Samsung HT-J7750W ユーザーマニュアル

7.1CH Blu-ray™

Home Entertainment System

User manual

HT-J7750W

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

HT-J7750W-ZK-ENG-0311.indd 1HT-J7750W-ZK-ENG-0311.indd 1 2015-03-11  3:38:092015-03-11  3:38:09

2 - English

Safety Information

~

The slots and openings in the cabinet and in the back

or bottom are provided for necessary ventilation. To

ensure reliable operation of this apparatus, and to

protect it from overheating, these slots and openings

must never be blocked or covered.

- Do not place this apparatus in a confined space,

such as a bookcase, or built-in cabinet, unless

proper ventilation is provided.

- Do not place this apparatus near or over a radiator

or heat register, or where it is exposed to direct

sunlight.

- Do not place vessels (vases etc.) containing water

on this apparatus. A water spill can cause a fire or

electric shock.

~

Do not expose this apparatus to rain or place it near

water (near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming

pool, etc.). If this apparatus accidentally gets wet,

unplug it and contact an authorized dealer immediately.

~

This apparatus uses batteries. In your community,

there might be environmental regulations that require

you to dispose of these batteries properly. Please

contact your local authorities for disposal or recycling

information.

~

Do not overload wall outlets, extension cords or

adaptors beyond their capacity, since this can result in

fire or electric shock.

~

Route power-supply cords so that they are not likely to

be walked on or pinched by items placed on or against

them. Pay particular attention to cords at the plug end,

at wall outlets, and the point where they exit from the

apparatus.

~

To protect this apparatus from a lightning storm, or

when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect

the antenna or cable system. This will prevent damage

to the set due to lightning and power line surges.

~

Before connecting the AC power cord to the DC

adaptor outlet, make sure the voltage designation of

the DC adaptor corresponds to the local electrical

supply.

~

Never insert anything metallic into the open parts

of this apparatus. Doing so may create a danger of

electric shock.

~

To avoid electric shock, never touch the inside of this

apparatus. Only a qualified technician should open this

apparatus.

~

Make sure to plug the power cord in until it is firmly

seated. When unplugging the power cord from a wall

outlet, always pull on the power cord's plug. Never

unplug by pulling on the power cord. Do not touch the

power cord with wet hands.

~

If this apparatus does not operate normally - in

particular, if there are any unusual sounds or smells

coming from it - unplug it immediately and contact an

authorized dealer or service centre.

~

Maintenance of Cabinet.

- Before connecting other components to this

product, be sure to turn them off.

- If you move your product suddenly from a cold place

to a warm place, condensation may occur on the

operating parts and lens and cause abnormal disc

playback. If this occurs, unplug the product, wait for

two hours, and then connect the plug to the power

outlet. Then, insert the disc, and try to play back

again.

~

Be sure to pull the power plug out of the outlet if the

product is to remain unused or if you are leaving the

house for an extended period of time (especially when

children, elderly, or disabled people will be left alone in

the house).

- Accumulated dust can cause an electric shock, an

electric leakage, or a fire by causing the power cord

to generate sparks and heat or the insulation to

deteriorate.

~

Contact an authorized service centre for information

if you intend to install your product in a location with

heavy dust, high or low temperatures, high humidity,

chemical substances, or where it will operate 24 hours

a day such as in an airport, a train station, etc. Failing

to do so may lead to serious damage of your product.

~

Use only a properly grounded plug and wall outlet.

- An improper ground may cause electric shock or

equipment damage. (Class l Equipment only.)

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO

QUALIFIED PERSONNEL.

This symbol indicates that high voltage is

present inside. It is dangerous to make

any kind of contact with any internal part

of this product.

This symbol indicates that important

literature concerning operation and

maintenance has been included with this

product.

✎

The following also applies to the Wireless Receiver Module (SWA-7000).

HT-J7750W-ZK-ENG-0311.indd 2HT-J7750W-ZK-ENG-0311.indd 2 2015-03-11  3:38:142015-03-11  3:38:14

3 - English

Safety Information

~

To turn this apparatus off completely, you must

disconnect it from the wall outlet. Consequently, the

wall outlet and power plug must be readily accessible

at all times.

~

Do not allow children to hang on the product.

~

Store the accessories (battery, etc.) in a location safely

out of the reach of children.

~

Do not install the product in an unstable location such

as a shaky self, a slanted floor, or a location exposed

to vibration.

~

Do not drop or strike the product. If the product is

damaged, disconnect the power cord and contact a

service centre.

~

To clean this apparatus, unplug the power cord from

the wall outlet and wipe the product using a soft,

dry cloth. Do not use any chemicals such as wax,

benzene, alcohol, thinners, insecticide, air fresheners,

lubricants, or detergent. These chemicals can damage

the appearance of the product or erase the printing on

the product.

~

Do not expose this apparatus to dripping or splashing.

Do not put objects filled with liquids, such as vases on

the apparatus.

~

Do not dispose of batteries in a fire.

~

Do not plug multiple electric devices into the same wall

socket. Overloading a socket can cause it to overheat,

resulting in a fire.

~

There is danger of an explosion if you replace the

batteries used in the remote with the wrong type of

battery. Replace only with the same or equivalent type.

WARNING :

~

TO PREVENT THE SPREAD OF FIRE,

KEEP CANDLES AND OTHER ITEMS

WITH OPEN FLAMES AWAY FROM

THIS PRODUCT AT ALL TIMES.

