Philips 216V6LSB2/93 ユーザーマニュアル

カテゴリー
テレビ
タイプ
ユーザーマニュアル
www.philips.com/welcome
SC
用户手册 1
客户服务与保修 19
故障排除和常见问题解答 25
216V6
1. 重要 ..........................................................1
1.1 安全措施与维修 ...........................................1
1.2 标志说明 ..........................................................2
1.3 产品和包装材料的废弃 ..........................3
2. 设置显示器 ............................................ 4
2.1 安装 .......................................................................4
2.2 操作显示器 ......................................................5
2.3 卸下底座支撑臂 ...........................................7
3. 图像优化.................................................8
3.1 SmartContrast .................................................8
4. 技术规格.................................................9
4.1 分辨率和预设模式 .................................. 11
5. 电源管理...............................................12
6. 有关规定...............................................13
7. 客户服务与保修 .................................19
7.1 飞利浦平面显示器像素残缺规定 19
7.2 客户服务与保修 ........................................21
8. 故障排除和常见问题解答 ...............25
8.1 故障检修.........................................................25
8.2 一般常见问题解答 .................................. 26
目录
1
1. 重要
1. 重要
此电子版用户指南适合使用 Philips 显示器
的所有用户。 请在使用您的显示器之前花
点时间阅读本用户手册。 它包含与使用显
示器相关的重要信息和注意事项。
产品享受飞利浦保修须符合下列条件:产
品适当用于其设计目的、符合操作说明、
返修时提供原始帐单或付款收据,帐单或
收据应载明购货日期、销售商名称、产品
型号及生产号。
1.1 安全措施与维修
警告
使用本文档中未介绍的控制、调整或过程
可能导致碰撞、电气危险和/或机械危险。
连接和使用电脑显示器时,请阅读并遵循
以下说明。
操作:
• 请使显示器远离阳光直接照射、明亮强
光线、以及任何其他热源。长期暴露于
此类环境可能导致显示器褪色和损坏。
• 移开任何可能掉入通风孔的物品或者会
妨碍显示器电子器件正常冷却的物品。
• 不要堵塞机壳上的通风孔。
• 放置显示器时,确保电源插头和插座便
于插拔。
• 如果通过拔掉电源线或直流电源线关闭
显示器电源,则在重新连接电源线或直
流电源线以进行正常操作之前,必须等
6 秒钟。
• 请务必使用由 Philips 提供的经过认可的
电源线。如果电源线缺失,请与您当地
的服务中心联系。(请参见“消费者信
息中心”)
• 在使用过程中,请勿让显示器受到剧烈
震动或碰撞。
• 在使用或运输期间,不要敲打显示器或
使显示器掉落。
维护
• 为保护显示器以避免可能的损坏,请勿
过分施力于LCD面板。移动显示器时,
抓住边框将其抬起;抬起时,不要将手
或手指放在LCD面板上。
• 长时间不使用显示器时,应拔掉显示器
电源插头。
• 使用略微蘸湿的布清洁显示器时,应拔
掉显示器电源线插头。电源关闭时,可
以使用干布擦拭屏幕。但是,切勿使用
有机溶剂(如酒精)或含氨水的液体清
洁显示器。
• 为避免电击或本机永久性损坏,不要在
多尘、下雨、水附近或过分潮湿的环境
中使用显示器。
• 如果显示器被弄湿了,应尽快用软布擦
拭干净。
• 如果异物或水进入显示器,请立即关闭
电源,并拔掉电源线。然后,取出异物
或擦干水,并送到维修中心进行检修。
• 请勿在炎热、阳光直接照射或严寒的地
方存放或使用显示器。
• 为了保持显示器的最佳性能并延长使用
寿命,请在符合下列温度和湿度条件的
地方使用显示器。
• 温度:0-40˚C 32-104˚F
• 湿度:20-80% RH
关于图像烙印/重影的重要信息。
• 显示器无人看管时务必启动移动的屏幕
保护程序。如果显示器将显示静止不变
的内容,请务必启用屏幕定期刷新应
用程序。长时间不间断显示静止或静态
图像可能会在屏幕上造成“烙印”,也
称“残像”或“余像”。
“烙印”、“残像”或“余像”是LCD
面板技术的一种常见现象。多数情况
下,关掉电源一定时间后,“烙印”
、“残像”或“余像”会逐渐消失。
小心
若不激活屏幕保护程序或者屏幕定期刷新
应用程序,可能导致严重的“烙印”、
“残像”或“余像”不会消失,不能修
2
1. 重要
复。上面提到的损坏不在保修范围内。
维修
• 只有专业的维修人士可以打开机壳盖。
• 如果在维修或集成时需要任何文档,请
与您当地的服务中心联系。(请参见
“消费者信息中心”一章)
• 关于运输信息,请参见“技术规格”。
• 不要将显示器放在阳光直接照射的车
内。
如果显示器工作不正常,或者当您参照本
手册中的操作说明而不知道应执行哪个步
骤时,请与服务技术人员联系。
1.2 标志说明
以下分节描述使用于此文件的标志惯例。
注、注意、小心
在此指南中,文字段落配有图标并以黑体
