ICP WISE-5800-MTCP クイックスタートガイド

WISE-580x Quick Start Guide

1

Quick Start Guide for

WISE-580x Series

May 2012, Version 1.2

Thank you for purchasing WISE-580x – the Intelligent Data Logger PAC controller

for remote monitoring and control application. This Quick Start Guide will provide

you with minimum information to get started with WISE-580x. It is intended for use

only as a quick reference. For more detailed information and procedures, please

refer to the full user manual on the CD included in this package.

In addition to this guide, the package includes the following items:

WISE-580x

Series Module

Software

Utility CD

2G microSD

card

RS-232 cable

(CA-0910)

Screw Driver

(1C016)

GSM Antenna

(ANT-421-02)

Only for WISE-5801

 WISE-580x User Manual

CD:\WISE-580x\document\User Manual\

http://ftp.icpdas.com/pub/cd/wise_cd/wise-580x/document/user manual/

 WISE Website

http://wise.icpdas.com/index.html

 ICP DAS Website

http://www.icpdas.com/

WISE-580x Quick Start Guide

2

1

--------------------------------------------

Configuring Boot Mode

Make sure the “Lock“ switch placed in the “OFF”

position, and the “Init’ switch placed in the “OFF”

position.

2

---------------------------------------------------------------------

Connecting to PC, Network and Power

The WISE-580x is equipped with an RJ-45 Ethernet port for connection to an

Ethernet hub/switch and PC. You can also link directly the WISE-580x to PC with an

Ethernet cable.

WISE-580x

+Vs

+

WISE-580x Quick Start Guide

3

-----------------------------------------------------

Installing the MiniOS7 Utility

Step 1: Get the MiniOS7 Utility

The MiniOS7 Utility can be obtained from companion CD or our FTP site:

CD:\Tools\MiniOS7 Utility\

ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/minios7_utility/

Please download version v3.2.4 or later.

Step 2: Follow the prompts to complete the installation

After the installation has been completed,

there will be a new short-cut for MiniOS7

Utility on the desktop.

4

-------------------------------------------------------------------------

Using MiniOS7 Utility to Assign a New IP

The WISE-580x is an Ethernet device, which comes with a default IP address,

therefore, you must first assign a new IP address to the WISE-580x.

The factory default IP settings are as follows:

Item

Default

IP Address

192.168.255.1

Subnet Mask

255.255.0.0

Gateway

192.168.0.1

MiniOS7 Utility Ver 3.24

WISE-580x Quick Start Guide

4

Step 1: Run the MiniOS7 Utility

Double-click the MiniOS7 Utility shortcut on your

desktop.

Step 2: Press “F12” or choose “Search” from the “Connection” menu

After pressing F12 or choosing “Search” from “Connection” menu, the MiniOS7

Scan dialog will appear, that will display a list of all the MiniOS7 modules on your

network.

See the status tip, waiting

for the search to be done.

WISE-580x Quick Start Guide

5

Step 3: Choose the module name and then choose “IP setting” from the

toolbar

Choose the module name for fields in the list, and then choose IP setting from the

toolbar.

Step 4: Assign a new IP address and then choose “Set” button

Step 5: Choose “Yes” button &

Reboot WISE-580x

After completing the settings, press the Yes

button in the Confirm dialog box to exit the

procedure, then reboot WISE-580x..

WISE-580x Quick Start Guide

6

5

----------------------------------------------------------------------------------

Go to WISE-580x Web Site to edit Control Logic

Please follow the steps below to implement IF-THEN-ELSE control logic on

controllers:

Step 1: Open a browser, and type in the URL address of the WISE-580x

Open a browser (recommended using Internet Explorer, new version is better). Type in

the URL address of the WISE-580x module in the address bar. Make sure the IP

address is accurate.

Step2: Get on the WISE-580x web site

Get on the WISE-580x web site.

Login with the default password

“wise”. Implement the control logic

configuration in the order (Basic

SettingAdvanced SettingRule

SettingDownload to Module), then

complete the IF-THEN-ELSE rule

editing.

.

