Dell PowerEdge 850 ユーザーガイド

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del rack

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own

June 2005 P/N W8622 Rev. A00

Contents 3

Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems

. . . . . . . . . . . . . . . . . . . . . 5

Installation Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Important Safety Information

. . . . . . . . . . . . . . . . . . . . . . . . . 6

Rack Requirements for VersaRails

. . . . . . . . . . . . . . . . . . . . . . 6

Four-Post Rack Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rack Stabilizer Feet

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies

. . . . . . . . . . . . . . . . . . . . . . 7

RapidRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . 8

VersaRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation Tasks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Removing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . . . . 10

Marking the Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installing the Mounting Rails in the Rack

. . . . . . . . . . . . . . . . . . 12

Installing and Removing Chassis Static Rail Modules

. . . . . . . . . . . 14

Installing the System in the Rack

. . . . . . . . . . . . . . . . . . . . . . 15

Installing the Releasable Tie Wraps

. . . . . . . . . . . . . . . . . . . . 17

Removing the System From the Rack

. . . . . . . . . . . . . . . . . . . . 18

Replacing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . . . . 18

Two-Post Rack Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Recommended Tools and Supplies

. . . . . . . . . . . . . . . . . . . . . 19

Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation Tasks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Marking the Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installing the Mounting Rails

. . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the System in the Rack

. . . . . . . . . . . . . . . . . . . . . . 26

Installing the Releasable Tie Wraps

. . . . . . . . . . . . . . . . . . . . 26

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4 Contents

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . . . . . 8

Figure 1-2. VersaRails Rack Kit Contents

. . . . . . . . . . . . . 9

Figure 1-3. One Rack Unit

. . . . . . . . . . . . . . . . . . . . . 10

Figure 1-4. Marking the Vertical Rails

. . . . . . . . . . . . . . 11

Figure 1-5. Installing the RapidRails Mounting Rails

. . . . . . . 13

Figure 1-6. Installing the VersaRails Mounting Rails

. . . . . . . 14

Figure 1-7. Installing and Removing Static Rail Modules

. . . . 15

Figure 1-8. Installing the System in the Rack

. . . . . . . . . . . 16

Figure 1-9. Installing the Releasable Tie Wraps

. . . . . . . . . 17

Figure 1-10. Two-Post Rack Kit Components

. . . . . . . . . . . 19

Figure 1-11. Two-Post, Open-Frame Relay Rack Universal-Hole

Spacing

. . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 1-12. Two-Post, Open-Frame Relay Rack Wide-Hole

Spacing

. . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 1-13. Installing the Mounting Rails for Center-Mount

Configuration

. . . . . . . . . . . . . . . . . . . . . 23

Figure 1-14. Configuring the Adjustable Mounting Bracket

for Flush-Mount Installation

. . . . . . . . . . . . . 24

Figure 1-15. Installing the Mounting Rails for Flush-Mount

Configuration

. . . . . . . . . . . . . . . . . . . . . 25

Rack Installation Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your

system and working environment from potential damage. For complete safety information,

see the

Product Information

Guide

.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well

as to various peripherals or supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks

or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before

installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under

certain circumstances. Therefore, always install the stabilizer(s) before installing components in the

rack.

CAUTION: After installing components in a rack, never pull more than one component out of the rack

on its slide assemblies at one time. The weight of more than one extended component could cause the

rack to tip over and injure someone.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a rack

cabinet using the customer rack kit when both the rack cabinet and rack kit were designed for your

system. The installation of your system and rack kit in any other rack cabinet has not been approved

by any safety agencies. It is your responsibility to have the final combination of system and rack kit in a

cabinet evaluated for suitability by a certified safety agency. The manufacturer disclaims all warranties

and liability in connection with such combinations.

• System rack kits are intended to be installed in an approved rack by trained service

technicians. If you install the kit in any other rack, be sure that the rack meets the

specifications.

