1
2
HC5612
1
2
9
1
2
4
8
5
3
2
2
10
1
2
ON
2
1
2
11
8
HQ8505
HC5612/17
©2020 Philips Japan, Ltd.
4222.002.9266.1 02/20
?
Guidance in English
1
CERTIFICATE OF PURCHASE
http://www.
philips.co.jp/
HC5612/17
2
3
100 240V
2
1
OFF
3
OFF
/ /
2
3-152mm
16-28
3
4
OFF
1
OFF
2
1
3
ON
3
ON/OFF
ON 1
OFF
2
OFF
6
27
3 28 1
0.5
ON
5
1
2
3
4
1
mm
2
3
4
ON
5
28mm
1
0.5mm
2
ON
3
4
/
1
7
1
2
3
28mm
0.5mm
6
1
2
1
2
2
3 15mm
3
16 28mm
8
1
OFF
3
4
7
2
OFF
6
5
1
2
0.5mm
MyPhilips
http://www.philips.co.jp/myphilips-about
URL
MyPhilips
9 00 18 00
0120 944 859
Web
1 .
60
2 .
5 35
3 .
OFF
4
.
5 .
6 .
7 .
8 .
9 .
10 .
HairClipper
Series 5000
8
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
oers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Cutting unit
2 Zoom wheel
3 On/o button
4 Charging light
5 Socket for small plug
6 Beard and stubble comb (2 mm)
7 Short hair comb (3-15 mm)
8 Long hair comb (16-28 mm)
9 Thinning comb
10 Supply unit
11 Small plug
12 Cleaning brush
Important safety information
Read this important information carefully before you
use the appliance and its accessories and save it for
future reference. The accessories supplied may vary
for dierent products.
Danger
- Keep the supply unit dry (Fig. 2).
Warning
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the
appliance.
- The supply unit contains a transformer. Do not
cut o the supply unit to replace it with another
plug, as this causes a hazardous situation.
- This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
- Always unplug the appliance before you clean it
under the tap.
- Always check the appliance before you use it. Do
not use the appliance if it is damaged, as this may
cause injury. Always replace a damaged part with
one of the original type.
- This appliance contains batteries that are non-
replaceable.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Do not use the appliance in the bath or shower.
- Never use water hotter than 60 °C to rinse the
appliance.
- Only use this appliance for its intended purpose
as shown in the user manual.
- Do not use the supply unit in or near wall sockets
that contain an electric air freshener to prevent
irreparable damage to the supply unit.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
General
- This appliance can be safely cleaned under the
tap (Fig. 3).
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
Charging
Charge the appliance fully before you use it for the
rst time or if you have not used it for a long time.
It takes approximately 8 hours to fully charge the
appliance.
When the appliance is fully charged, it has a cordless
operating time of up to 75 minutes.
Note: After charging the appliance once fully for the
rst time, you can also use the appliance directly
from the wall socket. Simply connect the appliance
to the wall socket.
Charging with the supply unit
1 Make sure that the appliance is switched o
(Fig. 4).
2 Insert the small plug into the appliance and put
the supply unit in the wall socket (Fig. 5).
When the appliance is charging, the battery status
indicator light ashes green (Fig. 6).
3 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Optimizing the lifetime of the rechargeable
battery
When you have charged the appliance for the rst
time, we advise you to use it until the battery is
completely empty. Continue to use the appliance
until the motor almost stops operating during a
session. Then recharge the battery. Follow this
procedure at least twice a year.
Using the appliance
The hair length settings are indicated in millimeters.
The settings correspond to the remaining hair length
after trimming.
Note: Be careful when you trim for the rst time. Do
not move the trimmer too fast. Make smooth and
gentle movements.
Tip: Start trimming at a high length setting and
reduce the length setting gradually until you have
reached the desired hair length.
Trimming with the trimming comb
The appliance comes with one beard and stubble
comb, a thinning comb, one short hair comb and one
long hair comb.
1 Attach a comb to the appliance (Fig. 7).
2 Turn the zoom wheel to select the desired length
setting (Fig. 8).
Note: When you trim for the rst time, start at the
highest length setting to familiarize yourself with
the appliance.
3 Switch on the appliance.
4 Move the appliance slowly and with light
pressure against the direction of hair growth
(Fig. 9).
Make sure that the at part of the comb always
stays in contact with the skin to obtain an even
result (Fig. 10).
5 Switch o and clean the appliance after each use.
Trimming without comb
Use the trimmer without the trimming comb to trim
hair close to the skin (0.5 mm) or to contour the
neckline and sideburns.
Be careful when you trim without a comb because
the cutting unit removes every hair it touches.
1 Pull the comb o the appliance (Fig. 12).
2 Switch on the appliance.
3 Touch the hair lightly with the cutting unit. Make
well-controlled movements (Fig. 13).
4 Switch o and clean the appliance after each use.
Cleaning
Warning: Never use compressed air, scouring
pads, abrasive cleaning agents or aggressive
liquids such as petrol or acetone to clean the
appliance.
1 Make sure that the appliance is switched o and
disconnected from the wall socket.
