IK Multimedia AXE I-O ONE ユーザーマニュアル

USB audio interface with

advanced guitar tone shaping

USER MANUAL

Contents

2

Table of Contents

Contents 2

English 3

AXE I/O ONE 3

Register your AXE I/O ONE 3

1. AXE I/O ONE overview 4

1.1 Top panel 4

1.2 Front panel 5

1.3 Rear panel 6

2. Installation and setup 7

2.1 Software installation 7

2.2 Setup 7

3 Dedicated guitar features 9

3.1 Direct amplifier output & Re-Amplification 9

3.2 JFET / PURE input (only for Instrument Input) 10

3.3 Pick-Up selector (only for Instrument Input) 11

3.4 Variable impedance (Z-TONE™) control (only for Instrument Input) 12

3.6 External control 13

4 Setup your DAW 13

5 Connecting microphone 13

5.1 Condenser microphone 13

5.2 Dynamic microphone 13

5.3 Ribbon microphone 13

6 Connecting instrument 14

7 Connecting loudspeakers and headphones 14

8 Direct monitoring 15

9 Control software 15

9.1 Interface view 16

9.2 Controller tab 17

10 Specifications 18

Warranty 20

Support and more info 20

English

3

AXE I/O ONE

Thank you for purchasing AXE I/O ONE.

Your package contains:

• AXE I/O ONE

• USB-A to USB-C cable

IK Multimedia’s award-winning AXE I/O premium audio interface sets a new standard for guitar-oriented

recording, with powerful tone shaping and revolutionary ways to integrate with your real pedals and amps.

AXE I/O ONE delivers the same great features in a super-compact 1 in / 3 out audio interface. Track pristine

vocals through the included PURE mic preamp, explore a massive range of electric guitar tones via IK’s ground-

breaking Z-TONE instrument input, and enjoy easy reamplification with the onboard AMP out.

AXE I/O ONE combined with the massive included software bundle, is a world-class studio that fits into your

guitar case.

Register your AXE I/O ONE

By registering, you can access technical support, activate your warranty and receive free JamPoints™ which will

be added to your account. JamPoints™ allow you to obtain discounts on future IK purchases! Registering also

keeps you informed of all the latest software updates and IK products.

Register at: www.ikmultimedia.com/registration

English

4

1. AXE I/O ONE overview

1.1 Top panel

123

54

89

10

6

7

1. GAIN - adjusts the input gain for the signal at the input.

2. Peak Meters - the input has a dedicated 5-segment peak meter, with 1-second hold on CLIP, that indicates

the level of the input signal.

3. Z-TONE™ - Variable impedance control - the front control named Z-TONE™ allows you to change the input

impedance on the instrument input allowing for unique possibilities for tone shaping your instruments.

4. JFET/PURE - Preamp topology selector - this selector allows you to select two different preamp topologies

for your connected instrument: JFET preamp type and Pure preamp type.

5. PASSIVE/ACTIVE - Pick-Up selector - this selector allows you to match the type of pick-up installed on the

connected instrument.

6. MIDI IN/OUT LEDs - these LEDs illuminate when MIDI data is received from/transmitted to the MIDI port.

USB LED - this LED illuminates when the unit is recognised by the computer to which it is connected.

INST, MIC LEDs - active input indication with auto select. If no connection is made, or if an XLR is

connected to the Combo input, the MIC input will be activated, and the corresponding LED will light up; if an

instrument is connected to the Combo input, the INSTRUMENT input will be selected and the corresponding

LED will light up.

7. 48V - This switch enables 48V phantom power for the XLR microphone input. The switch illuminates when

phantom power is selected.

English

5

8. MONITOR - the Monitor knob allows you to blend your input signals with the playback streams from your

computer. This allows you to monitor your input signal with zero latency. If the knob is positioned at 12

o’clock, the input signal and the playback stream will be equally balanced. Turning the knob to the left will

increase the level of the direct signal; turning to the right will increase the level of the playback stream from

the DAW. This control works both for Outputs 1-2 and Headphones.

9. HEADPHONES - allows you to control the headphone volume.

10. MASTER - main output level control – this control adjusts the level at Outputs 1 and 2 on the rear panel.

1.2 Front panel

3

2

1

1. MIC/INST IN - XLR Combo type input socket - connect microphone or instrument (e.g., guitar).

2. HEADPHONE OUT-connectonepairofheadphonestothe1⁄4”(6.35mm)TRSjacksockets.The

headphone outputs always carry the signals that are currently routed to outputs 1 & 2.

3. AMP OUT -thisisathird1/4”physicalunbalanced,floatingoutputwithselectablegroundlift(controlled

with software). It is independent from main Outputs 1-2. This output is specifically designed to allow the

interface to feed guitar amps or stomp pedals without the typically associated risk or hum or buzzing noises

caused by ground loops or mismatched levels and impedances.

English

6

1.3 Rear panel

2

3

4 5

1

1. USB port - Type C connector - connect the AXE I/O ONE to your computer with the supplied cable

2. Kensington security lock - secure your AXE I/O ONE to a suitable structure if desired.

3. MIDI IN/OUT - standard 5-pin DIN sockets for connection to external MIDI equipment.

4. EXTERNAL CONTROL-usethese1/4”(6.35mm)jackstoconnectexternalcontrollerpedals(singleor

dual switches, continuous expression pedals). MIDI messages sent are freely assignable from the “Control

Software”.

5. LINE OUTPUTS1/Land2/R-Outputs1/Land2/Rarebalancedandfloatinganaloguelineoutputson1⁄4”

(6.35 mm) jack sockets; use TRS jacks for a balanced connection. Outputs 1/L and 2/R will normally be

used to drive the primary monitoring system.

English

7

2. Installation and setup

2.1 Software installation

All software required by the AXE I/O ONE is available for download from the IK Multimedia website (www.

ikmultimedia.com/products/axeioone).Bydownloadingthe“AXEI/OONEDriversandControlSoftware”youwill

find:

MAC users: the installer containing the AXE I/O ONE Control Software.

Windows users: the package includes the AXE I/O ONE Control Software and the necessary drivers for the

interface.

1. Using your web browser, go to www.ikmultimedia.com/products/axeioone and go to the Downloads section.

2. Youcannowdownloadthe“AXEI/OONEDriversandControlSoftware”file(MacandWindowsversions

available).

3. Downloadandinstallthe“AXEI/OONEDriversandControlSoftware”version(MacorWindows)appropriate

for your computer and follow all on-screen instructions.

4. When the installation is complete, restart your computer.

5. After restart, connect the AXE I/O ONE to your computer with the supplied USB cable.

2.2 Setup

1. Download and install the AXE I/O ONE Drivers and Control Software as described above.

AXE I/O ONE Control Software

FREE DOWNLOAD

ikdownloads.com/axeioone

English

8

2. Connect the AXE I/O ONE to your computer with the supplied USB cable.

3. You can connect instrument or microphone to the Combo input and set its gain with the gain knob on the

top of the interface.

4. Connect speakers, amplifiers or other line devices to the balanced outputs on the rear panel of AXE I/O

ONE.

5. If needed, you can connect external MIDI devices to the physical MIDI ports (Input/Output).

English

9

3 Dedicated guitar features

3.1 Direct amplifier output & Re-Amplification

RE-AMPLIFICATION

in from MIC

Among the features that make AXE I/O ONE the definitive guitarist interface is the re-amplification feature. The

“AMPOUT”isathirdphysicaloutputwhichisindependentfrommainOutput1-2.Withthisoutput,youcan

feed a DI recorded guitar to external analogue stomps or a real amplifier, still being able to monitor the session

from main Output (1-2). The external stomps (or the miked amplifier) will be connected back to Input to return

into the DAW on a newly recorded track.

The AMP OUT is a floating unbalanced output topology specifically designed to properly interface with guitar

or bass amplifiers of any kind for maximum signal fidelity and integrity. This ensures the immunity from noises

caused by ground loops with the Amps, so actually allowing re-amping without the typical associated noise/hum

issues.

English

10

3.2 JFET / PURE input (only for Instrument Input)

Thanks to the front panel selector it is possible to select two different preamp topologies for your connected

instrument: JFET preamp type and Pure preamp type.

The discrete JFET (field-effect transistor) circuitry adds a tiny bit of color and harmonics to the signal, giving your

instruments some added warmth.