或斜体书写。这些段落含有注、注意或小
心字句。其使用如下:
此图标显示重要信息和提示,以助你更好
地使用你 的电脑系统。
注意
此图标显示的信息提醒你如何避免硬体的
潜在损害或 数据丢失。
小心
此图标显示对身体伤害的可能性,并警告
你如何避免 此问题。
某些小心警告可能以不同格式出现,也可
能不带任何图标。在此类情况下,小心警
告的具体显示由管理机关规定。
3
1. 重要
1.3 产品和包装材料的废弃
废旧电气和电子设备 - WEEE
This marking on the product or on its
packaging illustrates that, under European
Directive 2012/19/EU governing used electrical
and electronic appliances, this product may
not be disposed of with normal household
waste. You are responsible for disposal of
this equipment through a designated waste
electrical and electronic equipment collection.
To determine the locations for dropping off
such waste electrical and electronic, contact
your local government office, the waste disposal
organization that serves your household or the
store at which you purchased the product.
Your new monitor contains materials that can
be recycled and reused. Specialized companies
can recycle your product to increase the
amount of reusable materials and to minimize
the amount to be disposed of.
All redundant packing material has been
omitted. We have done our utmost to make the
packaging easily separable into mono materials.
Please find out about the local regulations on
how to dispose of your old monitor and packing
from your sales representative.
Taking back/Recycling Information for
Customers
Philips establishes technically and economically
viable objectives to optimize the environmental
performance of the organization's product,
service and activities.
From the planning, design and production
stages, Philips emphasizes the important of
making products that can easily be recycled. At
Philips, end-of-life management primarily entails
participation innational take-back initiatives
and recycling programs whenever possible,
preferably in cooperation with competitors,
which recycle all materials (products and
related packaging material) in accordance with
all Environmental Laws and taking back program
with the contractor company.
Your display is manufactured with high quality
materials and components which can be
recycled and reused.
To learn more about our recycling program
please visit
http://www.philips.com/sites/philipsglobal/
about/sustainability/ourenvironment/
ourrecyclingprogram.page
4
2. 设置显示器
2. 设置显示器
2.1 安装
包装箱内物品
216V6
Philips and the Philips’ Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license from Koninklijke
Philips N.V.
Monitor drivers
User’s Manual
使用 前请阅读使用说明
保留备用
2
©
0
1
5
K
o
n
i
n
k
l
i
j
k
e
h
i
l
i
P
p
s
l
e
c
E
t
r
o
n
i
c
s
,
N
V
.
.
A
l
l
r
i
g
h
t
s
r
e
s
e
r
v
e
d
.
U
n
a
u
t
h
o
r
i
z
e
d
d
u
p
l
i
c
i
o
a
t
n
i
s
a
v
i
o
l
a
t
i
o
n
o
f
a
p
l
i
c
p
a
b
l
e
l
a
w
s
.
M
a
d
e
a
n
d
r
n
t
p
i
e
d
i
n
C
h
i
n
a
.
V
e
r
s
i
o
n
* 视国家(地区)而定
只应使用交流/直流适配器型号:
Philips ADPC1936/ADS-25FSG-19.
