Dell™ PowerEdge™ T300 Systems
Getting Started
With Your System
系统使用入门
はじめに
시스템시작하기
Dell™ PowerEdge™
T300 Systems
Getting Started
With Your System
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data
and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury,
or death.
____________________
Information in this document is subject to change without notice.
© 2007 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly
forbidden.
Trademarks used in this text: Dell, the DELL logo, PowerEdge and OpenManage are trademarks
of Dell Inc.; Intel, Celeron and Xeon are registered trademarks and Core is a trademark of Intel
Corporation; Microsoft, Windows, and Windows Server are registered trademarks of Microsoft
Corporation; Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat, Inc.;
SUSE is a registered trademark of Novell, Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks
and trade names other than its own.
Model MMU
December 2007 P/N XK766 Rev. A00
Getting Started With Your System 3
System Features
This section describes the major hardware and software features of your
system. It also provides information about other documents you may
need when setting up your system and how to obtain technical assistance.
Major hardware and software features of your system include:
• One of the following processors:
– Single-core Intel
®
Celeron
®
445 processor
– Dual-core Intel
®
Core™2 Duo E6305/E6405 processor
– Quad-core Intel
®
Xeon
®
X3323/X3353/X3363 processor
NOTE: Use the System Setup program to view processor information.
See “Using the System Setup Program” in your Hardware Owner’s Manual.
• A minimum of 512 MB single- or dual-ranked registered 667-MHz DDR2
memory modules with ECC, upgradable to a maximum of 24 GB by
installing combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory modules
in six module sockets on the system board.
• The following expansion slots:
– One PCIe x4 slot with x8 connector (if you have a DRAC card,
install it in this slot)
– One PCIe x4 slot
– Two PCIe x8 slots
– One 64-bit, 133-MHz PCI-X (3.3-V) slot
• Two integrated Gigabit Ethernet NIC ports, capable of supporting
10-Mbps, 100-Mbps, or 1000-Mbps data rates, with support for IPMI 2.0
and Wake-on-LAN.
• Seven USB 2.0-compliant connectors (two on the front, four on the back,
and one internal) capable of supporting a diskette drive, CD-ROM drive,
keyboard, mouse, or USB flash drive.
• An integrated Trusted Platform Module (TPM) version 1.2 used for
security applications, capable of generating and storing keys and storing
passwords and digital certificates. (Not available in China.)
4 Getting Started With Your System
• An integrated ATI ES1000 SVGA video controller supporting True-color
graphics in the following resolutions: 640 x 480, 800 x 600, 1024 x 768,
1280 x 1024, and 1600 x 1200.
• Systems management circuitry that monitors critical system voltages
and fan speeds. The systems management circuitry works in conjunction
with the systems management software.
• Standard baseboard management controller with serial access.
• Back-panel connectors include serial, video, four USB connectors,
and two NIC connectors.
• Two 5.25-inch drive bays for a DVD-ROM, CDRW/DVD combo,
or tape backup unit.
NOTE: DVD devices are data only.
• One 3.5-inch drive bay for floppy drive.
• Support for the following internal hard-drive configurations:
– Up to four internal, 3.5-inch, SATA hard drives with integrated drive
controllers.
– Up to four internal, 3.5-inch, Serial-Attached SCSI (SAS) hard drives
with an optional SAS controller card or backplane.
NOTE: Hot-plug capability is supported only when SATA or SAS drives are
connected to the optional SAS controller card or backplane. Either option
requires the backplane configuration.
• Optional remote access controller (DRAC 5) for remote systems
management. This option requires a dedicated PCI slot (slot #1).
• A 490-W power supply. Also available with an optional redundant 528-W
power supply.
For more information about specific features, see “Technical Specifications”.
The following software is included with your system:
• A System Setup program for quickly viewing and changing system
configuration information. For more information on this program, see
“Using the System Setup Program” in the
Hardware Owner’s Manual
.
• Enhanced security features, including a system password and a setup
password, available through the System Setup program.
Getting Started With Your System 5
• System diagnostics for evaluating system components and devices.
For information about using the system diagnostics, see “Running
the System Diagnostics” in your
Hardware Owner’s Manual
.
• Video drivers for displaying many popular application programs
in high-resolution modes.
• SATA or SAS device drivers that allow the operating system to
communicate with devices attached to the integrated SATA or SAS
subsystem. For more information about these drivers, see “Installing
Drives” in your
Hardware Owner’s Manual
.
