FMS FMM106 取扱説明書

1400mm J-3 V3

FLOAT

Optional float

RIGID

Strong durable EPO

STABLE

Smooth flying performance

Manuel d’utilisation

Instruction Manual

Bedienungsanleitung

操作手册

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product,personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure to do so

could result in injury or damage to the product or other property. This product is not intended for use by children without direct

adult supervision.

This manual contains instructions for safety operation and maintenance. It is essential to read and follow all the instructions and

warnings in the manual prior to assembly, setup or use, in order to operate and avoid damage or serious injury.

WARNING

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or

result in damage to the product or the property of others. This model is controlled by a radio signal subject to interference from

many sources outside your control. This interference can cause momentary loss of control so it is advisable to always keep a

safe distance in all directions around your model, as this margin will help avoid collisions or injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

·Never operate your model with low transmitter batteries.

·Always operate your model in an open area away from cars, traffic or people.

·Avoid operating your model in the street where injury or damage can occur.

·Never operate the model in populated areas for any reason.

·Carefully follow the directions and warnings for this and any optional support equipment you use (chargers,rechargeable

battery packs, etc.)

·Keep all chemicals, small parts and anything electrical out of the reach of children.

·Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this

purpose.

·Never lick or any place of any your model in your mouth as it could cause serious injury or even death.

Lithium Polymer (Li-Po) Battery Warning

CAUTION: Always follow the manufacturer’s instructions for safe use and disposal of batteries. Fire, property

damage, or serious injury can result from the mishandling of Li-Po batteries.

By handling, charging or using a Li-Po Battery you assume all risks associated with lithium batteries.

If at any time the batteries begin to swell or balloon, discontinue use immediately!

Always store the batteries at room temperature in a dry area to extend the life of the battery. Always transport

or temporarily store the battery in a temperature range of 40-120F. Do not store the battery or model in a car or in direct sunlight.

If stored in a hot car, the battery can be damaged or even catch fire.

Never use a Ni-Mh Charger to charge Li-Po Batteries. Failure to charge the battery with a Li-Po compatible charger

may cause fire resulting in personal injury and property damage.

Never discharge Li-Po Cells below 3V.

Never leave charging batteries unattended.

Never charge damaged batteries.

Charging the Flight Battery Warning

Use a battery charger that is designed to safely charge the Li-Po Battery. Read the charger instructions care

fully before use. When charging the battery, make certain the battery is on a heat resistant surface. It is also highly

recommended to place the Li-Po Battery inside a fire resistant charging bag readily available at hobby shops or

online.

p w

3

Before assembly, please inspect the contents of the kit. The

photo below details the contents of the kit with labels. If any

parts are missing or defective, please identify the name or

part number (refer to the spare parts list near the end of the

manual) then contact your local shop or email us: support

Kit contents

A: Fuselage

B: Main wing set

C: Horizontal stabilizer

D: Vertical stabilizer

E: Main landing gear set I: Pipe and Y cable

J:Tail strut

K:Float set

F: Supporting bar

G: Propeller set

H: Linkage rods and screws

Introduction

Kit contents

Model assembly

Battery installation

Receiver diagram

Preflight check

Clevis installation

Control horn and servo arm settings

Center of gravity(CG)

Before flying the model

Flying course

Troubleshooting

Spare parts list content

Table of contents

·····························································

·····

3

·························································3

·······················································4

············································· ········ 9

·········································

··

········ 9

··································

·····

9

····················································11

··························

·················

11

··············································· 11

··············································12

···························································12

······················································13

············································13

Introduction

The Piper J-3 Cub is an American light aircraft that was built

between 1937 and 1947 By the Piper Aircraft Company as an

affordable trainer. The aircraft has a simple, lightweight design

which gives it good low-speed handling properties and short-

field performance. During the WWII, J-3 Cub was designated as

L-4 Grasshopper, used extensively for reconnaissance,

transporting supplies, artillery spotting duties and medical

evacuation of wounded soldiers.

