Dell PowerEdge 2950 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2950 Systems

Getting Started

With Your System

系统使用入门

はじめに

시스템시작하기

Model EMS01

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2950 Systems

Getting Started With

Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Intel and Xeon are registered trademarks of Intel Corporation;

Microsoft and Windows are registered trademarks and Windows Server is a trademark of Microsoft Corporation; Novell and NetWare are

registered trademarks of Novell, Inc.; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark of SUSE LINUX

Products GmbH.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model EMS01

November 2005 P/N DD247 Rev. A00

Getting Started With Your System 3

System Features

The major hardware and software features of your system include:

• One or two Dual-Core Intel

®

Xeon

®

Processors 5000 Sequence.

• Support for symmetric multiprocessing (SMP), which is available on systems with two Intel Xeon

processors. SMP greatly improves overall system performance by dividing processor operations

between independent processors. To take advantage of this feature, you must use an operating

system that supports multiprocessing.

NOTE: If you decide to upgrade your system by installing a second processor, you must order the

processor upgrade kits from Dell. Not all versions of the Intel Xeon processor will work properly as

additional processors. The upgrade kit from Dell contains the correct version of the processor, heat sink,

and fan as well as the instructions for performing the upgrade.

• A minimum of 512 MB of 533 or 667 (when available) MHz, Fully Buffered DIMMs (FBD),

upgradable to a maximum of 32 GB by installing combinations of 256-MB, 512-MB, 1-GB, 2-GB,

or 4-GB memory modules in the eight memory module sockets on the system board.

The system also features redundant memory, which provides memory sparing or memory

mirroring. Either feature is available if eight identical memory modules are installed.

• Support for up to six 3.5-inch, internal hot-pluggable Serial Attached SCSI (SAS) or SATA hard

drives without optional media bay, or up to four 3.5-inch internal hot-pluggable SAS or SATA hard

drives with optional media bay, or eight 2.5-inch internal hot-pluggable SAS hard drives.

• The optional media bay (available with the 3.5-inch x4 and 2.5-inch x8 backplane configurations)

provides support for an optional half-height tape backup unit (TBU) and an optional single,

1.44-MB, 3.5-inch diskette drive.

• An optional slim-line IDE CD, DVD, or combination CD-RW/DVD drive.

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management software if the top cover is

opened.

• Up to two hot-pluggable, 750-W power supplies in an optional 1 + 1 redundant configuration.

• Four hot-pluggable system cooling fans.

4 Getting Started With Your System

The system board includes the following features:

• One of the following left riser card options:

– A left riser card that has one full-length PCIe x8 lane slot and one full-length PCIe x4 lane slot.

OR

– A left riser card that has two full-length PCI-X 3.3-V, 64-bit,133-MHz slots on separate PCI-X buses

(capable of throttling back to support legacy PCI add-in cards).

• A center riser card that has one half-length PCIe x8 lane slot.

• Dedicated slot for an integrated SAS host bus adapter or an optional RAID controller card with

256 MB of cache memory and a RAID battery. The internal channel supports up to eight 2.5-inch SAS

or six 3.5-inch SATA hard drives.

NOTE: System boot is not supported from an external device attached to a SAS or SCSI adapter, including

SAS 5/E, PERC 5/E, or PERC 4e/DC. See support.dell.com for the latest support information about booting

from external devices.

• Two integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps

data rates.

• Four USB 2.0-compliant connectors (two on the front and two on the back) capable of supporting

a diskette drive, a CD-ROM drive, a keyboard, a mouse, or a USB flash drive.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz PCI video controller.

This video subsystem contains 16 MB of DDR SDRAM video memory (nonupgradable). Maximum

resolution is 1600 x 1200 with 64 K colors; true-color graphics are supported in the following

resolutions: 640 x 480, 800 x 600, 1024 x 768, 1152 x 864, and 1280 x 1024. When the optional RAC

is installed, the video resolution is 1280 X 1024.