• Systems management software and documentation CDs.
Supported Operating Systems
Your system supports the following operating systems:
• Microsoft
®
Windows Server
®
2003 R2, Standard and Enterprise Editions
(32-bit x86)
• Microsoft Windows Server 2003 R2, Standard and Enterprise x64 Editions
• Microsoft Windows Server 2003, Standard, Enterprise, and Web Editions
(32-bit x86)
• Microsoft Windows Server 2003, Standard and Enterprise x64 Editions
• Microsoft Windows Small Business Server 2003 R2, Standard and
Premium Editions (32-bit x86)
NOTE: Windows Server 2008 requires a bootable DVD drive to install the
operating system recovery media.
• Microsoft Windows Server 2008, Standard, Enterprise, and Web Editions
(32-bit x86)
• Microsoft Windows Server 2008, Standard, Enterprise, and Web x64
Editions
• Microsoft Windows Small Business Server 2008, Standard and Premium
x64 Editions
•Red Hat
®
Enterprise Linux
®
ES (version 4) (x86)
• Red Hat Enterprise Linux ES (version 4) (x86_64)
• Red Hat Enterprise Linux ES (version 5) (x86)
6 Getting Started With Your System
• Red Hat Enterprise Linux ES (version 5) (x86_64)
•SUSE
®
Linux Enterprise Server 9 (x86_64)
NOTE: SUSE
®
Linux Enterprise Server 9, prior to SP4, does not support SATA
optical devices. Installation must be performed using other methods such as
a USB CDROM.
• SUSE Linux Enterprise Server 10 (x86_64)
Other Information You May Need
CAUTION: The Product Information Guide provides important safety and
regulatory information. Warranty information may be included within this
document or as a separate document.
•The
Hardware Owner’s Manual
provides information about system
features and describes how to troubleshoot the system and install or
replace system components. The
Hardware Owner’s Manual
is available
on the CDs that came with your system or on
support.dell.com
.
• CDs included with your system provide documentation and tools
for configuring and managing your system.
• Systems management software documentation describes the features,
requirements, installation, and basic operation of the software.
• Operating system documentation describes how to install (if necessary),
configure, and use the operating system software.
• Documentation for any components you purchased separately provides
information necessary to configure and install these options.
• Updates are sometimes included with the system to describe changes
to the system, software, and/or documentation.
NOTE: Always check for updates on support.dell.com and read the updates
first because they often supersede information in other documents.
• Release notes or readme files may be included to provide last-minute
updates to the system or documentation or advanced technical reference
material intended for experienced users or technicians.
Getting Started With Your System 7
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system
does not perform as expected, see your Hardware Owner’s Manual.
Dell Enterprise Training and Certification is available; see
www.dell.com/training for more information. This service may not
be offered in all locations.
Installation and Configuration
CAUTION: Before performing the following procedure, read and follow the safety
instructions and important regulatory information in your Product Information
Guide.
This section describes the steps to set up your system for the first time.
CAUTION: Installing the feet on a stand-alone tower system is necessary to
provide a stable foundation for the system. Failure to install the feet poses the
risk of having the system tip over, possibly causing bodily injury or damage to
the system.
CAUTION: Whenever you need to lift the system, get others to assist you.
To avoid injury, do not attempt to lift the system by yourself.
Unpacking the System
Unpack your system and identify each item.
Keep all shipping materials in case you need them later.
See the documentation included with your system on installing the system
stabilizer feet.
8 Getting Started With Your System
Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable
to plug into each connector. Be sure to tighten the screws (if any) on the
monitor's cable connector.
Connecting the Power
Connect the system’s power cable(s) to the system.
Plug the other end of the cable into a grounded electrical outlet or a separate
power source such as an uninterrupted power supply (UPS) or a power
distribution unit (PDU).
Getting Started With Your System 9
Turning on the System
Turn on the system and monitor (optional).
Press the power button on the system and the monitor. The power indicators
should light.
Adjust the monitor’s controls until the displayed image is satisfactory.
Complete the 0perating System Setup
If you purchased a preinstalled operating system, see the operating system
documentation that ships with your system. To install an operating system for
the first time, see the Quick Installation Guide. Be sure the operating system
is installed before installing hardware or software not purchased with the
system.
