Hitachi D 6SB Handling Instructions Manual
- カテゴリー
- パワードリル
- タイプ
- Handling Instructions Manual
このマニュアルも適しています
Drill
D6SH
•
D 6SB
Handling instructions
Read through carefully and understand these instructions before use.
D6SH
2008.07.31, 11:121
1
1
2
3
2
3
4
7
8
5
6
➡
➡
1
1
2
3
4
5
6
7
8
Stopper rod
Stopper holder
Stopper bolt
Hook
Drill chuck
Chuck wrench
Tighten (clockwise)
Loosen (counterclockwise)
2008.07.31, 11:121
2
2008.07.31, 11:122
3
䡬
2008.07.31, 11:123
4
2008.07.31, 11:124
5
GENERAL SAFETY RULES
WARNING!
Read all instructions
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
The term “power tool” in all of the warnings listed below
refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area
a) Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which may ignite the
dust of fumes.
c) Keep children and bystanders away while operating
a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in
the off position before plugging in.
Carrying power tools with your finger on the
switch or plugging in power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce dust related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different from
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of
reach of children and infirm persons.
2008.07.31, 11:135
6
SPECIFICATIONS
Model D6SH D6SB
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input 230 W, 240 W*
No-load speed 4500 / min 3000 / min
Capacity: steel 6.5 mm 6.5 mm
wood 9 mm 13 mm
Weight (without cord) 0.9 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Chuck Wrench ............................................................ 1
(2) Stopper Ass’y ............................................................ 1
(3) Hook ............................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATION
䡬 Drilling holes into various metals, lumbers and
plastics.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting the drill bit
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn. (Fig. 3)
5. Selecting the appropriate drill bit
(1) When drilling holes in metals or plastics:
Use ordinary metalworking drill bits;
Applicable drill sizes range from 0.5 mm min. to
6.5 mm max.
(2) When drilling holes in lumber:
Use woodworking drill bits.
For small holes of 6.5 mm dia, or less, use
metalworking drill bits.
PRACTICAL HANDLING PROCEDURES
1. Pressure:
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result
in a damaged drill bit, decreased drilling efficiency
and/or shortened service life of the drill.
2. When drilling completely through the material:
When the drill bit bores completely through the
material, careless handling often results in a broken
drill bit or damage to the drill body itself due to
the sudden movement of the drill.
Always be alert and ready to release the pushing
force when drilling through the material.
3. Switch operation:
By pulling the trigger switch and depressing the
stopper, the switch is held in the ON position for
continuous operation. To turn the drill OFF, pull the
trigger switch again and release.
4. Precautions on Boring
The drill may become overheated during operation;
however, it is sufficiently operable. Do not cool the
drill bit in water or oil.
Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
PRECAUTIONS ON USING DRILL
1. When mounting the drill bit, insert it fully into the
drill chuck and completely tighten the drill chuck
with the chuck wrench.
If mounting is not done porperly, it is very dangerous
as the drill bit may slip or loosen during operation.
2. Do not wear gloves made of stuff liable to roll up
such as cotton, wool, cloth or string, etc.
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
4. When placing the drill on the floor, make sure that
the drill has stopped completely.
5. Before drilling into a wall, floor or ceiling, thoroughly
confirm that no items such as electric cables or
conduits are buried inside.
6. When working in high position, take care of
downword direction.
2008.07.31, 11:136
7
5. Using stopper assembly (Fig.1)
NOTE: The stopper rod can be fixed on whichever
side of the housing.
Adjust the stopper rod to reach a required drilling
depth. To fix it securely, use the stopper bolt.
6. Caution immediately after use
Immediately after use, if the Drill is still revolving
and it is placed on a location where considerable
ground chips and dust have accumulated, dust may
occasionally be absorbed into the Drill mechanism.
Always pay attention to this possibility.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch power OFF and disconnect the plug
from the receptacle during maintenance and inspection.
1. Inspecting the drill bit
Since use of an abraded drill bit will cause motor
malfunctioning and degraded efficiency, replace the
drill bit with a new one or resharpening without
delay when abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loosened, retighten them immediately,
Failure to do so could result in serious hazard.
3. Servicing
Consult an authorized Service Center in the event
of power tool failure.
4. Service parts list
A : Item No.
B : Code No.
C : No. Used
D : Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Authorized Service
Center.
This Parts List will be helpful if presented with the
power tool to the Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE:
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject of
change without prior notice.
2008.07.31, 11:137
8
D6SH
ABC D
1 980057 1 10TL2
2 314679 1 6.5TLRA “1”
3 314668 1
4 6001VV 1 6001VVCMPS2L
5 314669 1
6 314670 1
7 987105 1 S-10
8 626VVM 1 626VVC2PS2L
9 360439E 1 220V-230V
10 340390E 1 220V-230V
11 626VVM 1 626VVC2PS2L
12 314671 1
13 314673 1
14 ———— 1
15 301653 6 D4×20
16 314677 1
17 314676 1
18 314675 1
19 ———— 1
20 963069 2 M5
21 314678 1
22 930483 2
23 999041 2
24 980063 2
25 953327 1 D8.8
26 937631 1
27 984750 2 D4×16
28 ———— 1
29 994734 1
30 960356 2 M3.5
31 930039 1
32 314674 1
2008.07.31, 11:138
9
D6SB
ABC D
1 980057 1 10TL2
2 314679 1 6.5TLRA “1”
3 314668 1
4 6001VV 1 6001VVCMPS2L
5 ———— 1
6 314670 1
7 987105 1 S-10
8 626VVM 1 626VVC2PS2L
9 360441E 1 220V-230V
10 340390E 1 220V-230V
11 626VVM 1 626VVC2PS2L
12 314671 1
13 314673 1
14 ———— 1
15 301653 6 D4×20
16 314677 1
17 314676 1
18 314675 1
19 ———— 1
20 963069 2 M5
21 314678 1
22 930483 2
23 999041 2
24 980063 2
25 953327 1 D8.8
26 937631 1
27 984750 2 D4×16
28 ———— 1
29 994734 1
30 960356 2 M3.5
31 930039 1
32 314674 1
2008.07.31, 11:139
10
2008.07.31, 11:1310
808
Code No. C99080722
Printed in China
2008.07.31, 11:1311
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Hitachi D 6SB Handling Instructions Manual
- カテゴリー
- パワードリル
- タイプ
- Handling Instructions Manual
- このマニュアルも適しています
他の言語で
- English: Hitachi D 6SB