~

To reduce the risk of fire or electric

shock, do not expose this appliance to rain or

moisture.

CLASS 1 LASER PRODUCT

This product is classified as a CLASS 1 LASER product.

Use of controls, adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

CAUTION :

~

INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED, AVOID EXPOSURE TO

BEAM.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

3D Precautions

IMPORTANT HEALTH AND SAFETY INFORMATION FOR

3D PICTURES.

Read and understand the following safety information

before using the 3D function.

~

Some viewers may experience discomfort while viewing

3D TV such as dizziness, nausea, and headaches.

If you experience any such symptom, stop viewing 3D

TV, remove the 3D Active Glasses, and rest.

~

Watching 3D images for an extended period of time

may cause eye strain. If you feel eye strain, stop

viewing 3D TV, remove your 3D Active Glasses, and

rest.

~

A responsible adult should frequently check on children

who are using the 3D function.

If there are any reports of tired eyes, headaches,

dizziness, or nausea, have the child stop viewing 3D

TV and rest.

~

Do not use the 3D Active Glasses for other purposes

(such as general eyeglasses, sunglasses, protective

goggles, etc.)

~

Do not use the 3D function or 3D Active Glasses while

walking or moving around. Using the 3D function or 3D

Active Glasses while moving around may cause you to

bump into objects, trip, and/or fall, and cause serious

injury.

~

If you want to enjoy 3D content, connect a 3D device

(3D compliant AV receiver or TV) to the product’s HDMI

OUT port using a high-speed HDMI cable. Put on 3D

glasses before playing the 3D content.

~

The product outputs 3D signals only through an HDMI

cable connected to the HDMI OUT port.

~

The video resolution in 3D play mode is limited to the

resolution of the original 3D video. You cannot change

the resolution to your preference.

~

Some functions such as BD Wise, screen size

adjustment, and resolution adjustment may not operate

properly in 3D play mode.

~

You must use a high-speed HDMI cable for proper

output of the 3D signal.

~

Stay at least three times the width of the screen from

the TV when watching 3D images. For example, if

you have a 46 inch screen, stay 3.5 meters from the

screen.

~

Place the 3D video screen at eye level for the best 3D

picture.

~

When the product is connected to some 3D devices,

the 3D effect may not function properly.

~

This product does not convert 2D content into 3D.

~

"Blu-ray 3D" and "Blu-ray 3D" logo are trademarks of

the Blu-ray Disc Association.

HT-J7750W-ZK-ENG-0311.indd 3HT-J7750W-ZK-ENG-0311.indd 3 2015-03-11  3:38:152015-03-11  3:38:15

4 - English

Contents

GETTING STARTED

5 Accessories

5 Speaker Components

6 Front Panel

7 Rear Panel

8 Remote Control

CONNECTIONS

9 Connecting the Speakers

12 Connecting to a TV and External Devices

13 Connecting to a Network Router

SETTINGS

14 The Initial Settings Procedure

14 The Home Screen at a Glance

15 Accessing the Settings Screen

15 Settings Menu Functions

21 Radio Setup

22 Network Setup

24 Wi-Fi Direct

25 Upgrading Software

PLAYING CONTENT

27 Playing Commercial Discs

27 Playing Multimedia Files

29 Controlling Video Playback

32 Controlling Music Playback

37 Using Bluetooth

39 Playing Photo Content

41 Using the Special Effects Remote Control

Buttons

NETWORK SERVICES

42 Logging In to Your Samsung Account

42 Before Using SAMSUNG APPS

43 Using SAMSUNG APPS

45 Screen Mirroring

45 Using the Web Browser

49 Linking your Internet Service Accounts to the

Product

49 BD-LIVE™

APPENDIX

50 Additional Information

51 Disk and Format Compatibility

58 Troubleshooting

61 Specifications

63 Licences

Figures and illustrations in this User Manual

are provided for reference only and may differ

from actual product appearance.

HT-J7750W-ZK-ENG-0311.indd 4HT-J7750W-ZK-ENG-0311.indd 4 2015-03-11  3:38:162015-03-11  3:38:16

5 - English

Getting Started

Check the box for the accessories and speaker components listed or shown below.

Accessories

~

Remote Control

~

Lithium Battery

~

User Manual

Power Cable (Main Unit, SWA-7000) x 2

FM Antenna HDMI Cable

WARNING, DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD,

[The remote control supplied with] This product contains a coin/button cell battery.

If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and

can lead to death. Keep new and used batteries away from children. If the battery compartment does not

close securely, stop using the product and keep it away from children. If you think batteries might have been

swallowed or placed inside any part of the body, seek immediate medical attention.

Speaker Components

Speaker Cable x 2

Screw (5x20) x 16

Stand Base x 4 Centre

Front/

Front Top x 2

Stand x 4 Surround x 2 Subwoofer

Wireless Receiver

Module (SWA-7000)

Getting Started

HT-J7750W-ZK-ENG-0311.indd 5HT-J7750W-ZK-ENG-0311.indd 5 2015-03-11  3:38:172015-03-11  3:38:17

6 - English

Getting Started

Front Panel

H

I

G

H

-

E

N

D

V

A

C

U

M

T

U

B

E

S

O

U

N

D

5V 0.5A

DISPLAY ICONS

FUNCTION STOP PLAY/PAUSE

OPEN/

CLOSE

VOLUME

CONTROL

POWER

USBREMOTE CONTROL SENSOR

DISPLAY

VACUUM TUBE AMP

DISC TRAY

✎

Cellular phones or mobile devices placed near the vacuum tube amp or electronic products placed on the

top of the product can cause audio noise or distortion.