安装底座支撑臂
1. 将显示器正面朝下放在平滑柔软的表面
上,注意不要刮擦或损坏屏幕。
2. 连接/滑动显示器的底座支柱,直至将其
卡入到位。
3. 用双手拿住显示器底座支撑臂,用力将
底座支撑臂插入底座支撑柱。
*VGA
* 交流 / 直流适配器 * 交流 / 直流适配器
*HDMI
5
2. 设置显示器
连接到 PC
216V6LSB2
1
1
3
2
2
交流/直流电源输入
VGA 输入
Kensington 防盗锁
216V6LHSB2
1
3
3
2
4
4
5
2
1
交流/直流电源输入
HDMI音频输出
VGA 输入
HDMI输入
Kensington 防盗锁
连接到 PC
1. 将连接线牢固连接到显示器背面插口。
2. 先关闭电脑,再拉出电源线。
3. 将显示器讯号线连在电脑背面的视听连
接器。
4. 将电脑及显示器的电源线插入最接近的
插座内。
5. 打开计算机和显示器的电源。如果显示
器显示图像,则安装完毕。
2.2 操作显示器
产品正面说明
5
6 2347
打开和关闭显示器的电源。
访问 OSD 菜单。
确认 OSD 调整。
返回上一级 OSD
调整亮度。
调整 OSD 菜单。
更改显示格式。
自动调整显示器。
6
2. 设置显示器
屏幕显示 (OSD) 说明
什么是屏幕显示 (OSD)?
屏幕显示(On-Screen DisplayOSD)是所
Philips LCD都具有的特性。它使得最终用
户可以通过屏幕说明窗口直接调整屏幕性
能或选择显示器功能。用户友好的屏幕显
示界面如下所示:
216V6LSB2



 
 



 





216V6LHSB2







控制键简介
在上面所示的 OSD 中,您可以按显示器前
面板上的 按钮移动光标,然后按 OK
钮确认所作的选择或更改。
OSD 菜单
下面是 OSD 结构概览。 以后进行各种调整
时,可以以此作为参考。
Main menu Sub menu
Picture
Input
Picture Format
Brightness
Contrast
Sharpness
SmartContrast
Gamma
VGA (available for selective models)
HDMI (available for selective models)
Over Scan
Wide Screen, 4:3
0~100
0~100
OSD Settings
Setup
Language
Color
Horizontal
Vertical
Transparency
OSD Time Out
H.Position
Auto
V.Position
Phase
Clock
Resolution Notification
Reset
Information
English, Deutsch, Español, Ελληνική, Français,
Italiano, MaryarNederlands, Português,
Português do BrazilPolskiРусский ,Svenska
SuomiTürkçeČeštinaУкраїнська, 简体中文,
中文,日本語,한국어
Color Temperature
sRGB
User Define
0~100
0~100
Off, 1, 2, 3, 4
5s, 10s, 20s, 30s, 60s
0~100
On, Off
Yes, No
0~100
0~100
0~100
6500K, 9300K
Red: 0~100
Green: 0~100
Blue: 0~100
0~100
On, Off
1.8, 2.0, 2.2, 2.4, 2.6
On, Off
Audio
Mute
(available for selective models)
Volume
(available for selective models)
0~100
On, Off
(available for selective models)
(available for selective models)
7
2. 设置显示器
分辨率通知
根据设计,此显示器在其固有分辨率 1920
x 1080 @ 60 Hz 时性能最佳。当显示器以不
同的分辨率开机时,屏幕上会显示提醒。
请使用 1920 x 1080 @ 60 Hz 以达到最佳效
果。
如果要关闭原始分辨率提示讯息,请在屏
幕显示选单的设定中进行设定。。
物理功能
倾斜
2.3 卸下底座支撑臂
卸下底座支撑臂
在开始拆卸显示器底座前,请遵循下面的
说明以避免可能的损坏或伤害。
1. 将显示器正面朝下放在平滑的表面上,
注意不要刮擦或损坏屏幕。
2. 按锁定夹,从底座支撑柱上卸下底座支
撑臂。
1
3. 卸下底座支撑柱。
2
8
3. 图像优化
3. 图像优化
3.1 SmartContrast
这是什么?
