2. SMSL
  3. DO400
DO400

SMSL DO400 ユーザーガイド

  • SMSL DO400 デジタルオーディオプレーヤーのユーザーマニュアルの内容を理解しました。MQAデコード、高出力、多様な接続端子など、このデバイスに関するご質問にお答えします。
  • DO400の対応サンプリングレートは？
    DO400の出力方式は？
    DO400はMQA-CDを再生できますか？
    DO400のリモコンの電池の種類は？
使用说明书/USER MANUAL/取扱説明書
本说明书的内容可能会随版本更改如有变动, 恕不另行通知
Ver 1.0
本説明書の内容は版によって予告なしに変更される
The contents of this manual may be changed with the edition, and are subject to change without notice.
安全注意事项
请将本音响系统安装在通风良好、阴凉、干燥、干净的位置，远离直射阳光热源、振动、灰尘、 潮
湿或寒冷。
只能使用本机指定的电压。使用高于指定数值的电压很危险，而且可能导致火灾，损坏本机或
造成人身伤害。对于使用高于指定电压造成的任何损害，
我司将不负任何责任。
不要试图自行改造或修理本机。如果需要任何服务，请与销售或者我司客服人员联系。不管有
任何理由，都没有打开机壳的必要。
如果打算长时间不使用本机（比如度假时），请从墙壁交流电源插座上断开电源线的连接。
重要提示：
本说明书所提到的产品规格和资讯仅供参考。如有内容更新，恕不另行通知。
保修条款
一、服务期限
佛山双木三林科技有限公司承诺产品的良好品质，产品自售出之后7天内正常使用情况下出现
故障，客户可以选择退货或者保修（不影响二次销售才可退货）。正常使用一年内出现故障可以
免费保修。
二、购买日期以销售商开出的购机发票或收据日期为准，网购可以交易截图为准。
三、有以下情况都不能享受“三包”服务
1.一切人为因素损坏，包括非正常工作环境下使用或不按照说明书使用。
2.用户私自拆机、改装、维修。
3.使用非指定或许可的配件造成损坏的。
4.机身的QC或保修贴损毁。
5.不能出示有效购机凭证。
6.不属于本公司产品。
四、保修方式为送修
此条款只适于中国大陆，其它地区请参考当地销售代理商的规定和国家法规。
特点
支持MQA解码，支持MQA-CD ;
美国ESS新一代旗舰DAC芯片ES9039MSPRO,内置MQA硬解码；
全新第三代XMOS XU-316，PCM支持到32bit/768kHz，DSD支持到DSD512；
使用了超低相噪和优化的时钟处理电路处理，以达到超低的时钟抖动；
高输出功率, 16欧姆输出功率达6W, 32欧时达到3W ;
全平衡设计, 4路超低失真精密线性反馈电路(PLFC)!
三种耳机输出接口，分别是4-XLR、4.4mm和6.35mm，以满足不同的用途
除蓝牙以外其它输入口均支持DSD传输，同轴，光纤，AES/EBU支持DoP64；
固件升级功能,用户可以自行升级系统和USB的固件；
内置低噪声电源处理，同时提高电源效率，功耗更低；
特别设计的分立元件线性稳压电源和多个低噪声稳压电源，为模拟电路提供
低噪声电源；
美国高通最新蓝牙5.1芯片支持LDAC 24bit/96kHz , APTX/HD ， SBC ， AAC ；
高品质镀金输入输出连接端子；
日本音频协会(JAS)Hi-Res认证；
配备遥控器和全功能遥控。
技术参数
SMSL保留在不另行通知的情况下进行可能导致规格或特性更改的改进的权利。
输入方式 ...............................................................................................USB / 光纤 / 同轴 / 蓝牙 / I
2
S / AES
输出方式 ...............................................................................................
单端线路 / 平衡线路 / 平衡耳机x1
4.4mm平衡耳机x1 / 非平衡耳机x1
线路输出幅度...........................................................平衡线路 5.2Vrms
单端线路 2.5Vrms
耳放输出功率
...................................................................................................................
6000mW x 2(16Ω)
...........................................................................................................................................
3000mW x 2(32Ω)
...........................................................................................................................................
700mW x 2(300Ω)
...........................................................................................................................................
