User Manual For Hunting Camera
1. Product Description
32PCS IR LEDs Latch
LED
indicator
Lens
Microphone
PIR sensor
1 2
LCD Display Screen
Card Slot
USB port
Mode Switch
8AA Batteries Depot
Power Interface Stand Knob Port
3
2. Install the battery
As shown in the figure below, open the upper and lower spring
locks on the side of the device outwards, and the battery
compartment will appear on the right side of the device. Put 8
AA alkaline batteries into the battery compartment in the
direction of the positive and negative electrode identifiers of
the battery. After debugging the working mode, close the battery
compartment according to the above steps in reverse order.
Note: Please use the same brand of batteries with the same
power each time. Do not mix batteries of different brands.
When the power is low, please replace with new batteries in time.
4
3. Insert the SD card
1．Open the battery compartment
of the device.
2．Confirm that the device is off.
(The switch is in the OFF position)
3．Insert the TF card in the
direction indicated.
Note: Please use a better quality
TF card on the market (Class6 and
above speed is recommended).
Do not use excessive force when
inserting the TF card, and pay
attention to the correct direction
of the card.
4. User guides
1. Enter test mode: Open the battery compartment of the
device, as shown in the figure below.
5
2．Put the switch in the TEST position to start the device and
enter the test mode. The screen will be displayed when the
device is turned on..
3．Device control pane
6
Menu: enter/exit the menu, return to the last operation/mode.
Replay: enter/exit playback mode.
Up: move the cursor up to select/switch to the recording mode.
Down: move the cursor down to select/switch to the photo mode.
Right: move the cursor to the right to select.
Left: move the cursor to the left to select.
Shooting:take photo or video.
Confirm: Confirm operation.
4. Test mode settings
• Mode: Can be set to take photo/video/photo+video.
• Shooting interval: The shooting interval can be set between 5
seconds and 60 minutes.
• PIR sensitivity: can be set to three levels of high, medium and
low.
• Number of photos: Can be set to 1/2/3.
• Video length: It can be set between 3 seconds and 10 minutes.
• Video resolution: 1920x1080P/1280x720P/640x480P.
• Language: Support multi-language version.
• System time setting: Set the system clock of the device.
• Watermark: can be set to time & date / date / off.
• Photo pixels: Can be set to 5M/8M/12M/16M/20M.
• System: Display the firmware version number.
• Video sound: can be set to turn on/off.
• Timer shooting settings: can be set to on/off.
• Timer: timer shooting time can be set (start and end time).
• Password setting: can be set to close or open (4-digit password).
• Format: Format the SD card (data will be cleared).
• Restore factory settings: The device parameters can be
restored to the default state.
7
5. Enter Hunting ON mode
After setting the required working mode,
pull the switch to ON mode to enter the
formal working mode. After the countdown
is 5 seconds, the LCD turns off, and the
device can be placed in a suitable position
and it can be used normally.
6. How to use the strap
Pass the tail of the strap through the strap opening of the back
shell, then tie the straps to a suitable tree height, and pass the
tail of the strap through the hardware buckle, just pull it tight.
USB Strap
8
7.Notes
•The menu parameters can be adjusted only in the test mode.
•If you have not taken pictures, try to put your camera in a place
where there is no heat source.
•Check the PIR sensitivity, for warm environmental conditions,
set the sensor level to "low", for cold weather, set the sensor to
"high".
•When the user forgets the password, press the MENU+REPLAY
button at the same time and then turn it on to clear the original
password.
打 猎 机 说 明 书
1. 产品说明
红外灯
LED
指示灯
麦克风
1 2
3
2. 电池安装
如下图，将设备侧面上下两个弹簧锁扣向外打开，电池仓将会出
现在设备主体右侧。将8节AA碱性按电池正负极标识符方向装入
电池仓，调试好工作模式后再按以上逆顺序步骤合上电池仓。
注意： 每次请使用同一品牌相同电量的电池，不要混用不同品牌
的电池，当电量较低时请及时更换新电池
4
3. 装载SD内存卡
1. 打开设备电池仓。
2. 确认设备在关机状态。
（开关置于OFF位置）
3. 按标示方向插入TF卡。
注意：
请使用市面上质量较好的TF卡
（建议Class6及以上速度）。
装载TF卡时不要用力过猛，
并注意正确的插卡方向。
4. 开始使用
1. 进入测试模式：打开设备电池仓，如下图。
5
2. 将开关置于TEST位置就可以启动设备进入测试模式了。设备
开机时会显示开机画面。
3. 设备控制面板
6
MENU 菜单键：进入/退出菜单，返回上一次操作/模式。
REPLAY 回放键：进入/退出回放模式。
方向上键：向上移动光标选择/快捷切换到录像模式。
方向下键：向下移动光标选择/快捷切换到拍照模式。
方向右键：向右移动光标选择。
方向左键：向左移动光标选择。
拍摄键：执行拍照或录像。
确认键：确认操作。
4. 测试模式设置
● 模式：可设为拍照/录像/拍照+录像。
● 拍摄间隔：可设拍摄间隔时间5秒到60分钟之间。
● PIR灵敏度：可设为高中低三个级别。
● 拍照张数：可设为1/2/3 张。
● 录像长度：可在3秒到10分钟之间设定。
● 录像分辨率：1920x1080P/1280x720P/640x480P
● 语言：支持多国语言界面。
● 系统时间设置：设置设备的系统时钟。
● 水印：可设为时间&日期/日期/关闭三种。
● 照片像素：可设为5M/8M/12M/16M/20M。
● 系统：显示固件版本号。
● 录像声音：可设开启/关闭。
● 定时拍摄设置：可设为开启/关闭。
● 定时器：可设置定时拍摄时间（开始与结束时间）。
● 密码设置：可设关闭或开启（4位数字的密码）。
● 格式化：格式化SD卡（数据将被清除）。
● 恢复出厂设置：可将设备参数恢复到默认状态。
7
5. 进入打猎模式
设置好需要的工作模式后，将开关拔到
ON模式就可以进入正式工作模式了。
倒计时5秒后LCD关闭进入打猎模式，
设备放置在合适的位置就可以正常使用了。
6. 绑带的使用方法
将绑带尾部穿过后壳的绑带口，然后把绑带绑到合适的树木高度，
再把绑带尾部穿过五金扣位，拉紧即可。
USB
8
7. 注意事项
● 只有在测试模式才可以调整菜单参数。
● 如果一直没有拍到照片，试着把你的相机放在一个没有热源的地方。
● 检查PIR灵敏度，对于温暖的环境条件，将传感器灵敏度设置为
“低”，对于寒冷天气使用，将传感器灵敏度设置为“高”。
● 当用户忘记密码时，可以同时按MENU+REPLAY键后再开机就
可以清除原设置的密码。
卡扣
镜头
感应器
绑带
显示屏 电池卡槽
模式开关
USB接口
T F卡槽
电源接口 三脚架螺母
675*95m m 105克铜版纸正反面黑白印刷 风琴折
/