✎

When the product is on, do not let children touch the product's surface. It will be hot.

✎

To upgrade the product's software through the USB jack, you must use a USB flash drive.

✎

When the product displays a Blu-ray Disc menu, you cannot start the movie by pressing the button on

the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then

press the OK

button.

✎

If you are using the Internet or are playing content from a USB device on your TV through the home cinema,

you cannot select the BD/DVD mode with the SOURCE button. To select the BD/DVD mode, exit the

Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.

HT-J7750W-ZK-ENG-0311.indd 6HT-J7750W-ZK-ENG-0311.indd 6 2015-03-11  3:38:202015-03-11  3:38:20

7 - English

Getting Started

Rear Panel

HDMI OUT

HDMI IN

1 2

LAN

POWER

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

L

FRONT

R

FRONT TOP

L

FRONT TOP

R

IMPEDANCE : 3

AUX IN FM ANT

OPTICAL

DIGITAL

AUDIO IN

L

R

COOLING FAN

* FM ANTENNAAUX IN

HDMI OUT

HDMI IN

SPEAKER OUTPUT

CONNECTORS

POWER CORD

LAN TERMINAL

EXTERNAL DIGITAL

AUDIO IN (OPTICAL)

* Connecting the FM Antenna

1. Connect the supplied FM antenna to the FM ANT Jack.

2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a

wall or other rigid surface.

✎

Maintain a minimum of 10 cm of clear space on all sides of the home cinema to ensure adequate ventilation.

Do not obstruct the cooling fan or ventilation holes.

✎

This product does not receive AM broadcasts.

HT-J7750W-ZK-ENG-0311.indd 7HT-J7750W-ZK-ENG-0311.indd 7 2015-03-11  3:38:212015-03-11  3:38:21

8 - English

Getting Started

Remote Control

Tour of the Remote Control

✎

While playing multimedia content in SAMSUNG APPS, press and hold

5

button on the remote to pause

playback. To stop playback, press and hold

e

(

EXIT) button on the remote.

Installing batteries in the Remote Control

1

Use a coin to turn the remote

control cover anti-clockwise to

remove it as shown in the figure

above.

2

Insert a 3V lithium battery. Keep

the positive (+) pole upward when

inserting the battery. Put the

battery cover on and align the '●'

marks side by side as shown in

the figure above.

3

Use a coin to turn the cover

clockwise as far as it will go to fix

it in place.

Turn the product on and off.

Adjust the volume.

Press to move to the Home screen.

Press to skip backwards(

[

) or

forwards(

]

)

or

Press and hold to search

backwards(

(

) or forwards(

)

).

Select on-screen menu items and

change menu values.

,.

:

Search for active FM stations

and to change channels.

Return to the previous menu.

Use to enter the Popup menu/Title

menu.

Press to apply sound effects.

Press to record FM radio

broadcasts.

Press to apply the DTS Neo:Fusion II

effect.

These buttons are used both for

menus on the product and also several

Blu-ray Disc functions.

Press to select MANUAL/PRESET in

the Tuner function.

Cut off the sound temporarily.

Press to play disc or files.

or

Press to pause playing.

Press to select the Home Cinema's

mode (HDMI, AUX, BD/DVD, etc.).

Press to use the Tools menu.

or

To display the number keypad (may

include function keys when applicable)

on the screen, press and hold the

button.

Press to stop the disc playing or to exist

the menu.

Use to display the playback information

when playing a Blu-ray/DVD disc or files.

Use to set a preset radio frequency.

Press to view the disc menu.

Set a Sleep time to shut off the product.

Press to open and close the disc tray.

Select STEREO or MONO for radio

broadcasts.

HT-J7750W-ZK-ENG-0311.indd 8HT-J7750W-ZK-ENG-0311.indd 8 2015-03-11  3:38:222015-03-11  3:38:22

9 - English

Connections

This section describes various methods of connecting the product to other external components.

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Surround (L)

Surround (R)

Product

Centre

Subwoofer

Wireless

Receiver Module

Front/

Front Top (L)

Front/

Front Top (R)

Position of the product

Place it on a stand or cabinet shelf,

or under the TV stand.

Selecting the Listening Position

The listening position should be

located about 2.5 to 3 times the

TV's screen size away from the

TV. For example, if you have a 46

inch screen, locate the listening

position 2.92 to 3.50 meters from

the screen.

Front/Front Top

Speakers

Place these speakers in front of your listening position, facing inwards (about

45°) toward you. Place the front speakers so that their tweeters will be at the

same height as your ear. Align the front face of the front/front top speakers with

the front face of the centre speaker or place them slightly in front of the centre

speakers.

Centre Speaker

It is best to install the centre speaker at the same height as the front/front top

speakers. You can also install it directly over or under the TV.

Surround Speakers

Place these speakers to the side of your listening position. If there isn't enough

room, place these speakers so they face each other. Position them about 60 to

90cm above your ear, facing slightly downward.

* Unlike the front and centre speakers, the surround speakers are used mainly

for sound effects. Sound will not come from them all the time.