Like its full-sized counterpart, the all-new FMS 1400mm J-3 V3

has excellent short takeoff and landing (STOL) and slow speed

handling characteristics. FMS has dedicated significant amount

of resources in making this aircraft as detailed as possible-

components such as the engine and landing gear, among many

others, are replicated in loving detail. Something worth noting is

that FMS has made scale floats for the Cub as a response to

popular demand from the community.

To mix things up a little, FMS has selected an attractive,

historically accurate red paint scheme for the V3 Cub. Not all

J-3’s were yellow!

For pilots who are looking for an easy-to-fly, scale aircraft that

has gentle trainer characteristics, plenty of power and graceful l

ines from the golden-age of flight- the 1400mm FMS J-3 V3 is

all of that, and more.

Wingspan: 1400mm(55.1in)

Overall length: 900mm(35.4in)

Flying weight: ~ 1320g

Motor size: 3536-KV850

Wing load: 47g/dm²(0.11oz/in²)

Wing area: 28dm²(434sq.in)

ESC: 40A

Servo: 9g Servo x 4

Recommended battery: 11.1V 2200mAh 25C

Specifications

@fmsmodel.com

Features:

• Powerful 3536-850KV motor, Predator 40A ESC

• Highly detailed scale engine and landing gear

• Simple structure for quick assembly

• Durable EPO material

• Optional scale floats

A.

B.

D. I. J.

K.

E.

F.

G.

H.

C.

Landing gear set installation

Main wing set installation

4

Model assembly

1.With the fuselage bottom facing up, carefully Install the landing

gear set to the fuselage with the included screws as shown.

3.Slide the tube into the fuselage then install both wings over the

wing tube and into the wing slot of the fuselage.

Notice: The connectors on both side should be attached

precisely and firmly.

1.Have the screws go through the supporting bar and then secure on the base.

2.Lock up the fasteners of supporting bar on fuselage as shown.

PA2.6*15

KA2.0*8

PA2.6*15

Horizontal stabilizer installation

4.Secure the wings on the fuselage using the included screws

as shown.

5.Lock up the fasteners of supporting bar on main wing as

shown.

1.Secure the horizontal stabilizer using included screws as

shown.

5

Model assembly

HKM3.0*10

KA2.0*8

6

1.Slide vertical stabilizer in the rear of the fuselage.

2.Secure the vertical stabilizer using included screws as shown.

1.Make sure the servos are in the neutral position. Install the

linkage rod to elevator control horn as shown. Secure the linkage

rod in place using the included screw as shown.

2.Make sure the servos are in the neutral position. Install the l

inkage rod to rudder control horn as shown.

Note: Please refer to the control horn and servo arm settings in

page 11.

Model assembly

Linkage rod installation

Vertical stabilizer installation

KA2.0*12

KA2.0*8

1.Hook the tail struts to horizontal stabilizer and vertical

stabilizer as shown.

7

Model assembly

Tail strut installation

Antenna installation

Propeller installation

1.Insert the antenna as shown.

1.Assemble the propeller as shown.

1.Assemble the float struts to the plastic holder as shown and

secure the struts with screws.

2.Secure the float set onto the bottom of fuselage using the

included plastic parts and screws as shown.

Notice: The connectors on both side should be attached

precisely and firmly.

8

Model assembly

Float set installation

Screws 3*4

HKM3.0*10

Important ESC and model information

The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in

the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the

throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps. Several beeps with the same tune

means the ESC has detected the cells of the battery. The count of the beeps equals the cells of the battery. The motor is now

armed and will start when the throttle is moved.

The motor and ESC come pre-connected and the motor rotation should be correct. If for any reason the motor is rotating in the

wrong direction, simply reverse two of the three motor wires to change the direction of rotation.

The motor has an optional brake setting. The ESC comes with brake switched off and we recommend that the model be flown

with the brake off. However, the brake could be accidentally switched on if the motor battery is connected to the ESC while the

throttle stick is set at full throttle. To switch the brake off, move the throttle stick to full throttle and plug in the motor battery. The

motor will beep one time. Move the throttle stick to low throttle or the off position. The motor is ready to run and the brake will

be switched off.