一项独特的技术,可以动态分析所显示的
内容并自动优化LCD显示器的对比度以达到
最佳清晰度和观看舒适度,对于清晰、锐
利和明亮的图像提高背光亮度,对于深色
背景的图像降低背光亮度。
为什么需要它?
您希望在显示各种内容时都能达到最佳的
清晰度和观看舒适度。SmartContrast
态控制对比度并调整背光,以提供清晰、
锐利、明亮的游戏和视频图像或者清晰可
读的办公文字。通过降低显示器的功耗,
可以节省能耗成本,延长显示器的使用寿
命。
它如何工作?
启用 SmartContrast 时,它将实时分析显示
的内容以调整颜色和控制背光亮度。当观
看视频或玩游戏时,此功能可动态增强对
比度,以达到美好的娱乐体验。
9
4. 技术规格
4. 技术规格
图片/显示
LCD面板类型 TFT-LCD
背光
W-LED system
面板尺寸 20.7" W (52.6 cm
)
宽高比 16:9
像素点距 0.2385 x 0.2385 mm
SmartContrast 10,000,0001
响应时间(典型)
5ms
最佳分辨率 1920 x 1080 @ 60Hz
视角
90° (H) / 65° (V) @ C/R > 10
显示颜色数 1670
垂直刷新率 56Hz -76Hz
水平频率 30kHz - 83kHz
sRGB
连接性
信号输入
216V6LSB2
VGA(
模拟
)
216V6LHSB2
VGA(
模拟
),HDMI
( 数字)
输入信号 分离同步,绿色同步
音频输入/输出
216V6LHSB2
HDMI audio out
方便性
用户便利性
OSD语言
英语、德语、西班牙语、法语、意大利语、匈牙利语、荷
兰语、葡萄牙语、巴西葡萄牙语、俄语、波兰语、瑞典
语、芬兰语、土耳其语、捷克语、乌克兰语、简体中文、
日语、韩语、希腊语、繁体中文
其他便利性 Kensington
即插即用兼容性 DDC/CI, sRGB,
Win 7/ Win8/ Win 8.1/ Win 10
, Mac OSX
底座
倾斜 -5 / +20
216V6LSB2:
电源
工作模式 27.03W(典型),29.65W(最大)
睡眠(待机) 0.5W
不亮 0.5W
电源 LED 指示灯 工作模式:白色,待机/睡眠:白色(闪烁)
电源 外置,100-240VAC, 50-60Hz
10
4. 技术规格
216V6LHSB2:
电源
工作模式 24.87W(典型),28.59W(最大)
睡眠(待机) 0.5W
不亮 0.3W
电源 LED 指示灯 工作模式:白色,待机/睡眠:白色(闪烁)
电源 外置,100-240VAC, 50-60Hz
外形尺寸
产品(含底座)(WxHxD
488 x 365 x 200 mm
产品(不含底座)(WxHxD
488 x 295 x 39 mm
重量
产品(含底座)
2.10kg
产品(不含底座)
1.82kg
运行条件
温度范围(工作) 0℃到40
相对湿度(工作) 20%80%
大气压力(工作) 7001060hPa
温度范围(非工作) -20℃到60
相对湿度(非工作) 10%90%
大气压力(非工作) 5001060hPa
环境
ROHS
EPEAT Silverwww.epeat.net
包装 100% 可回收
符合性和标准
管制认证
216V6LSB2CCC,CEL,CE Mark, FCC Class B, CU, SEMKO,
BSMI, ETL, ISO9241-307, CB
216V6LHSB2CCC,CEL,CE Mark, CB
机壳
颜色 黑色
表面处理 纹理
1. EPEAT Gold Sliver 仅在 Philips 注册了产品的地区有效。有关您所在国家地区的注册状况 ,
请访问 www.epeat.net
2. 此数据如有变更,恕不另行通知。访问 www.philips.com/support 下载最新版本的宣传页。
11
4. 技术规格
4.1 分辨率和预设模式
最大分辨率
216V6LSB2
1920 x 1080 @ 60 Hz(模拟输入)
216V6LHSB2
1920 x 1080 @ 60 Hz(模拟输入)
1920 x 1080 @ 60 Hz(数字输入)
推荐分辨率
216V6LSB2
1920 x 1080 @ 60 Hz(模拟输入)
216V6LHSB2
1920 x 1080 @ 60 Hz(数字输入)
水平频率 (kHz) 分辨率 垂直频率 (Hz)
31.47 720 x 400 70.09
31.47 640 x 480 59.94
35.00 640 x 480 66.67
37.86 640 x 480 72.81
37.50 640 x 480 75.00
37.88 800 x 600 60.32
46.88 800 x 600 75.00
48.36 1024 x 768 60.00
60.02 1024 x 768 75.03
44.77 1280 x 720 59.86
63.89 1280 x 1024 60.02
79.98 1280 x 1024 75.03
55.94 1440 x 900 59.89
70.64 1440 x 900 74.98
65.29 1680 x 1050 59.95
67.50 1920 x 1080 60.00
请注意,此显示器在其固有分辨率 1920 x
1080 @ 60Hz 时工作效果最佳。 为达到最
佳显示效果,请遵循此项关于分辨率的建
议。
12
5. 电源管理
5. 电源管理
如果 PC 中安装了 VESA DPM 兼容显示卡或
者软件,显示器可以在不使用时自动降低
功耗。如果检测到来自键盘、鼠标或其它
输入设备的输入,显示器将自动“唤醒”
。下表介绍此自动省电功能的功耗和信号
时序:
216V6LSB2:
电源管理定义
VESA 模式 视频
水平
同步
垂直
同步
使用的功率 LED 颜色
工作 开启
27.03 W(典型)
29.65 W(最大)
白色
睡眠 关闭 0.5W(典型)
白色
(闪烁)
关闭 关闭 - - 0.5W(典型) 关闭
216V6LHSB2:
电源管理定义
VESA 模式 视频
水平
同步
垂直
同步
使用的功率 LED 颜色
工作 开启
24.87 W(典型)
28.59 W(最大)
白色
睡眠 关闭 0.5W(典型)
白色
(闪烁)
关闭 关闭 - - 0.3W(典型) 关闭
下面的设置用于测量此显示器的功耗。
固有分辨率:1920 x 1080
对比度:50%
亮度:100%
色温:6500k 全白图案
此数据如有变更,恕不另行通知。
13
6. 有关规定
6. 有关规定
Lead-free Product
Lead free display promotes
environmentally sound recovery
and disposal of waste from electrical
and electronic equipment. Toxic
substances like Lead has been eliminated and
compliance with European communitys
stringent RoHs directive mandating restrictions
on hazardous substances in electrical and
electronic equipment have been adhered to
in order to make Philips monitors safe to use
throughout its life cycle.
EPEAT
(www.epeat.net)
The EPEAT (Electronic
Product Environmental
Assessment Tool) program
evaluates computer
desktops, laptops, and monitors based on
51 environmental criteria developed through
an extensive stakeholder consensus process
supported by US EPA.
EPEAT system helps purchasers in the public
and private sectors evaluate, compare and
select desktop computers, notebooks and
monitors based on their environmental
attributes. EPEAT also provides a clear and
consistent set of performance criteria for the
design of products, and provides an opportunity
for manufacturers to secure market recognition
for efforts to reduce the environmental impact
of its products.
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste
EPEATS requirement that all registered
products meet ENERGY STARs energy
CE Declaration of Conformity
This product is in conformity with the following
standards
EN60950-1:2006+A11:2009+A1:
2010+A12:2011 (Safety requirement of
Information Technology Equipment).
EN55022:2010 (Radio Disturbance
requirement of Information Technology
Equipment).
EN55024:2010 (Immunity requirement of
Information Technology Equipment).
EN61000-3-2:2006 +A1:2009+A2:2009
(Limits for Harmonic Current Emission).
EN61000-3-3:2008 (Limitation of Voltage
Fluctuation and Flicker) following provisions
of directives applicable.
EN50581:2012 (Technical documentation
for the assessment of electrical and
electronic products with respect to the
restriction of hazardous substances)
EN 50564:2011 (Electrical and electronic
household and office equipment
Measurement of low power consumption)
following provisions of directives applicable
2006/95/EC (Low Voltage Directive).
