shows the time from the switch startup to the present
The system clock displays the current clock of the system. The user can modify the
current clock of the system and input the parameters of year, month, day, hour, minute
and second
The system name shows the system name of the switch in the network. Users can modify
the system name
The system location shows the physical location of the switch in the network, and the user
can modify the system location
The system contact display manages the contact person and contact information of the
current node, and the user can modify the system contact information
Figure 4-1 basic information page
2Serial port information
Figure 4-2 shows the serial port configuration page, which displays the serial port baud
rate and other information related to the serial port. When the host manages the switch
through the serial terminal (such as the super terminal of windows), the COM port
configuration on the serial terminal must be consistent with the information on this page
18
Figure 4-2 serial port information page
3user management
Figure 4-3 is the user management page. Through this page, users can modify the
password of the switch's anonymous user (admin). Telnet and web use the same anonymous
user password when multiple users are not enabled. Passwords are case sensitive and can be
set up to 16 characters. If you want to change the password, the user needs to enter the new
password twice. Once the user clicks the application key, the new password will be activated.
At this time, if the switch does not enable multi-user, the login dialog box will be displayed (as
shown in Figure 7). The user needs to log in to the web page again. The user must enter the
new anonymous user password to log in to the web pag
At the same time, users can configure multiple users through this page. The switch does
not have multiple users by default, that is to say, the multi-user management function is not
enabled by default. At this time, login does not need to verify the user name and password of
multiple users. For Telnet, when a user name is added, the multi-user management function is
enabled. When all users are deleted, the multi-user management function is turned off. For the
web, when a user name is added, if it is a privileged user, the multi-user management function
is enabled. When all privileged users are deleted, the multi-user management function is
turned off. When the multi-user management function is enabled, the anonymous user
password will not take effect. Logging in to telnet and web requires multi-user user user name
and password verification. When the multi-user management function is turned off, if the
anonymous user password is configured, login telnet and web need to verify the password of
the anonymous user
19
Figure 4-3 user management page
4Security management
Figure 4-4 is the security management configuration page. Through the configuration of
this page, the administrator can control the network management services Telnet, web and
SNMP, enable or disable these services, and connect these services with the ACL group of IP
standard to implement source IP address control and control the host's access to these
services
By default, Telnet, web and SNMP services are turned on, and ACL filtering is not done,
that is, all hosts can access the three services of the switch. If the administrator does not want
to provide one or several services to other users for security, he can shut down one or several
services. If the administrator only wants a specific host to access one or more of these
services, he can do ACL filtering for one or more of these services. When a service wants to
do ACL filtering, it needs to open the service and select an IP standard ACL group (1-99). At
this time, the ACL group must exist
It should be noted that if the administrator controls the web service on this page (such as
turning off the web service), the user may no longer be able to use the web page. At this time,
the administrator can log in to the switch through other ways and control the web service, so
that the user can use the web page (such as turning on the web service)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Tycon Power TP-SW8GAT/BT/24-SFP ユーザーマニュアル

カテゴリー
ネットワークスイッチ
タイプ
ユーザーマニュアル