Battery Selection and Installation. We recommend the 11.1V 2200mAh 25C Li-Po battery. If using another battery, the battery

must be at least a 11.1V 2200mAh 25C battery. Your battery should be approximately the same capacity, dimension and

weight as the 11.1V 2200mAh 25C Li-Po battery to fit the fuselage without changing the center of gravity significantly.

1.

2.

3.

4.

9

1.Pull back on the latch, releasing the canopy.

2.Remove the canopy, revealing the battery compartment.

3.Apply hook and loop tape to the battery.

4.Install a fully charged battery into the battery compartment, with

the battery cables facing aft.

Note: The center of gravity can be adjusted by moving the battery

forward or aft. Having the correct center of gravity is critical to

achieving proper flight characteristics.

Battery installation

Receiver diagram

Preflight check

The cables from the servo connector board should be connected

to your receiver in the order shown. Note that the LEDs can be

powered by any spare channel on the receiver. Tuck the wire

leads into the recessed cavity towards the rear of the battery

hatch.

Transmitter and model setup

Before getting started, bind your receiver with your transmitter.

Please refer to your transmitter manual for proper operation.

CAUTION: To prevent personal injury, DO NOT install the propel-

ler assembly onto the motor shaft while testing the control surfac-

es. DO NOT arm the ESC and do not turn on the transmitter until

the Transmitter Manual instructs you to do so.

Tips: Make sure all control sticks on your radio are in the neutral

position (rudder, elevator, ailerons) and the throttle is in the OFF

position. Make sure both ailerons move up and down (travel) the

same amount. This model tracks well when the left and right

ailerons travel the same amount in response to the control stick.

Move the controls on the transmitter to make sure the aircraft

control surface moves correctly. See diagrams right.

10

Control throws

The suggested control throw setting for the Piper J-3 Cub V3 are as follows (dual rate setting):

Tips: On the first flight, fly the model in low rate.

The first time you use high rates,be sure to fly at

low to medium speeds. High rate, as listed, is only

for EXTREME maneuvering.

Aileron

Bank left

Bank right

Elevator

Climb

Descend

Steering Rudder

Steer left

Steer right

16 12

12

14

16

18

11

More control throw

Less control throw

Horns Arms

a.

b.

c.

d.

e.

f.

Clevis installation

1.Pull the tube from the clevis to the linkage.

2.Carefully spread the clevis, then insert the clevis pin into the

desired hole in the control horn.

3.Move the tube to hold the clevis on the control horn.

Control horn and servo arm settings

The table shows the factory settings for the control horns

and servo arms. Fly the aircraft at the factory settings

before making changes.

After flying,you may choose to adjust the linkage positions

for the desired control response.

ElevatorRudderAilerons

Check the C.G. (Center of gravity)

When balancing your model, adjust the battery as necessary

so the model is level or slightly nose down. This is the correct

balance point for your model. After the first flights, the CG

position can be adjusted for your personal preference.

1. The recommended Center of Gravity (CG) location for your

model is(55-65mm) from the leading edge of the main wing

(as shown) with the battery pack installed. Mark the location of

the CG on top of the wing.

2. When balancing your model, support the plane at the marks

made on the bottom of the main wing with your fingers or a

commercially available balancing stand. This is the correct

balance point for your model. Make surethe model is assembled

and ready for flight before balancing.

55mm-65mm

Take off

Maintenance

Landing

Find a suitable flying site

Perform the range check for your plane

Monitor your flight time

Find a flying site clear of buildings, trees, power lines and

other obstructions. Until you know how much area will be

required and have mastered flying your plane in confined

spaces, choose a site which is at least the size of two to three

football fields - a flying field specifically for R/C planes is best.

Never fly near people - especially children, who can wander

unpredictably.

As a precaution, an operational ground range test should be

performed before the first flight each time you go out.