10 Getting Started With Your System
Technical Specifications
Processor
Processor type One single-core Intel
®
Celeron
®
445
processor
or
One dual-core Intel
®
Core™2 Duo
E6305/E6405 processor
or
One quad-core Intel
®
Xeon
®
X3323/X3353/X3363 processor
Expansion Buses
Bus type PCIe, PCI-X
Expansion slots
PCIe
One x4 with x8 connector
One x4
Two x8
PCI-X One 64-bit, 133-MHz, 3.3-V
Memory
Architecture 72-bit, single- or dual-rank, registered
DDR2, 667-MHz memory modules
with ECC
Memory module sockets Six 240-pin
Memory module capacities 512 MB, 1 GB, 2 GB, or 4 GB
Minimum RAM 512 MB (one 512-MB module)
Maximum RAM 24 GB
Getting Started With Your System 11
Drives
Hard Drives
SATA Up to four internal, 1-inch-high
(3.5-inch form factor) drives connected to
integrated drive controller or RAID controller
card (non-hot plug) or SAS backplane (hot plug)
SAS Up to four internal, 1-inch-high
(3.5-inch form factor) drives connected to
optional SAS backplane (hot-plug) or SAS
controller card (non-hot plug)
NOTE: Mixing of SATA and SAS drives
is not supported
Optical drive One SATA DVD or combination CD-RW/DVD
NOTE: DVD devices are data only.
Diskette drive One optional 3.5-inch, 1.44-MB
Tape drive One optional SATA or SCSI tape backup unit
in the optical drive bay. SCSI tape drive requires
the optional PCIe SCSI controller card.
Connectors
Externally accessible
Back
NIC Two RJ-45 (from integrated Gigabit NIC)
Serial 9-pin, DTE, 16550-compatible
USB Four 4-pin, USB 2.0-compliant
Video 15-pin VGA
Front
USB Two 4-pin, USB 2.0-compliant
Internally accessible
SATA channels Six 7-pin
USB One 4-pin, USB 2.0-compliant
12 Getting Started With Your System
Video
Video type
Integrated ATI ES1000 VGA controller
Video memory
32 MB
Power
AC power supply
Wa tta ge
490 W
528 W (optional redundant power supply)
Voltage
100–240 VAC, 50/60 Hz
Current consumption
8.0–4.5 A
Heat dissipation
2275 BTU/hr maximum
Maximum inrush current Under typical line conditions and over
the entire system ambient operating range,
the inrush current may reach 55 A for 10 ms
or less or 25 A at 150 ms or less.
System battery
CR 2032 3.0-V lithium ion coin cell
Physical
Height 44.4 cm (17.4 in)
Width
21.0 cm (8.3 in)
Depth
61.2 cm (24.1 in)
Weight 19.1 kg (42 lb)
Getting Started With Your System 13
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see www.dell.com/environmental_datasheets.
Temperature
Operating 10° to 35°C (50° to 95°F)
Storage –40° to 65°C (–40° to 149°F)
Relative humidity
Operating 20% to 80% (noncondensing)
Storage 5% to 95% (noncondensing)
Maximum vibration
Operating 0.26 G (half-sine wave) at a sweep
of 3 to 200 MHz for 15 minutes
Storage 0.5 G at 3–200 Hz for 15 min
Maximum shock
Operating Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system)
of 36 G for up to 2.6 ms
Storage Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system)
of 71 G for up to 2 ms
Altitude
Operating –16 to 3,048 m (–50 to 10,000 ft)
Storage –16 to 10,668 m (–50 to 35,000 ft)
Airborne Contaminant Level
Class G2 or lower as defined by ISA-S71.04-1985
14 Getting Started With Your System
Dell
™
PowerEdge
™
T300
系统
系统使用入门
注、注意和警告
注： “注”表示可以帮助您更好地使用计算机的重要信息。
注意：“注意”表示可能会损坏硬件或导致数据丢失、并告诉您如
何避免此类问题。
警告：“警告”表示可能会导致财产损失、人身伤害甚至死亡。
____________________
本说明文件中的信息如有更改、恕不另行通知。
© 2007 Dell Inc.
版权所有、翻印必究。
未经
Dell Inc.
书面许可、严禁以任何形式进行复制。
本文中使用的商标：
Dell
、
DELL
徽标、
PowerEdge
和
OpenManage
是
Dell Inc.
的商标；
Intel
、
Celeron
和
Xeon
是
Intel Corporation
的注册商标而
Core
是
Intel Corporation
的商标；
Microsoft
、
Windows
和
Windows Server
是
Microsoft Corporation
的注册商标；
Red Hat
和
Red Hat Enterprise Linux
是
Red Hat, Inc.
