Dell PowerConnect 7048 クイックスタートガイド

Dell PowerConnect

7000 Series Switch

Getting Started Guide

使用入门指南

入門指南

Guide de mise en route

Handbuch zum Einstieg

Panduan Pengaktifan

はじめに

시작 안내서

Guía de introducción

Başlangıç Kılavuzu

Guia de Primeiros Passos

Regulatory models: PC7024, PC7024P,

PC7024F, PC7048, PC7048P, and PC7048R

Dell PowerConnect

7000 Series Switch

Getting Started Guide

Regulatory Models: PC7024, PC7024P,

PC7024F, PC7048, PC7048P, PC7048R,

and PC7048R-RA

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, PowerConnect™, and OpenManage™ are

trademarks of Dell Inc. Microsoft

®

, Windows

®

, Windows Server

®

, MS-DOS

®

and Windows Vista

®

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or

other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Models: PC7024, PC7024P, PC7024F, PC7048, PC7048P, PC7048R, and PC7048R-RA

March 2011 P/N D3R71 Rev. A00

Contents 3

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 5

PowerConnect 7000 Series Overview . . . . . . . . . . . 5

2 Hardware Overview. . . . . . . . . . . . . . . . . . 6

PowerConnect 7000 Series Front Panel . . . . . . . . . . 6

Switch Ports

. . . . . . . . . . . . . . . . . . . . . 9

Console Port

. . . . . . . . . . . . . . . . . . . . . 9

Out-of-Band Management Port

. . . . . . . . . . 10

USB Port

. . . . . . . . . . . . . . . . . . . . . . 10

Reset Button

. . . . . . . . . . . . . . . . . . . . 10

Port and System LEDs

. . . . . . . . . . . . . . . 10

Stack Master LED and Stack

Number Display

. . . . . . . . . . . . . . . . . . . 11

PowerConnect 7000 Series Back Panel

. . . . . . . . . 11

Expansion Slots for Plug-in Modules

. . . . . . . . 12

Power Supplies

. . . . . . . . . . . . . . . . . . . 12

Ventilation System

. . . . . . . . . . . . . . . . . 13

Locator LED

. . . . . . . . . . . . . . . . . . . . . 13

4 Contents

3Installation. . . . . . . . . . . . . . . . . . . . . . . 14

Site Preparation . . . . . . . . . . . . . . . . . . . . . 14

Unpacking the Switch

. . . . . . . . . . . . . . . . . . 14

Package Contents

. . . . . . . . . . . . . . . . . . 14

Unpacking Steps

. . . . . . . . . . . . . . . . . . 15

Mounting the Switch

. . . . . . . . . . . . . . . . . . . 15

Installing in a Rack

. . . . . . . . . . . . . . . . . 15

Installing as a Free-standing Switch

. . . . . . . . 17

Stacking Multiple Switches

. . . . . . . . . . . . . . . 17

Creating a Switch Stack

. . . . . . . . . . . . . . 17

4 Starting and Configuring the Switch . . . 19

Connecting a Switch to a Terminal . . . . . . . . . . . 20

Connecting a Switch to a Power Supply

. . . . . . . . 22

AC and DC Power Connection

. . . . . . . . . . . 22

Booting the Switch

. . . . . . . . . . . . . . . . . . . . 23

Performing the Initial Configuration

. . . . . . . . . . . 23

Enabling Remote Management

. . . . . . . . . . . 24

Initial Configuration Procedure

. . . . . . . . . . . 24

Example Session

. . . . . . . . . . . . . . . . . . 25

Next Steps

. . . . . . . . . . . . . . . . . . . . . 29

5 PoE Power Budget . . . . . . . . . . . . . . . . . 30

Getting Started Guide 5

Introduction

This document provides basic information about the Dell PowerConnect

7000 Series switches, including how to install a switch and perform the initial

configuration. For information about how to configure and monitor switch

features, see the User’s Configuration Guide, which is available on your User

Documentation CD, or check the Dell Support website at support.dell.com

for the latest updates on documentation and firmware.

This document contains the following sections:

• Hardware Overview

• Installation

• Starting and Configuring the Switch

PowerConnect 7000 Series Overview

The PowerConnect 7000 Series switches are stackable Layer 3 Gigabit

Ethernet switches and include the following six models:

• PowerConnect 7024 (PC7024)

• PowerConnect 7024P (PC7024P)

• PowerConnect 7024F (PC7024F)

• PowerConnect 7048 (PC7048)

• PowerConnect 7048P (PC7048P)

• PowerConnect 7048R (PC7048R/PC7048R-RA)

NOTE: The PowerConnect 7048R (PC7048R/PC7048R-RA) is a top-of-rack switch.

The difference between the PC7048R and PC7048R-RA models is the air-flow

direction.

6 Getting Started Guide

Hardware Overview

This section contains information about device characteristics and modular

hardware configurations for the PowerConnect 7000 Series switches.

All models are 1U, rack mountable switches with the following physical

dimensions:

• 440 x 460 x 44 mm (W x D x H).

• 17.3 x 18.1 x 1.7 inch (W x D x H).

PowerConnect 7000 Series Front Panel

The following images show the front panels of the six switch models in the

PowerConnect 7000 Series.

Figure 1-1. PowerConnect 7024 with 24 10/100/1000BASE-T Ports

Figure 1-2. PowerConnect 7024P with 24 10/100/1000BASE-T PoE Plus Ports

Combo Ports10/100/1000BASE-T Auto-sensing

Full Duplex RJ-45 Ports

Combo Ports10/100/1000BASE-T RJ-45 PoE Plus Ports

Providing up to 30W per Port

Getting Started Guide 7

Figure 1-3. PowerConnect 7024F with 24 SFP Ports

Figure 1-4. PowerConnect 7048 with 48 10/100/1000BASE-T Ports

Figure 1-5. PowerConnect 7048P with 48 10/100/1000BASE-T PoE Plus Ports

SFP Ports Combo Ports

Combo Ports10/100/1000BASE-T Auto-sensing

Full Duplex RJ-45 Ports

Combo Ports10/100/1000BASE-T RJ-45 PoE Plus Ports

Providing up to 30W per Port

8 Getting Started Guide

Figure 1-6. PowerConnect 7048R with 48 10/100/1000BASE-T Ports

In addition to the switch ports, the front panel of each model in the series

includes the following ports:

• Console port

• Out-of-band management port

• USB port

The additional ports are on the right side of the front panel.

Figure 1-7. Additional PowerConnect 7000 Series Ports

Combo Ports

10/100/1000BASE-T Auto-sensing

Full Duplex RJ-45 Ports

Combo Ports

Reset Button

USB Port

Console Port Out-of-Band Management Port

Getting Started Guide 9

The front panel also contains a reset button (pinhole) and several status

LEDs.

NOTE: The port LEDs and system LEDs on the front panel are not the same for all

models. Figure 1-7 shows the LEDs on the PowerConnect 7024, PowerConnect

7024F, and PowerConnect 7048 switches.

Switch Ports

The PowerConnect 7024 and PowerConnect 7024P front panel provides

24 Gigabit Ethernet (10/100/1000BASE-T) RJ-45 ports with four SFP combo

ports that have an auto-sensing mode for speed, flow control, and duplex

mode. SFP transceivers are sold separately. The PowerConnect 7024P switch

ports are IEEE 802.3at-2009-compliant (PoE Plus) and can provided up to

30W of power per port.

The PowerConnect 7024F front panel provides 20 Gigabit Ethernet

(10/100/1000BASE-FX) SFP ports plus 4 combo ports for copper or SFP

media support.

The PowerConnect 7048, PowerConnect 7048P, and PowerConnect 7048R

front panel provides 48 Gigabit Ethernet (10/100/1000BASE-T) RJ-45 ports

with four SFP combo ports. The PowerConnect 7048P switch ports are

IEEE 802.3at-2009-compliant (PoE Plus) and can provided up to 30W of

power per port.

The front-panel switch ports have the following characteristics:

• The switch automatically detects the difference between crossed and

straight-through cables on RJ-45 ports.

• SFP ports support both SX and LX modules.

• RJ-45 ports support half- and full-duplex mode 10/100/1000 Mbps.

Console Port

The console port is for management through a serial interface. This port

provides a direct connection to the switch and allows you to access the CLI

from a console terminal connected to the port through the provided serial

cable (RJ-45 to female DB-9 connectors).

The console port supports asynchronous data of eight data bits, one stop bit, no

parity bit, and no flow control. The default baud rate is 9600 bps.

10 Getting Started Guide

Out-of-Band Management Port

The Out-of-Band (OOB) management port is a 10/100/1000BASE-T

Ethernet port dedicated to remote switch management. Traffic on this port is

segregated from operational network traffic on the switch ports and cannot be

switched or routed to the operational network.

USB Port

The Type-A, female USB port supports a USB 2.0-compliant flash memory

drive. The PowerConnect switch can read or write to a flash drive formatted

as FAT-32. You can use a USB flash drive to copy switch configuration files

and images between the USB flash drive and the switch. You can also use the

USB flash drive to move and copy configuration files and images from one

switch to other switches in the network.

The USB port does not support any other type of USB device.

Reset Button

The reset button is accessed through the pinhole and allows you to perform a

hard reset on the switch. To use the reset button, insert an unbent paper clip

or similar tool into the pinhole. When the switch completes the boot process

after the reset, it resumes operation with the most recently saved

configuration. Any changes made to the running configuration that were not

saved to the startup configuration prior to the reset are lost.

Port and System LEDs

The front panel contains light emitting diodes (LEDs) that indicate the

status of port links, power supplies, fans, stacking, and the overall system.

Additionally, the PowerConnect 7024P and PowerConnect 7048P switches

contain LEDs that provide information about Power over Ethernet Plus

(PoE+) status and activity on the ports.

For information about the status that the LEDs indicate, see the User’s

Configuration Guide.

Getting Started Guide 11

Stack Master LED and Stack Number Display

When a switch within a stack is the master unit, the stack master LED, which

is labeled M, is solid green. If the M LED is off, the stack member is not the

master unit. The Stack No. panel displays the unit number for the stack

member. If a switch is not part of a stack, the M LED is illuminated and the

stack unit number is 1.

PowerConnect 7000 Series Back Panel

The following images show the back panel of the PowerConnect 7000 Series

switches.

Figure 1-8. PC7024, PC7024F, and PC7048 Back Panel

Figure 1-9. PC7024P and PC7048P Back Panel

Dual 10G Slots for SFP+, 10GBASE-T,

or Stacking/10GbE Modules

AC Power

Receptacle

Redundant DC Power

Supply Receptacle

Fan Vents

AC Power

Receptacle

External DC Power

Supply Receptacle

Fan Vents

Dual 10G Slots for SFP+, 10GBASE-T,

or Stacking/10 GbE Modules

12 Getting Started Guide

Figure 1-10. PC7048R Back Panel

Expansion Slots for Plug-in Modules

Two expansion slots are located on the back of the switch and can support the

following modules:

• 10GBASE-T module

• SFP+ module

• Stacking/10 GbE module

Each plug-in module has two ports. The Stacking/10GbE modules can be

configured to operate as either 16-Gigabit stacking ports or 10-Gigabit

Ethernet switch ports. The plug-in modules include hot-swap support, so you

do not need to reboot the switch after you install a new module.

Power Supplies

PC7024 and PC7024F

PowerConnect 7024 and PowerConnect 7024F switches have an internal

180-watt power supply. The additional external power supply (PowerConnect

RPS720) provides 180 watts of power and gives full redundancy for the

switch.

PC7024P

PowerConnect 7024P switches have an internal 1000-watt power supply.

The additional external power supply (PowerConnect MPS1000) provides

1000 Watts and gives full redundancy for the switch.

AC Power

Receptacle

Fan Trays

AC Power

Receptacle

Dual 10G Slots for SFP+, 10GBASE-T,

or Stacking/10GbE Modules

Getting Started Guide 13

PC7048

PowerConnect 7048 switches have an internal 180-watt power supply.

The additional external power supply (PowerConnect RPS720) provides

180 watts and gives full redundancy for the switch.

PC7048P

PowerConnect 7048P switches have an internal 1000-watt power supply

which can support up to 24 ports of PoE. The additional external power

supply (PowerConnect MPS1000) allows all 48 ports of PoE, or 24 ports of

PoE and full redundancy for the switch.

PC7048R and PC7048R-RA

PowerConnect 7048R and PowerConnect 7048R-RA switches are designed as

top-of-rack switches and include two internal, replaceable, AC power supplies

for redundant or load-sharing operation. Each power supply can provide

300 watts and includes hot-swap support. This means you do not need to

power-down the switch to remove or replace one power supply while the other

power supply is operating normally. However, it is necessary to remove power

from the power supply that is being removed or replaced.

CAUTION: Remove the power cable from the modules prior to removing the

module itself. Power must not be connected prior to insertion in the chassis.

Ventilation System

Three fans cool the PowerConnect 7024, PowerConnect 7024F, and

PowerConnect 7048. The PowerConnect 7024P and PowerConnect 7048P

each have two fans, with a third fan in the internal power supply.

The PowerConnect 7048R has two hot-swappable fan trays with one fan each.

Locator LED

The back panel includes an LED to help identify the switch within a rack or

room full of switches. From your remote management system, you can set the

LED to blink to help you or a local technician identify the physical location of

the switch.

14 Getting Started Guide

Installation

Site Preparation

PowerConnect 7000 Series switches can be mounted in a standard 48.26-cm

(19-inch) rack or left freestanding (placed on a flat surface) and function as

stand-alone switches.

Before installing the switch or switches, make sure that the chosen

installation location meets the following site requirements:

•

Power

— The switch is installed near an easily accessible 100–240 VAC,

50–60 Hz outlet.

•

Clearance

— There is adequate front and rear clearance for operator

access. Allow clearance for cabling, power connections, and ventilation.

•

Cabling

— The cabling is routed to avoid sources of electrical noise such

as radio transmitters, broadcast amplifiers, power lines, and fluorescent

lighting fixtures.

•

Ambient Temperature

— The ambient switch operating temperature

range is 0 to 45ºC (32 to 113ºF) at a relative humidity of up to 95 percent,

non-condensing.

Unpacking the Switch

Package Contents

When unpacking each switch, make sure that the following items are

included:

• One PowerConnect switch

• One AC power cable (two AC power cables for the PowerConnect 7048R)

• One RJ-45 to DB-9 female cable

• One rack-mount kit for rack installation (two mounting brackets, bolts,

and cage nuts)

• One set of self-adhesive rubber pads for the free-standing switch (four pads

are included)

•

User Documentation

CD

Getting Started Guide 15

• Getting Started Guide

• Safety and Regulatory Information

• Warranty and Support Information

• Software License Agreement

Unpacking Steps

NOTE: Before unpacking the switch, inspect the container and immediately report

any evidence of damage.

1

Place the container on a clean, flat surface and cut all straps securing the

container.

2

Open the container or remove the container top.

3

Carefully remove the switch from the container and place it on a secure

and clean surface.

4

Remove all packing material.

5

Inspect the product and accessories for damage.

Mounting the Switch

WARNING: Read the safety information in the Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

The AC power connector is on the back panel of the switch.

Installing in a Rack

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

1

Place the supplied rack-mounting bracket on one side of the switch,

ensuring that the mounting holes on the switch line up to the mounting

holes in the rack-mounting bracket. Figure 1-11 illustrates where to mount

the brackets.

16 Getting Started Guide

Figure 1-11. Attaching the Brackets

2

Insert the supplied bolts into the rack-mounting holes and tighten with a

screwdriver.

3

Repeat the process for the rack-mounting bracket on the other side of the

switch.

4

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack-

mounting holes on the switch line up to the mounting holes in the rack.

5

Secure the switch to the rack with either the rack bolts or cage nuts and

cage-nut bolts with washers (depending on the kind of rack you have).

Fasten the bolts on bottom before fastening the bolts on top.

CAUTION: Make sure that the supplied rack bolts fit the pre-threaded holes in the

rack.

NOTE: Make sure that the ventilation holes are not obstructed.

Getting Started Guide 17

Installing as a Free-standing Switch

NOTE: We strongly recommend mounting the switch in a rack.

Install the switch on a flat surface if you are not installing it in a rack.

The surface must be able to support the weight of the switch and the switch

cables. The switch is supplied with four self-adhesive rubber pads.

1

Attach the self-adhesive rubber pads on each location marked on the

bottom of the switch.

2

Set the switch on a flat surface, and make sure that it has proper

ventilation by leaving 5 cm (2 inches) on each side and 13 cm (5 inches) at

the back.

Stacking Multiple Switches

You can stack PowerConnect PowerConnect 7000 Series switches up to

12 switches high, supporting up to 576 front panel ports. When multiple

switches are connected together through the stack ports, they operate as a

single unit with a larger port count. The stack operates and is managed as a

single entity.

NOTE: If you are installing a stack of switches, you need to assemble and cable the

stack before powering up and configuring it. When a stack is powered up for the

first time, the switches elect a Master Switch, which may occupy any location in

the stack. The Master LED on the front panel is illuminated on the master unit.

Creating a Switch Stack

Create a stack by connecting adjacent units using the stacking ports on the

back panel of the switch. Stacking modules are sold separately. Figure 1-12

shows the switches connected in a ring topology, which is the recommended

topology for a stack.

1

Install a separately purchased stacking module in one of the rear expansion

slots for each of the switches in the stack.

2

Connect one of the short stacking cables into either of the stacking ports

of the top switch and the switch directly below it.

If necessary, use a separately purchased, long (3 meter) stacking cable to

connect the switches.

18 Getting Started Guide

3

Repeat this process until all of the devices are connected.

4

Use the remaining stacking cable to connect the remaining free ports,

one each on the top and bottom switches.

Figure 1-12. Connecting a Stack of Switches

The stack in Figure 1-12 is connected in a ring topology and has the following

physical connections between the switches:

• The XG1 port on Unit 1 is connected to the XG2 port on Unit 2.

• The XG1 port on Unit 2 is connected to the XG4 port on Unit 3.

• The XG3 port on Unit 3 is connected to the XG2 port on Unit 1.

Stacking Standby

The stacking feature supports a Standby or backup unit that assumes the

Master unit role if the Master unit in the stack fails. As soon as a Master

failure is detected in the stack, the Standby unit initializes the control plane

and enables all other stack units with the current configuration. The Standby

unit maintains a synchronized copy of the running configuration for the

stack. During switchover, all the ports are brought down and brought up to

avoid possible loops and to get new master software applications to a

consistent state.

The Standby unit is pre-configured in the stack; however, you can use the CLI

to select a different stack member as Standby. See the User’s Configuration

Guide or the CLI Reference Guide for more information.

Unit 1

Unit 2

Unit 3

XG1 Port XG2 Port

ページを読み込んでいます...