Performing a range test is a good way to detect problems

that could cause loss of control such as low batteries, defective

or damaged radio components, or radio interference. This

usually requires an assistant and should be done at the actual

flying site you will be using.

First turn on the transmitter, then install a fully-charged battery

into the fuselage. Connect the battery and install the hatch.

Remember, use care not to bump the throttle stick. Otherwise,

the propeller/fan will turn and possibly cause damage or injury.

Note: Please refer to your Transmitter Manual that came with

your radio control system to perform a ground range check. If

the controls are not working correctly or if anything seems

wrong, do not fly the model until you correct the problem. Make

certain all the servo wires are securely connected to the

receiver and the transmitter batteries have a good connection.

Monitor and limit your flight time using a timer (such as on a

wristwatch or in your transmitter if available). When the

batteries are getting low you will usually notice a performance

drop before the ESC cuts off motor power, so when the plane

starts flying slower you should land. Often (but not always)

power can be briefly restored after the motor cuts off by

holding the throttle stick all the way down for a few seconds.

To avoid an unexpected dead-stick landing on your first flight,

set your timer to a conservative 4 minutes. When your alarm

sounds you should land right away.

12

Before flying the model

Flying course

While applying power, slowly steer to keep the model straight.

The model should accelerate quickly. As the model gains flight

speed you will want to climb at a steady and even rate. It will

climb out at a nice angle of attack (AOA).

Flying

Always choose a wide-open space for flying your plane. It is

ideal for you to fly at a sanctioned flying field. If you are not

flying at an approved site always avoid flying near houses,

trees, wires and buildings. You should also be careful to avoid

flying in areas where there are many people, such as busy

parks, schoolyards, or soccer fields. Consult laws and

ordinances before choosing a location to fly your aircraft. After

takeoff, gain some altitude. Climb to a safe height before trying

technical manoeuvres, including high speed passes, inverted

flight, loops, and point rolls.

Land the model when you hear the motor pulsing (LVC) or if

you notice a reduction in power. If using a transmitter with a

timer, set the timer so you have enough flight time to make

several landing approaches.

The model’s three point landing gear allows the model to land

on hard surfaces. Align model directly into the wind and fly

down to the ground. Fly the airplane down to the ground using

1/4-1/3 throttle to keep enough energy for proper flare. Before

the model touches down, always fully decrease the throttle to

avoid damaging the propeller or other components. The key to

a great landing is to manage the power and elevator all the

way to the ground and set down lightly on the main landing

gear. After a few flights you will find the model can be set down

lightlyon the mains and you can hold the nose wheel off

balancing themodel on the mains until it slows and gently

settles the nose.

Repairs to the foam should be made with foam safe adhesives

such as hot glue, foam safe CA, and 5min epoxy. When parts

are not repairable, see the Spare Parts List for ordering by item

number.

Always check to make sure all screws on the aircraft are

tightened. Pay special attention to make sure the spinner is

firmly in place before every flight.

13

Trouble shooting

Problem Possible Cause Solution

Aircraft will not respond to

the throttlebut responds to

other controls.

-ESC is not armed.

-Throttle channel is reversed.

-Lower throttle stick and throttle trim to lowest settings.

-Reverse throttle channel on transmitter.

Extra propeller noise or

extra vibration.

-Damaged spinner, propeller,

motor or motor mount.

-Loose propeller and spinner parts.

-Propellor installed backwards.

-Replace damaged parts.

-Tighten parts for propeller adapter, propeller and spinner.

-Remove and install propeller correctly.

Reduced flight time or

aircraft underpowered.

-Flight battery charge is low.

-propeller installed backward.

-Flight battery damaged.

-Completely recharge flight battery.

-Replace flight battery and follow flight battery

instructions.

Control surface does not

move, or is slow to respond

to control inputs.

-Control surface, control horn,

linkage or servo damage.

-Wire damaged or connections

loose.

-Replace or repair damaged parts and adjust controls.

-Do a check of connections for loose wiring.

Controls reversed. Channels are reversed in the

transmitter.