350mW x 2(600Ω)
THD+N......................................................................平衡线路 0.00005%(-125dB)(UN-WTD)
单端线路 0.00007%(-123dB)(UN-WTD)
耳放输出 0.00009%(-120dB)(UN-WTD)
动态范围...................................................................平衡线路 133dB
单端线路
128dB
耳放输出
126dB
信噪比.......................................................................平衡线路 133dB
单端线路
128dB
耳放输出
126dB
输出阻抗
....................................................................
线路输出
100Ω
耳放输出
接近0Ω
耳放高增益................................................................平衡接口 +20dB
非平衡接口 +14dB
USB传输方式...................................................................................................................USB2.0(异步传输)
USB兼容性 ..................................................................................Windows 7 / 8 / 8.1 / 10 / 11(需要驱动)
Mac OSX10.6以上、Linux(不需要驱动)
MQA decoder..........................................................................................................USB / 光纤 / 同轴 / AES
采样率与位深:
USB PCM 44.1~768kHz(32bit)
DSD
2.8224~22.5792MHz (1bit)
光纤/同轴 44.1~192kHz(24bit)
DoP DoP256(USB),DoP64(光纤/同轴)
蓝牙规格.......................................................................................5.1(支持SBC,AAC,aptX,aptX HD,LDAC)
消耗功率................................................................................................................................................<40W
待机功耗...............................................................................................................................................<0.5W
体积......................................................................................................................245X186X42mm(WxHxD)
关于遥控器
如果遥控器距离本机很近时操作仍无效，请用新电池更换。
如果要长时间不使用遥控器，请取出遥控器的电池。
按照电池处置的地方性法规处置废旧电池。
遥控器的使用
遥控器请使用2节7号(AAA)电池
。
开关机
音量加
音量减
进入二级菜单
向上
返回
向下
静音
FN按键（在菜单中定义）
输入选择
进入菜单/确认
部件介绍
4.4mm耳机插口 6.35mm耳机插口
5 6
单端线路输出 9
7平衡耳机接口 8
指示灯显示屏 红外接收窗
功能旋钮
12 3
4
蓝牙天线
平衡线路输出
10 AES/EBU输入
11 I2S输入
12
光纤输入
13
41 2 3 56 7
10
9
15 16
14
13
12
11
8
14 15
同轴输入 USB输入
电源开关
16
DO400包装清单
1 x SMSL DO400 1 x 遥控器 1 x 蓝牙天线
1 x USB线 1 x AC电源线 1 x 说明书
1 x 保修卡
功能介绍
INPUTS (输入方式)
USB (USB输入)
BLUETOOTH (蓝牙输入)
OPTICAL (光纤输入)
COAXIAL (同轴输入)
AES/EBU (AES/EBU输入)
I2S(HDMI) (I2S输入)
OUTPUTS (输出方式)
ALL LINE OUT (全部输出)
HEADPHONE OUT(耳机输出)
BALANCED (平衡输出)
UNBALANCED (非平衡输出)
PCM FILTER (PCM滤波器)
FILTER OFF (滤波器关闭NOS)
MINIMUM PHASE (最低相位)
APODIZING (切迹，快速滚降，线性相位滤波器)
LINEAR FAST (快速滚降，线性相位滤波器)
LINEAR SLOW (慢滚降，线性相位滤波器)
MINIMUM FAST (快速滚降，最小相位滤波器)
MINIMUM SLOW (慢滚降，最小相位滤波器)
LOW DISPERSION (低分散延时)
DSD FILTER (DSD滤波器)
PRE MODE(前级模式)
PRE MODE为输出接口的音量调节功能开关：
VARIABLE:输出接口音量是受控的。
FIXED:输出接口音量是固定的。
HPA GAIN(耳放增益)
LOW (低增益)
HIGH (高增益)
47k CUT-OFF (47kHz频率截止)
50k CUT-OFF (50kHz频率截止)
60k CUT-OFF (60kHz频率截止)
70k CUT-OFF (70kHz频率截止)
本机总共有9种音色模式，它是通过对DAC进行DSP处理，分别为：
Rich1、 Rich2、 Rich3（泛音丰富）
Tube1、 Tube2、 Tube3（胆味)
Crystal1、 Crystal2、 Crystal3（高清晰度）
功能介绍
SOUND COLOR(音色菜单)
音色设置是使用DAC内部DSP，做出不同的音色效果，所有这些设置不会改变频率响应曲线。设置为Standard
模式将禁用此功能!