• Systems management circuitry that monitors operation of the system fans as well as critical system

voltages and temperatures. The systems management circuitry works in conjunction with the systems

management software.

• Standard baseboard management controller with serial access.

• Back-panel connectors include one serial, one video, two USB, and two NIC connectors.

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see "Technical Specifications" on page 10.

Getting Started With Your System 5

Supported Operating Systems

• Microsoft

®

Windows Server

™

2003 Standard, Enterprise, and Web Editions

• Microsoft Windows Server 2003 Standard and Enterprise x64 Editions

•Red Hat

®

Enterprise Linux AS and ES for Intel x86 (versions 3 and 4)

• Red Hat Enterprise Linux AS and ES for Intel Extended Memory 64 Technology (Intel EM64T)

(version 4)

•SUSE

®

Linux Enterprise Server 9 for Intel EM64T

•Novell

®

NetWare

®

6.5 (when available) (not available factory-installed)

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty

information may be included within this document or as a separate document.

• The

Rack Installation Instructions

or

Rack Installation Guide

included with your rack solution

describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system features and describes how to

troubleshoot the system and install or replace system components. This document may be found on

the CDs that came with your system, or on

support.dell.com

.

• CDs included with your system provide documentation and tools for configuring and managing your

system.

• Release notes or readme files may be included to provide last-minute updates to the system or

documentation or advanced technical reference material intended for experienced users or

technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected, see

your Hardware Owner’s Manual.

Dell™ Enterprise Training and Certification is available; see www.dell.com/training for more

information. This service may not be offered in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

6 Getting Started With Your System

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack installation documentation

for your system, install the rails and the system in the rack.

See your rack installation documentation for instructions on installing your system in a rack.

Getting Started With Your System 7

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into each

connector. Be sure to tighten the screws (if any) on the monitor's cable connector.

Connecting the Power

Connect the monitor (optional) and system power, and connect the system’s power cable(s) to

the system. If your system has an expansion card with a video output connector,

do not

connect

the monitor to system’s integrated video connector. Instead, connect the monitor cable to the

connector on the expansion card.

Plug the other end of the cable into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

8 Getting Started With Your System

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power supply handle. Bend the

system power cable into a loop as shown in the illustration and attach to the bracket’s cable clasp.

Repeat the procedure for the second power supply.

Plug the other end of the power cables into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators should light.

Adjust the monitor's controls until the displayed image is satisfactory.

Getting Started With Your System 9

Installing the Bezel

Install the bezel (optional).

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships

with your system. To install an operating system for the first time, see the Quick Installation Guide.

Be sure the operating system is installed before installing hardware or software not purchased with

the system.

10 Getting Started With Your System

Technical Specifications

Processor

Processor type One or two Dual-Core Intel Xeon Processors 5000

Sequence.

Expansion Bus

Bus type PCI-X, PCIe

Expansion slots

Center riser:

PCIe

one half-height x8 lane 3.3-V (slot 1)

Left riser

PCI-X option:

PCIe option:

two full-height, full-length 3.3-V, 64-bit, 133-MHz

(slots 2 and 3)

OR

one full-height x8 lane 3.3-V (slot 2) and one full-

height x4 lane 3.3-V (slot 3)

Memory

Architecture 533 or 667 (when available) MHz Fully Buffered

DIMMs (FBD)

Memory module sockets eight 240-pin

Memory module capacities 256 MB, 512 MB, 1 GB, 2 GB, or 4 GB

Minimum RAM 512 MB (two 256-MB modules)

Maximum RAM 32 GB

Drives

Hard drives up to six 3.5-inch, internal hot-pluggable SAS

or SATA hard drives without optional media bay,

OR

up to four 3.5-inch internal hot-pluggable SAS

or SATA hard drives with optional media bay

OR

eight 2.5-inch internal hot-pluggable SAS hard

drives

Diskette drive one optional 3.5-inch, 1.44-MB

external optional USB 3.5-inch, 1.44-MB

Getting Started With Your System 11

Optical drive one optional slimline IDE CD, DVD,

or combination CD-RW/DVD

NOTE:

DVD devices are data only.

external optional USB CD

Tape drive one optional internal half height tape backup

device

Flash drive external optional USB

Connectors

Back

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Video

Video type ATI ES1000 video controller; VGA connectors

Video memory 16 MB of DDR SDRAM

Power

AC power supply (per power supply)

Wattage

750 W

Voltage

85–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply for

10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Drives (continued)

12 Getting Started With Your System

Physical

Rack

Height

8.656 cm (3.40 in)

Width

44.7 cm (17.6 in)

Depth

75.68 cm (29.79 in)

Weight (maximum configuration)

26.76 kg (59 lb)

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets.

Temperatur e

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing) with a maximum

humidity gradation of 10% per hour

Maximum vibration

Operating

0.25 G at 3–200 Hz for 15 min

Storage

0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2950 系统

系统使用入门

注、注意和警告

注：注表示可以帮助您更好地使用计算机的重要信息。

注意：

注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：

警告表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

和

DELL

徽标是

Dell Inc.

的商标；

Intel

和

Xeon

是

Intel Corporation

的注册商标；

Microsoft

和

Windows

是

Microsoft Corporation

的注册商标，

Windows Server

是

Microsoft Corporation

的商标；

Novell

和

NetWare

是

Novell, Inc.

的注册

商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

SUSE LINUX Products GmbH

的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外

的其它商标和产品名称不拥有任何专有权。

型号

EMS01

2005

年

11

月

P/N DD247

修订版

A00

系统使用入门 15

系统配置

系统的主要硬件和软件配置包括：

• 一个或两个双核心

Intel

®

Xeon

®

处理器

5000

序列。

• 支持对称多处理

(SMP)

，配备两个

Intel Xeon

处理器的系统具有此功能。

SMP

通过在独立

的处理器之间分配处理器操作，从而极大地改善了整体的系统性能。要使用此功能，必须

使用支持多处理的操作系统。

注：如果您准备安装第二个处理器来升级系统，则必须向 Dell 订购处理器升级套件。并非所有

版本的 Intel Xeon 处理器均可作为附加处理器正常工作。Dell 的升级套件包含正确版本的处理

器、散热器和风扇，以及执行升级的说明。

• 至少

512 MB

的

533

或

667

（可用时）

MHz

全缓冲

DIMM (FBD)

，通过在系统板上的八个

内存模块插槽中安装

256 MB

、

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块组合，最大可升级

至

32 GB

。

系统还配置了冗余内存，可提供内存冗余或内存镜像功能。如果安装了八个完全相同的内

存模块，则同时提供内存冗余或内存镜像功能。

• 支持多达六个

3.5

英寸、内部热插拔、串行连接的

SCSI (SAS)

或

SATA

且未配备可选介质

托架的硬盘驱动器，或支持多达四个

3.5

英寸、内部热插拔

SAS

或

SATA

且配备了可选介

质托架的硬盘驱动器，或八个

2.5

英寸内部热插拔

SAS

硬盘驱动器。

• 可选介质托盘（可提供

3.5

英寸

x4

和

2.5

英寸

x8

的背板配置）支持一个可选半高磁带备

份装置

(TBU)