Do the control direction test and adjust controls for

aircraft and transmitter.

-Motor loses power

-Motor power pulses then

motor loses power.

-Damage to motor, or battery.

-Loss of power to aircraft.

-ESC uses default soft Low Voltage

Cutoff(LVC).

-Do a check of batteries, transmitter, receiver, ESC, motor

and wiring for damage(replace as needed).

-Land aircraft immediately and recharge flight battery.

LED on receiver flashes

slowly.

Power loss to receiver. -Check connection from ESC to receiver.

-Check servos for damage.

-Check linkages for binding.

Spare parts list content

FMSRK101

FMSRK102

FMSRK103

FMSRK104

FMSRK105

FMSRK106

FMSRK107

FMSRK108

FMSRK109

FMSRK110

FMSRK111

FMSRK112

FMSPROP021

FMSDZ007

FMSDJ007

Fuselage

Main wing set

Horizontal stabilizer

Vertical stabilizer

Cowl

Linkage rod

Supporting bar set

Front landing gear set

Sticker

Propeller plate

Pipe

Screw set

Propeller

Motor shaft

Motor mount

FMSBM009

PRKV850

PRESC001

FMSSER9GPW

FMSCHR01

FMSFLT004

Motor board

Brushless motor

40A ESC

9g Servowith waterproof function)

Charger

Float Set

Visit our website: www.fmsmodel.com to see photo of this product. Enter the key word "ESC" in the search bar for the

stock ESC instruction manual.

14

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor der Inbetriebnahme mit den Funktionen

des Produkts vertraut zu machen.

Wenn das Produkt nicht ordnungsgemäß bedient wird, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen und schwere Verletzungen verursachen.

Dieses Produkt ist kein Spielzeug! Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden.

Andernfalls kann es zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses Produkt

ist nicht für den Betrieb durch Kinder ohne direkte Aufsicht von Erwachsenen vorgesehen.

Diese Anleitung enthält Hinweise zu Sicherheit und Wartung. Es ist wichtig, dass vor der Verwendung alle

Anweisungen und Warnungen in der Anleitung gelesen und befolgt werden, um Schäden oder schwere

Verletzungen zu vermeiden.

Warnhinweise

Als Benutzer dieses Produkts sind Sie allein dafür verantwortlich dieses Produkt so zu betreiben, dass weder Sie

selbst noch andere gefährdet oder Schäden am Produkt oder Eigentum anderer verursacht werden.

Dieses Modell wird von einem Funksignal gesteuert, das von vielen Quellen außerhalb Ihrer Kontrolle gestört

werden kann. Solche Störungen können zu einem vorübergehenden Kontrollverlust führen. Daher sollte immer

einen Sicherheitsabstand zu Personen und Gebäuden eingehalten werden.

Altersempfehlung: Nicht für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

· Betreiben Sie Ihr Modell niemals mit leeren Senderbatterien.

· Betreiben Sie Ihr Modell immer in einem offenen Bereich, abseits von Gebäuden, Verkehr oder Personen.

· Befolgen Sie die gesetzlichen Regelungen Ihres Landes zum Betrieb von ferngesteuerten Modellflugzeugen.

· Befolgen Sie sorgfältig die Anweisungen und Warnungen für dieses und alle unterstützenden Geräte, die Sie

verwenden (Ladegeräte, wiederaufladbare Akkus usw.).

· Bewahren Sie alle Chemikalien, Kleinteile und elektrischen Geräte außerhalb der Reichweite von Kindern auf.

· Feuchtigkeit verursacht Schäden an der Elektronik. Vermeiden Sie, dass die Produkte Wasser ausgesetzt

werden, die nicht speziell für diesen Zweck entworfen und geschützt sind.

· Nehmen Sie Teile des Produkts niemals in den Mund, da dies zu schweren Verletzungen oder sogar zum Tod

führen kann.

VORSICHT: Befolgen Sie immer die Anweisungen des Herstellers zur sicheren Verwendung und Entsorgung

von Batterien. Durch falsche Handhabung von Li-Po-Batterien können Feuer, Sachschäden oder schwere

Verletzungen verursacht werden.