2 Wipe the housing of the appliance with a dry
cloth.
3 Remove the comb (Fig. 12) and clean it with the
cleaning brush and/or rinse it under the tap
(Fig. 14).
4 Press the release button. The cutting unit comes
o the appliance (Fig. 15).
5 Clean the cutting unit with the cleaning brush
and/or rinse it under the tap (Fig. 16).
6 Clean the inside of the appliance with the brush
and/or rinse it under the tap (Fig. 17).
7 Carefully shake o excess water and let all parts
air dry completely.
8 Insert the lug of the cutting unit into the guiding
slot and push the cutting unit back onto the
appliance (Fig. 18).
Replacement
Only replace a worn or damaged cutting unit with an
original Philips cutting unit, available from authorized
Philips service center.
1 Press the release button. The cutting unit comes
o the appliance (Fig. 15).
2 Insert the lug of the new cutting unit into the
guiding slot and push the cutting unit onto the
appliance (Fig. 18).
Ordering accessories
To buy accessories or spare parts, visit
www.philips.com/parts-and-accessories or go to
your Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the
international warranty leaet for contact details).
Recycling
- Do not throw away the product with the normal
household waste at the end of its life, but hand
it in at an ocial collection point for recycling. By
doing this, you help to preserve the environment.
- This product contains a built-in rechargeable
battery which shall not be disposed of with
normal household waste. Please take your
product to an ocial collection point or a Philips
service center to have a professional remove the
rechargeable battery.
- Follow your country’s rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
Only remove the rechargeable battery when
you discard the product. Before you remove
the battery, make sure that the product is
disconnected from the wall socket and that the
battery is completely empty.
Take any necessary safety precautions when
you handle tools to open the product and when
you dispose of the rechargeable battery.
The battery must be removed from the
appliance before it is scrapped.
1 Disconnect the appliance from the wall socket
and let the appliance operate until the motor
stops.
2 Insert a athead screwdriver between the
zoom wheel and bezel. Tilt the handle of the
screwdriver to remove the bezel and top panel
(Fig. 19).
3 Use a athead screwdriver to remove the two
screws in the front panel (Fig. 20).
4 Insert a athead screwdriver into the slots
between the front and back panel. Tilt the handle
of the screwdriver to separate the front and back
panels (Fig. 21).
5 Continue this step along the edge of the front
panel to separate the front panel from the back
panel (Fig. 22).
6 Use a athead screwdriver to remove the two
screws next to the zoom wheel (Fig. 23).
7 Release the inner body by pulling on the inlet
area and remove the inner body from the back
panel (Fig. 24).
8 Turn the zoom wheel and slide o the back of the
appliance (Fig. 25).
9 Break the eight snap hooks and remove the cover
of the inner body (Fig. 26).
10 Remove the printed circuit board with a athead
screwdriver (Fig. 27).
11 Cut the connectors from the batteries and remove
the batteries (Fig. 28).
Danger: Do not connect the appliance to the
wall socket again after you have opened the
appliance.
Warranty and support
If you need information or support, please visit
www.philips.com/support or read the international
warranty leaet.
Warranty restrictions
Cutting units are not covered by the terms of the
international warranty because they are subject to
wear.
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact the
Consumer Care Center in your country.
Problem Possible
cause
Solution
The
appliance
produces
an uneven
cutting result.
The comb
does not
touch the
skin when
you move
the appliance
through the
hair.
Make sure the
comb is always
fully in contact with
the skin when you
move the appliance
through the hair.
You only
move the
appliance in
one direction.
Because not
all hairs grow
in the same
direction, move
the appliance in
dierent directions
(upwards,
downwards and
across).
The setting
of the comb
has changed
during
trimming.
Check the setting
of the comb. If you
push the appliance
too hard onto
the scalp, you
may accidentally
change the setting
of the comb.
The comb is
not assembled
correctly.
Detach the comb
and reattach it.
The cutting
performance
decreases
when the
cutting unit
and the comb
are dirty.
Clean the cutting
unit and the comb
(see 'Cleaning').
The
appliance
does not
work when I
switch it on.
The
rechargeable
battery is
empty.
Charge the
appliance. Make
sure that the small
plug is inserted
into the appliance
properly and
the supply unit
is connected to
the wall socket
properly.
14
1.
2.
3.
4.
1
2
3
4
5
6
http://www.philips.co.jp/
12
TEL.
OFF
2
6
Philips Consumer Lifestyle Service Department P.O.Box 20100 9200 CA DRACHTEN
The Netherlands Fax:+31 51 259 2785
http://www.philips.co.jp/
13
HC5612/17
HC5612
HQ8505
)
188 50 57mm
191g
AC100-240V 50/60Hz
8
75
Ni-MH
9W
108-8507 2-13-37
1
2
1
2
3-15mm2mm 16-28mm
6
7
12
8
9
1
2
3
4
5
10
11
1
2
1
HC5612/17
ENGLISH
2
4
3
5
7
6
8
10
9
11
13
12
14
16
15
17
19
18
20
22
21
26
27
28
23
25
24
/