Black & Decker BEH200 は、木材、金属、プラスチック、石材への穴あけやねじ締め作業に最適なインパクトドリルです。軽量でコンパクトな設計で、狭い場所でも作業しやすいのが特長です。また、2段階のスピード設定により、さまざまな素材に対応できます。さらに、人間工学に基づいたハンドルとサイドハンドルにより、長時間使用しても疲れにくくなっています。
使用例： ・棚や家具の組み立て ・配線の穴あけ ・水道の修理 ・車のメンテナンス ・DIYプロジェクト
Black & Decker BEH200 は、木材、金属、プラスチック、石材への穴あけやねじ締め作業に最適なインパクトドリルです。軽量でコンパクトな設計で、狭い場所でも作業しやすいのが特長です。また、2段階のスピード設定により、さまざまな素材に対応できます。さらに、人間工学に基づいたハンドルとサイドハンドルにより、長時間使用しても疲れにくくなっています。
使用例： ・棚や家具の組み立て ・配線の穴あけ ・水道の修理 ・車のメンテナンス ・DIYプロジェクト
475
3
6
1
2
3
8
BEH200
简体中文
2
7
6b
7a
6
6a
6c
A
B
5
C
3
D E
2
3
3
ENGLISH
(Original instructions)
3
Intended use
Your BLACK+DECKER BEH200 Impact drill has been
designed for drilling in wood, metal, plastics, and masonry
as well as for screwdriving purposes. This tool is intended for
consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings,
instructions, illustrations and
tool. Failure to follow the warnings and
instructions listed below may result in electric
.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
4
F
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool.
Do not use a power tool while you are tired or under
A
moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
4
ENGLISH
(Original instructions)
Use of dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Service
a.
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for rotary
and chiselling hammers
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Brace the tool properly before use. This tool produces
a high output torque and without properly bracing the tool
during operation, loss of control may occur resulting
in personal injury.
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal
injury.
Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Use a face or dust mask whenever the operations may
Safety of others
This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
5
ENGLISH
(Original instructions)
Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or ac-
cessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear ear protectors with Impact drills. Exposure
to noise can cause hearing loss
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. Variable speed switch
2. Lock on button
3. Forward/reverse switch
4. Drilling mode selector
5. Chuck
6. Side handle
7. Depth gauge (Not Supplied)
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Turn the knob (6c) counter clockwise until you can slide
the side handle (6) onto the front of the tool as shown.
Rotate the side handle into the desired position ensuring
that the notches (6a) engage with the sprocket (6b).
Insert the depth guage (7) (Not Supplied) into the mount-
ing hole (7a).
Set the drilling depth as described below.
Tighten the side handle by turning the knob (6c)
clockwise.
Note:
depending on personal preference.
Fitting a drill bit
Open the chuck by turning the front part with one
hand while holding the rear part with the other.
the chuck.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning!
the location of wiring and pipes.
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counter clockwise) rotation.
To select forward rotation, push the forward/reverse
switch (3) to the left position.
To select reverse rotation, push the forward/reverse
button to the right.
Warning! Never change the direction of rotation while the
motor is running.
Slacken the side handle (6) by turning the knob (6a)
counter clockwise.
Set the depth guage (7) (Not Supplied) to the desired
position. The maximum drilling depth is equal to the
distance between the tip of the drill bit and the front end of
the depth guage.
Tighten the side handle by turning the knob (6c)
clockwise.
For Impact drilling in masonry and concrete, set the
drilling mode selector (4) to the
position.
For drilling in steel, wood and plastics or for screw driving
set the operating mode selector (4) to the position.
6
ENGLISH
(Original instructions)
Switching on and off
To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far you
press the switch. As a general rule, use low speeds
for large diameter drill bits and high speeds for smaller
diameter drill bits.
For continuous operation, press the lock-on button (2)
and release the variable speed switch. The lock on button
is available only at full speed in forward mode. In the
reverse mode, the lock on button is not available.
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
Protecting the environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials.
Please recycle electrical products and batteries
according to local provisions.
Further information is available at www.2helpU.com
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
address indicated in this manual. Alternatively, a list of author-
ised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Reuse of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Some local governments may require the local or municipal
waste disposal centers or retailers of new products to provide
households with electronic product recycling services.
Technical data
BEH200
Input voltage V
AC
220
Power input W 500
No load speed min
-1
0 ~ 2900
Max. drilling capacity
Concrete mm
13
Steel mm
13
Wood mm
20
Weight kg
1.69 with side handle
7
ENGLISH
(Original instructions)
NOTE
BLACK+DECKER's policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers
for range availability.
Service Information
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the BLACK+DECKER location
nearest to you.
8
4
F
c.
d.
e.
f.
BLACK+DECKER BEH200
1.
a.
b.
c.
2.
a.
b.
RCD RCD
3.
a.
b.
c.
d.
e.
f.
g.
h.
4.
a.
b.
c.
d.
e.
f.
g.
h.
5.
a.
3
9
RCD RCD
10
D
BLACK+ECKER
3
A B
6c 6
6a
6b
7 7a
6c
E
6a 6
7
6c
F
4
4
C
1.
2.
3.
4.
5.
6.
7.
B
1
2
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER BLACK+DECKER
www.2helpU.com
www.2helpU.com
3
11
BLACK+DECKER
12
BEH200
交
220
500
0 ~ 2900
13
13
20
1.69
200
N855951
04
/2020
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Black & Decker BEH200 は、木材、金属、プラスチック、石材への穴あけやねじ締め作業に最適なインパクトドリルです。軽量でコンパクトな設計で、狭い場所でも作業しやすいのが特長です。また、2段階のスピード設定により、さまざまな素材に対応できます。さらに、人間工学に基づいたハンドルとサイドハンドルにより、長時間使用しても疲れにくくなっています。
使用例： ・棚や家具の組み立て ・配線の穴あけ ・水道の修理 ・車のメンテナンス ・DIYプロジェクト
他の言語で
- English: Black & Decker BEH200 User manual
関連論文
-
BLACK+DECKER LSW20 ユーザーマニュアル
-
-
-
-
-
-
BLACK+DECKER KR71RE(K) ユーザーマニュアル
-
BLACK+DECKER BDCDD12 ユーザーマニュアル
-
-
BLACK+DECKER BPDR5510 ユーザーマニュアル