Seien Sie sich über alle Risiken klar, die mit dem Umgang von Lithium Polymer (LiPo) Akkus verbunden sind.

Wenn die Akkus zu irgendeinem Zeitpunkt anschwellen oder aufblähen, verwenden Sie diese auf keinen Fall

mehr!

Um die Lebensdauer des Akkus zu verlängern sollten dieser bei Zimmertemperatur in einem trockenen Bereich

gelagert werden. Bewahren Sie den Akku oder das Modell nicht in einem Auto oder in direktem Sonnenlicht

auf. Wenn der Akku über einen längeren Zeitraum zu hohen Temperaturen ausgesetzt wird kann dieser

beschädigt werden oder sogar Feuer fangen.

Verwenden Sie niemals ein NiMh-Ladegerät, um Li-Po-Akkus aufzuladen. Wenn der Akku nicht mit einem

Li-Po-kompatiblen Ladegerät geladen wird, kann dies zu einem Brand führen, der zu Personen- und Sachschäden

führen kann.

Niemals Li-Po Zellen unter 3V entladen.

Lassen Sie Akkus beim Laden niemals unbeaufsichtigt.

Laden Sie niemals beschädigte Akkus auf.

Aufladen des LiPo-Akkus: Verwenden Sie ein Ladegerät, das die Li-Po-Batterie sicher aufladen kann. Lesen

Sie vor dem Gebrauch die Anweisungen des Ladegeräts sorgfältig durch. Achten Sie beim Laden des Akkus

darauf, dass sich der Akku auf einer hitzebeständigen Oberfläche befindet. Es wird auch dringend empfohlen,

den Li-Po Akku in einem feuerbeständigen LiPo-Koffer zu laden. LiPo Koffer finden Sie bei Ihrem Fachhändler

oder im Internet.

Sicherheitsvorkehrungen

Hinweise zu LiPo-Akkus

15

Bitte überprüfen Sie vor der Endmontage ob alle Teile des

Modells enthalten sind. Das folgende Bild zeigt den Inhalt des

Kits.

Sollten Teile fehlen notieren Sie sich bitte den Namen und die

Teilenummer (siehe Ersatzteilliste am Ende dieser

Bauanleitung) und kontaktieren Sie Ihren lokalen Händler oder

senden Sie uns eine E-Mail an [email protected].

Lieferumfang

A: Rumpf

B: Tragflächen Set

C: Höhenleitwerk

D: Seitenleitwerk

E: Fahrwerk

F: Streben

G: Propeller Set

H: Anlenkungen und Schrauben

I: Pipe und Y-Kabel

J: Heckstreben

K: Schwimmer Set

Inhaltsverzeichnis

Einleitung

Spannweite: 1400 mm(55.1in)

Gesamtlänge: 900 mm(35.4in)

Fluggewicht: ~ 1320 g

Motor: 3536-KV850

Flächenbelastung: 47g/dm²(0.11oz/in²)

Flächeninhalt:28dm²(434sq.in)

Regler: 40A

Servo: 4x 9g Servo

Empfohlener Akku: 3S 2200mAh 25C

Technische Daten

Die Piper J-3 Cub ist ein amerikanisches Leichtflugzeug, das

zwischen 1937 und 1947 von der Piper Aircraft Company als

preisgünstiger Trainer gebaut wurde. Das Flugzeug wurde so

leicht und einfach konstruiert, um auch bei niedrigen

Fluggeschwindigkeiten leicht beherrschbar zu sein. Während

des 2. Weltkrieges wurde die J-3 Cub auch als L-4 Grasshopper

bezeichnet. Sie wurde zur Aufklärung, zum Transport von

Vorräten und zur Evakuierung verwundeter Soldaten eingesetzt.

