HQ460
ENGLISH 4
简体中文 13
4
Important
Read these instructions for use carefully before using
the appliance and save them for future reference.
The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages ranging from 100 to 240 volts.
Charge, store and use the appliance at a
temperature between 5 cC and 35 cC.
Do not recharge the shaver in a closed pouch.
Keep the appliance dry.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and in accordance with the instructions in
this instruction manual, the appliance is safe to use
according to scientic evidence available today.
Charging
Make sure the appliance is switched off before you
start charging it.
When you charge the shaver for the rst time
or after a long period of disuse, let it charge
continuously for 12 hours. Charging normally takes
approx. 8 hours.
,
,
,
,
,
,
ENGLISH
Do not leave the appliance connected to the mains
for more than 24 hours.
Charging the appliance
Charge the appliance when the motor stops or
starts running slower.
Do not recharge the shaver in a closed pouch.
1 Push the slide pins out of the appliance by
means of the slide.
2 Insert the slide pins into the wall socket.
As soon as you start charging the empty shaver,
the green pilot light goes on.
3 Remove the appliance from the wall socket
when the battery has been fully charged.
Shaving time
A fully charged shaver has a shaving time of up to
30 minutes.
,
CHARGECHARGE
ENGLISH 5
Using the appliance
Shaving
1 Switch the appliance on by pressing the switch
lock (1) and pushing the on/off slide upwards
(2).
Note: The switch lock prevents accidental switching on
of the appliance.
2 Move the shaving heads quickly over your skin,
making both straight and circular movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get accustomed
to the Philips shaving system.
3 Switch the shaver off by pushing the on/off
slide downwards.
4 Put the protection cap on the shaver every
time you have used it, to prevent damage.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
For easy and optimal cleaning, the Philips Action
Clean (shaving head cleaner, type HQ100) is
available. Ask your Philips dealer for information.
Note: The Philips Action Clean may not be available in
all countries. Contact the Customer Care Centre in your
country about the availability of this accessory.
You can also clean the shaver in the following way:
,
ENGLISH6
Every week: shaving unit and hair chamber
1 Switch the shaver off.
2 Cleanthetopoftheappliancerst,usingthe
brush supplied.
3 Press the release button (1) and remove the
shaving unit (2).
4 Clean the inside of the shaving unit and the
hair chamber with the brush.
5 Put the shaving unit back onto the shaver.
Every two months: shaving heads
1 Switch the shaver off.
2 Press the release button (1) and remove the
shaving unit (2).
ENGLISH 7
3 Remove the retaining frame by pushing the
sides of the central spring towards each other
(1) and lifting the retaining frame out of the
shaving unit (2).
4 Slide the shaving heads out of the retaining
frame and clean them one by one.
Do not mix up the cutters and the guards.
This is essential since each cutter has been
ground with its corresponding guard for optimal
performance. If you accidentally mix the sets up, it
could take several weeks before optimal shaving
performance is restored.
5 Clean the cutter with the short-bristled side of
the brush.
Brush carefully in the direction of the arrow.
6 Brush the guard.
7 Slide the shaving heads back into the retaining
frame and put the retaining frame back into the
shaving unit.
8 Put the shaving unit back onto the shaver.
For extra thorough cleaning, clean the shaving heads
by putting them in a degreasing liquid (e.g. alcohol)
every six months. To remove the shaving heads,
follow steps 1 to 4 described above. After cleaning,
lubricate the central point on the inside of the
ENGLISH8
guards with a drop of sewing machine oil to prevent
wear of the shaving heads.
Storage
Put the protection cap on the shaver to prevent
damage.
The appliance can be stored in the pouch
supplied.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with
HQ4+ Philips shaving heads only.
1 Switch the shaver off.
2 Press the release button (1) and remove the
shaving unit (2).
3 Remove the retaining frame by pushing the
sides of the central spring towards each other
(1) and lifting the retaining frame out of the
shaving unit (2).
4 Slide the shaving heads out of the retaining
frame.
,
,
ENGLISH 9
5 Slide new shaving heads into the retaining
frame.
6 Put the retaining frame back into the shaving
unit.
7 Put the shaving unit back onto the shaver.
Accessories
The following accessories are available:
HQ4 + Philips shaving heads.
HQ100 Philips Shaving Head Cleaner (not
available in China).
HQ101 Philips Shaving Head Cleaning Fluid (not
available in China).
HQ110 Philips Shaving Head Cleaning Spray (not
available in China).
