Dell PowerEdge C2100 ユーザーガイド

タイプ
ユーザーガイド

Dell PowerEdge C2100 は、メモリを最大 288 GB まで搭載でき、大規模なデータベースや仮想化環境にも対応するパワフルなサーバーです。また、ホットスワップ対応の最大 24 個の 2.5 インチ SAS/SATA ハードドライブを搭載できるので、データの保存やアクセスも高速に行えます。さらに、最大 2 個の 2.5 インチ SATA/SSD ハードドライブを搭載することもでき、高速なストレージが必要なアプリケーションにも最適です。

Dell PowerEdge C2100 は、拡張性にも優れており、PCIe x8 スロットと PCIe x4 カスタムスロットを 2 つずつ備えています。これにより、ネットワークカードやストレージコントローラなどのさまざまな拡張カードを追加することができ、システムの機能を拡張することができます。

また、Dell PowerEdge C2100 は、管理が容易なことも特徴です。専用の iDRAC9

Dell PowerEdge C2100 は、メモリを最大 288 GB まで搭載でき、大規模なデータベースや仮想化環境にも対応するパワフルなサーバーです。また、ホットスワップ対応の最大 24 個の 2.5 インチ SAS/SATA ハードドライブを搭載できるので、データの保存やアクセスも高速に行えます。さらに、最大 2 個の 2.5 インチ SATA/SSD ハードドライブを搭載することもでき、高速なストレージが必要なアプリケーションにも最適です。

Dell PowerEdge C2100 は、拡張性にも優れており、PCIe x8 スロットと PCIe x4 カスタムスロットを 2 つずつ備えています。これにより、ネットワークカードやストレージコントローラなどのさまざまな拡張カードを追加することができ、システムの機能を拡張することができます。