2004/108/EC (EMC Directive).
2009/125/EC (ErP Directive, EC No.
1275/2008 Implementing Directive
for Standby and Off mode power
consumption) and is produced by a
manufacturing organization on ISO9000
level.
2011/65/EU (RoHS Directive) and is
produced by a manufacturing organization
on ISO9000 level
The product also comply with the following
standards
ISO9241-307:2008 (Ergonomic
requirement, Analysis and compliance test
methods for electronic visual displays).
Note
We recommend you switch off the monitor
when it is not in use for a long time.
14
6. 有关规定
Federal Communications Commission (FCC)
Notice (U.S. Only)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
Use only RF shielded cable that was supplied
with the monitor when connecting this monitor
to a computer device.
To prevent damage which may result in fire or
shock hazard, do not expose this appliance to
rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS
ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked
with FCC Logo,
United States Only
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Commission Federale de la Communication
(FCC Declaration)
Cet équipement a été testé et déclaré
conforme auxlimites des appareils
numériques de class B,aux termes de l'article
15 Des règles de la FCC. Ces limites sont
conçues de façon à fourir une protection
raisonnable contre les interférences nuisibles
dans le cadre d'une installation résidentielle.
CET appareil produit, utilise et peut émettre
des hyperfréquences qui, si l'appareil n'est
pas installé et utilisé selon les consignes
données, peuvent causer des interférences
15
6. 有关规定
nuisibles aux communications radio.
Cependant, rien ne peut garantir l'absence
d'interférences dans le cadre d'une
installation particulière. Si cet appareil est
la cause d'interférences nuisibles pour
la réception des signaux de radio ou de
télévision, ce qui peut être décelé en
fermant l'équipement, puis en le remettant
en fonction, l'utilisateur pourrait essayer de
corriger la situation en prenant les mesures
suivantes:
Réorienter ou déplacer lantenne de
réception.
Augmenter la distance entre
léquipement et le récepteur.
Brancher léquipement sur un autre
circuit que celui utilisé par le récepteur.
Demander laide du marchand ou dun
technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu
l'approbation des services compétents
en matière de conformité est susceptible
d'interdire à l'utilisateur l'usage du présent
équipement.
N'utiliser que des câbles RF armés pour
les connections avec des ordinateurs ou
périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE
B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR
DU CANADA.
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification
Notice
The equipment should draw power from a
socket with an attached protection circuit (a
three-prong socket). All equipment that works
together (computer, monitor, printer, and so
on) should have the same power supply source.
The phasing conductor of the room's electrical
installation should have a reserve short-circuit
protection device in the form of a fuse with a
nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the
power supply cable must be removed from the
power supply socket, which should be located
near the equipment and easily accessible.
A protection mark "B" confirms that the
equipment is in compliance with the protection
usage requirements of standards PN-93/
T-42107 and PN-89/E-06251.
16
6. 有关规定
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht
den in der "Verordnung über den Schutz vor
Schäden durch Röntgenstrahlen" festgelegten
Vorschriften.
Auf der Rückwand des Gerätes befindet sich
ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften
über die Bauart von Störstrahlern nach Anlage
III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt
sind.
Damit Ihr Monitor immer den in der Zulassung
geforderten Werten entspricht, ist darauf zu
achten, daß
1. Reparaturen nur durch Fachpersonal
durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine
bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen,
die Grundfarben Blau und Rot nicht auf
dunklem Untergrund zu verwenden (schlechte
Lesbarkeit und erhöhte Augenbelastung bei zu
geringem Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel
nach DIN 45 635 beträgt 70dB (A) oder
weniger.
ACHTUNG: BEIM AUFSTELLEN
DIESES GERÄTES DARAUF
ACHTEN, DAß NETZSTECKER UND
NETZKABELANSCHLUß LEICHT
ZUGÄNGLICH SIND.
China RoHS
The People's Republic of China released a
regulation called "Management Methods for
Controlling Pollution by Electronic Information
Products" or commonly referred to as China
RoHS.