• Before working on the rack, make sure that the stabilizers are secured to the rack, and that

the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack

or front stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the rack.

• Do not overload the AC power supply branch circuit that provides power to the rack.

The total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any system/component when servicing other systems/components

in a rack.

6 Rack Installation Guide

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more

systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can be installed

in all the system manufacturer's rack cabinets without tools, and the VersaRails™ rack kit can be

installed in most industry-standard rack cabinets. The procedures for installing both RapidRails

and VersaRails rack kits are similar. One rack kit is required for each system to be installed in the

rack cabinet.

This guide includes procedures for the following rack kits:

• RapidRails kit in a four-post rack cabinet

• VersaRails kit in a four-post rack cabinet

• Two-post kit (installed in either center-mount or flush-mount configuration)

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions," found

earlier in this guide, as well as the safety instructions found in your

Product Information Guide

for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current

system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on their casters. They do not have

brakes. Use extreme caution while moving the rack cabinet. Retract the leveling feet when relocating

the rack cabinet. Avoid long or steep inclines or ramps where loss of cabinet control may occur. Extend

the leveling feet for support and to prevent the cabinet from rolling.

NOTE: For instructions on installing the system itself, see "Installing the System in the Rack."

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as

others who may be involved. Your system may be very large and heavy and proper preparation and

planning are important to prevent injury to yourself and to others. This precaution becomes

increasingly important when systems are installed high up in the rack.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for

your system. Using the rack kit for another system may result in damage to the system and personal

injury to yourself and to others.

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack

that meets the specifications of American National Standards Institute (ANSI)/Electronic Industries

Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that is installed in a rack.

Rack Installation Guide 7

Four-Post Rack Installation

Before attempting this installation, read through this entire procedure carefully.

Rack Stabilizer Feet

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks

or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before

installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under

certain circumstances. Therefore, always install the stabilizer(s) before installing components in

the rack.

The stabilizer feet help prevent the rack from tipping over. See the documentation provided

with the rack cabinet for instructions on installing and anchoring the stabilizer feet.

Recommended Tools and Supplies

You may need the following items to install the system in a four-post rack cabinet:

• #2 Phillips screwdriver

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

8 Rack Installation Guide

RapidRails Rack Kit Contents

• One pair of RapidRails mounting rails

• Releasable tie wraps (2) (not shown in Figure 1-1)

Figure 1-1. RapidRails Rack Kit Contents

VersaRails Rack Kit Contents

• One pair of VersaRails mounting rails

• 10-32 x 0.5-inch flange-head Phillips screws (8)

• Releasable tie wraps (2) (not shown in Figure 1-2)

NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and

number of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified

as a 10-32 screw.

mounting rails (2)

releasable tie wrap

attachment points (2)

Rack Installation Guide 9

Figure 1-2. VersaRails Rack Kit Contents

Installation Tasks

Installing a rack kit involves performing the following tasks (described in detail in subsequent

sections) in their numbered order:

1

Removing the rack doors

2

Marking the rack

3

Installing the mounting rails in the rack

• RapidRails installation

• VersaRails installation

• Static Rails Installation

4

Installing the system in the rack

5

Routing cables and securing with releasable tie wraps

6

Replacing the rack doors

NOTE: Three procedures are provided for task 3. These procedures are for the RapidRails kit,

the VersaRails kit, and the Static Rail kit.

10-32 x 0.5-inch flange-

head Phillips screws (8)

mounting rails (2)

releasable tie wrap

attachment points (2)

10 Rack Installation Guide

Removing the Rack Doors

See the procedures for removing doors in the documentation provided with your rack cabinet.

CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install

them by yourself.

CAUTION: Store the doors where they will not injure someone if the doors accidently fall over.

Marking the Rack

For a 1-U system, you must allow 1 U (44 mm, or 1.75 inches) of vertical space for each system

you install in the rack.