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand
it in at an ofcial collection point for recycling. By
doing this, you help to preserve the environment.
Batteries contain substances that may pollute the
environment. Always remove the batteries before
discarding the appliance or handing it in at an
ofcial collection point. Dispose of the batteries at
an ofcial collection point for batteries.
-
-
-
-
-
-
ENGLISH10
Disposal of the battery
Only remove the battery if it is completely empty.
1 Remove the shaver from the wall socket.
2 Let the shaver run until it stops, undo the
screws and open the shaver.
3 Remove the battery.
Do not connect the shaver to the mains again after
the battery has been removed.
Guarantee & service
If you need information or if you have a problem,
please visit the Philips website at www.philips.com
or contact the Philips Customer Care Centre
in your country (you nd its phone number in
the worldwide guarantee leaet). If there is no
Customer Care Centre in your country, go to
your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and
Personal Care BV.
The shaving heads (cutters and guards) are not
covered by the terms of the international guarantee
because they are subject to wear.
Troubleshooting
1
Reduced shaving performance
ENGLISH 11
Cause 1: The shaving heads are dirty. The shaver
has not been cleaned well enough or has not
been cleaned for a long time.
Clean the shaver thoroughly before you continue
shaving. See chapter ‘Cleaning and maintenance’.
Cause 2: long hairs are obstructing the shaving
heads.
Clean the cutters and guards with the brush
supplied. See chapter ‘Cleaning and maintenance’,
section ‘Every two months: shaving heads’.
Cause 3: the shaving heads are damaged or worn.
Replace the shaving heads. See chapter
‘Replacement’.
2 The shaver does not work when the on/off
slide is pushed upwards.
Cause: the battery is empty.
Recharge the battery. See chapter ‘Charging’.
-
-
-
-
ENGLISH12
13
注意事项
使用本产品前，请仔细阅读本使用
说明书，并妥善保管以备日后参
考。
本产品配有一个自动电压选择
器，适合 100 至 240 伏范围内的
电源电压。
产品充电、存放和使用的温度范
围在 5 cC 到 35 cC 之间。
不要将剃须刀放在软袋里充电。
保持产品干燥。
本产品不打算由肢体不健全、感
觉或精神上有障碍或缺乏相关
经验和知识的人（包括儿童）使
用，除非有负责他们安全的人对
他们使用本产品进行监督或指
导。
应照看好儿童，确保他们不玩耍
这些产品。
电磁场 (EMF)
这款飞利浦产品符合关于电磁场
(EMF) 的相关标准。据目前的科学
证明，如果正确使用并按照本手册
中的说明进行操作，本产品是安全
的。
,
,
,
,
,
,
简体中文
14
充电
开始充电之前，确保产品电源已关闭。
如果是第一次充电，或长时间未使用之后的第
一次充电，应将其连续充 12 小时。充电通常需
约 8 小时。
不要将本产品与电源接通超过 24
小时。
为产品充电
当马达停转或转速开始下降时，为产品充电。
不要将剃须刀放在软袋里充电。
1 滑动滑块，以将活动插头推出产品。
2 将活动插头插入插座中。
只要开始为电量耗尽的剃须刀充电，绿色显
示灯就会亮起。
3 请在电池完全充电后，从插座上取下产品。
,
CHARGECHARGE
简体中文14
1515
剃须时间
完全充电的剃须刀可最长使用达 30 分钟。
使用本产品
剃毛
1 按下开关锁 (1)，向上推开/关滑块 (2)，将
产品通电。
注： 开关锁可防止无意中打开产品电源。
2 将剃须刀头在皮肤上快速移动，作直线和迂
回动作。
在干爽的面部剃须效果最佳。
您的皮肤可能需要 2 到 3 周才能适应飞利浦剃
须系统。
3 向下推开/关滑块，关闭剃须刀。
4 每次使用后，盖上剃须刀保护盖，以防受
损。
清洁和维护
为保证更好的剃须效果，剃须刀必须定期清
洗。
为了更方便有效地清洁剃须刀，特推出飞利
浦剃须刀头清洁器（型号HQ100）。有关信
息，请咨询飞利浦家庭小电器客户服务部。
,
简体中文
16
注： 飞利浦剃须刀头清洁器不是所有国家/地区
都有销售。请向当地的客户服务中心了解是否
有售。
您也可以用下列方式清洁剃须刀：
每周：剃须刀头部件和胡茬储藏室
1 关闭剃须刀。
2 使用产品随附的毛刷首先清洁产品顶部。
3 按下释放钮 (1)，取下剃须刀头部件 (2)。
4 使用毛刷清洁剃须刀头部件内侧和胡茬储藏
室。
5 将剃须刀头部件重新安装到剃须刀上。
简体中文16
17简体中文 17
每两个月：剃须刀头
1 关闭剃须刀。
2 按下释放钮 (1)，取下剃须刀头部件 (2)。
3 向中间捏中央弹簧的两侧 (1)，并向上提起
取出固定架，将其从剃须刀头部件中取出
(2)。
4 将剃须刀头滑出固定架，并一个一个地清
洁。
不要将刀片和网罩混合在一起。
这一点很重要，因为每组刀片和网罩都已相互
磨合得很好，以便获得最佳剃须效果。如果不
小心将它们弄混，剃须刀将需要数周时间才能
恢复到最佳剃须性能。
5 用毛刷的短毛一侧清洁刀片。
按箭头方向仔细刷净。
6 刷净网罩。
18
7 滑动剃须刀头，将其重新安装到固定架上，
然后将固定架重新安装到剃须刀头部件上。
8 将剃须刀头部件重新安装到剃须刀上。
如需彻底清洁，则需每六个月将剃须刀头浸入
脱脂液（如酒精）清洗。按照上述步骤 1 至 4
取下剃须刀头。清洗完成后，向网罩内的中心
点滴入一滴缝纫机油，以防剃须刀头磨损。
存放
盖上剃须刀保护盖，以防受损。
本产品可存放在随附的袋子中。
更换
每两年更换一次刀头以获得最佳的剃须效果。
损坏或磨损的剃须刀头只能用 HQ4+ 飞利浦剃
须刀头更换。
1 关闭剃须刀。
2 按下释放钮 (1)，取下剃须刀头部件 (2)。
3 向中间捏中央弹簧的两侧 (1)，并向上提起
取出固定架，将其从剃须刀头部件中取出
(2)。
,
,
简体中文18
19简体中文 19
4 将剃须刀头滑离固定架。
5 将新的剃须刀头滑入固定架。
6 将固定架重新安装到剃须刀头部件上。
7 将剃须刀头部件重新安装到剃须刀上。
附件
可选配以下附件：
HQ4 + 飞利浦剃须刀头。
HQ100 飞利浦剃须刀头清洁器（不在中国销
售）。
HQ101 飞利浦剃须刀头清洁液（不在中国销
售）。
HQ110 飞利浦剃须刀头清洁喷雾剂（不在中
国出售）
-
-
-
-
环保
弃置产品时，请不要将其与一般生活垃圾堆
放在一起；应将其交给官方指定的回收中
心。这样做有利于环保。
电池含有可污染环境的物质。在您丢弃产品
时，请将电池取出，或将其送到官方回收
点。在官方电池回收点处理电池。
处理电池
仅在电池电量完全耗尽后方可取出
电池。
1 从电源插座拔下剃须刀。
2 让剃须刀运转直到停止，拧下螺钉并打开剃
须刀。
3 取出电池。
取出电池后，不要再将剃须刀与电
源连接在一起。
保修与服务
如果您需要详细信息或有任何问题，请浏览飞
利浦网站，地址为 www.philips.com。您也可
以与本国的飞利浦顾客服务中心联系（您可以
从全球保修卡中找到电话号码）。如果本国没
有飞利浦顾客服务中心，请与当地的飞利浦经
销商或与飞利浦家庭小电器的维修中心联系。
由于剃须刀头（刀片和网罩）属于易磨损物
品，因此不在国际保修条款的涵盖范围之列。
-
-
简体中文20
简体中文 21
故障排除
1 剃须性能下降
原因 1：剃须刀头脏。剃须刀头未清洁干净，
或长时间未清洁。
在继续剃须之前，请先彻底清洗剃须刀。
见“清洁和保养”一章。
原因 2：过长的胡须堵塞了剃须刀头。
用随附的刷子清洁刀片和网罩。见“清洁和保
养”中“每两个月：剃须刀头”部分。
原因 3：剃须刀头已损坏或磨损。
更换剃须刀头。见“更换”一章。
2 向上推开/关时，剃须刀不工作。
原因：电池电量耗尽。
给电池充电。见“充电”一章。
-
-
-
-
2007/11/26
22
4222.002.4228.9
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