Subwoofer

The position of the subwoofer is not so critical. Place it anywhere you like.

* Surround speakers must be connected to the wireless receiver module.

* The appearance of your speakers may differ from the illustrations in this manual.

* Each speaker has a coloured label on its back or underside. Each cable has a single coloured band

near its end. Match the band on each cable to the speaker label by colour, and then connect the

cable to the speaker. See page 10 for exact instructions.

Connections

HT-J7750W-ZK-ENG-0311.indd 9HT-J7750W-ZK-ENG-0311.indd 9 2015-03-11  3:38:232015-03-11  3:38:23

10 - English

Connections

Installing the Speakers on the Tallboy Stands

1. Find the speaker cable that is attached to the Stand.

Turn the Stand and Stand Base upside-down, unravel

the speaker cable, and then draw it through the hole in

the Stand Base.

✎

Handle the Stand carefully. It is heavy.

2. Connect the Stand Base to the bottom of the Stand.

3. Insert three 5x20 screws into the marked holes in the

Stand Base, and then tighten them with a screwdriver as

shown in the illustration.

4. Place the speaker cable into the slot on the bottom of

the stand base.

5. Connect the assembled stand and a speaker together by

matching the labels on the stand and speaker with each

other as shown in the picture.

6. Insert a screw (5x20) into the hole on the rear of the

speaker and tighten by turning it clockwise with a

screwdriver.

7. Repeat steps 1 through 6 with the other speaker and

stand.

Speaker Cable Connections

1. Match each speaker cable bundle to the correct speaker by matching the coloured band on each bundle

to the coloured sticker on the bottom or back of each speaker.

2. Connect the speaker wire plugs from each speaker to the back of the product by matching the coloured

band on each cable to the colours of the speaker jacks. When connecting, make sure to match label

colour on the back of speaker.

SURROUND SPEAKERS OUT

52'#-'4+/2'&#0%'š

ID SET

L

R

HDMI OUT

1

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

L

FRONT

R

FRONT TOP

L

FRONT TOP

R

IMPEDANCE : 3

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

L

FRONT

R

FRONT TOP

L

FRONT TOP

R

IMPEDANCE : 3

Centre Speaker

Wireless Receiver Module

Surround Speaker (L)

Surround Speaker (R)

Front Top/

Front Speaker (L)

Front Top/

Front Speaker (R)

Subwoofer

1

3

5 6

4

Speaker

Stand

Stand Base

Stand

2

HT-J7750W-ZK-ENG-0311.indd 10HT-J7750W-ZK-ENG-0311.indd 10 2015-03-11  3:38:242015-03-11  3:38:24

11 - English

Connections

✎

If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic field.

✎

Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too

close to the product, sound from the speakers may be disrupted because of interference.

✎

If you use a device such as a microwave oven, wireless LAN Card, Bluetooth device, or any other device

near the product, sound from the speakers may be disrupted because of interference.

✎

The maximum transmission distance from the product to the wireless receiver module is about 10m, but

may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the

product and the wireless receiver module, the system may not operate at all, because the radio waves

cannot penetrate metal.

✎

If the product doesn't make a wireless connection, you need to run an ID Set between the product and

wireless receiver module. With the product turned off, press and hold (MUTE) button on the remote

control for 5 seconds. Turn on the wireless receiver module. Then, press and hold the "ID SET" button on

the back of the wireless receiver module for 5 seconds, and then turn the product on.

| CAUTION |



If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever

you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each

speaker on a screw or nail.



Do not let children play with or near the speakers. They could get hurt if a speaker falls.



When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.



Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien

substances into the duct (hole) of the subwoofer speaker.



Do not hang the subwoofer on the wall by the duct (hole).



The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and

moisture.



For optimal listening performance, make sure that the area around the wireless receiver module location is

clear of any obstructions.



In 2-CH mode, you will hear no sound from the wireless surround speakers.

HT-J7750W-ZK-ENG-0311.indd 11HT-J7750W-ZK-ENG-0311.indd 11 2015-03-11  3:38:262015-03-11  3:38:26

12 - English

Connections

Connecting to a TV and External Devices

HDMI OUT

HDMI IN

1 2

LAN

AUX IN FM ANT

OPTICAL

DIGITAL

AUDIO IN

L

R

OPTICAL OUT

AUDIO OUTHDMI OUTHDMI IN (ARC)

HDMI OUT

HDMI IN

1 2

LAN

POWER

AUX IN FM ANT

OPTICAL

DIGITAL

AUDIO IN

L

R

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

L

FRONT

R

FRONT TOP

L

FRONT TOP

R

IMPEDANCE : 3

Method 1 Method 3

Method 2

R

Red

W

White

External

Devices

Connecting to a TV

Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. If the

TV supports ARC, you can hear the audio from your TV through the home cinema with only this cable connected.

See page 18 in this manual and the section on ARC in your TV's user's manual for details.

Connecting to External Devices

Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable

Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital

device.



Select the HDMI1 or HDMI2 mode.

Method 2 AUX IN : Connecting an External Analogue Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on

the external analogue component.



Select the AUX mode.

~

Be sure to match the colours on the cable plugs to the colours on the input and output jacks.

Method 3 OPTICAL : Connecting an External Digital Audio Component

Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite

Receivers (Set-Top-Boxes) to the home cinema. Using a digital optical cable (not supplied), connect the Optical

Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital

optical cable.