Step 3: For more detail information, please refer to WISE User Manual

WISE-580x 快速安裝指南

1

WISE-580x 系列快速安裝指南

May 2012, Version 1.2

歡迎使用 WISE-580x 快速安裝指南

感謝您購買 WISE-580x系列控制器：多功能智慧型資料記錄(Data Logger)

PAC控制器。本『快速安裝指南』提供 WISE-580x系列安裝入門所需資訊, 如

需更詳細的安裝及使用說明, 請參閱更完整的使用手冊。

產品內容

除了本『快速安裝指南』外, 此產品內容還包括以下配件:

技術支援

 WISE-580x User Manual

CD:\WISE-580x\document\User Manual\

http://ftp.icpdas.com/pub/cd/wise_cd/wise-580x/document/user manual/

 WISE Website

http://wise.icpdas.com/big5/index.html

 ICP DAS Website

http://www.icpdas.com/

WISE-580x

模組

軟體工具

光碟

2G microSD

記憶卡

RS-232 纜線

(CA-0910)

螺絲起子

(1C016)

GSM 天線

(ANT-421-02)

僅提供 WISE-5801

WISE-580x 快速安裝指南

2

1

--------------------------------------------

檢視啟動模式

確認指撥開關 Lock 的位置在 ”OFF”，Init

的位置在“OFF”。

2

---------------------------------------------

連接主機、網路及電源

WISE-580x 系列配有標準的網路接口 RJ-45，可透過網路集線器/交換器與 PC

連接, 也可直接連到 PC 的網路接口。

WISE-580x

+Vs

+

WISE-580x 快速安裝指南

3

---------------------------------------

安裝

MiniOS7 Utility

步驟一: 取得 MiniOS7 Utility

MiniOS7 Utility 可取自隨附的光碟或 FTP:

CD:\Tools\MiniOS7 Utility\

ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/minios7_utility/

請下載 v3.2.4 以後的版本。

步驟二: 按照命令提示完成安裝

安裝完成後, 桌面上將會出現

MiniOS7 Utility 的捷徑圖示

4

-----------------------------------------------------------

啟動

MiniOS7 Utility

設定

IP

位址

WISE-580x 系列模組在出廠時會統一預設網路設定值，使用者可以依照下列

步驟自行變更網路設定。WISE 模組的網路出廠預設值:

項目

預設值

IP 位址

192.168.255.1

子網路遮罩 (subnet mask)

255.255.0.0

通訊閘 (gateway)

192.168.0.1

MiniOS7 Utility Ver 3.24

WISE-580x 快速安裝指南

4

步驟一: 啟動 MiniOS7 Utility

雙擊MiniOS7 Utility

桌面捷徑

步驟二: 選取鍵盤 “F12” 或於 “Connection” 選單中選取 “Search”

選取鍵盤 F12 或於 Connection 選單中選取 Search 後, 會出現 MiniOS7 Scan

對話視窗顯示網路上已啟動的 MiniOS7 模組

確認狀態欄上顯示模組搜尋

完畢(Search Done).

WISE-580x 快速安裝指南

5

步驟三: 選取模組名稱後移到工具列選取 “IP setting”

於清單上選取模組名稱後移到工具列選取 IP setting

步驟四: 設定新 IP 後選取 “Set” 鈕

步驟五: 選取 “Yes” 鈕後，請重新開

機 WISE-580x

完成設定後, 於 Confirm 對話視窗選

取 Yes 鈕結束程序。隨後請重新開機

WISE-580x。

WISE-580x 快速安裝指南

6

5

--------------------------------------------------------------

前往

WISE

規則設定網頁

使用者透過 WISE 控制器所提供的規則設定網頁，只需使用滑鼠點選設定，即可完

成控制器上工作邏輯的規劃。

步驟一: 開啟瀏覽器，填入 WISE 控制器 IP 作為瀏覽器的 URL 位址

開啟電腦上的瀏覽器(推薦使用 IE，新版瀏覽器尤佳)，輸入 WISE 控制器的 IP 作

為 URL 位址(如有重新設定 IP，請確認所輸入 IP 是否正確)。

步驟二: 進入 WISE 規則設定頁面

進入 WISE-580x 控制器所提

供的規則設定頁面，使用預設

密碼”wise”登入後，僅需依照

首頁上的設定流程(基本設定

進階設定規則設定規則下

載)，即可完成 WISE 控制器的

邏輯規則編排。

步驟三: 設定流程中的細節，請參照 WISE 操作手冊

ICP WISE-5800-MTCP クイックスタートガイド

このマニュアルも適しています

ICP WISE-5800-MTCP クイックスタートガイド

他の言語で

関連論文

その他のドキュメント