Pure circuitry results in a more linear response featuring the absolutely cleanest signal path possible, for best

transparency and clarity.

Each amplifier topology offers complimentary sonic performance to the other, and both are widely used in

professional recording and stage work. Note: this control only works when the Pickup selector is in the Passive

position.

English

11

3.3 Pick-Up selector (only for Instrument Input)

PICK-UP

AXE I/O ONE works perfectly with both Passive and Active guitar or bass pickups, having independent circuitry

that suits perfectly both topologies. Passive electric guitar pickups exhibit significantly higher output impedance

thantheactivecounterpart,amongothersignificanttonedifferences,butneitherofthetwois“better”or

“worse”thantheother:indeedtheyhavedifferentbehaviors.Toproperlycouplethisdiversityofguitarpickups

in the most musically pleasing manner, AXE I/O ONE offers a pickup selector that allows the artist to select

between Active (when using an active pickup) and Passive (when using a passive pickup).

English

12

3.4 Variable impedance (Z-TONE™) control (only for Instrument Input)

All passive pickups (being them single coil, humbucker, split, etc..) have a certain sound character that is also

determined by the loading impedance. The Z-TONE™ control allows you to change the input impedance on the

instrument input therefore providing a very creative way of shaping the tone of your instruments.

The beauty of this system is that it allows you to discover tonal shades from your instruments that you have

never heard before, by shaping the tone right at the source, within the pickups, instead of what is normally done

by using post-processing tools of any kind.

Feel free to experiment without rules with this knob! You will find your tone becomes generally more thick and

bold by reducing the impedance (control is moved clockwise) and, on the other hand, more crisp and sharp

when rotated counter-clockwise.

For example if you find your high gain tones to be too harsh, try setting this control at mid position, and you’ll

experience what the Z-TONE™ can magically do.

If you’re recording a bass (with passive pickups) and find it sounds a bit thin, try the same. The sound will

immediately feel more bold, solid and bigger.

The key here is experimentation! Feel free to check it out on your instruments, on various configurations, the

possibilities are really endless.

Settingsstartfromthehighestimpedancevalue(named“Sharp”)tothelowestimpedancevalue(named“Bold”)

The Z-TONE™ circuit only works with passive pickups of any kind.

Using it on active pickups will not provide any significant useful change to the sonics of the instrument.

Note: AXE I/O ONE is very useful for feeding analogue stomp boxes from DAW tracks using the AMP output.

The best way to get the Stomp signal back into the DAW is by using the Instrument input. This way the

Z-TONE™ circuit will also be very useful because most vintage stomps can actually change the way they sound

depending on the load impedance, so experimentation in this usage is very welcome as well.

English

13

3.6 External control

Connect up to two external controllers here to send MIDI control messages. You can use any available

“momentary”or“sustainpedal”typefootswitchthatincludesa1/4inchconnector.Bothnormallyopenand

normally closed switches are supported. AXE I/O ONE also support continuous expression pedals for controlling

realtimeparameterslikeWah,Volume,FXdepthetc.Any1/4”TRSconnectorexpressionpedalwillwork

with AXE I/O ONE. MIDI messages associated with these controllers are freely assignable from the “Control

Software”.

4 Setup your DAW

The AXE I/O ONE is compatible with any Windows-based DAW that supports ASIO or any Mac-based DAW

that uses Core Audio. After installing AXE I/O ONE Control Software and connecting the hardware, you can start

using your AXE I/O ONE with your DAW.

It is possible that your DAW may not automatically select the AXE I/O ONE as its default I/O device. In this case,

you must manually select the AXE I/O ONE as the audio hardware on your DAW’s Audio Setup page. Please

refer to your DAW’s documentation (or Help files) if you are unsure where to select the ASIO/Core Audio driver.

Once the AXE I/O ONE is set as the preferred Audio Device in your DAW, the single input and the 3 outputs will

appear in your DAW’s Audio I/O preferences.

5 Connecting microphone

Always connect microphones to AXE I/O ONE with XLR-to-XLR balanced cables. This will ensure a pristine and

clean performance from your microphone with AXE I/O ONE.

NOTE: In your audio software, select the AXE I/O ONE as the input source of the track you will be recording to.

Adjust the channel gain knob until you have a sufficient audio signal without clipping.