和一个可选

1.44 MB

、

3.5

英寸软盘驱动器。

• 一个可选的细长型

IDE CD

、

DVD

或组合

CD-RW/DVD

驱动器。

注：DVD 设备仅用于数据。

• 防盗开关，在顶盖被打开时会向相应的系统管理软件发送信号。

• 多达两个

750 W

热插拔电源设备（可选

1 + 1

冗余配置）。

• 四个热插拔系统冷却风扇。

系统板包含以下配置：

• 以下左提升卡选件之一：

- 具有一个全长

PCIe x8

信道插槽和一个全长

PCIe x4

信道插槽的左提升卡。

或

- 在单独的

PCI-X

总线上具有两个全长

PCI-X 3.3 V

、

64

位、

133 MHz

插槽的左提升卡

（能够节流以支持传统的内插式

PCI

卡）。

• 具有一个半长

PCIe x8

信道插槽的中心提升卡。

16 系统使用入门

• 专用插槽，用于安装集成的

SAS

主机总线适配器或配有

256 MB

高速缓存和

RAID

电池的可选

RAID

控制器卡。内部信道支持多达八个

2.5

英寸

SAS

硬盘驱动器或六个

3.5

英寸

SATA

硬盘

驱动器。

注：不支持从连接到 SAS 或 SCSI 适配器的外部设备引导系统，包括 SAS 5/E、PERC 5/E 或 PERC

4e/DC。有关支持从外部设备引导的最新信息，请参阅 support.dell.com。

• 两个集成的千兆位以太网

NIC

，可支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

• 四个

USB 2.0

兼容连接器（两个在正面，两个在背面），可以支持软盘驱动器、

CD-ROM

驱动器、键盘、鼠标或

USB

快擦写驱动器。

• 可选的远程访问控制器

(RAC)

，用于远程系统管理。

•

VGA

兼容集成视频子系统，带有

ATI ES1000

、

33 MHz PCI

视频控制器。此视频子系统包含

16 MB

的

DDR SDRAM

视频内存（不可升级）。使用

64 K

色时最大分辨率为

1600 x 1200

；

以下分辨率支持真彩色图形：

640 x 480

、

800 x 600

、

1024 x 768

、

1152 x 864

和

1280 x 1024

。

如果安装了可选的

RAC

，则视频分辨率为

1280 x 1024

。

• 系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。系统管理电路需要与系统管

理软件配合工作。

• 标准底板管理控制器，支持串行访问。

• 背面板连接器包括一个串行连接器、一个视频连接器、两个

USB

连接器和两个

NIC

连接器。

• 前面板连接器包括一个视频连接器和两个

USB

连接器。

• 前面板

1x5 LCD

显示屏，用于显示系统

ID

和错误信息。

• 系统

ID

按钮，位于前面板和背面板上。

有关特定配置的详细信息，请参阅第

22

页的“技术规格”。

支持的操作系统

•

Microsoft

®

Windows Server

™

2003

标准版、企业版和

Web

版

•

Microsoft Windows Server 2003

标准版和企业版（

64

位）

• 用于

Intel x86

的

Red Hat

®

Enterprise Linux AS

和

ES

（第

3

版和第

4

版）

• 用于

Intel 64

位扩展内存技术

(Intel EM64T)

的

Red Hat Enterprise Linux AS

和

ES

（第

4

版）

• 用于

Intel EM64T

的

SUSE

®

Linux Enterprise Server 9

•

Novell

®

NetWare

®

6.5

（可用时）（非工厂安装）

系统使用入门 17

您可能需要的其它信息

警告：

《产品信息指南》，提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

• 随机架解决方案附带的《机架安装说明》或《机架安装指南》，介绍了如何在机架中安装系

统。

• 《硬件用户手册》提供有关系统部件的信息，并介绍如何排除系统故障以及如何安装或更换系

统组件。此说明文件可在随系统提供的

CD

中找到，或通过

support.dell.com

获得。

• 随系统附带的

CD

提供了用于配置和管理系统的说明文件和工具。

• 系统可能附带发布注释或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的

用户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的步骤有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

Della

可以提供企业培训与认证；有关详情，请访问

www.dell.com/training

。并非在所有国家和地区

均可提供此服务。

安装和配置

警告：

在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。

18 系统使用入门

打开系统包装

打开系统包装并识别每项物品。

妥善保管所有运输包装材料，以备将来使用。

在机架中安装滑轨和系统

在仔细阅读了系统的机架安装说明文件中的“安全说明”之后，在机架中安装滑轨和系统。

有关在机架中安装系统的说明，请参阅机架安装说明文件。

ページを読み込んでいます...

Dell PowerEdge 2950 クイックスタートガイド

関連論文

その他の書類