Select the D. IN mode.

✎

To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.

✎

This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.

✎

This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

Selecting an External Device to Use

To select an external device after you have connected it, press the SOURCE button. Each time you press the

button, the mode changes in this order : BD/DVD



D. IN



AUX



HDMI1



HDMI2



FM



BT

HT-J7750W-ZK-ENG-0311.indd 12HT-J7750W-ZK-ENG-0311.indd 12 2015-03-11  3:38:272015-03-11  3:38:27

13 - English

Connections

Connecting to a Network Router

You can connect your product to your network router

using one of the methods illustrated below.

Wired Network

HDMI OUT

HDMI IN

1 2

LAN

POWER

AUX IN FM ANT

OPTICAL

DIGITAL

AUDIO IN

L

R

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

L

FRONT

R

FRONT TOP

L

FRONT TOP

R

IMPEDANCE : 3

Broadband

service

Broadband

service

Broadband modem

(with integrated router)

Broadband

modem

Router

Or

✎

Your router or your Internet Service Provider's

policies may prevent the product from accessing

Samsung's software update server. If this occurs,

contact your Internet Service Provider (ISP) for

more information.

✎

DSL users, please use a router to make a network

connection.

✎

Try to use the CAT 7 cable to connect.

✎

You cannot use the product if the network speed

is slower than 10Mbps.

✎

To use the DLNA function, you must connect your

PC to your network as shown in the illustrations

above.

The connection can be wired or wireless.

Wireless Network

Broadband

service

Wireless IP sharer

✎

If your wireless IP router supports DHCP, this

product can use a DHCP or static IP address to

connect to the wireless network.

✎

Set your wireless IP router to Infrastructure mode.

Ad-hoc mode is not supported.

✎

The product supports only the following wireless

security key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),

WPA2-PSK (TKIP/AES)

✎

Select a channel on the wireless IP router that is

not currently being used. If the channel set for

the wireless IP router is currently being used by

another device nearby, it will result in interference

and communication failure.

✎

In compliance with the newest Wi-Fi certification

specifications, Samsung home cinemas do not

support WEP, TKIP, or TKIP-AES (WPS2 Mixed)

security encryption in networks running in the

802.11n mode.

✎

Wireless LAN, by its nature, may cause

interference, depending on the operating

conditions (AP performance, distance, obstacles,

interference by other radio devices, etc.).

HT-J7750W-ZK-ENG-0311.indd 13HT-J7750W-ZK-ENG-0311.indd 13 2015-03-11  3:38:292015-03-11  3:38:29

14 - English

Settings

The Initial Settings Procedure

~

The Home menu will not appear if you do not

configure the initial settings.

~

The OSD (On Screen Display) may change in

this product after you upgrade the software

version.

~

The access steps may differ depending on the

menu you selected.

After you have finished connecting the home cinema

to your TV, turn on the TV, and then turn on the

home cinema. The first initial setup screen appears.

The setup screens appear in this order: Language,

Network Configuration, Terms and Conditions, Screen

Resolution (Aspect Ratio). Follow the instructions

displayed on each screen, which will guide you

through the easy setup procedure. When the initial

setup is completed, a tutorial screen guiding the

Home menu will appear. To exit this screen, press the

e

(

EXIT) button on the remote.

✎

To edit your settings after the initial setup, select

Settings > System > Setup in the Home screen

or select the Reset option. (See page 20)

The Home Screen at a Glance

PLAY DISC

App 1 App 2 App 3 App 4 App 5 App 6

Screen Mirroring

Source Settings

MULTIMEDIA

SAMSUNG APPS

No Disc

1 23

45 786

RECOMMENDED MY APPS

1

PLAY DISC

Displays information about the disc currently in the

disc tray. Press

OK to start playing the disc.

2

MULTIMEDIA

Play photos, videos, or music content from Discs,

USB devices, PCs, mobile devices.

3

SAMSUNG APPS

Download/Access various for pay or free-of-charge

applications.

4

RECOMMENDED

A list of useful and popular apps we recommend

you download.

5

MY APPS

Displays downloaded and installed apps. You can

change the display order. (See page 43)

6

Screen Mirroring

Set up the wireless mirroring function between the

home cinema and a smart phone or tablet.

✎

Depending on your country, this menu function

may not be supported.

7

Source

Select the desired source such as Digital In

AUX HDMI IN 1 HDMI IN 2 Tuner (FM Radio)

or Bluetooth depending on what external device

is connected and its status. You can also use the

remote's SOURCE button or the main unit's

button.

8

Settings

Set various functions to suit your personal

preferences.

HT-J7750W-ZK-ENG-0311.indd 14HT-J7750W-ZK-ENG-0311.indd 14 2015-03-11  3:38:302015-03-11  3:38:30

15 - English

Settings



Selecting an Option on the Home Screen

1. To select an option on the Home screen, move

the cursor using the

78:;

buttons until it

highlights the option of your choice, and then

press the

OK button.

✎

If you leave the product in the stop mode for more

than 5 minutes without using it, a screen saver

appear on your TV. If the product is left in the

screen saver mode for more than 20 minutes, the

power will automatically turn off.

Accessing the Settings Screen

1. Select Settings on the Home screen, and then

press OK. The Settings screen appears.