中国大陆
RoHS
根据中国大陆《电子电气产品有害物质限制使用标识要求(也称中国大陆
RoHS),以下部分列出了本产品中可能包含的有害物质的名称和含量。
部件名称
有害物质
Pb
Hg
Cd
六价铬
Cr(VI)
多溴联苯
PBB
多溴二苯醚
PBDE
外壳
○ ○
液晶显示屏
/
灯管
×
电路板组件
*
×
电源适配器
×
电源线
/
连接线
×
本表格依据
SJ/T 11364
的规定编制
*
电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、集成电路、连接器等。
:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
×
:表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
但是上表中打
“×”
的部件,其含量超出是因为目前业界还没有成熟的可替代的技术。
环保使用期限
此标识指期限 ( 十年 ), 电子信息产品中含有的
有毒有害物质或元素在正常使用的条件下不会发
生外泄或突变 , 电子信息产品用户使用该电子
信息产品不会对环境造成严重污染或对其人身、
财产造成严重损害的期限.
中国能源效率标识
根据中国大陆《能源效率标识管理办法》本显示器符合以下要求:
能源效率
(cd/W) > 0.85
关闭状态能耗
(W) <1
能效等级
2
能效标准
GB 21520-2008
详细有关信息请查阅中国能效标识网:
http://www.energylabel.gov.cn/
《废弃电器电子产品回收处理管理条例》提示性
说明
为了更好地关爱及保护地球,当用户不再需要此产
品或产品寿命终止时,请遵守国家废弃电器电子产
品回收处理相关法律法规,将其交给当地具有国家
认可的回收处理资质的厂商进行回收处理。
BSMI Notice (Taiwan Only)
17
6. 有关规定
EU Energy Label
The European Energy Label informs you on
the energy efficiency class of this product.
The greener the energy efficiency class of this
product is the lower the energy it consumes.
On the label, you can find the energy efficiency
class, the average power consumption of
this product in use and the average energy
consumption for 1 year.
Note
The EU Energy Label will be ONLY applied on
the models bundling with HDMI and TV tuners.
Restriction on Hazardous Substances
statement (India)
This product complies with the India
E-waste Rule 2011 and prohibits use of lead,
mercury, hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers
in concentrations exceeding 0.1 weight % and
0.01 weight % for cadmium, except for the
exemptions set in Schedule 2 of the Rule.
E-Waste Declaration for India
This symbol on the product or on its packaging
indicates that this product must not be
disposed of with your other household waste.
Instead it is your responsibility to dispose of
your waste equipment by handing it over to
a designated collection point for the recycling
of waste electrical and electronic equipment .
The separate collection and recycling of your
waste equipment at the time of disposal will
help to conserve natural resources and ensure
that it is recycled in a manner that protects
human health and the environ-ment. For more
information about where you can drop off your
waste equipment for recycling in India please
visit the below web link.
http://www.india.philips.com/about/sustainability/
recycling/index.page
18
6. 有关规定
Information for U.K. only
WARNING - THIS APPLIANCE MUST BE
EARTHED.
Important:
This apparatus is supplied with an approved
moulded 13A plug. To change a fuse in this
type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362
5A,A.S.T.A. or BSI approved type.
3. Retit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
3-pin plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5A. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5A.
NOTE:
The severed plug must be destroyed
to avoid a possible shock hazard
should it be inserted into a 13A socket
elsewhere.
(A)
(B)
How to connect a plug
The wires in the mains lead are coloured in
accordance with the following code:
BLUE -NEUTRAL(N)
BROWN -LIVE(L)
GREEN&YELLOW -EARTH(E)
1. The GREEN&YELLOW wire must be
connected to the terminal in the plug
which is marked with the letter "E" or by
the Earth symbol or coloured GREEN or
GREEN&YELLOW.
2. The BLUE wire must be connected to the
terminal which is marked with the letter
"N" or coloured BLACK.
3. The BROWN wire must be connected
to the terminal which is marked with the
letter "L" or coloured RED.
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the three wires.
-
1 / 1

Philips 216V6LSB2/93 ユーザーマニュアル

カテゴリー
テレビ
タイプ
ユーザーマニュアル

他の言語で