VIBRAPHONE
YV3030MS
EnglishDeutschFrançaisEspañolPortuguês
Make sure to read the “PRECAUTIONS” on page 2.
Lesen Sie unbedingt die "VORSICHTSMASSNAHMEN" auf Seite 2.
Assurez-vous de lire “PRÉCAUTIONS D'USAGE” à la page 2.
Asegúrese de leer "PRECAUCIONES" en la página 2.
Certifique-se de ler "PRECAUÇÕES" na página 2.
Pусский
Owner’s Manual
Benutzerhandbuch
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Руководство пользователя
JA EN DE FR ES PT RU ZH KO
Обязательно прочтите разделы «ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ» на стр. 2.
2•YV3030MS Owner’s Manual
DMI-7 1/1
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
• Repairs or part replacement should not be attempted unless
instructions are provided in the manual.
• Do not disassemble the gas spring. Since high-pressure gas is
sealed inside the gas spring, any attempt to disassemble it is
dangerous and creates a high risk of injury.
• Assemble the instrument in the proper sequence by following
the assembly instructions in this manual. Also, make sure to
tighten the screws or bolts regularly. Failure to do so may result
in damage to the instrument or cause the instrument to overturn,
possibly causing injury.
• When assembling or moving the instrument, always use two or
more people. Failure to do so might result in damage to the
instrument or the instrument overturning, possibly causing
injury.
• Do not place the instrument in an unstable position where it
might accidentally fall over.
• Lock both left and right casters except when moving or
transporting the instrument. Failure to do so might result in the
instrument moving or overturning, possibly causing injury.
• When lifting and transporting the instrument, support the side
frames with two or more people.
• The instrument should only be moved across smooth, flat
surfaces when using the casters. On a sloped, unstable or gravel
surface, the instrument may overturn or run out of control, and
possibly cause injury.
• Never run when moving or transporting the instrument using the
casters. Doing so can result in the instrument hitting an obstacle
or wall and causing serious injury.
• Do not go near the instrument during an earthquake. Strong
shaking during an earthquake could cause the instrument to
move or tip over, resulting in damage to the instrument or its
parts, possibly causing injury.
• When the instrument rattles, makes noise or vibrates,
immediately stop using it, and tighten all screws again. Failure to
do so may result in the instrument overturning and could
possibly cause injury.
• Never touch the rotating pulleys. Doing so may result in pinching
your fingers, etc.
• Do not insert your hands or feet in any gaps on the casters or
active parts of the pedal. Doing so may result in them being
pinched and could possibly cause injury.
• Do not play around the instrument. Doing so may cause you to
bump into the instrument, possibly resulting in injury. It also
may cause the instrument to overturn. Do not allow children to
play around the instrument.
• Do not lean, rest your weight or place heavy objects on the
instrument. Doing so may result in the instrument overturning,
damage to the tone bars or frame, or injury to you or others.
• Keep small parts out of the reach of infants. Your children may
accidentally swallow them.
Do not disassemble
Assembly
Transportation and Installation
Handling
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument.
YV3030MS Owner’s Manual • 3
NOTICE
To avoid the possibility of damage to the product, follow
the notices below.
Handling
• Do not strike the tone bars with glockenspiel mallets or
any other solid objects. Doing so may dent or scratch
the tone bars, altering their pitch.
• Do not use the instrument in locations with poor ventila-
tion.
• When moving the instrument, make sure all caster stop-
pers are released. Lift the instrument slightly whenever
moving it over surfaces that are not smooth or flat.
• When moving the instrument, move it gently avoiding
shocks and impacts. The instrument is sensitive to
shocks and may become damaged.
• If the instrument is often moved, screws, parts, etc., may
become loose. After moving the instrument, check and
make sure all screws, parts, etc., are firmly fastened.
Firmly tighten all loose items.
• Do not apply excessive force to lift the frame end as it
may pull the gas spring off from the leg.
• Do not expose the instrument to rain, water, excessive
dust or vibrations, or extreme cold or heat (such as in
direct sunlight, near a heater, or in a car during the day)
to prevent the possibility of instrument disfiguration or
malfunction.
• Do not place vinyl, plastic or rubber objects on the
instrument, since this might discolor the instrument.
Maintenance
• When cleaning the tone bars, wipe with a soft and dry
cloth. Stains that are visible may be wiped off using a
small amount of ethyl alcohol applied to a soft cloth. Do
not use paint thinners, solvents or a wet cloth.
INFORMATION
Casters
Before playing the instrument, make sure the casters and
legs are parallel. As the angle between the leg and the
caster approaches at a right angle, a rattling sound is more
likely to be generated from the caster when playing.
About this manual
• The illustrations as shown in this manual are for instruc-
tional purposes only, and may appear somewhat differ-
ent from those on your instrument.
• The company names and product names in this manual
are the trademarks or registered trademarks of their
respective companies.
4•YV3030MS Owner’s Manual
Introduction
Thank you for purchasing the Yamaha VIBRAPHONE YV3030MS.
This vibraphone, can be used in school performances or playing by hobbyists.
To get full use and performance enjoyment from this instrument, please read this owner’s manual carefully before using it. After you
have read the manual, keep it in a safe and handy place for future reference.
For handling a vibraphone variable-speed driver, refer to the manual bundled with the vibraphone variable-speed driver.
Confirmation of Packing Contents
Please make sure your package includes the parts shown below before assembling the instrument.