Picture

UHD Output Auto

3D Settings

TV Aspect Ratio

16:9 Original

BD Wise Off

Resolution Auto

Movie Frame (24 fps) Auto

DVD 24 fps Conversion Off

Picture

Sound

Network

Smart Hub

System

Support

Settings

2. To access the menus, sub-menus, and options

on the Settings screen, please refer to the

remote control illustration below.

Buttons on the Remote Control Used

for the Settings Menu

2

4

1

3

1

HOME Button : Press to move to the Home

screen.

2

'

(

RETURN) Button : Press to return to the

previous menu.

3

OK / DIRECTION Button :

~

Press

78:;

to move the cursor or

select an item.

~

Press the OK button to activate the

currently selected item or confirm a

setting.

4

e

(

EXIT) Button : Press to exit the current

menu.

Detailed Function Information

Each Settings function, menu item, and individual

option is explained in detail on-screen. To view an

explanation, use the

78:;

buttons to select the

function, menu item, or option. The explanation will

usually appear on the right of the screen.

A short description of each Settings function

starts below. Additional information on some of the

functions is also in the Appendix of this manual.

Settings Menu Functions

Picture

UHD Output

This option outputs HDMI video at UHD (Ultra High

Definition) resolution. This is only available when

Movie Frame is set to Auto.

✎

To use this feature, you must connect the

product to a device that supports UHD

resolution and you must have content that

plays at 24 fps (film speed).

3D Settings

Set up the 3D related functions.



3D Blu-ray Playback Mode: Select whether to

play a Blu-ray Disc with 3D contents in 3D Mode. If

you move to the Home or Smart Hub Home menu

while in 3D mode, the product will switch to 2D

automatically.



Screen Size: Enter the size of the TV attached to

the product. The product will automatically adjust

the 3D output to the screen size of the TV.

✎

Carefully read the health and safety information

before viewing

3D content. (See page 3)

HT-J7750W-ZK-ENG-0311.indd 15HT-J7750W-ZK-ENG-0311.indd 15 2015-03-11  3:38:322015-03-11  3:38:32

16 - English

Settings

TV Aspect Ratio

Lets you adjust the output of the product to the

screen size of your TV. (See page 50)

BD Wise

BD Wise is Samsung’s latest inter-connectivity

feature.

When you connect a Samsung product and a

Samsung TV with BD Wise to each other via

HDMI, and BD Wise is on in both the product

and TV, the product outputs video at the video

resolution and frame rate of the Blu-ray/DVD Disc.

Resolution

Lets you set the output resolution of the HDMI

video signal to BD Wise, Auto, 1080p, 1080i,

720p, 576p/480p. The number indicates the

number of lines of video per frame. The i and

p indicate interlaced and progressive scan,

respectively.

The more lines, the higher quality.

Movie Frame (24 fps)

Setting the Movie Frame (24 fps) feature to

Auto lets the product adjust its HDMI output to

24 frames per second automatically for improved

picture quality if attached to a 24 fps compatible

TV.

~

You can enjoy the Movie Frame (24 fps) feature

only on a TV supporting this frame rate.

~

Movie Frame is only available when the product

is in the HDMI 1080p output resolution modes.

DVD 24 fps Conversion

Converts DVD playback to 24 frames per second

and outputs it via HDMI. This option is only

available when Movie Frame (24 fps) is set to

Auto.

✎

This feature applies to NTSC discs only.

Fit Screen Size

Lets you select the optimal size for the Smart Hub

or Screen Mirroring Screen.

HDMI Colour Format

Lets you set the colour space format for the HDMI

output to match the capabilities of the connected

device (TV, monitor, etc).

HDMI Deep Colour

Lets you set the product to output video from the

HDMI OUT jack with Deep Colour. Deep Colour

provides more accurate colour reproduction with

greater colour depth.

Progressive Mode

Lets you improve picture quality when viewing

DVDs.

Sound

Speaker Settings



Sound Output : Lets you select which speakers

are active, either the TV's speakers or the home

cinema's speakers.



Settings (Home theatre speakers) : Lets you

adjust the following speaker settings and turn the

test tone on and off so you can test the speakers.

- Volume Level

:

Lets you adjust the relative

loudness of each speaker from 6dB to -6dB.

For example, if you like deep bass, you can

increase the loudness of the subwoofer by

6dB.

- Distance

:

Lets you adjust the relative

distance of each speaker from the listening

position up to 9

meters

. The farther the

distance, the louder the speaker will be.

- Speaker Test

:

Begins a test to set the best

surround sound configuration. Press Stop

Test to stop the test while it is in progress.

✎

Speaker Test Order

Front Left



Front Right



Centre



Surround Left



Surround Right



Front

Top Left



Front Top Right



Subwoofer

HT-J7750W-ZK-ENG-0311.indd 16HT-J7750W-ZK-ENG-0311.indd 16 2015-03-11  3:38:332015-03-11  3:38:33

17 - English

Settings



Speaker Settings (Multiroom Link) : You can

enjoy sound through a remote speaker that is

connected to the home cinema through your

home network. To use the network speaker, select

Multiroom. If there is a network speaker available,

it will appear on the screen.

- Don't Use : The network speaker is not used.

- Multiroom

: The network speaker outputs

audio. All network speakers output the same

audio regardless of channel using the PCM

format only.

✎

SOUND EFFECT and 3D SOUND are not

applied if

Multiroom

is set to on.

✎

The network speaker is not available when

Screen Mirroring is active.