また、Dell PowerEdge C2100 は、管理が容易なことも特徴です。専用の iDRAC9

Dell™ PowerEdge™ C2100
Getting Started
With Your System
系统使用入门
Memulai Pengaktifan dengan Sistem
はじめに
시스템 시작 안내서
Dell PowerEdge C2100
Getting Started
With Your System
Regulatory Model FS12-TY
Notes, Cautions, and Warnings
NOTE:
A NOTE indicates important information that helps you make better use of
your computer.
CAUTION:
A CAUTION indicates potential damage to hardware or loss of data
if instructions are not followed.
WARNING:
A WARNING indicates a potential for property damage, personal
injury, or death.
____________________
© 2013 Dell Inc. All rights reserved.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge, are trademarks of Dell Inc.;
Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its subsidiaries, and may
be registered in the United States Patent and Trademark Office and in other countries; Intel and Xeon
are registered trademarks of Intel Corporation in the U.S. and other countries; VMware is a registered
trademark of VMware, Inc. in the United States and/or other jurisdictions; Red Hat and Red Hat
Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States and other countries;
SUSE is a registered trademark of Novell, Inc. in the United States and other countries.
Regulatory Model FS12-TY
2013 - 11 P/N 70WC0 Rev. A02
Getting Started With Your System
3
Installation and Configuration
WARNING:
Before performing the following procedure, review the safety
instructions that came with the system.
Unpacking the System
Unpack your system and identify each item.
Installing the Rails and System in a Rack
WARNING:
Whenever you need to lift the system, get others to assist you.
To avoid injury, do not attempt to lift the system by yourself.
WARNING:
The system is not fixed to the rack or mounted on the rails. To avoid
personal injury or damage to the system, you must adequately support the system
rack during installation and removal.
CAUTION:
Before installing systems in a rack, install front and side stabilizers
on stand-alone (single) racks or the front stabilizer on racks joined to other racks.
Failure to install stabilizers accordingly before installing systems in a rack could
cause the rack to tip over, potentially resulting in bodily injury under certain
circumstances. Therefore, always install the stabilizer(s) before installing
components in the rack.
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by Dell is not
covered by your warranty. Read and follow the safety instructions that came
with the product.
4
Getting Started With Your System
1
Secure the rails to the front of the rack using two screws and to the back of
the rack using four screws.
2
Align the keyhole slot on the chassis rails with the corresponding pin
on either side of the system and slide the chassis rails towards the front
of the system until it locks into place. Secure the chassis rails to the
system using screws.
Getting Started With Your System
5
3
Align and insert the ends of the chassis rails into the ends of the rails and
push the system inward until the chassis rails lock into place.
4
Tighten the thumbscrews to secure the ears of system to the rack.
6
Getting Started With Your System
Optional – Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable
to plug into each connector. Be sure to tighten the screws (if any) on the
monitor's cable connector.
Connecting the Power Cable(s)
Getting Started With Your System
7
Connect the system’s power cable(s) to the system and, if a monitor is used,
connect the monitor’s power cable to the monitor. Plug the other end of the
power cables into a grounded electrical outlet or a separate power source such
as an uninterrupted power supply (UPS) or a power distribution unit (PDU).
Turning On the System
Press the power button on the system and the monitor. The power indicators
should light.
Complete the Operating System Setup
To install an operating system, see the installation and configuration
documentation for your operating system. Be sure the operating
system is installed before installing hardware or software not purchased
with the system.
8
Getting Started With Your System
Supported Operating Systems
•Red Hat
®
Enterprise Linux
®
5.4 Standard edition (x64)
Red Hat Enterprise Linux 5.4 Standard edition (x86)
•SUSE
®
Linux Enterprise Server 11 (x86_64)
Citrix
®
XenServer™ Enterprise edition 5.
x
VMware
®
ESX Server Version 4.0, Update 1
NOTE:
For the latest information on supported operating systems,
see dell.com/ossupport.
Other Information You May Need
WARNING:
See the safety and regulatory information that shipped with
your system. Warranty information may be included within this document or
as a separate document.
•The
Hardware Owner’s Manual
provides information about system
features and describes how to troubleshoot the system and install or
replace system components. This document is available online at
dell.com/support/manuals
.
Dell systems management application documentation provides
information about installing and using the systems management software.
This document is available online at
dell.com/support/manuals
.
NOTE:
Always check for updates on dell.com/support/manuals and read
the updates first because they often supersede information in other documents.
Getting Started With Your System
9
NOM Information (Mexico Only)