* If any parts are missing, please contact your dealer or qualified Yamaha service personnel.
q Owner’s Manual
(this document)
w Main unit × 1 (tone bars, frame, damper,
driver attachment)
NOTE
A vibraphone variable-speed driver YVD20 (sold separately) and
an AC adaptor (sold separately) are required for rotating the fans
of the YV3030MS.
t Resonators (natural tone side) × 1
y Resonators (accidental tone side) × 1
u Drop cover × 1
i M8 socket screw × 2, M6 socket screw × 7,
cup head square neck bolt × 1, wing nut × 1
* These parts (M6 socket screw × 1, cup head square neck bolt,
and wing nut) for the YV3030MS are specifically used for
assembling the vibraphone variable-speed driver YVD20 (sold
separately). Be careful not to lose them.
o Hex key × 1
!0 Yamaha representative or authorized distributor list x1
VIBRAPHONE
YV3030MS
Owner’s Manual
Benutzerhandbuch
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
EnglishDeutschFrançaisEspañolPortuguês
JA EN DE FR ES PT ZH KO
Make sure to read the “PRECAUTIONS” on page 2.
Lesen Sie unbedingt die "VORSICHTSMASSNAHMEN" auf Seite 2.
Assurez-vous de lire “PRÉCAUTIONS D'USAGE” à la page 2.
Asegúrese de leer "PRECAUCIONES" en la página 2.
Certifique-se de ler "PRECAUÇÕES" na página 2.
e Legs × 2
r Pedal stay × 1
YV3030MS Owner’s Manual • 5
Part Names
Assembly
When assembling the instrument, always use two or more people.
Assemble the instrument in a place where there is sufficient room.
1. Align the white marks on the left leg and pedal
stay, and then connect the left leg, pedal stay and
right leg.
In this step, also turn the slant stay connectors upward and
the damper pedal towards to you.
2. Using the included hex key, temporarily secure
the four screws.
Use the larger screws to secure the pedal stay.
Side frame
Tone bars (natural tone)
Pedal stay
Caster with stopper
Side frame
Resonators
(accidental tone)
Gas spring
Resonators
(natural tone)
Damper pedal
Damper belt
Caster with stopper
Gas spring
Tone bars (accidental tone)
Damper
Driver attachment
Slant stay
Right leg
Left leg
CAUTION
Right leg
Left leg
Pedal stay
Be careful not to pinch
your fingers!
CAUTION
Damper pedal
Slant stay
Slant stay
White marks
Slant stay
connectors
6•YV3030MS Owner’s Manual
Assembly
3. Tighten the screws in this order: q slant stays, w
pedal stays.
4. Set the main unit upside down.
To prevent damage to the floor and the main unit, leave the
main unit in the shipping package, or place a rug or soft
cloth on the floor underneath the main unit.
5. Turn the leg assembly upside down, put it on the
main unit, and then secure it with the four screws.
NOTE
If the direction of legs and main unit is not correct, the location of
pins and holes may be misaligned, and may not be assembled
properly.
6. To prevent the pedal from moving uncontrollably,
secure the damper by hooking the damper belt tip
to the hook of the main unit.
7. Stand the instrument upright while being careful
to avoid overturning or falling of instrument.
8. Lock the casters by pressing the stoppers on the
left and right casters.
9. Lower the damper pedal.
Unbuckle the damper belt to avoid excessive tension to the
belt when raising the position of the instrument height in
step 11.
Be careful not to pinch
your fingers!
CAUTION
Damper belt
YV3030MS Owner’s Manual • 7
Assembly
10.
Attach the resonators.
Insert the resonators from underneath the main unit and
rest the high sound side and then the low sound side onto
the resonator holders.
NOTE
• Make sure not to confuse the natural tone side and acci-
dental tone side resonators.
• Take care not to bump the resonators against the legs
etc.
11.
Adjust the instrument height.
Pulling the lever on the left and right leg raises the height,
while firmly pressing down on the side frame while pulling
the lever lowers the height. When you release the lever, the
instrument height is fixed at that height.
NOTE
• The legs have a scale that serves as a guide for adjust-
ing the height.
• We recommend that you lower the height slightly more
than you intend, and then make minor adjustments
while raising it little by little.
• Adjust the left and right height at the same time to main-
tain the level of the tone bars.
• Grease is applied to the cylinders of the legs to allow for
smooth height adjustment. If the grease sticks to your
hands, rinse it off with running water.
• Unbuckle the damper belt when you re-adjust the instru-
ment height.
12.
Adjust the depth of the pedal pressing.
Unbuckle the damper belt, adjust the position of the pedal,
and then fix it by buckling the belt.
13.
Make sure all screws are tightened securely.
Assembly is now complete.
1
2
1
2
Resonator
Holders
First, place the high sound side onto the corre-
sponding resonator holders.
To engage the low sound side, lift it over the resona-
tor holders, and then insert it into the gap between
the two holders, as shown in the illustration.
Resonator
Holders
Accidental Tone Side
Resonators
Low Sound
Side
High Sound
Side
Lever
Damper pedal
3–4 cm
Floor
8•YV3030MS Owner’s Manual
Specifications
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website
and download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check
with your Yamaha dealer.
Comparison with piano keyboard
Range Three octaves: F33–F69
Bars Aluminum alloy
Height Adjustable From 66 cm to 85 cm
Dimensions (W×D) 127 cm × 74 cm
Weight 35 kg
Included Accessories Drop cover, hex key
Separately Sold Accessories Vibraphone variable-speed driver (YVD20)
YV3030MS
Middle C
YV3030MS Owner’s Manual • 9
MEMO
VDF8380
Manual Development Group
© 2021 Yamaha Corporation
Published 03/2021
POTO-B0
/