✎

For further details, refer to the Multiroom Link

manual from the web site.

www.samsung.com > Support > Search for the

product name > Multiroom Link > Download PDF

Sound Customiser

Sound Customiser lets you calibrate the home

cinema for the optimal sound quality based on

your hearing level and the ambient conditions.

To create a Custom Sound Profile, follow these

steps:

1. In the Sound Customiser Menu, select Add

Custom Sound.

2. On the next screen, select Start. The Preview

screen appears.

3. Select Preview to preview the Test Sound.

Select Next, and then press OK to continue.

4. A 6-step test will start. During each stage,

the TV will sound a test tone at a different

frequency. The tone will begin softly and

increase in volume. Select Yes when you can

hear the test tone. If you want to listen to it

again, select Retry. Each time you select

Yes, the TV will move on to the next tone.

Once the test is complete, a screen appears

that lets you compare the original sound to

the calibrated sound.

5. Select Next, and then press the OK button to

continue. The on-screen keyboard appears

with a default profile name.

6. Enter a name for the calibrated sound profile

or accept the default name, select Done, and

then press the

OK button.

7. Select Done on the next screen, and then

press the OK button. The Sound Customiser

screen reappears.



Custom Sound Profile : Select a Sound Profile

you created to activate it. Or select Hearing

Impaired, a Custom Sound Profile especially

composed of large sounds for those with hearing

disorders.

✎

If there are more than 3 Custom Sounds

registered, Family mode will be activated

which is composed of the average value of all

registered profiles.



Add Custom Sound : Create and add a new

Custom Sound Profile. See the instructions

above.



Edit Custom Sound : Choose a Custom Sound

Profile to modify it. Follow the same steps you

used when creating a sound profile. This function is

only available if you have added a Custom Sound

Profile using Add Custom Sound. (See above.)



Manage Custom Sound : Rename or delete

Custom Sound Profiles. This function is only

available if you have added a Custom Sound

Profile using Add Custom Sound. To select a

profile, highlight the check box to the right of the

profile, and then select Rename or Delete.

Equaliser

Lets you configure the Equaliser settings manually.

Smart Volume

Lets you set the product so that the volume

remains stable when a scene change occurs or

when you change the channel.

HT-J7750W-ZK-ENG-0311.indd 17HT-J7750W-ZK-ENG-0311.indd 17 2015-03-11  3:38:342015-03-11  3:38:34

18 - English

Settings

Audio Return Channel

Lets you direct the sound from the TV to the Home

Cinema speakers. Requires an HDMI connection

and an Audio Return Channel (ARC) compatible

TV.

~

If Audio Return Channel is set to On and you

are using an HDMI cable to connect the product

to the TV, digital optical input is disabled.

~

If Audio Return Channel is set to Auto and you

are using an HDMI cable to connect the product

to the TV, ARC or digital optical input is selected

automatically.

Digital Output

Lets you set the Digital Output to match the

capabilities of the AV receiver you’ve connected to

the product. For more details, please refer to the

digital output selection table. (See page 56)

Dynamic Range Control

Lets you apply dynamic range control to Dolby

Digital, Dolby Digital Plus, and Dolby TrueHD audio.



Auto: Automatically controls the dynamic range

of Dolby TrueHD audio, based on information in

the Dolby TrueHD soundtrack. Also turns dynamic

range control off for Dolby Digital and Dolby Digital

Plus.



Off: Leaves the dynamic range uncompressed,

letting you hear the original sound.



On: Turns dynamic range control on for all three

Dolby formats. Quieter sounds are made louder

and the volume of loud sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix method

that is compatible with your stereo system. You

can choose to have the product downmix to

Normal Stereo or to Surround Compatible.

Audio Sync

When the product is attached to a digital TV, lets

you adjust the audio delay so that the audio syncs

with the video. You can set the delay between 0

and 300 milliseconds.

✎

The Auto function in Audio Sync is guaranteed

to work only with a Samsung TV that supports

the ARC function (the Anynet+ function).

Network

Network Status

Lets you check the current network and Internet

status.

Network Settings

Lets you configure the network connection so

you can enjoy various features such as Internet

services or DLNA Wi-Fi functionality, and perform

software upgrades.

Wi-Fi Direct

Lets you connect a Wi-Fi Direct device to the

product using a peer-to-peer network, without the

need for a wireless router. Note that if the product

is connected to a wireless network, it may be

disconnected when you use Wi-Fi Direct. (See

page 24)

✎

Text files, such as files with a .TXT or .DOC

extension, will not display when you are using the

Wi-Fi Direct function.

Multimedia Device Settings

Allow other devices on your network, such as smart

phones and tablets, to share content with your

product.

Device Name

Lets you assign an identifying name to the product.

You use this name to identify the product when

you are connecting external Wi-Fi devices (smart

phones, tablets, etc.) to it.

HT-J7750W-ZK-ENG-0311.indd 18HT-J7750W-ZK-ENG-0311.indd 18 2015-03-11  3:38:342015-03-11  3:38:34

19 - English

Settings

BD-Live Settings

Lets you set various BD-Live functions. BD-Live

allows you to access extra features available on

some Blu-ray Discs if you are connected to the

Internet.



BD-Live Internet Connection : Lets you fully

allow, partly allow, or prohibit a BD-Live Internet

connection.



BD Data Management : Manage BD data

downloaded from a BD-Live service or Blu-ray

Disc.

