Dell W-3600 ユーザーガイド

Dell PowerConnect

W-3000 Series Controllers

Installation Guide

Dell PowerConnect W-3000 Series Controller | Installation Guide 0510762-MU-01 | July 2010

Copyright

trademarks of Aruba Networks, Inc. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.

Originated in the USA. Any other trademarks appearing in this manual are the property of their respective companies.

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU

General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code

used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN

client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba

Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those

vendors.

Dell PowerConnect W-3000 Series Controller | Installation Guide | 3

Contents

About This Guide.......................................................................................................................................................5

Guide Overview...................................................................................................................................5

Related Documents............................................................................................................................5

Contacting Dell....................................................................................................................................5

Chapter 1 About the PowerConnect W-3000 Series Controllers....................................................7

Minimum Software Requirements...................................................................................................7

Package Checklist..............................................................................................................................7

Model Overview..................................................................................................................................8

1000Base-X (SFP) Ports.............................................................................................................8

10/100/1000Base-T Gigabit Ethernet Ports............................................................................. 9

Serial Console Port.....................................................................................................................9

Serial Console Port Adaptor.............................................................................................9

AC Power Socket......................................................................................................................10

LED Status Indicators ..............................................................................................................10

Chapter 2 Installing the W-3000 Series Controllers .......................................................................13

For a Telecom Rack:.................................................................................................................13

For a Server Rack:....................................................................................................................13

Installation in a Telecom Rack .......................................................................................................13

Installation in a Server Rack...........................................................................................................14

Tabletop Deployment.......................................................................................................................15

Initial Setup and Network Connectivity ........................................................................................15

Removal..............................................................................................................................................15

Appendix A Specifications, Safety & Compliance .............................................................................17

Physical Specifications ...................................................................................................................17

Power Management Specifications..............................................................................................17

Power Consumption.................................................................................................................17

Power Specifications (AC Input Requirements) .................................................................17

Operating Specifications.................................................................................................................17

Storage Specifications............................................................................................................18

Safety and Regulatory Compliance ...............................................................................................18

FCC Class A Device..................................................................................................................18

Proper Disposal of Dell Equipment................................................................................................18

European Union RoHS .............................................................................................................18

4 | Dell PowerConnect W-3000 Series Controller | Installation Guide

Dell PowerConnect W-3000 Series Controller | Installation Guide About This Guide | 5

About This Guide

This preface includes the following information:

z “Guide Overview” on page5

z “Related Documents” on page5

z “Contacting Dell” on page5

Guide Overview

z Chapter 1, “About the PowerConnect W-3000 Series Controllers” on page 7 provides a detailed hardware

overview of the three controllers within the W-3000 Series Controllers: the W-3200, the W-3400, and the

W-3600.

z Chapter 2, “Installing the W-3000 Series Controllers” on page 13 provides rack mounting and installation

instructions.

z Appendix A, “Specifications, Safety & Compliance” on page17 includes product technical specifications and

safety and regulatory compliance information.

Related Documents

The following documents are referred to in this guide and are considered components of the complete

documentation set needed for successful installation and management of a Dell Controller:

z

Dell PowerConnect ArubaOS Quick Start Guide

z

Dell PowerConnect ArubaOS User Guide

z

Dell PowerConnect ArubaOS 5.0 Command Line Reference

Contacting Dell

Web Site Support

Main Site www.dell.com

Support Site support.dell.com

Dell Documentation support.dell.com/manuals

6 | About This Guide Dell PowerConnect W-3000 Series Controller | Installation Guide

Dell PowerConnect W-3000 Series Controller | Installation Guide About the PowerConnect W-3000 Series Controllers | 7

Chapter 1

About the PowerConnect W-3000

Series Controllers

The PowerConnect W-3000 Series Controllers consists of three enterprise-class, wireless LAN controllers. These

controllers connect, control, and intelligently integrate wireless Access Points (APs) and Air Monitors (AMs) into

a wired LAN system.

