English ......................................................................................... 2
China: 800-820-6565
Visit www.hamiltonbeach.cn for our complete line of products and Use and Care Guides
– as well as delicious recipes, tips, and to register your product online!
............................................................................................ 14
800-82 0-6565
www.hamiltonbeach.cn
–
www.hamiltonbeach.cn
Irons
电熨斗
840216002
READ BEFORE USE
14014-CN
14015-CN
14016-CN
When using an iron, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING
1. Only use an iron for its intended use.
2. To avoid the risk of electric shock, do not immerse the iron
in water or other liquids.
3. Always turn the iron to OFF before plugging or unplugging
the iron from the electrical outlet. Never pull on the cord to
disconnect the iron from the electrical outlet; instead, grasp
the plug and pull on the plug to disconnect the iron.
4. Do not let the cord touch hot surfaces. Let the iron cool
completely before putting the iron away. Coil the cord loosely
around the iron when storing.
5. Always disconnect the iron from the electrical outlet before filling
the iron with water, emptying the water from the iron, and when
the iron is not in use.
6. Do not operate the iron with a damaged cord or in the event the
iron has been dropped or damaged or there are visible signs of
damage or it is leaking. To avoid the risk of electric shock, do
not disassemble the iron. Take it to a qualified serviceman for
examination and repair. Incorrect assembly might result in a
risk of electric shock when the iron is used after reassembly.
7. The iron must be used and rested on a stable surface.
8. When placing the iron on its stand, ensure that the surface on
which the stand is placed is stable.
9. Close supervision is required for any appliance used by or near
children. Do not leave the iron unattended while the iron is
connected or on an ironing board.
10. Burns can occur from touching hot metal parts, hot water, or
steam. Use caution when you turn a steam iron upside down—
there might be hot water in the reservoir.
IMPORTANT SAFETY INSTRUCTIONS
2
3
OTHER CONSUMER SAFETY INFORMATION
This appliance is intended for household use only.
Use the iron on an ironing board. Ironing on any other surface may
damage that surface.
Do not iron or vertical steam clothes that are being worn.
Do not use vertical steam in the direction of people or pets.
Please Read Before First Use:
• During first use of the iron, it may appear to smoke. This will stop
and does not indicate a defect or hazard.
• Many irons spit or sputter during the first few uses with tap water.
This happens as the steam chamber becomes conditioned. This
will stop after a few uses.
• To clean steam vents before first use, prepare iron for steam iron-
ing; then iron over an old cloth for a few minutes while letting the
iron steam. Press the Blast of Steam button several times to clean
the vents. Then follow the Self-Cleaning instructions on page 11.
SAVE THESE INSTRUCTIONS
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate an iron on the same
circuit with another high-wattage appliance.
2. If an extension cord is absolutely necessary, a cord with an
ampere rating equal to or greater than the maximum rating of
the iron shall be used. A cord rated for less amperage can result
in a risk of fire or electric shock due to overheating. Care shall
be taken to arrange the cord so that it cannot be pulled or be
tripped over.
Parts and Features
MAX
Steam
OFF
Position
Steam
ON
Position
4
Blast of
Steam Button
Water Fill
Opening
Adjustable
Steam
Control
Blast of
Steam Button
Self-Clean
Swivel
Power
Cord
Heel Rest
Temperature
Control Dial
Soleplate
Spray
Trigger
Power On
Light
5
This iron is equipped with a position/motion sensor. This
means that if the iron is left motionless it will turn off automati-
cally and cool to room temperature.
To restart iron, simply move the iron and allow it to reheat on
heel position.
The iron will reheat to the previously selected setting.
Iron Position
Resting on soleplate
Resting on either
side
Resting on heel
Sensor Control
Position Sensing
The iron will turn off automatically when left in the following
positions.
The auto off time varies based on the iron’s position.
Auto Shutoff Reset Light
After 30 seconds of no movement in the horizontal position,
the iron will automatically shut off and the red light will blink.
Move iron upright to vertical position to turn back on.
Motionless Time
33 seconds
33 seconds or
18 minutes
depending on
exact orientation
18 minutes
1. Plug the iron into outlet.
2. Set Adjustable Steam Control to
0 (Dry Iron).
3. Turn Temperature Control Dial to
desired temperature. Allow 2 minutes for
iron to reach desired temperature.
4. To turn iron off, turn Temperature
Control Dial to OFF and unplug iron.
To Dry Iron
6
Iron
High Temp
Setting
Med Temp
Setting
Low Temp
Setting
Fabric care labels on garments have symbols that show
ironing instructions and recommended temperature settings.
These symbols are shown below along with their meaning.
Do Not
Iron
Do Not
Use Steam
Fabric Care Label Symbols
DRY IRON: Synthetics, Silk/Wool (reverse side of fabric)
STEAM IRON:
Cotton (while damp; use steam or spray)
Linen (while damp on reverse side of fabric)
NOTE: To prevent possible garment damage, we do not
recommend ironing fabrics labeled “Dry Clean Only.”
7
To Steam Iron
1. Unplug iron. Set Adjustable Steam Control to 0 (Dry Iron).
Hold iron with soleplate parallel to the ground.
2. Using a cup, slowly pour tap water into water fill opening
until MAX fill line is reached. Do not fill iron directly from
the faucet.
3. Plug iron into outlet.
4. Turn Temperature Control Dial to desired fabric setting in
the steam range.
5. Allow 2 minutes for the iron to reach
desired temperature.
6. Set Adjustable Steam Control to desired
steam setting.
7. To turn iron off, set Set Adjustable
Steam Control to 0 (Dry Iron). Turn
the Temperature Control Dial to OFF.
Unplug iron.
8. Empty water from the iron following directions in “Care
and Cleaning.”
Water: Please use ordinary tap water. If you have extremely
hard water, alternate between tap water and distilled water
for use in the iron.
8
To Vertical Steam
1. Follow Steps 1 through 5 in
“To Steam Iron.”
2. Hang garment in a location that is
not susceptible to damage from heat
or moisture. Do not hang in front of
wallpaper, window, or mirror.
3. Hold iron about 6 inches (15 cm) away
from garment and press and release
the Blast of Steam Button to steam out
wrinkles. Do not press Blast of Steam
Button more than once every 5 seconds.
4. To turn iron off, turn Temperature Control Dial to OFF.
Unplug iron.
5. Empty water from the iron following directions in “Care
and Cleaning.”
NOTICE: Do not allow hot soleplate to touch delicate gar-
ments.
9
Power On Light
The red light stays on even
if Temperature Control Dial
is turned to OFF. Light flashes
if position sensor is activated.
Blast of Steam Button
Push Blast of Steam Button for
an extra blast of steam.
Adjustable Steam Control
This control adjusts the steam
to desired steam level.
Features
10
Care and Cleaning
Iron Storage
1. The water tank of your iron should be emptied after each
use. Turn Temperature Control Dial to OFF. Unplug the
iron and hold over a sink. Slowly tilt pointed end of iron
down over sink. Water will run out of water fill opening.
2. After iron has completely cooled, wrap cord loosely around
iron and store in an upright position. Do not store iron lay-
ing flat on soleplate.
Soleplate
1. Never iron over zippers, pins, metal rivets, or snaps, since
these may scratch the soleplate.
2. To clean occasional buildup on the soleplate, wipe with
a sudsy cloth. Do not use abrasive cleansers or metal
scouring pads.
3. Always store iron upright in the heel rest position.
Spray Trigger
Press Spray Trigger to release
a fine spray of water for difficult
wrinkles in cotton or linen.
Features (cont.)
11
Caring and Cleaning (cont.)
Self-Clean
To keep the steam vents clear of any buildup, follow these
instructions each time you iron using steam.
1. Set Temperature Control Dial to OFF. Fill iron with water
to 1/2 of its maximum capacity.
2. Set Adjustable Steam Control to 0 (Dry Iron). Set Temperature
Control Dial to High temperature setting and let iron heat for
2 minutes.
3. Set Temperature Control Dial to OFF. Unplug iron and hold
over a sink with soleplate facing down.
4. Press and hold the Self-Clean Button. Boiling water and
steam will flow out of steam vents. Allow all water to drain
from iron.
5. Gently move iron front to back to allow water to clean
entire soleplate area.
6. If water still remains inside of soleplate, reheat iron as
indicated in Step 2. Boiling water and steam could still
flow out of steam vents.
Troubleshooting
Iron won’t
heat
PROBLEM
THINGS TO CHECK
• Is the iron plugged in and the outlet working?
Check the outlet by plugging in a lamp.
• Is the Temperature Control Dial turned to a
High, Medium, or Low setting?
• If automatic shutoff model, is the Auto Shutoff
Light flashing? Move the iron to reset.
12
PROBLEM
THINGS TO CHECK
Water is
leaking
Iron
won’t
steam
Leaves
spots
• Do not overfill the water tank.
• If steam ironing, is
Adjustable Steam Control
in a steam position, the Temperature Control
Dial in the steam range, and did the iron have
enough time to preheat?
• If dry ironing, make sure the
Adjustable Steam
Control is in the 0 (Dry Iron) position.
• If using the Blast of Steam Button, push button
less frequently.
• Follow the self-cleaning instructions one or
two times with tap water (not distilled) to
“condition” the iron.
• Check the water level.
• Is
Adjustable Steam Control in Steam position?
• Has the iron had enough time to preheat?
• Anti-drip feature will not allow steam when
temperature setting is in the dry range.
• ALWAYS empty the water tank of the iron
after using. Water left in the tank may discolor
clothing and soleplate.
• If the iron cord should become twisted, unplug
iron and let cool. Hold iron cord in the middle
of entire length. Let plug and iron dangle freely
until cord uncoils. This will extend the life of
your iron cord.
• Check Temperature Control Dial is set to
correct fabric.
Twisted
cord
Troubleshooting (cont.)
Wrinkles
are not
removed
13
Troubleshooting (cont.)
PROBLEM
THINGS TO CHECK
Iron is too
hot/not hot
enough
• Check Temperature Control Dial and adjust
to desired setting level. Let iron cool down
5 minutes before continuing.
Fabric Setting Chart
NOTE: To prevent possible garment damage, we do not
recommend ironing fabrics labeled “Dry Clean Only.”
To Iron
Off
Nylon
Acrylic
Silk
Polyester
Rayon
Wool
Cotton
Linen
Ironing Instructions
Steam
Setting
Dry iron on the wrong side of the fabric.
Dry iron on the wrong side of the fabric.
Dry iron on the wrong side of the fabric.
Iron with fabric still damp.
Iron on the wrong side of fabric.
Steam iron on the wrong side of fabric.
Iron while still damp using steam
and/or spray.
Iron on wrong side of fabric while still
damp.
0
1.
2.
3.
(OFF)
4.
5.
6.
7.
8.
9.
10.
14
15
•
•
•
23
1.
2.
MAX
16
17
/
30
33
33 18
18
1.
2. 0
3.
4.
OFF
18
/
19
1. 0
2.
3.
4.
5.
6.
7.
0
OFF
8.
20
1. 1 5
2.
3. 6 15
5
4. OFF
5.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Hamilton 14016-CN Instructions Manual
- カテゴリー
- アイロン
- タイプ
- Instructions Manual
他の言語で
- English: Hamilton 14016-CN