Rack cabinets that meet EIA-310 standards have an alternating pattern of three holes per rack unit

with center-to-center hole spacing (beginning at the top hole of a 1-U space) of 15.9 mm, 15.9 mm,

and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the front and back vertical rails

(see Figure 1-3). Rack cabinets may have round or square holes.

NOTE: The vertical rails may be marked by horizontal lines and numbers in 1-U increments. If you want,

you can make a note of the number marking on the rack’s vertical rail. It is not necessary to mark or place

tape on the rack.

Figure 1-3. One Rack Unit

CAUTION: If you are installing more than one system, install the mounting rails so that the first system

is installed in the lowest available position in the rack.

1 U (44 mm or 1.75 inches)

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

Rack Installation Guide 11

To mark the rack, perform the following steps:

1

Place a mark (or tape) on the rack's front vertical rails where you want to locate the bottom

of the system you are installing in the rack.

The bottom of each 1-U space is at the middle of the narrowest metal area between holes

(marked with a horizontal line on some rack cabinets—see Figure 1-4).

2

Place a mark 44 mm (1.75 inches) above the original mark you made (or count up three holes

in a rack that meets EIA-310 standards) and mark the rack's front vertical rails with a felt-

tipped pen or masking tape (if you counted holes, place a mark just above the top hole). This

mark or piece of tape indicates where the system's upper edge will be located on the vertical

rails (see Figure 1-4).

Figure 1-4. Marking the Vertical Rails

tape on vertical rail

12 Rack Installation Guide

Installing the Mounting Rails in the Rack

Installing the RapidRails Mounting Rails

1

At the front of the rack cabinet, position one of the RapidRails mounting rails so that its

mounting-bracket flange fits between the marks or tape you placed (or numbered location)

on the vertical rails (see Figure 1-5).

The top mounting hook on the front mounting-bracket flange should enter the top hole

between the marks you made on the vertical rails.

2

Push the mounting rail forward until the mounting hooks enter their square holes, and then

push down on the mounting-bracket flange until the mounting hooks seat and the push

button pops out and clicks (see Figure 1-5).

3

At the back of the cabinet, pull back on the mounting-bracket flange until the mounting

hooks enter their square holes, and then push down on the flange until the mounting hooks

seat and the push button pops out and clicks.

4

Repeat step 1 through step 3 for the mounting rail on the other side of the rack.

5

Ensure that the mounting rails are mounted at the same vertical position on both sides

of the rack.

Rack Installation Guide 13

Figure 1-5. Installing the RapidRails Mounting Rails

Installing the VersaRails Mounting Rails

1

At the front of the rack cabinet, position one of the VersaRails mounting rails so that its

mounting-bracket flange fits between the marks (or numbered location) on the vertical rails

(see Figure 1-6).

The three holes on the front of the mounting-bracket flange should align with the holes

between the marks you made on the front vertical rail.

2

Install two 10-32 x 0.5-inch flange-head Phillips screws in the mounting-bracket flange's

top- and bottom-holes to secure the mounting rail to the front vertical rail.

3

At the back of the cabinet, pull back on the mounting-bracket flange until the mounting

holes align with their respective holes on the back vertical rail.

4

Install two 10-32 x 0.5-inch flange-head Phillips screws in the back mounting-bracket flange's

top- and bottom-holes to secure the mounting rail to the back vertical rail.

5

Repeat step 1 through step 4 for the mounting rail on the other side of the rack.

6

Ensure that the mounting rails are mounted at the same position on the vertical rails on

each side of the rack.

front of rack

mounting rails (2)

mounting hooks (2)

push button

14 Rack Installation Guide

Figure 1-6. Installing the VersaRails Mounting Rails

Installing and Removing Chassis Static Rail Modules

NOTE: You do not need to remove the optional front bezel to install or remove the chassis static rail

modules from the chassis.

1

To install the rails, locate the J slots on both rails. Locate the two corresponding shoulder

screws that are on both sides of the chassis toward the front and midpoint (see Figure 1-7).