的注册商标；
SUSE
是
Novell, Inc.
的注册商标。
本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的
产品。
Dell Inc.
对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。
型号
MMU
2007
年
12
月
P/N XK766 Rev. A00
系统使用入门 17
系统功能
本节介绍系统的主要硬件和软件功能。还介绍了有关在安装系统时
可能需要的其它说明文件的信息、以及如何获得技术帮助的信息。
系统的主要硬件和软件功能包括：
•
以下处理器之一：
–
单核
Intel
®
Celeron
®
445
处理器
–
双核
Intel
®
Core
™
2 Duo E6305/E6405
处理器
–
四核
Intel
®
Xeon
®
X3323/X3353/X3363
处理器
注：使用系统设置程序可以查看处理器信息。请参阅《硬件用
户手册》中的“使用系统设置程序”。
•
至少
512 MB
（单排或双排）
667 MHz
带寄存器的
DDR2
内存模块
（带
ECC
）、通过在系统板上的六个模块插槽中安装
512 MB
、
1 GB
、
2GB
或
4 GB
内存模块、最多可升级至
24 GB
。
•
以下扩充槽：
–
一个带
x8
连接器的
PCIe x4
插槽 （如果有
DRAC
卡，将其安装
在此插槽中）
–
一个
PCIe x4
插槽
–
两个
PCIe x8
扩充槽
–
一个
64
位、
133-MHz PCI-X (3.3-V)
插槽
•
两个集成千兆位以太网
NIC
端口、能够支持
10 Mbps
、
100 Mbps
或
1000-Mbps
数据速率、同时支持
IPMI 2.0
和通过
LAN
唤醒。
•
七个
USB 2.0
兼容连接器（两个位于正面、四个位于背面以及一个位于
内部）、能够支持软盘驱动器、
CD-ROM
驱动器、键盘、鼠标或
USB
快
擦写驱动器。
•
集成的受信任的平台模块
(TPM) 1.2
版、用于安全保护应用程序、能够
生成并存储密钥以及存储密码和数字证书（在中国未提供此功能）。
•
集成的
ATI ES1000 SVGA
视频控制器、支持以下分辨率的真彩色图形：
640 x 480
、
800 x 600
、
1024 x 768
、
1280 x 1024
和
1600 x 1200
。
•
系统管理电路、用于监测系统临界电压和风扇速率。系统管理电路、
需要与系统管理软件配合工作。
18 系统使用入门
•
标准底板管理控制器、支持串行访问。
•
背面板连接器、包括串行连接器、视频连接器、四个
USB
连接器和两个
NIC
连接器。
•
两个
5.25
英寸驱动器托架、用于
DVD-ROM
、
CDRW/DVD
组合或磁带
备份装置。
注：
DVD
设备仅用于数据。
•
一个
3.5
英寸驱动器托架、用于软盘驱动器。
•
支持以下内部硬盘驱动器配置：
–
最多四个带有集成驱动器控制器的内部
3.5
英寸
SATA
硬盘驱动器。
–
最多四个带有可选
SAS
控制器卡或背板的内部
3.5
英寸串行连接的
SCSI (SAS)
硬盘驱动器。
注：仅当
SATA
或
SAS
驱动器连接到
SAS
控制器卡或背板时支持热插
拔功能。以上两个选项均要求背板配置。
•
可选的远程访问控制器
(DRAC 5)
、用于远程系统管理。此选项要求专
用的
PCI
插槽（插槽编号
1
）。
•
490 W
电源设备。还提供可选的
528 W
冗余电源设备。
有关特定功能部件的详情、请参阅“技术规格”。
您的系统附带以下软件：
•
系统设置程序、用于快速查看和更改系统配置信息。有关此程序的
详情、请参阅《硬件用户手册》中的“使用系统设置程序”。
•
增强的安全保护功能、包括系统密码和设置密码、可通过系统设置
程序进行设置。
•
系统诊断程序、用于评估系统组件和设备。有关使用系统诊断程序
的信息、请参阅《硬件用户手册》中的“运行系统诊断程序”。
•
视频驱动程序、用于以高分辨率模式显示多种常见应用程序。
•
SATA
或
SAS
设备驱动程序、允许操作系统与连接至集成
SATA
或
SAS
子系统的设备进行通信。有关这些驱动程序的详情、请参阅
《硬件用户手册》中的“安装驱动器”。
•
系统管理软件和说明文件
CD
。
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/