✎

To use BD-Live, you must insert a USB storage

device into the home cinema's USB port.

Smart Hub

Caption

Use to modify captions on VOD playback that

supports closed captions. Lets you change

displayed caption's font colour and size.

✎

The Caption function does not work with VOD

services that don't support closed captions.

For some VOD services that do support closed

captions, the functions settings may not be

applied.

✎

Depending on your country, this menu function

may not be supported.

Terms & Policy

Samsung account Terms and Conditions,

Privacy Policy

You can view the terms of use and privacy policy

for Smart Hub, Samsung accounts, and various

other services.

Reset Smart Hub

Resets all Smart Hub settings to their default

settings. To use, you must enter the security PIN.

Press and hold the 123 button until the Num pad

appears on the screen. When the Num pad appears,

select a number using the

78:;

button and then

press the

OK

button.

✎

The default security PIN is 0000.

System

Setup

Lets you re-run the Initial Settings procedure.

Refer to the descriptions displayed on the screen.

Quick start

Lets you set the product to turn on quickly by

decreasing the boot time.

✎

If this function is set to On, Standby power

consumption will increase. (About 12W ~ 20W)

Language

Lets you select the language you prefer for the on-

screen menu, disc menu, audio, subtitles, etc.

~

The language you select for the disc menu,

disc audio, or subtitles will only appear if it is

supported on the disc.

Device Manager

Lets you connect a wireless USB keyboard or mouse

to the USB port on the front of the product.



Keyboard Settings: Lets you configure a

wireless USB keyboard connected to the

product.

✎

You can use the keyboard only when a

QWERTY keyboard screen or window appears

in the Web Browser.



Mouse Settings: Lets you configure a wireless

USB mouse connected to the product. You can

use the mouse in the product's menu in the

same way you use a mouse on your PC.



To use a mouse with the product's menu:

1. Connect the USB mouse to the product.

2. Click the primary button you selected in

Mouse Settings. The Simple Menu appears.

3. Click the menu options you want.

✎

Some USB HID keyboards and mice may not

be compatible with your product.

✎

Some HID keyboard keys may not work.

✎

Wired USB keyboards are not supported.

✎

Some applications may not be supported.

HT-J7750W-ZK-ENG-0311.indd 19HT-J7750W-ZK-ENG-0311.indd 19 2015-03-11  3:38:352015-03-11  3:38:35

20 - English

Settings

✎

If a wireless HID Keyboard does not operate

because of interference, move the keyboard

closer to the product.

Security

Press and hold the 123 button until the Num pad

appears on the screen. When the Num pad appears,

select a number using the

78:;

button and then

press the

OK

button.

The default security PIN is

0000. Enter the default PIN to access the security

function if you haven't created your own PIN.



BD Parental Rating: Prevents playback of

Blu-ray Discs with a rating equal to or above a

specific age rating you have set unless you enter

the PIN.



DVD Parental Rating: Prevents playback of

DVDs with a rating above a specific numerical

rating you have set unless you enter the PIN.



Change PIN: Lets you change the 4-digit PIN used

to access security functions.



If you forget your PIN

1. Remove any disc or USB storage device.

2. Press and hold the

@

button on the front

panel for 5 seconds or more.

All settings will revert to the factory default

settings.

✎

When the factory default settings are restored,

all the user stored BD data is deleted.

General

Lets you specify the display brightness and time

zone.



Front Display: Lets you change the brightness

of the front panel.



Time Zone: You can specify the time zone that

is applicable to your area.



Menu Transparency: Lets you adjust the

transparency of the menu box.

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers linked

operations with other Samsung products that have

the Anynet+ feature, and lets you control those

products with one Samsung TV remote. To operate

this function, you must connect this product to an

Anynet+ Samsung TV using an HDMI cable.

To use an Anynet+ (HDMI-CEC) function, follow

the instructions below.

1) Connect the product to an Anynet+ (HDMI-

CEC)-compliant Samsung TV using HDMI

Cable.

2) Set the Anynet+ (HDMI-CEC) feature to On in

both the TV and the product.

3) Search for and then select the product in the

TV's Anynet+ (HDMI-CEC) list. For more exact

instructions, see the Anynet+ section of the TV's

user's manual.

DivX® Video On Demand

View DivX® VOD Registration Codes to purchase

and play DivX® VOD contents.

Support

Remote Management

When activated, lets Samsung Call Centre agents

diagnose and fix problems with the product

remotely. Requires an active Internet connection.

Remote Management service might not be

available in some countries.

Software Update

For more information about the Software Update

function, see "Upgrading Software" on page 25.

Usage Mode

Lets you set the Usage Mode. If you are using the

home cinema at home, always select Home Use.

Store Demo is for retail display settings only.

Contact Samsung

Provides contact information for assistance with

your product.

Reset

Reverts all settings to their defaults except for the

network and Smart Hub settings. Requires that

you enter your security PIN.

Press and hold the 123

button until the Num pad appears on the screen.

When the Num pad appears, select a number using

the

78:;

button and then press the

OK

button.

The default security PIN is 0000.

HT-J7750W-ZK-ENG-0311.indd 20HT-J7750W-ZK-ENG-0311.indd 20 2015-03-11  3:38:352015-03-11  3:38:35

ページが読み込まれています...

Samsung HT-J7750W ユーザーマニュアル

Samsung HT-J7750W ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント