Bitspower BPM-WTCR803 インストールガイド

[ 1 ]

instruction manual

Accessories

Bitspower CR803 Reservoir V1

1BPM-WTCR803 1 SET

4M3x45mm Screw 4 PCS

5M3x5mm Screw 4 PCS

6M4x6mm Screw 4 PCS

2Mounting bracket (short) 2 PCS

3Mounting bracket (long) 2 PCS

7BPTA-PSC-SOC 1 PCS

[ 2 ]

Installation For Mounting bracket (short)

4

2

1

step 2

step 3

step 1

5

Assemble the M3x5mm screws Install the mounting bracket (short)

Assembly steps

7

Connector direction

in connection

Select the connector with label number

J1 and color black, which will let you

operate at low speed.

Select the connector with label number

J2 and color white, which will let you

operate at full speed.

Choose the speed what you need.

[ 3 ]

Assembly steps

Dimension

[ 4 ]

Assembly steps

step 3

step 2step 1

Installation For Mounting bracket (long)

step 3

Assemble the M3x5mm screws Install the mounting bracket (long)

4

2

1

5

7

Connector direction

in connection

Select the connector with label number

J1 and color black, which will let you

operate at low speed.

Select the connector with label number

J2 and color white, which will let you

operate at full speed.

Choose the speed what you need.

[ 5 ]

Assembly steps

Dimension

[ 6 ]

step 1

Recommend For Vertical stand(Additional purchases)

step 2

step 3

Method A

[ 7 ]

step 1 step 2

step 3

Method B

[ 8 ]

Recommend For Lighting module(Additional purchases)

step 1 step 2

step 3 step 4

Dimension (After installing the lighting module)

The lighting module can be installed on surfaces in three

di󼴨erent orientations.

[ 9 ]

Dimension (After installing the lighting module and the vertical bracket)

Method A Method B

Recommend For Hole o󼴨set block(Additional purchases)

PUMP SPECIFICATION

Rated voltage：12V DC

Power consumption：15W

Maximum 󼴪ow：11±15% L/min

Noise：≤ 40dBA

PWM：Yes

MTBF：15000 hours

Warranty：2 years

Dimension: 62 x 62 x 46.7mm

Maximum lift of the water pump: 5.5±0.5m

[ 10 ]

記得上角要放對應的 LOGO!

Notice

Before filling in the water, please make sure all the components are

installed correctly. To prevent any leakage which may damage the PC

components, please perform a 24-hour leaking test with only the pump

connected to the power supply.

Bitspower reserves the right to change the product design and

interpretations. These are subject to change without notice. Product

colors and accessories are based on the actual product.

When using leak tester on water cooling loop, in order to avoid product

damage due to excessive pressure, the input pressure should not exceed

0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it

will be the fault of the customer. DO NOT use the leak teser when there is

water in the loop or the pump is running.

Bitspower recommends that customers use Bitspower Pellucid Coolant

for their coolant fluid. It is also recommended to use Bitspower Dye to

create any desired color. If the customer chooses di󼴨erent liquid coolants,

the resulting impurities may cause peeling of the coating on some of the

hardware, water channel blockage by built-up residue, improper operation

of the water pump, water tank tube breakage, and o-ring deformation

leading to leakage. Any issues related to the use of inappropriate liquid

coolants will be the responsibility of the customer.

[ 11 ]

記得上角要放對應的 LOGO!

配件

Bitspower CR803 Reservoir V1

1BPM-WTCR803 1 組

4M3x45mm 螺絲 4 支

5M3x5mm 螺絲 4 支

6M4x6mm 螺絲 4 支

使用說明書

2固定支架 2 個

3墊高支架 2 個

7BPTA-PSC-SOC 1 PCS

[ 12 ]

使用說明針對固定支架

步驟 2

步驟 3

步驟 1

組裝 M3x5mm 螺絲安裝固定支架

連接方向

選擇標籤號為 J1 且顏色為黑色的連接器，

這將使您以低速運行。

選擇標籤編號 J2 和顏色為白色的連接器，

這將使您以全速運行。

選擇所需的速度

4

2

1

5

7

[ 13 ]

組裝步驟

尺寸參考

[ 14 ]

步驟 3

步驟 2步驟 1

使用說明針對墊高支架

組裝步驟

組裝 M3x5mm 螺絲安裝墊高支架

7

連接方向

選擇標籤號為 J1 且顏色為黑色的連接器，

這將使您以低速運行。

選擇標籤編號 J2 和顏色為白色的連接器，

這將使您以全速運行。

選擇所需的速度

4

2

1

5

7

[ 15 ]

尺寸參考

組裝步驟

[ 16 ]

安裝方式 A

推薦針對垂直支架 ( 額外購買 )

步驟 1 步驟 2

步驟 3

[ 17 ]

安裝方式 B

步驟 1 步驟 2

步驟 3

[ 18 ]

推薦針對燈效模組 ( 額外購買 )

步驟 1 步驟 2

步驟 3

尺寸參考 ( 安裝燈校模組後 )

步驟 4

燈效模組有三個方向可選擇安裝

[ 19 ]

尺寸參考 ( 安裝燈效模組後裝至垂直支架 )

方法 A 方法 B

推薦滑塊 ( 額外購買 )

水泵規格

額定電壓：12V DC

功率消耗：15W

最大流量：11±15% L/min

噪音：≤ 40dBA

PWM：Yes

MTBF：≥ 15000 hours

保固：2 years

產品尺寸 : 62 x 62 x 46.7mm

水泵最大揚程：5.5±0.5m

[ 20 ]

記得上角要放對應的 LOGO!

注意

跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水

泵的情况下，進行 24 小時的跑水測試，確保無漏水情况後再開主機，避

免發生漏水而導致電腦零件的損壞。

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，

產品顏色與配件以實物為準。

當使用測氣產品測試水路時，為避免由於壓力過大導致產品損壞，輸入的

壓力請不要超過 0.5kg/cm2 (Bar)，如因壓力過大造成產品損壞，將由客戶

自行承擔，嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。

Bitspower 建議消費者使用 Bitspower 透明冷卻液。此外，也可以添加

Bitspower 染料到透明冷卻液中以滿足顏色要求。如果消費者選擇不同的

水冷液，可能會引起水路配件中的塗層剝落、積垢堵塞水道、水泵磨損、

水箱管破裂、破壞 O 型圈密封性導致漏水等。任何因使用不當水冷液導致

相關的問題將由消費者自行負責。

ページが読み込まれています...

Bitspower BPM-WTCR803 インストールガイド

Bitspower BPM-WTCR803 インストールガイド

関連論文