MIN ~ MAX
(共15种，默认为5。数字越大适应抖动的范围越强，数字越小抗时钟抖动的性能越好。)
这个DPLL设定是ESS系列产品特有的功能, 它可以调整芯片内部DPLL数字锁相环电
路的带宽, 使芯片在抗时钟抖动和输入宽容度之间达到一个平衡。
它的作用:
在输入信号的时钟稳定度好的情况, 可以减小这个值, 这样系统的时钟性能更佳;
在输入信号的时钟稳定度不好的情况下, 声音有可能会有中断的现象, 增大这个值可以避免声音中断现
象的发生! 特别是使用电视作为信号源时。
DPLL (DPLL设置)
FN KEY FOR (FN按键作用)
SWITCH LINE/HPA OUTPUTS (输出选择)
BLUETOOTH (切换到蓝牙输入) PHASE (切换到输出相位)
注: 这个选项用于匹配不同的I2S接口标准, 使用前请检查信号源的接口定义。
I2S MODE(I2S模式)
NORMAL (正常，PS AUDIO格式)
NORMAL
I2S D ATA +
I2S D ATA -
I2S LRCLK +
I2S LRCLK -
GND
NC
DSD FLAG
NC
GND
GND
GND
GND
I2S MCLK +
I2S MCLK -
NC
MUTE
NC
I2S BCK +
I2S BCK -
21
18
19
REVERSED
GND
GND
I2S MCLK +
I2S MCLK -
NC
MUTE
NC
I2S BCK +
I2S BCK -
I2S D ATA -
I2S D ATA +
I2S LRCLK -
I2S LRCLK +
GND
NC
DSD FLAG
NC
GND
GND
21
18
19
AUDIO PHASE
NORMAL (2+,3-)
REVERSED (反相，DATA和LRCK反相)
INVERTED (2-,3+)
1 2+
3-
NORMAL
1 2-
3+
INVERTED
功能介绍
(范围5秒 - 60秒, 设置后, 屏会在这个时间内自动熄灭, 遥控或者旋钮任意操作屏幕会重新点亮。这样可以很
大程度减少光污染, 提升听音环境的舒适性!)
功能介绍
BRIGHTNESS (显示屏亮度设置)
DIMMER (自动熄屏)
5秒 ~ 60秒
LEVEL 1 ~ LEVEL 6
RESET (系统复位)
在蓝牙输入时，请在DO400的主菜单中选择 "RESET "并确认。系统将只重置蓝牙配对状态；
在其他输入时（非蓝牙），请从DO400的主菜单中选择 "RESET "并确认，系统将清除所有设置，包括蓝牙。
此机的USB、光纤、同轴支持MQA解码！
此机的MQA播放不要求使用特殊的播放软件, 例如foobar2000，Audirvanaplus只要 支持ASIO
或者WASAPI的音频输出就可以了, 并且在播放MQA音频时, 最好将电脑的音量调到最大, 以使
得电脑的音频输出是最佳状态。
在播放MQA文件时, 显示屏显示的采样率为音频原始采样率。
和声波标志是MQA Limited的注册商标。©2016
关于MQA
MQA（Master Quality Authenticated）是一项屡获殊荣的英国技术, 是一种兼有极高的采样率和
足够小的文件体积的高解析音频编码技术。 此机采用MQA技术, 可以接收并解码MQA音频, 提供
母带级别的声音。
有关更多信息, 请访问https://www.mqa.co.uk/how-it-works
重要提示：
本说明书所提到的产品规格和资讯仅供参考。如有内容更新，恕不另行通知。
如何播放MQA
播放MQA-CD注意事项
必须确认所播放的是一张真正的MQA-CD ;
确认CD播放器所输出的光纤或者同轴信号是未经处理的源码 。
Safety Notes
Warranty Terms
Install this unit in a well ventilated, cool, dry, clean place-away from direct sunlight, heat sources, vibration,
dust, moisture, or cold..
Use the voltage specified on this unit Only. Using this unit with a higher voltage than specified is dangerous
and may cause fire , damage to this unit, or personal injury. Our company will not be held responsible for any
damage resulting from the use of this unit with a voltage other than that specified.
Do not attempt to modify or fix this unit by yourself. Contact alesperson or customer service when any service
is needed. The cabinet should never be opened for any reason.
When not planning to use this unit for long periods of time (i.e. when going on vacation), disconnect the
power cable from the AC wall outlet.
Important note:
The product specifications and information mentioned in this manual are for reference only. The content of
this manual is subject to change without notice.
1.The Term of Service
Foshan Shuangmusanlin Technology Co., Ltd promises to offer good-quality products. If the product is
broken in 7 days after purchasing when you use it normally, you can choose to send it back for return,
replacement or repairing (only the product does not affect the second sales can be returned ). Repairing for
free in one year if you use it normally.
2.Date of purchase is in accordance with the date on invoice or receipt uesd by seller, and if you buy it on line,
you can show the screenshot of trade.
3.If an inappropriate usage causes the unit damaged, the warranty will be void. As below.
4.Sending it back to our company for repairing.
5.Contact your S.M.S.L Audio reseller for a return or replacement.
All damages by inappropriate use, including using it under non-normal working environment or without
following the instructions.
Dismantling, refitting, repairing by user in private.
Causing damage by using some fittings instead of the designative or accredited ones.
Cannot provide credible proof of purchase.
Features
Support MQA decoding and MQA-CD;
New 3rd generation XMOS XU-316, PCM support up to 32bit/768kHz,
DSD support to DSD512;
The new generation flagship DAC chip ES9039MSPRO of USA ESS has
built-in MQA hard decoding;
High output power: 6W at 16 ohm and 3W at 32 ohm ;
Fully balanced design, 4-way ultra-low distortion precision linear feedback circuit (PLFC)
Three types of headphone output connectors: 4-XLR, 4.4mm and 6.35mm, to meet different
purposes;
Specially designed linear regulated power supplies for discrete components and multiple
low-noise regulated power supplies provide analog circuits with low noise power supply;
All input ports except Bluetooth support DSD transmission, coaxial, optical fiber, AES/EBU
support DoP64;
Firmware upgrade function, users can upgrade the firmware of the system and USB by
themselves;
Built-in low-noise power processing, while improving power efficiency and lower power
consumption;
Qualcomm's latest Bluetooth 5.1 chip supports LDAC 24bit/96kHz, APTX/HD, SBC;
High-quality gold-plated input and output connection terminals;
Japan Audio Society (JAS) Hi-Res certification;
Equipped with remote control and full-featured remote control.
Specifications
SMSL reserves the right to make improvements which may result in specification or feature
changes without notice.
Input
............................................................................................
USB / Optical / Coaxial / Bluetooth / I2S / AES
Output
..............................................................................................................RCA/XLR/4.4mm Headphone Jack/
6.35mm
Headphone Jack/4-Pin XLR Headphone Jack
Line Output Amplitude
..................................................
XLR
5.2Vrms
RCA
2.5Vrms
Headphome output power
..........................................................................................................
6000mW x 2(16Ω)
............................................................................................................................................................
3000mW x 2(32Ω)
............................................................................................................................................................
700mW x 2(300Ω)
............................................................................................................................................................
350mW x 2(600Ω)
THD+N..............................................................................
XLR
0.00005%(-125dB)(UN-WTD)
RCA
0.00007%(-123dB)(UN-WTD)
HPA
0.00009%(-120dB)(UN-WTD)
Dynamic range
................................................................
XLR
133dB
RCA
128dB
HPA
126dB
SNR
.....................................................................................
XLR
133dB
RCA
128dB
HPA
126dB
Output Impedance
...........................................................
LINE OUT
100Ω
HPA
near0Ω
HPA high gain.....................................................................Balanced +20dB
Unbalanced +14dB
USB transmission..............................................................................................................USB2.0(Asynchronization)
USB compatibility.............................................................................
Windows 7 / 8 / 8.1 / 10 / 11(Needs Driver)
Mac OSX10.6 or Later、Linux(Driverless)
MQA decoder............................................................................................................
USB / Optical / Coaxial / AES
Sampling rate & Bit Width:
USB PCM 44.1 ~ 768kHz(32bit)
DSD 2.8224 ~ 22.5792MHz(1bit)
Optical / Coaxial 44.1 ~ 192kHz(24bit)
DoP DoP256(USB),DoP64(Optical / Coaxial)
Bluetooth specification.....................................................................5.1(support SBC,AAC,aptX,aptX HD,LDAC)
Power Consumption
..........................................................................................................................................<40W
Standby power
...................................................................................................................................................<0.5W
Size
........................................................................................................................................245x186x42mm(WxHxD)
Weight
....................................................................................................................................................1.45kg/3.20lbs
If the remote control is still ineffective when it is close to the machine, replace it with a new
battery.
If the user does not use the remote control for a long time, remove the battery of the remote
control.
Dispose of used batteries in accordance with local regulations on battery disposal.
Operating the remote
control
This remote controller use 2 x R03/AAA batteries.
Remote control
Power ON/OFF
Input select
Menu/OK button
Next level menu
Return
Mute
Volume +
D
own
Up
FN(Define in the menu)
Volume -
Display Interface and Instructions
1 x SMSL DO400 1 x Remote control 1 x Bluetooth antenna
1 x USB cable 1 x AC power cable 1 x User manual
1 x Warranty card
XLR output
USB input
5 6
RCA output 9
7
Optical input
8
6.35mm headphone jack4.4mm headphone jack
Coaxial input
1 2 3
4
Bluetooth antenna
Balanced headphone jack
10 AES/EBU input 12
11 I2S input
13 15
14
Display screen Indicator lightInfrared receiving window
Function knob
AC IN
16
Package list
41 2 3 5 67
10
9
15 16
14
13
1211
8
PRE MODE
PRE MODE is the volume adjustment function
switchfor the output interface.
VARIABLE: The output interface volume is controlled.
FIXED: The output interface volume is fixed.
Instructions
There are 4 kinds of digital filtering in total. It's the way
that the digital operation means the clutter outside the
audioFilter out, respectively
DSD FILTER
INPUTS
USB
BLUETOOTH
OPTICAL
COAXIAL
AES/EBU
I2S(HDMI)
PCM FILTER
FILTER OFF
MINIMUM PHASE
APODIZING
LINEAR FAST
LINEAR SLOW
MINIMUM FAST
MINIMUM SLOW
LOW DISPERSION
HPA GAIN
LOW
HIGH
OUTPUTS
ALL LINE OUT
HEADPHONE OUT
BALANCED
UNBALANCED
47kHz Cutoff
50kHz Cutoff
60kHz Cutoff
70kHz Cutoff
Instructions
DPLL
MIN ~ MAX
(A total of 15 kinds, the default is 7 kinds. The larger the number is, the stronger the range to adapt to jitter, and the
smaller the number, the better the performance against clock jitter.)
This DPLL setting is a special function of ESS series products. It can adjust the internal DPLL digital phase locked
loop circuit Bandwidth, so that the chip achieves a balance between anti clock jitter and input tolerance.
Its function:
When the clock stability of the input signal is good, this value can be reduced, so that the clock performance
of the system is better;
When the clock stability of the input signal is not good, the sound may be interrupted. Increase this value
can avoid the sound interruption! Especially when using TV as signal source!
FN KEY FOR
SWITCH LINE/HPA
BLUETOOTH
This machine has a total of 9 tone modes, which are processed by DSP through DAC, which are:
Rich1, Rich2, Rich3
Tube1, Tube2, Tube3
Crystal1, Crystal2, Crystal3
This setting is usingthe DSP of DAC, to make some different sound color, all of these settings will not change
the frequency res ponse curve.When set to "Standard", this setting will be bypassed.
SOUND COLOR
OUTPUTS
PHASE
Instructions
AUDIO PHASE
NORMAL (2+,3-)
1 2-
3+
INVERTED
1 2+
3-
NORMAL
INVERTED (2-,3+)
I2S MODE
NORMAL
Note: This option is used to match different I2S interface standards, please check the interface
definition of the signal source before use
I2S D ATA +
I2S D ATA -
I2S LRCLK +
I2S LRCLK -
GND
NC
DSD FLAG
NC
GND
GND
GND
GND
I2S MCLK +
I2S MCLK -
NC
MUTE
NC
I2S BCK +
I2S BCK -
21
18
19
REVERSED NORMAL
GND
GND
I2S MCLK +
I2S MCLK -
NC
MUTE
NC
I2S BCK +
I2S BCK -
I2S D ATA -
I2S D ATA +
I2S LRCLK -
I2S LRCLK +
GND
NC
DSD FLAG
NC
GND
GND
21
18
19
REVERSED
/