5.1 Condenser microphone

Most condenser microphones require external 48V phantom power. If phantom power is ON, switch it OFF,

and then connect your microphone. Turn phantom power ON only after the microphone is connected. Once it’s

turned ON, check that the phantom power LED has become red.

5.2 Dynamic microphone

Before connecting dynamic microphones make sure that phantom power is turned OFF. Check that the

Phantom LED is turned off.

5.3 Ribbon microphone

Before connecting a ribbon microphone, turn OFF phantom power and check the microphone’s operating

instruction manual to see if it requires it. Most ribbon microphones don’t require phantom power, and some can

even be damaged by it. If you’re in doubt just leave it OFF. If the microphone won’t work, check its user manual,

it may need phantom power.

English

14

6 Connecting instrument

Connectyourguitar,bassoranyothermonoinstrumenttotheinstrumentinputonAXEI/OONEusinga1⁄4”

plugunbalanced(TSor“mono”)guitarcable.

Please refer to Section 3 of this manual for the complete description of features dedicated to the instrument

input.

NOTE: In your audio software, select the AXE I/O ONE as the input source of the track you will be recording to.

Adjust the channel gain knob until you have a sufficient audio signal without clipping.

7 Connecting loudspeakers and headphones

The1/4”jackoutputs1/Land2/Rontherearpanelwillnormallybeusedtodrivemonitorspeakers.Self-

powered (active) monitors incorporate internal amplifiers, and may be connected directly. Passive loudspeakers

will require a separate stereo amplifier; in this case, the rear panel outputs should be connected to the amplifier’s inputs.

Line outputs 1/L and 2R are electronically balanced and floating and will automatically compensate the level

when connection is balanced or unbalanced.

OnthefrontpanelofAXEI/OONEispresentone1/4”(6.35mm)jacksocketwhereyouconnectapairof

headphones whose level can be controlled with the headphone knob.

English

15

8 Direct monitoring

When recording an audio signal into your audio software, there is often a slight delay before it reaches the

outputs. This delay, called latency, is caused by the computer processing time required to process the audio.

Since this delay can be distracting, AXE I/O ONE provides a direct monitoring path from the inputs to the

outputs, and this is controlled by the Monitor knob. The Monitor knob allows you to blend your input signals

with the playback streams from your computer. This allows you to monitor your input signal with zero latency. If

the knob is positioned at 12 o’clock, the input signal and the playback stream will be equally balanced. Turning

the knob to the left will increase the level of the direct signal; turning to the right will increase the level of the

playback stream from the DAW.

WhenMonitorissettoDIRECT,makesurethatanysoftwaremonitoringoptionfordirect(or“lowlatency”)

monitoringisdisabled.Disablinglowlatencymonitoringprevents“double-monitoring”ofinputaudiosignals

whenusingtheDirectMonitoringfeature.When“double-monitoring”occurs,therewillbeanincreaseinvolume

andanundesirable“phasing”sound.Formoredetailsaboutitsmonitoringfunction,refertothedocumentation

for your audio software.

IMPORTANT: Always makes sure MONITOR knob is set fully clockwise (DAW) when connecting microphones.

This is because even if your DAW is not running or does not have an active recording track, loud feedback could

occur if your monitoring level is high and the MONITOR knob is set on DIRECT.

9 Control software

This is a macOS and Windows software program that controls all the functions of the AXE I/O ONE, also

providing additional information about the status of AXE I/O ONE. From this software you will have extended

and comprehensive metering, have control over output levels, sample rate, MIDI setup, and other important AXE

I/O ONE options.

To open the Control software:

After installing the Control software on your computer (refer to Section 2.1 of this manual for more information)

click the icon on your desktop to launch it.

Assuming that your AXE I/O ONE interface is connected to your computer with the USB cable, the Control

software GUI (Graphical User Interface) will appear as shown on the sections below. The green State ‘LED’ at

the screen top left should be illuminated; this confirms that the AXE I/O ONE interface is connected and properly

working.

English

16

9.1 Interface view

State. This LED shows when an AXE I/O ONE unit is connected and active.

MIDI In/Out. these LEDs shows when there is MIDI activity on the AXE I/O ONE physical MIDI ports.

Sample Rate. Here you can set the working sample rate for the AXE I/O ONE unit, from 44.1 kHz to 192 kHz.