2

To attach the rails to the chassis, align the two J slots on the rail modules with the shoulder

screws. Position each rail directly below the two corresponding shoulder screws

(see Figure 1-7).

3

To seat the rails, pull up on the front latches attached to the front of each rail. Pull up

and back on each rail, snapping them into place on the chassis.

4

To remove the rails from the chassis, pull up on the front latches to release each rail.

5

Unseat the rails from the J slots and remove the rails from the chassis.

front of rack

rails modules (2)

10-32 x 0.5-inch

flange-head Phillips

screws (4 per

mounting rail)

mounting-bracket flange

Rack Installation Guide 15

Figure 1-7. Installing and Removing Static Rail Modules

Installing the System in the Rack

CAUTION: If you are installing more than one system, install the first system in the lowest

available position in the rack.

CAUTION: Because of the size and weight of the system, never attempt to install the system in

the mounting rails by yourself.

To install the system on the rack, perform the following procedure:

1

From the front of the system, lift the chassis into position so that the side rails are aligned

with the mounting rails on the rack.

rail modules (2)

shoulder screws (4)

front release latch

J slots (4)

16 Rack Installation Guide

Figure 1-8. Installing the System in the Rack

2

Working from right to left, position the chassis on the mounting rails and slide back

(see Figure 1-8).

3

Push the chassis back into the mounting rails until the system stops (see Figure 1-8).

4

Secure both thumbscrews on the front panel of the chassis.

NOTE: Figure 1-8 applies to the RapidRails, VersaRails, and two-post rack kits.

mounting rails (2)

system rails (2)

thumbscrews (2)

back release latches (2)

Rack Installation Guide 17

Installing the Releasable Tie Wraps

The two releasable tie wraps are used to secure your system’s cables to the mounting rails.

1

Locate the releasable tie wrap attachment points located on the two back mounting-bracket

flanges (see Figure 1-9).

Figure 1-9. Installing the Releasable Tie Wraps

2

Push the tie wrap’s fastener through the attachment point.

3

Push the tie wrap’s plunger until it snaps to secure the tie wrap to the mounting rail.

4

Using the releasable tie wrap, secure your system’s cables to the mounting rail.

mounting rails (2)

releasable tie wraps (2)

18 Rack Installation Guide

Removing the System From the Rack

To remove the system from the rack, perform the following procedure:

NOTE: You do not need to remove the optional front bezel to install or remove the system from the rack.

1

Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

2

Disengage the both thumbscrews on the front panel of the chassis.

3

On either side of the system, locate the back release latches.

4

Pull the system out of the rack until it stops, and then push down on both release levers

to actuate the side-rail safety catches (see Figure 1-8).

5

Pull the system completely out of the rack.

Replacing the Rack Doors

See the procedures for replacing doors in the documentation provided with your rack.

CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install

them by yourself.

This completes the rack installation of your system in a four-post rack cabinet.

Two-Post Rack Installation

The two-post rack kit is used to install a system in a two-post, open-frame relay rack, such as those

found in telecommunications equipment facilities. Both 7.62-cm or 15.24-cm (3-inch and 6-inch)

wide two-post racks with universal hole spacing or wide hole spacing are accommodated. You can

install this kit in a center-mount or a flush-mount configuration.

You must properly secure the two-post relay rack to the floor, the ceiling or upper wall, and where

applicable, to adjacent racks, using floor and wall fasteners and bracing specified or approved by

the rack manufacturer or by industry standards. See the two-post rack manufacturer's

documentation for warnings before attempting this installation.

CAUTION: Do not attempt to install the system into a two-post, open-frame relay rack that has not been

securely anchored in place. Damage to the system and personal injury to yourself and to others may

result.

See "Safety Instructions" for additional safety information regarding rack installation.

ページが読み込まれています...

Dell PowerEdge 850 ユーザーガイド

Dell PowerEdge 850 ユーザーガイド

他の言語で

関連論文