Wie auch das Vorbild verfügt die J-3 Cub V3 von FMS über

hervorragende Kurzstart und STOL (short takeoff and landing)-

Eigenschaften. FMS hat es geschafft, das Modell aus EPO

Hartschaum so detailliert wie möglich zu konstruieren. So sind

zum Beispiel der Motor und das Fahrwerk originalgetreu

nachgebaut und stehen dem Vorbild in Nichts nach. Zudem ist

ein scales Schwimmer-Set optional zum Modell erhältlich. Und

um mal ein wenig Farbe unter die Cubs zu bringen hat FMS

eine hübsche und historische rote Lackierung gewählt. Denn

nicht alle J-3 Cubs waren gelb!

Die J-3 Cub V3 ist perfekt für alle Piloten, die nach einem

absolut vorbildgetreuen und leicht zu fliegenden Flugmodell mit

tollen Trainereigenschaften und viel Kraft suchen.

Einleitung

Lieferumfang

Montage des Modells

Einsetzen des Akkus

Anschluss an den Empfänger

Flugvorbereitungen

Montage der Gabelköpfe

Ruderhorn- und Servoarmeinstellung

Schwerpunkt

Vor dem Erstflug

Fluggrundlagen

Problemlösungen

Ersatzteile

···························································15

·······················································

···

15

················································16

················································21

····································21

·································· ···· ····

···········

·····

21

································

················

·················

··

23

······································· 23

·············································24

······················································24

····································

········

······

········

········ ········

········25

········································· ········25

Merkmale:

• Kraftvoller 3536-850KV Brushless-Motor (eingebaut)

• Predator 40A Regler (eingebaut)

• Sehr detaillierter Scale Motor und Scale Fahrwerk

• kugelgelagerte Ruderhörner für höchste Präzision

(vorinstalliert)

• Robuste EPO Hartschaumkonstruktion

• Schnelle Montage

• Vorbildgetreue Schwimmer optional erhältlich

A.

B.

D. I. J.

K.

E.

F.

G.

H.

C.

Montage des Fahrwerks

Montage der Tragflächen

16

Montage des Modells

1. Drehen Sie den Rumpf um und montieren Sie das Fahrwerk

und die Abdeckung mit den beiliegenden Schrauben.

1. Befestigen Sie die langen Streben mit den entsprechenden Schrauben am Rumpf.

2. Stecken Sie die kurzen Streben wie abgebildet an den langen Streben.

3. Schieben Sie das Flächenrohr durch den Rumpf und stecken

Sie die Tragflächen auf.

Hinweis: Achten Sie darauf dass die Servostecker richtig mitein-

ander verbunden sind.

PA2.6*15

KA2.0*8

PA2.6*15

4. Befestigen Sie die Flächen wie abgebildet mit den

beiliegenden Schrauben.

1. Montieren Sie das Höhenleitwerk wie abgebildet.

5.Verriegeln Sie die Streben wie abgebildet.

17

Montage des Modells

Montage des Höhenleitwerks

HKM3.0*10

KA2.0*8

18

1. Schieben Sie das Seitenleitwerk auf den Rumpf.

2. Schrauben Sie das Seitenleitwerk wie abgebildet fest.

1. Stellen Sie sicher, dass sich die Servos in neutraler Position

befinden. Befestigen Sie die Kugelgabelköpfe und das

Anlenkungsgestänge und sichern Sie es mit den entsprechenden

Schrauben.

2. Stellen Sie sicher, dass sich die Servos in neutraler Position

befinden. Befestigen Sie die Kugelgabelköpfe wie abgebildet.

Hinweis: Beachten Sie die Ruderhorn- und Servoarm

Einstellungen auf Seite 23.

Montage des Modells

Montage des Seitenleitwerks

Montage der Anlenkungen

KA2.0*12

KA2.0*8

1. Installieren Sie die Heckstreben wie abgebildet.

1. Installieren Sie die Antenne wie abgebildet.

1. Montieren Sie den Propeller wie abgebildet.

19

Montage des Modells

Monatge der Heckstreben

Montage der Antenne

Montage des Propellers

ページを読み込んでいます...