The PowerConnect W-3000 Series Controllers consists of the following models:

z W-3200 Multi-Service Controller

The W-3200 is capable of supporting up to 32 campus connected APs..

z W-3400 Multi-Service Controller

The W-3400 is capable of supporting up to 64 campus connected APs.

z W-3600 Multi-Service Controller

The W-3600 is capable of supporting up to 128 campus connected APs.

Minimum Software Requirements

The W-3000 Series Controllers require ArubaOS 5.0.2 or later.

Package Checklist

z W-3000 Series Controllers

z AC Power Cord (country-specific)

z Rack Mount Brackets with Hardware (for rack mounting)

z Flat Serial Cable (RJ-45)

z Rubber Feet (for table top deployments)

z Serial Console Port Adaptor (RJ-45 to DB9)

z

Dell PowerConnect ArubaOS Quick Start Guide

z End User License Agreement (EULA)

z Safety, Environmental, and Regulatory Information (SERI) document

z Warranty and Support Information (WSI) document

Note: Feature related AP licenses are counted independently and in addition to the AP upgrade licenses. Contact your Dell

representative for complete details regarding software licensing options and support capacity.

Note: The master controller, its redundant master controller, and all of its local controllers must run on the same ArubaOS version.

Once you upgrade your network and install the W-3000 Series Controllers into your network, verify that the software version on

your controller matches the rest of the network. If the version shipped on the controller is prior to the version that you upgraded

your network to, you must upgrade the code on the controller to match the rest of the network.

8 | About the PowerConnect W-3000 Series Controllers Dell PowerConnect W-3000 Series Controller | Installation Guide

Model Overview

The physical hardware model overview of the W-3000 Series Controllers covers all three models within the series.

The difference between the three controller models is dependent on the licensing level purchased. The controller

model depicted in the illustrations throughout this chapter is the W-3200.

Figure 1 W-3200 Front View

1000Base-X (SFP) Ports

There are four 1000Base-X combination ports for fiber connectivity only and are intended for use with Dell SFPs

(mini-GBICs).

To purchase compatible SFP modules, contact your Dell representative for details and assistance.

Note: Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the

original packing materials. Use these materials to repack and return the unit to the supplier if needed.

Note: Optional accessories, such as SFP modules, are available for use with the W-3000 Series Controllers and are sold

separately. Contact your Dell representative for details and assistance.

Serial Console Port

10/100/1000-Base-T Gigabit

Ethernet Port

1000Base-

X (SFP) Ports

Dual-media ports (4x); 1000Base-X or

10/100/1000Base-T

Note: Ports zero through three are dual-media ports and can utilize either the 1000Base-X or 10/100/1000Base-T connections

provided. However, the 1000Base-X fiber connection has priority over the 10/100/1000Base-T copper connection. If a link is

detected for the 1000Base-X interface, the 10/100/1000Base-T connection will be disabled.

Note: Dell tests and supports Dell optics within their controller systems. Third party optics are not tested or supported; therefore,

Dell does not guarantee proper functionality of third party optics.

Dell PowerConnect W-3000 Series Controller | Installation Guide About the PowerConnect W-3000 Series Controllers | 9

10/100/1000Base-T Gigabit Ethernet Ports

There are four 10/100/1000Base-T Gigabit Ethernet (RJ-45) ports. Gigabit Ethernet uses all eight wires and each

pair is used in a bi-directional fashion, meaning the same pairs are used for both data transmission and reception.

Figure 2 illustrates the CAT-5 pin-out found on an RJ-45 connector. The CAT-5 pin-out pairs the following pins

on a 10/100/1000Base-T Gigabit Ethernet port: 1/2, 3/6, 4/5, and 7/8.

Figure 2 Gigabit Ethernet Port Pin-Out

Serial Console Port

A serial console port is provided for connection to a terminal, allowing for direct local management. The port’s

RJ-45 female connector accepts an RS-232 serial cable with a male connector.

Figure 3 Serial Console Port Pin-Out

Communication settings for the serial console port are indicated in Table 1.

Serial Console Port Adaptor

A modular adaptor can be used to convert the RJ-45 (female) connector to a DB9 (male) connector. Refer to

Figure 4 for complete details.

Table 1 Console Terminal Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

1

2

3

4

5

6

7

8

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C

Bi-directional pair -C

Bi-directional pair +D

Bi-directional pair -D

Bi-directional pair +A

Bi-directional pair -A

Bi-directional pair +B

Bi-directional pair -B

Serial

Console Port

1

2

3

4

5

6

7

8

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

GND

Caution: Do not connect an Access Point (AP) to the serial console port. The serial console port is compatible with only RS-232

devices. Non-RS-232 devices, such as APs, are not supported.

10 | About the PowerConnect W-3000 Series Controllers Dell PowerConnect W-3000 Series Controller | Installation Guide

Figure 4 RJ-45 (female) to DB9 (male) Modular Adaptor Conversion

Figure 5 represents the W-3200 rear view.

Figure 5 W-3200 Rear View

AC Power Socket

The W-3000 Series Controllers supports integrated AC powering and the AC power socket on the rear of the unit

is for use with an AC power cord (country-specific). Refer to “Power Management Specifications” on page17 for

power specification details.

LED Status Indicators

Table 2 W-3000 Series Controllers LED Status Indicators

LED Function Indicator Status

POWER Input Power Status

Indicator

On (Solid Green) Power on

Off No power

STATUS Module Status Indicator On (Solid Green) Device is operational

On (Solid Red) Device failed

On (Solid Amber) Device is loading software

Off No power

LNK 1000Base-X Ports Link Status Indicator On (Solid Green) Link has been established

Off No link on port

3

4

5

2

5

63

RJ-45 DB-9

Internal

Connections

TxD

GND

RxD

1

2

3

4

5

6

7

8

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

DB-9 Male

Pin-Out

TxD

RxD

Ground

5

4

3

2

1

9

8

7

6

Direction

Input

Output

AC Power Socket

Dell PowerConnect W-3000 Series Controller | Installation Guide About the PowerConnect W-3000 Series Controllers | 11

ACT 1000Base-X ports Activity Status Indicator On (Blinking Green) Port is transmitting or receiving

data

Off No activity

LNK/ACT 10/100/1000Base-T Ports Link/Activity Status

Indicator

On (Solid Green) Link has been established

On (Blinking Green) Port is transmitting or receiving

data

Off No link on port

1000 10/100/1000Base-T Ports Interface Speed Indicator On (Solid Green) 1000 Mbps interface speed in use

Off 10/100 Mbps interface speed in

use

Table 2 W-3000 Series Controllers LED Status Indicators

LED Function Indicator Status

12 | About the PowerConnect W-3000 Series Controllers Dell PowerConnect W-3000 Series Controller | Installation Guide

Dell PowerConnect W-3000 Series Controller | Installation Guide Installing the W-3000 Series Controllers | 13

Chapter 2

Installing the W-3000 Series

Controllers

The following tools and equipment are required for installing the Dell PowerConnect W-3000 Series Controllers:

z Rack Mount Bracket (x2, not used for tabletop installation)

z Suitable Screwdrivers

z AC Power Cord (country-specific)

For a Telecom Rack:

z 6-32 x 1/4” Phillips Head Screws (6x, included)

z 12-24 x 5/8” Phillips Head Screws (4x, included)

For a Server Rack:

z 6-32 x 1/4” Phillips Head Screws (6x, included)

z M6 x 20mm Phillips Head Screws (4x, included)

z M6 Cage Nuts (4x, inluded) or M6 Cage Clips (4x, inluded)

Installation in a Telecom Rack

To install the W-3000 Series Controllers into a 19-inch (48.26 cm) rack system:

1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 1).

2. Secure the bracket to the controller using three 6-32 x 1/4” phillips flat head screws and a suitable screwdriver.

3. Repeat these steps on the opposite side of the controller.

Warning: Before performing the following procedure, review the safety instructions that came with the controller.

14 | Installing the W-3000 Series Controllers Dell PowerConnect W-3000 Series Controller | Installation Guide

Figure 1 Rack Mount Brackets

4. Mount the controller within your organization’s rack system using four 12-24 x 5/8” phillips flat head screws

and a suitable screwdriver (see Figure 2).

Figure 2 Rack Mount Installation

5. Leave a minimum of four inches (10 cm) of space on the left and right side of the unit for proper air flow and

ventilation (see Figure 3).

6. Leave additional space in the front and back of the unit to access power cords, network cables, and LED status

indicators (see Figure 3).

Rack Mount Bracket (2x)

W-3000 Series Controllers Multi-

Service Controller

6-32 x 1/4” Phillips Flat Head Screws (6x,

3x per bracket)

Standard 19-inch

Rack System

12-24 x 5/8”

Phillips Flat Head Screws

(4x, 2x per bracket)

W-3000 Series Controllers

Multi-Service Controller with Rack

Mount Brackets

Dell PowerConnect W-3000 Series Controller | Installation Guide Installing the W-3000 Series Controllers | 15

Figure 3 Air Flow Requirements

7. Connect the AC power cord (country-specific) to the rear of the unit.

8. Plug the opposite end of the power cord into an electrical outlet to power on the controller.

Installation in a Server Rack

To install a W-3000 Series Controllers controller into a 19-inch (48.26 cm) Server rack system:

1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 1).

2. Secure the bracket to the controller using three 6-32 x 1/4” phillips head screws and a suitable screwdriver.

3. Repeat these steps on the opposite side of the controller.

4. Install the four cage nuts.

a. Begin by inserting the lower lip of the cage but over the square opeing in the back of the rail.

b. Insert the small end of the cage-nut installation tool through the opening in the rail (from the front), and

hook the tool over the top lip of the cage nut.

c. Push the cage nut in towards the rail while rotating the tool up and pulling the tool back toward you until

the top lip of the cage nut snaps into position.

5. Mount the controller within your organization’s rack system using four M6 x 20mm phillips head screws and

suitable screwdriver.

6. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and

ventilation (see Figure 3).

7. Leave additional space in front and back of the unit to access power cords, network cables, and LED status

indicators (see Figure 3).

8. Connect the AC power cord (country-specific) to the rear of the unit.

9. Plug the opposite end of the power cord into an electrical outlet to power the controller.

Keep Clear for

Air Exhaust

Keep Clear for Air Intake

Keep Open for

Easy Access

Keep Open for

Easy Access

4 inches (10

cm) Minimum

Note: The following instructions describe the installation of your controller in a rack with unthreaded, square holes. For a rack

with unthreaded, round holes, use the provided clip nuts instead.

Note: W-3000 Series Controllers do not have a power on/off switch. Power to the unit is controlled by inserting (or unplugging) the

power cord plug into your electric outlet.

16 | Installing the W-3000 Series Controllers Dell PowerConnect W-3000 Series Controller | Installation Guide

Tabletop Deployment

To deploy an W-3000 Series Controllers on a flat surface, such as a tabletop:

1. Insert the four rubber mounting feet to the bottom of the unit.

2. Attach side bezels by snapping them into place.

3. Place the unit on a hard flat surface.

Initial Setup and Network Connectivity

Once the physical installation is complete, run the initial setup on the controller to configure the IP address and

other basic system information. For complete details and instructions, refer to the ArubaOS Quick Start Guide for

the software version installed on your controller.

Removal

To remove the W-3000 Series Controllers from a 19-inch (48.26 cm) rack system:

1. Disconnect the power to the controller by unplugging the power cord from the electrical outlet.

2. Disconnect any other cables or devices attached to the controller.

3. Loosen the four rack mount screws securing the controller to your organizations rack system.

4. Remove the controller from the rack system.

Dell PowerConnect W-3000 Series Controller | Installation Guide Specifications, Safety & Compliance | 17

Appendix A

Specifications, Safety &

Compliance

Physical Specifications

z Device Dimensions (without rack mount brackets) (HxWxD):

 All Models: 1.75” x 13.8” x 11.7”

 All Models: 44 mm x 351 mm x 297 mm

Device Weight (with rack mount brackets):

z W-3200: 7.1 lbs/3.2 kgs

z W-3400/W-3600: 7.4 lbs/3.4 kgs

z Shipping Dimensions (HxWxD):

 All Models: 6.5” x 18.2” x 16.5”

 All Models: 165 mm x 462 mm x 419 mm

z Shipping Weight:

 W-3200: 9.4 lbs/4.3 kgs

 W-3400/W-3600: 9.7 lbs/4.4 kgs

Power Management Specifications

Power Consumption

z W-3200: 35 W maximum

z W-3400: 45 W maximum

z W-3600: 60 W maximum

Power Specifications (AC Input Requirements)

z W-3200:

 AC Input Voltage: 90-264 V~, Universal Input

 AC Input Current: 1.5 A

 AC Input Frequency: 47-63 Hz

z W-3400/W-3600:

 AC Input Voltage: 90-264 V~, Universal Input

 AC Input Current: 2.2 A

 AC Input Frequency: 47-63 Hz

Operating Specifications

z Operating Temperature Range: 0°C to 40°C (32°F to 104°F)

z Operating Humidity Range: 5% to 95% (RH), non-condensing

18 | Specifications, Safety & Compliance Dell PowerConnect W-3000 Series Controller | Installation Guide

Storage Specifications

z Storage Temperature Range: 0°C to 50°C (32°F to 122°F)

z Storage Humidity Range: 5% - 95% (RH), non-condensing

Safety and Regulatory Compliance

Dell provides a multi-language document containing country specific restrictions and additional safety and

regulatory information for all Dell hardware products. The Dell PowerConnect W-Series Safety, Environmental,

and Regulatory Information document is included with this product.

This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2:

2001, IEC 60825-2: 2000.

For continued compliance with the above laser safety standards, only approved Class 1 modules from our

approved vendors should be installed in Dell products.

FCC Class A Device

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CLASS 1

LASER PRODUCT

Caution: Use of controls or adjustments of performance or procedures other than those specified in this manual may result

in hazardous radiation exposure.

Dell PowerConnect W-3000 Series Controller | Installation Guide Specifications, Safety & Compliance | 19

NOM Information (Mexico Only)

The following information is provided on the device described in this document in compliance with the

requirements of the official Mexican standards (NOM):

Importer: Dell Inc. de Mexico, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 Mexico, D.F.

Model Number: 3200

z Supply Voltage: 90-264 V AC

z Frequency: 47-63 Hz

z Current consumption: 1.5 A

Model Number: 3400/3600

z Supply Voltage: 90-264 V AC

z Frequency: 47-63 Hz

z Current consumption: 2.2 A

Proper Disposal of Dell Equipment

For the most current information on Global Environmental Compliance and Dell products please see our website

at www.dell.com.

European Union RoHS

Dell products also comply with the EU Restriction of Hazardous Substances Directive

2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the

manufacture of electrical and electronic equipment. Specifically, restricted materials

under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury,

Hexavalent Chromium, and Bromine. Some Dell products are subject to the exemptions listed in RoHS Directive

Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the

“RoHS” label shown at the left indicating conformance to this Directive.

July 2010 | 0510762-MU-01 Dell PowerConnect W-3000 Series Controller | Installation Guide

ページを読み込んでいます...