The following information is provided on the device described in this
document in compliance with the requirements of the official Mexican
standards (NOM):
Technical Specifications
Importer:
Model number: FS12-TY
Supply voltage: 100–240 V CA
Frequency: 50/60 Hz
Current consumption: 9.0–5.0 A
Processor
Processor type One or two Intel
®
Xeon
®
5500 or 5600 series
processors (up to six core processors)
Expansion Bus
Bus type PCI Express Generation 2
Expansion slots
PCIe
Two x8 half-length, full height
Mezzanine slots
PCIe
Two x4 custom slots
Memory
Architecture 800/1066/1333 MHz DDR-3
unbuffered/registered memory modules with
Error Correcting Code (ECC)
Memory module sockets Eighteen 240-pin DIMMs
Memory module capacities 2 GB, 4 GB, 8 GB, or 16 GB
10
Getting Started With Your System
Minimum RAM 12 GB RAM
Maximum RAM 144 GB (dual rank) using 8 GB DIMM
288 GB (quad rank) using 16 GB DIMM
S3 Sleep State
48 GB using 2 GB or 4 GB DIMM
Drive
Hard drives Up to twelve 3.5", hot-swappable SAS/SATA
hard drives
Up to twenty four 2.5", hot-swappable
SAS/SATA hard drives (when available)
(Optional) up to two 2.5", internal SATA/SSD
hard drives (when available)
Connectors
Back
NIC
Two RJ-45 (for integrated 10/100/1000 Mbps
Ethernet)
KVM over IP port
Dedicated Ethernet port for remote
management access
Serial
9-pin, DTE, 16550-compatible
USB
Two 4-pin, USB 2.0-compliant
Video
15-pin VGA
Video
Video type AST2050 video controller; VGA connector
Video memory 8 MB
Memory (continued)
Getting Started With Your System
11
Power
AC power supply (redundant)
Wattage 750 W
Voltage
100–240 VAC, 50/60 Hz, 9.5–5.0 A
Heat dissipation
2217.8 BTU/hr maximum
Maximum inrush current
Under typical line conditions and over
the entire system ambient operating range,
the inrush current may reach 55 A per power
supply for 10 ms or less.
Batteries
System battery
CR 2032 3.0-V Lithium coin cell
ROMB battery (optional)
3.7-V Lithium ion battery pack
Physical
Height 87.5 cm (3.44")
Width 43.74 cm (17.22")
Depth 72.2 cm (28.42")
Weight (maximum configuration) 28.5 kg (62.8 lb)
Weight (empty) 12 kg (26.5 lb)
Environmental
For additional information about environmental measurements for specific system
configurations, see www.dell.com/environmental_datasheets.
Temperature
Operating
10° to 35°C (50° to 95°F) with a maximum
temperature gradation of 10°C per hour
NOTE:
For altitudes above 2950 ft,
the maximum operating temperature
is derated 1ºF/550 ft.
Storage
–40° to 65°C (–40° to 149°F) with
a maximum temperature gradation
of 20°C per hour
12
Getting Started With Your System
Relative humidity
Operating
8% to 85% (noncondensing) with a maximum
humidity gradation of 10% per hour
Storage
5% to 95% (noncondensing)
Maximum vibration
Operating
0.26 Grms at 5–350 Hz
Storage
1.54 Grms at 10–250 Hz for 15 mins
Maximum shock
Operating
One shock pulse in the positive z axis
(one pulse on each side of the system)
of 31 G for 2.6 ms in the operational
orientation
Storage
Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system)
of 71 G for up to 2 ms
Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system) of
27 G fair squared wave pulse with velocity
at 596.9 cm/sec
Altitude
Operating
–16 to 3048 m (–50 to 10,000 ft)
NOTE:
For altitudes above 2950 ft,
the maximum operating temperature
is derated 1ºF/550 ft.
Storage
–16 to 12,000 m (–50 to 35,000 ft)
Airborne Contaminant Level
Class
G2 or lower as defined by ISA-S71.04-1985
Environmental (continued)
Dell PowerEdge C2100
系统使用入门
管制型号 FS12-TY
注、小心和警告
注:
“注”表示可以帮助您更好地使用计算机的重要信息。
小心:
“小心”表示如果不遵循说明,就有可能损坏硬件或导致数据丢失。
警告:
“警告”表示可能会导致财产损失、人身伤害甚至 死亡。
____________________
© 2013 Dell Inc. 保留所有权利。
本文中使用的商标 DellDELL 徽标、 PowerEdge Dell Inc. 的商标; Citrix XenServer
Citrix Systems, Inc. / 或其一个或多个子公司的商标,并且可能在美国商标局和其他国家
/ 地区进行了注册; Intel Xeon Intel Corporation 在美国 和其他国家 / 地区的注册商标;
VMware VMware, Inc. 在美国和 / 或其他辖区的注册商标; Red Hat Red Hat Enterprise
Linux Red Hat, Inc. 在美国和其他国家 / 地区的注册商标; SUSE Novell, Inc. 在美国和其
他国家 / 地区的注册商标。
管制型号 FS12-TY
2013 - 11 P/N 70WC0 Rev. A02
系统使用入门
15
安装和配置
警告:
执行下列步骤之前,请查看系统随附的安全说明。
打开系统包装
打开系统包装并检查各个组件。
在机架中安装滑轨和系统
警告:
如需抬高系统时,请让别人帮您。为避免受伤,请勿尝试独自提起
系统。
警告:
系统未固定到机架上或未安装在导轨上。为避免人身伤害或损坏系
统,在安装和拆卸过程中必须充分支撑系统机架。
小心:
在机架上安装系统之前,对于独立 (单个)机架,请先安装正面和
侧面支脚;对于与其它机架合并在一起的机架,请先安装正面支脚。如果在
安装系统之前,没有给机架安装相应的支脚,则在某些情况下,机架可能会
翻倒,导致人员受伤。因此,在机架上安装组件之前,请务必先安装支脚。
小心:
多数维修只能由经认证的维修技术人员进行。您只能根据产品说明
文件中的授权,或者在联机或电话服务和支持小组的指导下,进行故障排除
和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围之内。请阅
读并遵循产品附带的安全说明。
16
系统使用入门
1 用两颗螺钉将导轨固定到机架正面,用四颗螺钉将导轨固定到机架
背面。
2
将机箱导轨上的锁孔槽分别对准系统两边的相应销,然后将机箱导轨
滑向系统前端,直至其锁入到位。使用螺钉将机箱导轨固定在系统上。
系统使用入门
17
3
将机箱导轨末端对准导轨末端并插入,然后将系统往内推,直至机箱
导轨锁入到位。
4
拧紧指旋螺钉,将系统吊耳固定到机架上。
18
系统使用入门
可选 连接键盘、鼠标和显示器
连接键盘、鼠标和显示器 (可选)
系统背面的连接器附有图标,指示要插入每个连接器的电缆。请确保拧紧
显示器电缆连接器上的螺钉 (如果有)
连接电源电缆
将系统电源电缆连接至系统,如果使用显示器,则将显示器电源电缆连接
至显示器。将电源电缆的另一端插入接地的电源插座或单独的电源,如不
间断电源设备 (UPS) 或配电装置 (PDU)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Dell PowerEdge C2100 ユーザーガイド

タイプ
ユーザーガイド

Dell PowerEdge C2100 は、メモリを最大 288 GB まで搭載でき、大規模なデータベースや仮想化環境にも対応するパワフルなサーバーです。また、ホットスワップ対応の最大 24 個の 2.5 インチ SAS/SATA ハードドライブを搭載できるので、データの保存やアクセスも高速に行えます。さらに、最大 2 個の 2.5 インチ SATA/SSD ハードドライブを搭載することもでき、高速なストレージが必要なアプリケーションにも最適です。

Dell PowerEdge C2100 は、拡張性にも優れており、PCIe x8 スロットと PCIe x4 カスタムスロットを 2 つずつ備えています。これにより、ネットワークカードやストレージコントローラなどのさまざまな拡張カードを追加することができ、システムの機能を拡張することができます。

また、Dell PowerEdge C2100 は、管理が容易なことも特徴です。専用の iDRAC9

他の言語で