Remember that in most cases, DAWS and host applications will likely control this value by their end, not

allowing it to be forced differently. For this reason, you might see this value return to its previous state when you

attempt changing it.

To Amp Out. When activated, this button routes the Instrument Input directly to the Amp Out with zero latency.

Audio Input section. Here you can see the input channel active source (Instruments or Mic) and monitor the

level on high precision peak meters. You can also switch 48V phantom power on and off. Remember that

phantom power will only be applied to the XLR input.

Audio Output section. Here you can see the output channels levels on precision peak meters, you can adjust

the output levels of all outputs with the large sliders, or you can quickly mute each output individually.

GND LIFT. The Amp Output is a specially designed floating output made to drive amplifiers and sensitive

vintage stomps without the typically associated ground loop noises, hum and buzzes. Depending on what else

is connected to the AXE I/O ONE and what grounding scheme is implemented in the setup the amp connection

can be cleaner with GND LIFT active or not active. The default position is GND LIFT, with lift active, but if you

hear some buzz or noise when connecting an high gain guitar amp, try switching off the GND LIFT.

English

17

9.2 Controller tab

The Controller tab gives you control over the 2 controller inputs. Set behavior, MIDI channel, MIDI CC#,

minimum and maximum values, and more, to dial in the best settings for whatever application you want to

control.

English

18

10 Specifications

Common

AD and DA resolution: 24-bit

Sampling rate: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz

Host connection: USB Type-C socket

Mic Input

Configuration: Class-A discrete differential microphone preamp, pin 2 hot

Input impedance: 4 kOhms differential

Input level, min gain: 0 dBFS is obtained with a +7 dBu signal at the XLR input

Input level, max gain: 0 dBFS is obtained with a -42 dBu signal at the XLR input

Frequency response: From 9 Hz to 45 kHz within 0.5 dB (96 kHz sample rate)

Dynamic range: 108 dB(A)

THD+N: -104 dB(A) at -10 dBFS

Instrument Input

Configuration: Multiple topology instrument preamp

Input impedance, PASSIVE mode: Variable from 1 MOhms down to 2.2 kOhms

Input impedance, ACTIVE mode: 10 kOhms

Input level, min gain: 0 dBFS is obtained with a +10.5 dBu signal at the TS input

Input level, max gain: 0 dBFS is obtained with a -19 dBu signal at the TS input

Frequency response: From 11 Hz to 45 kHz within 0.5 dB (96 kHz sample rate)

Dynamic range: 108 dB(A)

THD, PURE mode: 0.0018 % (-1 dBFS input)

THD, JFET mode: 0.42 %

Line Outputs 1-2 (Monitor)

Configuration: Electronically balanced

Output impedance: 150 Ohms balanced, 75 Ohms unbalanced

Output level: 0 dBFS corresponds to +12.8 dBu

Frequency response: From 10 Hz to 42 kHz within 0.5 dB (96 kHz sample rate)

Dynamic range: 108 dB(A)

THD @ -1 dBFS: 0.0015%

THD+N: -95 dB(A) at -1 dBFS

Channels 1-2 crosstalk: 109 dB(A)

English

19

Output 3 (Amp output)

Configuration: Unbalanced, floating, with selectable ground lift

Output impedance: 75 Ohms

Output level: 0 dBFS corresponds to -3.5 dBu

Frequency response: From 20 Hz to 44 kHz within 1 dB (96 kHz sample rate)

Dynamic range: 108 dB(A)

THD+N: -93 dB(A)

Headphone Output

Output impedance: Virtually ideal source (zero Ohms) until clipping

Maximum output level: +5 dBu into 50 Ohms load (approx 40 mW)

Frequency response: From 1 Hz to 44 kHz within 1 dB (96 kHz sample rate)

Dynamic range: 108 dB(A)

English

20

Warranty

Please visit:

www.ikmultimedia.com/warranty for the complete warranty policy.

Support and more info

www.ikmultimedia.com/support

https://www.ikmultimedia.com/products/axeioone

ページが読み込まれています...

IK Multimedia AXE I-O ONE ユーザーマニュアル

IK Multimedia AXE I-O ONE ユーザーマニュアル

他の言語で

その他のドキュメント